# After beacon calibrate and save config klipper unable to recognise default **URL:** \ **Category:** General Discussion\ **Created:** [October 12, 2024, 9:19pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360 "2024-10-12T21:19:38Z")\ **Posts on this page:** 20\ **Page:** 1
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 12, 2024, 9:19pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/1 "2024-10-12T21:19:38Z")
### Basic Information: Printer Model: Voron 2.4 MCU / Printerboard: BTT Octopus V1.1 Host / SBC : Raspberry Pi 4b klippy.log Hi I recently installed Beacon H in my voron 2.4 The issue I have is when I Beacon\_calibrate I am only allowed to use to down arrow for the Z access at 01mm. No finer adjustment is able to be activated. If I press accept the becon calibrated is then accepted. However if I then save\_ config the mainsail posts a message “no beacon type registered” which means Beacon default is not accepted by klipper. I am stuck here and cannot procede. … ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 13, 2024, 3:11am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/2 "2024-10-13T03:11:53Z")
Please attach as requested the klippy.log. And in this case also the complete printer.cfg. Both to your next post. ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 13, 2024, 8:21pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/3 "2024-10-13T20:21:06Z")
Klippy log and printer.config as requested [klippy (20).zip](https://klipper.discourse.group/uploads/short-url/uYVJCW7wDQZg40sOZoBxbtx40y0.zip) (9.8 KB) ```auto # This file contains common pin mappings for the BigTreeTech Octopus V1. # To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader" # Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference # after running "make", copy the generated "klipper/out/klipper.bin" file to a # file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card. # See docs/Config_Reference.md for a description of parameters. ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## ***THINGS TO CHANGE/CHECK:*** ## MCU paths [mcu] section ## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types ## Hotend heater pin [extruder] section ## Z Endstop Switch location [safe_z_home] section ## Homing end position [gcode_macro G32] section ## Z Endstop Switch offset for Z0 [stepper_z] section ## Stepper Z1 enable pin [stepper_z1] section ## Probe points [quad_gantry_level] section ## Min & Max gantry corner postions [quad_gantry_level] section ## PID tune [extruder] and [heater_bed] sections ## Probe pin [probe] section ## Fine tune E steps [extruder] section [include btt_ebb-sb2240.cfg] [include mainsail.cfg] #[exclude_object] #[include Adaptive_mesh.cfg] #[include KAMP_Settings.cfg] #[include voron_purge.cfg] #[include line_purge.cfg] [mcu] ## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_060025000E5053424E363620-if00 restart_method: command ##-------------------------------------------------------------------- [printer] kinematics: corexy max_velocity: 300 max_accel: 3000 #Max 4000 max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 ##################################################################### # X/Y Stepper Settings ##################################################################### ## B Stepper - Left ## Connected to MOTOR_0 ## Endstop connected to DIAG_0 [stepper_x] step_pin: PF13 dir_pin: PF12 enable_pin: !PF14 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper endstop_pin: PG6 position_min: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position_endstop: 250 #position_max: 250 ## Uncomment for 300mm build #position_endstop: 300 #position_max: 300 ## Uncomment for 350mm build position_endstop: 350 position_max: 350 ##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_x] uart_pin: PC4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## A Stepper - Right ## Connected to MOTOR_1 ## Endstop connected to DIAG_1 [stepper_y] step_pin: PG0 dir_pin: PG1 enable_pin: !PF15 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper endstop_pin: PG9 position_min: 0 ##-------------------------------------------------------------------- ## Uncomment for 250mm build #position_endstop: 250 #position_max: 250 ## Uncomment for 300mm build #position_endstop: 300 #position_max: 300 ## Uncomment for 350mm build position_endstop: 350 position_max: 350 ##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_y] uart_pin: PD11 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Z Stepper Settings ##################################################################### ## Z0 Stepper - Front Left ## Connected to MOTOR_2 ## Endstop connected to DIAG_2 [stepper_z] step_pin: PF11 dir_pin: PG3 enable_pin: !PG5 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 endstop_pin: probe: z_virtual_endstop ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config #position_endstop: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position_max: 210 ## Uncomment below for 300mm build #position_max: 260 ## Uncomment below for 350mm build position_max: 350 ##-------------------------------------------------------------------- position_min: -5 homing_speed: 8 second_homing_speed: 3 homing_retract_dist: 0 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z] uart_pin: PC6 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z1 Stepper - Rear Left ## Connected to MOTOR_3 [stepper_z1] step_pin: PG4 dir_pin: !PC1 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 enable_pin: !PA0 ## Octopus PRO 1.1 #enable_pin: !PA2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z1] uart_pin: PC7 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z2 Stepper - Rear Right ## Connected to MOTOR_4 [stepper_z2] step_pin: PF9 dir_pin: PF10 enable_pin: !PG2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z2] uart_pin: PF2 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z3 Stepper - Front Right ## Connected to MOTOR_5 [stepper_z3] step_pin: PC13 dir_pin: !PF0 enable_pin: !PF1 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z3] uart_pin: PE4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Extruder ##################################################################### ## Connected to MOTOR_6 ## Heater - HE0 ## Thermistor - T0 #[extruder] #step_pin: PE2 #dir_pin: PE3 #enable_pin: !PD4 ## Update value below when you perform extruder calibration ## If you ask for 100mm of filament, but in reality it is 98mm: ## rotation_distance = * / 100 ## 22.6789511 is a good starting point #rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears ## Update Gear Ratio depending on your Extruder Type ## Use 50:10 for Stealthburner/Clockwork 2 ## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) ## Use 80:20 for M4, M3.1 #gear_ratio: 50:10 #microsteps: 32 #full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree #nozzle_diameter: 0.400 #filament_diameter: 1.75 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 #heater_pin: PA2 ## Octopus PRO 1.1 #heater_pin: PA0 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for NTC 100k 3950 thermistors #sensor_type: Generic 3950 #sensor_pin: PF4 #min_temp: -100 #max_temp: 270 #max_power: 1.0 #min_extrude_temp: 170 #control = pid #pid_kp = 26.213 #pid_ki = 1.304 #pid_kd = 131.721 ## Try to keep pressure_advance below 1.0 #pressure_advance: 0.05 ## Default is 0.040, leave stock #pressure_advance_smooth_time: 0.040 ## E0 on MOTOR6 ## Make sure to update below for your relevant driver (2208 or 2209) #[tmc2209 extruder] #uart_pin: PE1 #interpolate: false #run_current: 0.5 #sense_resistor: 0.110 #stealthchop_threshold: 0 ##################################################################### # Bed Heater ##################################################################### ## SSR Pin - HE1 ## Thermistor - TB [heater_bed] ## Uncomment the following line if using the default SSR wiring from the docs site heater_pin: PA3 ## Other wiring guides may use BED_OUT to control the SSR. Uncomment the following line for those cases #heater_pin: PA1 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for Keenovo heaters sensor_type: Generic 3950 sensor_pin: PF3 ## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink. ## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power" ## If max_power is greater than 1.0, use 1.0 max_power: 0.6 min_temp: 0 max_temp: 120 control: pid pid_kp: 58.437 pid_ki: 2.347 pid_kd: 363.769 ##################################################################### # Probe ##################################################################### [beacon] serial: /dev/serial/by-id/usb-Beacon_Beacon_RevH_06F0EB985154364134202020FF142909-if00 x_offset: -20 # update with offset from nozzle on your machine y_offset: 0 # update with offset from nozzle on your machine mesh_main_direction: x mesh_runs: 2 [safe_z_home] home_xy_position: 175, 175 # update for your machine z_hop: 3 [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 10, 10 mesh_max: 300, 300 probe_count: 5, 3 mesh_pps: 2, 3 algorithm: bicubic bicubic_tension: 0.2 ## Inductive Probe ## This probe is not used for Z height, only Quad Gantry Leveling ##[probe] #-------------------------------------------------------------------- ## Select the probe port by type: ## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V. #pin: ~!PB7 ## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO. #pin: PG15 ## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper #pin: ~!PC5 #-------------------------------------------------------------------- #x_offset: 0 #y_offset: 25.0 #z_offset: 0 #speed: 10.0 #samples: 3 #samples_result: median #sample_retract_dist: 3.0 #samples_tolerance: 0.006 #samples_tolerance_retries: 3 ##################################################################### # Fan Control ##################################################################### ## Print Cooling Fan - FAN0 #[fan] #pin: PA8 #kick_start_time: 0.5 ## Depending on your fan, you may need to increase this value ## if your fan will not start. Can change cycle_time (increase) ## if your fan is not able to slow down effectively #off_below: 0.10 ## Hotend Fan - FAN1 #[heater_fan hotend_fan] #pin: PE5 #max_power: 1.0 #kick_start_time: 0.5 #heater: extruder #heater_temp: 50.0 ## If you are experiencing back flow, you can reduce fan_speed #fan_speed: 1.0 ## Controller fan - FAN2 [controller_fan controller_fan] pin: PD12 kick_start_time: 0.5 heater: heater_bed ## Exhaust fan - FAN3 #[heater_fan exhaust_fan] #pin: PD13 #max_power: 1.0 #shutdown_speed: 0.0 #kick_start_time: 5.0 #heater: heater_bed #heater_temp: 60 #fan_speed: 1.0 ##################################################################### # LED Control ##################################################################### ## Chamber Lighting - HE2 Connector (Optional) #[output_pin caselight] ##Octopus 1.0 & 1.1, Octopus PRO 1.0 #pin: PB10 ##Octopus PRO 1.1 #pin: PB0 #pwm:true #shutdown_value: 0 #value:1 #cycle_time: 0.01 ##################################################################### # Homing and Gantry Adjustment Routines ##################################################################### [idle_timeout] timeout: 1800 ## Use QUAD_GANTRY_LEVEL to level a gantry. ## Min & Max gantry corners - measure from nozzle at MIN (0,0) and ## MAX (250, 250), (300,300), or (350,350) depending on your printer size ## to respective belt positions #-------------------------------------------------------------------- ## Gantry Corners for 250mm Build ## Uncomment for 250mm build #gantry_corners: # -60,-10 # 310, 320 ## Probe points #points: # 50,25 # 50,175 # 200,175 # 200,25 ## Gantry Corners for 300mm Build ## Uncomment for 300mm build #gantry_corners: # -60,-10 # 360,370 ## Probe points #points: # 50,25 # 50,225 # 250,225 # 250,25 ## Gantry Corners for 350mm Build ## Uncomment for 350mm build #gantry_corners: #-60,-10 #410,420 ## Probe points #points: #50,25 #50,275 #300,275 #300,25 #-------------------------------------------------------------------- #speed: 100 #horizontal_move_z: 10 #retries: 5 #retry_tolerance: 0.0075 #max_adjust: 10 ######################################## # EXP1 / EXP2 (display) pins ######################################## [board_pins] aliases: # EXP1 header EXP1_1=PE8, EXP1_2=PE7, EXP1_3=PE9, EXP1_4=PE10, EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side EXP1_7=PE14, EXP1_8=PE15, EXP1_9=, EXP1_10=<5V>, # EXP2 header EXP2_1=PA6, EXP2_2=PA5, EXP2_3=PB1, EXP2_4=PA4, EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side EXP2_7=PC15, EXP2_8=, EXP2_9=, EXP2_10=<5V> ##################################################################### # Displays ##################################################################### ## Uncomment the display that you have #-------------------------------------------------------------------- ## RepRapDiscount 128x64 Full Graphic Smart Controller #[display] #lcd_type: st7920 #cs_pin: EXP1_4 #sclk_pin: EXP1_5 #sid_pin: EXP1_3 #menu_timeout: 40 #encoder_pins: ^EXP2_5, ^EXP2_3 #click_pin: ^!EXP1_2 #[output_pin beeper] #pin: EXP1_1 #-------------------------------------------------------------------- ## mini12864 LCD Display #[display] #lcd_type: uc1701 #cs_pin: EXP1_3 #a0_pin: EXP1_4 #rst_pin: EXP1_5 #encoder_pins: ^EXP2_5, ^EXP2_3 #click_pin: ^!EXP1_2 #contrast: 63 #spi_software_miso_pin: EXP2_1 #spi_software_mosi_pin: EXP2_6 #spi_software_sclk_pin: EXP2_2 ## To control Neopixel RGB in mini12864 display #[neopixel btt_mini12864] #pin: EXP1_6 #chain_count: 3 #initial_RED: 0.1 #initial_GREEN: 0.5 #initial_BLUE: 0.0 #color_order: RGB ## Set RGB values on boot up for each Neopixel. ## Index 1 = display, Index 2 and 3 = Knob #[delayed_gcode setdisplayneopixel] #initial_duration: 1 #gcode: # SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 # SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 # SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 #-------------------------------------------------------------------- ##################################################################### # Macros ##################################################################### [gcode_macro PARK] gcode: {% set th = printer.toolhead %} G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y//2} Z30 [gcode_macro G32] gcode: SAVE_GCODE_STATE NAME=STATE_G32 G90 G28 QUAD_GANTRY_LEVEL G28 PARK RESTORE_GCODE_STATE NAME=STATE_G32 [gcode_macro PRINT_START] # Use PRINT_START for the slicer starting script - please customise for your slicer of choice gcode: G32 ; home all axes G90 ; absolute positioning G1 Z20 F3000 ; move nozzle away from bed bed_mesh_clear Bed_mesh_calibrate voron_purge line_purge [gcode_macro PRINT_END] # Use PRINT_END for the slicer ending script - please customise for your slicer of choice gcode: # safe anti-stringing move coords {% set th = printer.toolhead %} {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %} {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %} {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %} SAVE_GCODE_STATE NAME=STATE_PRINT_END M400 ; wait for buffer to clear G92 E0 ; zero the extruder G1 E-5.0 F1800 ; retract filament TURN_OFF_HEATERS G90 ; absolute positioning G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear M107 ; turn off fan BED_MESH_CLEAR # The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE # command pair is to restore the printer's coordinate system # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.+ #*# reg_drive_current = 15 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7411078741184864, #*# 2.0282736731701902, #*# 0.6862528830345038, #*# 0.3486093067747865, #*# 0.16530108376973393, #*# -0.12163665562446468, #*# -0.05862986736543908, #*# 0.2452631713667019, #*# 0.06819765879742178, #*# -0.09611906443345801 #*# model_domain = 1.9240001689671922e-07,1.94294272461105e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.748053 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7067806489191413, #*# 2.012188591634574, #*# 0.6926714877472473, #*# 0.3119900200087614, #*# 0.20334153899145777, #*# -0.022593663079803088, #*# -0.06994937379891607, #*# 0.16887774609529993, #*# 0.0722456879061055, #*# -0.06351006089271206 #*# model_domain = 1.915421321607789e-07,1.9411589290898408e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 17.426948 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7614442812018936, #*# 2.0473591186310696, #*# 0.7168272264936951, #*# 0.39628061141359183, #*# 0.01313507143947696, #*# -0.38121931711807944, #*# 0.13172756012761982, #*# 0.6002881682710194, #*# -0.017420273453729623, #*# -0.2545809693853755 #*# model_domain = 1.9269679204207e-07,1.9435768235056183e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 18.089880 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7055151835074758, #*# 2.0126615352461403, #*# 0.681363527234212, #*# 0.27721032699374687, #*# 0.2677438651147289, #*# 0.16261667108254918, #*# -0.19160765825537743, #*# -0.12905302471922508, #*# 0.1412986768176732, #*# 0.08518811226089557 #*# model_domain = 1.9162979251029213e-07,1.9413117887102388e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.418298 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.6970372354317966, #*# 1.996812336360698, #*# 0.7013133262000886, #*# 0.2471918104863108, #*# 0.19667592740612264, #*# 0.2591509556382915, #*# -0.06255297032824234, #*# -0.18891323110393396, #*# 0.07103259075263532, #*# 0.09118200068818301 #*# model_domain = 1.9125193410486744e-07,1.9405542164927475e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.883046 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7138732037276572, #*# 2.0034022701461596, #*# 0.7041446918390303, #*# 0.30667724721363016, #*# 0.14930539049244385, #*# 0.10751009214461864, #*# -0.006789349200466126, #*# -0.0470556392104273, #*# 0.04277715934782651, #*# 0.0351523927017796 #*# model_domain = 1.9175819325865713e-07,1.941554600818759e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 23.380527 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7427534471474244, #*# 2.0479603806709905, #*# 0.6795041008104327, #*# 0.256577892886551, #*# 0.21476321214624003, #*# 0.15306741946285482, #*# -0.13597213587105095, #*# -0.10238405719770477, #*# 0.10168745460437788, #*# 0.051597440302921856 #*# model_domain = 1.9242412144881197e-07,1.943308580498378e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 20.624486 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.808022, -0.685457, -0.620456, -0.537661, -0.418332 #*# 0.372761, 0.154378, -0.054844, -0.227493, -0.360822 #*# 1.362267, 0.979261, 0.539283, 0.086328, -0.130129 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 5.0 #*# max_x = 310.0 #*# min_y = 5.0 #*# max_y = 310.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.6907648131225812, #*# 1.9766848887014146, #*# 0.7013804773249704, #*# 0.34017875253421187, #*# 0.16670689623999116, #*# 0.017904562865218087, #*# 0.004592282954174283, #*# 0.07186101641119913, #*# 0.03827998394000279, #*# -0.002774969253180517 #*# model_domain = 1.9093146680793573e-07,1.9402355920135718e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 20.789928 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.691960, -0.606158, -0.556534, -0.469763, -0.329971 #*# 0.423036, 0.200318, -0.004589, -0.174587, -0.292900 #*# 1.412675, 1.022134, 0.585692, 0.141770, -0.056444 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 5.0 #*# max_x = 310.0 #*# min_y = 5.0 #*# max_y = 310.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.682772670823201, #*# 1.971610789976209, #*# 0.6909513221065361, #*# 0.3280226916794054, #*# 0.1945783028203591, #*# 0.060408184043791315, #*# -0.00899956945603164, #*# 0.05116785179219562, #*# 0.04154129453476751, #*# -0.006786246656079006 #*# model_domain = 1.9072210099147046e-07,1.9398653418160353e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.024338 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.607388, -0.549764, -0.511448, -0.438259, -0.297314 #*# 0.412229, 0.203914, 0.012126, -0.144278, -0.254201 #*# 1.324851, 0.970689, 0.568767, 0.162417, -0.035212 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 10.0 #*# max_x = 300.0 #*# min_y = 10.0 #*# max_y = 300.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.6866412922095426, #*# 1.9736809327161986, #*# 0.6807035951950957, #*# 0.30613972342144596, #*# 0.23130102848878253, #*# 0.16004947199847477, #*# -0.07079576527962453, #*# -0.1120383520654977, #*# 0.07396622433721763, #*# 0.07706357059550537 #*# model_domain = 1.90739737390908e-07,1.9398956672238156e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 23.418544 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.598195, -0.539282, -0.501455, -0.431144, -0.295663 #*# 0.409153, 0.200007, 0.008834, -0.147293, -0.259983 #*# 1.311845, 0.956247, 0.554468, 0.148269, -0.046679 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 3 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 10.0 #*# max_x = 300.0 #*# min_y = 10.0 #*# max_y = 300.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.692625508502522, #*# 1.9779147624532591, #*# 0.651592476521398, #*# 0.2871243223497995, #*# 0.33012070899153356, #*# 0.1819285534728437, #*# -0.22096522497204713, #*# -0.12649524857836372, #*# 0.14836284196944036, #*# 0.08391052674543667 #*# model_domain = 1.9082333987938336e-07,1.9400658866095255e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 20.329977 #*# model_offset = 0.00000 ``` ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 14, 2024, 3:13am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/4 "2024-10-14T03:13:20Z")
Please also the printer.cfg as a file! and not Copy & Paste. At least use the `Preformatted Text` feature of the forum editor. ![Format](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/6/643ab9def96b03089cfb0c194628129fcc96b3f8.png) The way you did it, the data is not usable at all. BTW: You have 12 (!) config blocks. That can not work. ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 14, 2024, 8:00pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/5 "2024-10-14T20:00:23Z")
```auto # This file contains common pin mappings for the BigTreeTech Octopus V1. # To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader" # Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference # after running "make", copy the generated "klipper/out/klipper.bin" file to a # file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card. # See docs/Config_Reference.md for a description of parameters. ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## ***THINGS TO CHANGE/CHECK:*** ## MCU paths [mcu] section ## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types ## Hotend heater pin [extruder] section ## Z Endstop Switch location [safe_z_home] section ## Homing end position [gcode_macro G32] section ## Z Endstop Switch offset for Z0 [stepper_z] section ## Stepper Z1 enable pin [stepper_z1] section ## Probe points [quad_gantry_level] section ## Min & Max gantry corner postions [quad_gantry_level] section ## PID tune [extruder] and [heater_bed] sections ## Probe pin [probe] section ## Fine tune E steps [extruder] section [include btt_ebb-sb2240.cfg] [include mainsail.cfg] #[exclude_object] #[include Adaptive_mesh.cfg] #[include KAMP_Settings.cfg] #[include voron_purge.cfg] #[include line_purge.cfg] [mcu] ## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_060025000E5053424E363620-if00 restart_method: command ##-------------------------------------------------------------------- [printer] kinematics: corexy max_velocity: 300 max_accel: 3000 #Max 4000 max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 ##################################################################### # X/Y Stepper Settings ##################################################################### ## B Stepper - Left ## Connected to MOTOR_0 ## Endstop connected to DIAG_0 [stepper_x] step_pin: PF13 dir_pin: PF12 enable_pin: !PF14 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper endstop_pin: PG6 position_min: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position_endstop: 250 #position_max: 250 ## Uncomment for 300mm build #position_endstop: 300 #position_max: 300 ## Uncomment for 350mm build position_endstop: 350 position_max: 350 ##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_x] uart_pin: PC4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## A Stepper - Right ## Connected to MOTOR_1 ## Endstop connected to DIAG_1 [stepper_y] step_pin: PG0 dir_pin: PG1 enable_pin: !PF15 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper endstop_pin: PG9 position_min: 0 ##-------------------------------------------------------------------- ## Uncomment for 250mm build #position_endstop: 250 #position_max: 250 ## Uncomment for 300mm build #position_endstop: 300 #position_max: 300 ## Uncomment for 350mm build position_endstop: 350 position_max: 350 ##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_y] uart_pin: PD11 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Z Stepper Settings ##################################################################### ## Z0 Stepper - Front Left ## Connected to MOTOR_2 ## Endstop connected to DIAG_2 [stepper_z] step_pin: PF11 dir_pin: PG3 enable_pin: !PG5 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 endstop_pin: probe: z_virtual_endstop ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config #position_endstop: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position_max: 210 ## Uncomment below for 300mm build #position_max: 260 ## Uncomment below for 350mm build position_max: 350 ##-------------------------------------------------------------------- position_min: -5 homing_speed: 8 second_homing_speed: 3 homing_retract_dist: 0 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z] uart_pin: PC6 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z1 Stepper - Rear Left ## Connected to MOTOR_3 [stepper_z1] step_pin: PG4 dir_pin: !PC1 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 enable_pin: !PA0 ## Octopus PRO 1.1 #enable_pin: !PA2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z1] uart_pin: PC7 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z2 Stepper - Rear Right ## Connected to MOTOR_4 [stepper_z2] step_pin: PF9 dir_pin: PF10 enable_pin: !PG2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z2] uart_pin: PF2 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z3 Stepper - Front Right ## Connected to MOTOR_5 [stepper_z3] step_pin: PC13 dir_pin: !PF0 enable_pin: !PF1 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z3] uart_pin: PE4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Extruder ##################################################################### ## Connected to MOTOR_6 ## Heater - HE0 ## Thermistor - T0 #[extruder] #step_pin: PE2 #dir_pin: PE3 #enable_pin: !PD4 ## Update value below when you perform extruder calibration ## If you ask for 100mm of filament, but in reality it is 98mm: ## rotation_distance = * / 100 ## 22.6789511 is a good starting point #rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears ## Update Gear Ratio depending on your Extruder Type ## Use 50:10 for Stealthburner/Clockwork 2 ## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) ## Use 80:20 for M4, M3.1 #gear_ratio: 50:10 #microsteps: 32 #full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree #nozzle_diameter: 0.400 #filament_diameter: 1.75 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 #heater_pin: PA2 ## Octopus PRO 1.1 #heater_pin: PA0 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for NTC 100k 3950 thermistors #sensor_type: Generic 3950 #sensor_pin: PF4 #min_temp: -100 #max_temp: 270 #max_power: 1.0 #min_extrude_temp: 170 #control = pid #pid_kp = 26.213 #pid_ki = 1.304 #pid_kd = 131.721 ## Try to keep pressure_advance below 1.0 #pressure_advance: 0.05 ## Default is 0.040, leave stock #pressure_advance_smooth_time: 0.040 ## E0 on MOTOR6 ## Make sure to update below for your relevant driver (2208 or 2209) #[tmc2209 extruder] #uart_pin: PE1 #interpolate: false #run_current: 0.5 #sense_resistor: 0.110 #stealthchop_threshold: 0 ##################################################################### # Bed Heater ##################################################################### ## SSR Pin - HE1 ## Thermistor - TB [heater_bed] ## Uncomment the following line if using the default SSR wiring from the docs site heater_pin: PA3 ## Other wiring guides may use BED_OUT to control the SSR. Uncomment the following line for those cases #heater_pin: PA1 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for Keenovo heaters sensor_type: Generic 3950 sensor_pin: PF3 ## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink. ## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power" ## If max_power is greater than 1.0, use 1.0 max_power: 0.6 min_temp: 0 max_temp: 120 control: pid pid_kp: 58.437 pid_ki: 2.347 pid_kd: 363.769 ##################################################################### # Probe ##################################################################### [beacon] serial: /dev/serial/by-id/usb-Beacon_Beacon_RevH_06F0EB985154364134202020FF142909-if00 x_offset: -20 # update with offset from nozzle on your machine y_offset: 0 # update with offset from nozzle on your machine mesh_main_direction: x mesh_runs: 2 [safe_z_home] home_xy_position: 175, 175 # update for your machine z_hop: 3 [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 10, 10 mesh_max: 300, 300 probe_count: 5, 3 mesh_pps: 2, 3 algorithm: bicubic bicubic_tension: 0.2 ## Inductive Probe ## This probe is not used for Z height, only Quad Gantry Leveling ##[probe] #-------------------------------------------------------------------- ## Select the probe port by type: ## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V. #pin: ~!PB7 ## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO. #pin: PG15 ## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper #pin: ~!PC5 #-------------------------------------------------------------------- #x_offset: 0 #y_offset: 25.0 #z_offset: 0 #speed: 10.0 #samples: 3 #samples_result: median #sample_retract_dist: 3.0 #samples_tolerance: 0.006 #samples_tolerance_retries: 3 ##################################################################### # Fan Control ##################################################################### ## Print Cooling Fan - FAN0 #[fan] #pin: PA8 #kick_start_time: 0.5 ## Depending on your fan, you may need to increase this value ## if your fan will not start. Can change cycle_time (increase) ## if your fan is not able to slow down effectively #off_below: 0.10 ## Hotend Fan - FAN1 #[heater_fan hotend_fan] #pin: PE5 #max_power: 1.0 #kick_start_time: 0.5 #heater: extruder #heater_temp: 50.0 ## If you are experiencing back flow, you can reduce fan_speed #fan_speed: 1.0 ## Controller fan - FAN2 [controller_fan controller_fan] pin: PD12 kick_start_time: 0.5 heater: heater_bed ## Exhaust fan - FAN3 #[heater_fan exhaust_fan] #pin: PD13 #max_power: 1.0 #shutdown_speed: 0.0 #kick_start_time: 5.0 #heater: heater_bed #heater_temp: 60 #fan_speed: 1.0 ##################################################################### # LED Control ##################################################################### ## Chamber Lighting - HE2 Connector (Optional) #[output_pin caselight] ##Octopus 1.0 & 1.1, Octopus PRO 1.0 #pin: PB10 ##Octopus PRO 1.1 #pin: PB0 #pwm:true #shutdown_value: 0 #value:1 #cycle_time: 0.01 ##################################################################### # Homing and Gantry Adjustment Routines ##################################################################### [idle_timeout] timeout: 1800 ## Use QUAD_GANTRY_LEVEL to level a gantry. ## Min & Max gantry corners - measure from nozzle at MIN (0,0) and ## MAX (250, 250), (300,300), or (350,350) depending on your printer size ## to respective belt positions #-------------------------------------------------------------------- ## Gantry Corners for 250mm Build ## Uncomment for 250mm build #gantry_corners: # -60,-10 # 310, 320 ## Probe points #points: # 50,25 # 50,175 # 200,175 # 200,25 ## Gantry Corners for 300mm Build ## Uncomment for 300mm build #gantry_corners: # -60,-10 # 360,370 ## Probe points #points: # 50,25 # 50,225 # 250,225 # 250,25 ## Gantry Corners for 350mm Build ## Uncomment for 350mm build #gantry_corners: #-60,-10 #410,420 ## Probe points #points: #50,25 #50,275 #300,275 #300,25 #-------------------------------------------------------------------- #speed: 100 #horizontal_move_z: 10 #retries: 5 #retry_tolerance: 0.0075 #max_adjust: 10 ######################################## # EXP1 / EXP2 (display) pins ######################################## [board_pins] aliases: # EXP1 header EXP1_1=PE8, EXP1_2=PE7, EXP1_3=PE9, EXP1_4=PE10, EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side EXP1_7=PE14, EXP1_8=PE15, EXP1_9=, EXP1_10=<5V>, # EXP2 header EXP2_1=PA6, EXP2_2=PA5, EXP2_3=PB1, EXP2_4=PA4, EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side EXP2_7=PC15, EXP2_8=, EXP2_9=, EXP2_10=<5V> ##################################################################### # Displays ##################################################################### ## Uncomment the display that you have #-------------------------------------------------------------------- ## RepRapDiscount 128x64 Full Graphic Smart Controller #[display] #lcd_type: st7920 #cs_pin: EXP1_4 #sclk_pin: EXP1_5 #sid_pin: EXP1_3 #menu_timeout: 40 #encoder_pins: ^EXP2_5, ^EXP2_3 #click_pin: ^!EXP1_2 #[output_pin beeper] #pin: EXP1_1 #-------------------------------------------------------------------- ## mini12864 LCD Display #[display] #lcd_type: uc1701 #cs_pin: EXP1_3 #a0_pin: EXP1_4 #rst_pin: EXP1_5 #encoder_pins: ^EXP2_5, ^EXP2_3 #click_pin: ^!EXP1_2 #contrast: 63 #spi_software_miso_pin: EXP2_1 #spi_software_mosi_pin: EXP2_6 #spi_software_sclk_pin: EXP2_2 ## To control Neopixel RGB in mini12864 display #[neopixel btt_mini12864] #pin: EXP1_6 #chain_count: 3 #initial_RED: 0.1 #initial_GREEN: 0.5 #initial_BLUE: 0.0 #color_order: RGB ## Set RGB values on boot up for each Neopixel. ## Index 1 = display, Index 2 and 3 = Knob #[delayed_gcode setdisplayneopixel] #initial_duration: 1 #gcode: # SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 # SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 # SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 #-------------------------------------------------------------------- ##################################################################### # Macros ##################################################################### [gcode_macro PARK] gcode: {% set th = printer.toolhead %} G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y//2} Z30 [gcode_macro G32] gcode: SAVE_GCODE_STATE NAME=STATE_G32 G90 G28 QUAD_GANTRY_LEVEL G28 PARK RESTORE_GCODE_STATE NAME=STATE_G32 [gcode_macro PRINT_START] # Use PRINT_START for the slicer starting script - please customise for your slicer of choice gcode: G32 ; home all axes G90 ; absolute positioning G1 Z20 F3000 ; move nozzle away from bed bed_mesh_clear Bed_mesh_calibrate voron_purge line_purge [gcode_macro PRINT_END] # Use PRINT_END for the slicer ending script - please customise for your slicer of choice gcode: # safe anti-stringing move coords {% set th = printer.toolhead %} {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %} {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %} {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %} SAVE_GCODE_STATE NAME=STATE_PRINT_END M400 ; wait for buffer to clear G92 E0 ; zero the extruder G1 E-5.0 F1800 ; retract filament TURN_OFF_HEATERS G90 ; absolute positioning G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear M107 ; turn off fan BED_MESH_CLEAR # The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE # command pair is to restore the printer's coordinate system # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.+ #*# reg_drive_current = 15 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7411078741184864, #*# 2.0282736731701902, #*# 0.6862528830345038, #*# 0.3486093067747865, #*# 0.16530108376973393, #*# -0.12163665562446468, #*# -0.05862986736543908, #*# 0.2452631713667019, #*# 0.06819765879742178, #*# -0.09611906443345801 #*# model_domain = 1.9240001689671922e-07,1.94294272461105e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.748053 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7067806489191413, #*# 2.012188591634574, #*# 0.6926714877472473, #*# 0.3119900200087614, #*# 0.20334153899145777, #*# -0.022593663079803088, #*# -0.06994937379891607, #*# 0.16887774609529993, #*# 0.0722456879061055, #*# -0.06351006089271206 #*# model_domain = 1.915421321607789e-07,1.9411589290898408e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 17.426948 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7614442812018936, #*# 2.0473591186310696, #*# 0.7168272264936951, #*# 0.39628061141359183, #*# 0.01313507143947696, #*# -0.38121931711807944, #*# 0.13172756012761982, #*# 0.6002881682710194, #*# -0.017420273453729623, #*# -0.2545809693853755 #*# model_domain = 1.9269679204207e-07,1.9435768235056183e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 18.089880 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7055151835074758, #*# 2.0126615352461403, #*# 0.681363527234212, #*# 0.27721032699374687, #*# 0.2677438651147289, #*# 0.16261667108254918, #*# -0.19160765825537743, #*# -0.12905302471922508, #*# 0.1412986768176732, #*# 0.08518811226089557 #*# model_domain = 1.9162979251029213e-07,1.9413117887102388e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.418298 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.6970372354317966, #*# 1.996812336360698, #*# 0.7013133262000886, #*# 0.2471918104863108, #*# 0.19667592740612264, #*# 0.2591509556382915, #*# -0.06255297032824234, #*# -0.18891323110393396, #*# 0.07103259075263532, #*# 0.09118200068818301 #*# model_domain = 1.9125193410486744e-07,1.9405542164927475e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.883046 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7138732037276572, #*# 2.0034022701461596, #*# 0.7041446918390303, #*# 0.30667724721363016, #*# 0.14930539049244385, #*# 0.10751009214461864, #*# -0.006789349200466126, #*# -0.0470556392104273, #*# 0.04277715934782651, #*# 0.0351523927017796 #*# model_domain = 1.9175819325865713e-07,1.941554600818759e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 23.380527 #*# model_offset = 0.00000 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.7427534471474244, #*# 2.0479603806709905, #*# 0.6795041008104327, #*# 0.256577892886551, #*# 0.21476321214624003, #*# 0.15306741946285482, #*# -0.13597213587105095, #*# -0.10238405719770477, #*# 0.10168745460437788, #*# 0.051597440302921856 #*# model_domain = 1.9242412144881197e-07,1.943308580498378e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 20.624486 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.808022, -0.685457, -0.620456, -0.537661, -0.418332 #*# 0.372761, 0.154378, -0.054844, -0.227493, -0.360822 #*# 1.362267, 0.979261, 0.539283, 0.086328, -0.130129 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 5.0 #*# max_x = 310.0 #*# min_y = 5.0 #*# max_y = 310.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.6907648131225812, #*# 1.9766848887014146, #*# 0.7013804773249704, #*# 0.34017875253421187, #*# 0.16670689623999116, #*# 0.017904562865218087, #*# 0.004592282954174283, #*# 0.07186101641119913, #*# 0.03827998394000279, #*# -0.002774969253180517 #*# model_domain = 1.9093146680793573e-07,1.9402355920135718e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 20.789928 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.691960, -0.606158, -0.556534, -0.469763, -0.329971 #*# 0.423036, 0.200318, -0.004589, -0.174587, -0.292900 #*# 1.412675, 1.022134, 0.585692, 0.141770, -0.056444 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 5.0 #*# max_x = 310.0 #*# min_y = 5.0 #*# max_y = 310.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.682772670823201, #*# 1.971610789976209, #*# 0.6909513221065361, #*# 0.3280226916794054, #*# 0.1945783028203591, #*# 0.060408184043791315, #*# -0.00899956945603164, #*# 0.05116785179219562, #*# 0.04154129453476751, #*# -0.006786246656079006 #*# model_domain = 1.9072210099147046e-07,1.9398653418160353e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 22.024338 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.607388, -0.549764, -0.511448, -0.438259, -0.297314 #*# 0.412229, 0.203914, 0.012126, -0.144278, -0.254201 #*# 1.324851, 0.970689, 0.568767, 0.162417, -0.035212 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 2 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 10.0 #*# max_x = 300.0 #*# min_y = 10.0 #*# max_y = 300.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.6866412922095426, #*# 1.9736809327161986, #*# 0.6807035951950957, #*# 0.30613972342144596, #*# 0.23130102848878253, #*# 0.16004947199847477, #*# -0.07079576527962453, #*# -0.1120383520654977, #*# 0.07396622433721763, #*# 0.07706357059550537 #*# model_domain = 1.90739737390908e-07,1.9398956672238156e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 23.418544 #*# model_offset = 0.00000 #*# #*# [bed_mesh default] #*# version = 1 #*# points = #*# -0.598195, -0.539282, -0.501455, -0.431144, -0.295663 #*# 0.409153, 0.200007, 0.008834, -0.147293, -0.259983 #*# 1.311845, 0.956247, 0.554468, 0.148269, -0.046679 #*# x_count = 5 #*# y_count = 3 #*# mesh_x_pps = 2 #*# mesh_y_pps = 3 #*# algo = lagrange #*# tension = 0.2 #*# min_x = 10.0 #*# max_x = 300.0 #*# min_y = 10.0 #*# max_y = 300.0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.692625508502522, #*# 1.9779147624532591, #*# 0.651592476521398, #*# 0.2871243223497995, #*# 0.33012070899153356, #*# 0.1819285534728437, #*# -0.22096522497204713, #*# -0.12649524857836372, #*# 0.14836284196944036, #*# 0.08391052674543667 #*# model_domain = 1.9082333987938336e-07,1.9400658866095255e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 20.329977 #*# model_offset = 0.00000 ``` ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 14, 2024, 8:36pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/6 "2024-10-14T20:36:46Z")
You still have way too many config block at the and ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 14, 2024, 9:01pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/7 "2024-10-14T21:01:21Z")
```auto # This file contains common pin mappings for the BigTreeTech Octopus V1. # To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader" # Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference # after running "make", copy the generated "klipper/out/klipper.bin" file to a # file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card. # See docs/Config_Reference.md for a description of parameters. ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## ***THINGS TO CHANGE/CHECK:*** ## MCU paths [mcu] section ## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types ## Hotend heater pin [extruder] section ## Z Endstop Switch location [safe_z_home] section ## Homing end position [gcode_macro G32] section ## Z Endstop Switch offset for Z0 [stepper_z] section ## Stepper Z1 enable pin [stepper_z1] section ## Probe points [quad_gantry_level] section ## Min & Max gantry corner postions [quad_gantry_level] section ## PID tune [extruder] and [heater_bed] sections ## Probe pin [probe] section ## Fine tune E steps [extruder] section [include btt_ebb-sb2240.cfg] [include mainsail.cfg] #[exclude_object] #[include Adaptive_mesh.cfg] #[include KAMP_Settings.cfg] #[include voron_purge.cfg] #[include line_purge.cfg] [mcu] ## Obtain definition by "ls /dev/serial/by-id/*" then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_060025000E5053424E363620-if00 restart_method: command ##-------------------------------------------------------------------- [printer] kinematics: corexy max_velocity: 300 max_accel: 3000 #Max 4000 max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V max_z_accel: 350 square_corner_velocity: 5.0 ##################################################################### # X/Y Stepper Settings ##################################################################### ## B Stepper - Left ## Connected to MOTOR_0 ## Endstop connected to DIAG_0 [stepper_x] step_pin: PF13 dir_pin: PF12 enable_pin: !PF14 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper endstop_pin: PG6 position_min: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position_endstop: 250 #position_max: 250 ## Uncomment for 300mm build #position_endstop: 300 #position_max: 300 ## Uncomment for 350mm build position_endstop: 350 position_max: 350 ##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_x] uart_pin: PC4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## A Stepper - Right ## Connected to MOTOR_1 ## Endstop connected to DIAG_1 [stepper_y] step_pin: PG0 dir_pin: PG1 enable_pin: !PF15 rotation_distance: 40 microsteps: 32 full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper endstop_pin: PG9 position_min: 0 ##-------------------------------------------------------------------- ## Uncomment for 250mm build #position_endstop: 250 #position_max: 250 ## Uncomment for 300mm build #position_endstop: 300 #position_max: 300 ## Uncomment for 350mm build position_endstop: 350 position_max: 350 ##-------------------------------------------------------------------- homing_speed: 25 #Max 100 homing_retract_dist: 5 homing_positive_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_y] uart_pin: PD11 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Z Stepper Settings ##################################################################### ## Z0 Stepper - Front Left ## Connected to MOTOR_2 ## Endstop connected to DIAG_2 [stepper_z] step_pin: PF11 dir_pin: PG3 enable_pin: !PG5 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 endstop_pin: probe: z_virtual_endstop ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position_endstop brings nozzle closer to the bed ## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config #position_endstop: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position_max: 210 ## Uncomment below for 300mm build #position_max: 260 ## Uncomment below for 350mm build position_max: 350 ##-------------------------------------------------------------------- position_min: -5 homing_speed: 8 second_homing_speed: 3 homing_retract_dist: 0 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z] uart_pin: PC6 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z1 Stepper - Rear Left ## Connected to MOTOR_3 [stepper_z1] step_pin: PG4 dir_pin: !PC1 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 enable_pin: !PA0 ## Octopus PRO 1.1 #enable_pin: !PA2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z1] uart_pin: PC7 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z2 Stepper - Rear Right ## Connected to MOTOR_4 [stepper_z2] step_pin: PF9 dir_pin: PF10 enable_pin: !PG2 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z2] uart_pin: PF2 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ## Z3 Stepper - Front Right ## Connected to MOTOR_5 [stepper_z3] step_pin: PC13 dir_pin: !PF0 enable_pin: !PF1 rotation_distance: 40 gear_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z3] uart_pin: PE4 interpolate: false run_current: 0.8 sense_resistor: 0.110 stealthchop_threshold: 0 ##################################################################### # Extruder ##################################################################### ## Connected to MOTOR_6 ## Heater - HE0 ## Thermistor - T0 #[extruder] #step_pin: PE2 #dir_pin: PE3 #enable_pin: !PD4 ## Update value below when you perform extruder calibration ## If you ask for 100mm of filament, but in reality it is 98mm: ## rotation_distance = * / 100 ## 22.6789511 is a good starting point #rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears ## Update Gear Ratio depending on your Extruder Type ## Use 50:10 for Stealthburner/Clockwork 2 ## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) ## Use 80:20 for M4, M3.1 #gear_ratio: 50:10 #microsteps: 32 #full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree #nozzle_diameter: 0.400 #filament_diameter: 1.75 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 #heater_pin: PA2 ## Octopus PRO 1.1 #heater_pin: PA0 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for NTC 100k 3950 thermistors #sensor_type: Generic 3950 #sensor_pin: PF4 #min_temp: -100 #max_temp: 270 #max_power: 1.0 #min_extrude_temp: 170 #control = pid #pid_kp = 26.213 #pid_ki = 1.304 #pid_kd = 131.721 ## Try to keep pressure_advance below 1.0 #pressure_advance: 0.05 ## Default is 0.040, leave stock #pressure_advance_smooth_time: 0.040 ## E0 on MOTOR6 ## Make sure to update below for your relevant driver (2208 or 2209) #[tmc2209 extruder] #uart_pin: PE1 #interpolate: false #run_current: 0.5 #sense_resistor: 0.110 #stealthchop_threshold: 0 ##################################################################### # Bed Heater ##################################################################### ## SSR Pin - HE1 ## Thermistor - TB [heater_bed] ## Uncomment the following line if using the default SSR wiring from the docs site heater_pin: PA3 ## Other wiring guides may use BED_OUT to control the SSR. Uncomment the following line for those cases #heater_pin: PA1 ## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. ## Use "Generic 3950" for Keenovo heaters sensor_type: Generic 3950 sensor_pin: PF3 ## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink. ## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power" ## If max_power is greater than 1.0, use 1.0 max_power: 0.6 min_temp: 0 max_temp: 120 control: pid pid_kp: 58.437 pid_ki: 2.347 pid_kd: 363.769 ##################################################################### # Probe ##################################################################### [beacon] serial: /dev/serial/by-id/usb-Beacon_Beacon_RevH_06F0EB985154364134202020FF142909-if00 x_offset: -20 # update with offset from nozzle on your machine y_offset: 0 # update with offset from nozzle on your machine mesh_main_direction: x mesh_runs: 2 [safe_z_home] home_xy_position: 175, 175 # update for your machine z_hop: 3 [bed_mesh] speed: 120 horizontal_move_z: 5 mesh_min: 10, 10 mesh_max: 300, 300 probe_count: 5, 3 mesh_pps: 2, 3 algorithm: bicubic bicubic_tension: 0.2 ## Inductive Probe ## This probe is not used for Z height, only Quad Gantry Leveling ##[probe] #-------------------------------------------------------------------- ## Select the probe port by type: ## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V. #pin: ~!PB7 ## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO. #pin: PG15 ## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper #pin: ~!PC5 #-------------------------------------------------------------------- #x_offset: 0 #y_offset: 25.0 #z_offset: 0 #speed: 10.0 #samples: 3 #samples_result: median #sample_retract_dist: 3.0 #samples_tolerance: 0.006 #samples_tolerance_retries: 3 ##################################################################### # Fan Control ##################################################################### ## Print Cooling Fan - FAN0 #[fan] #pin: PA8 #kick_start_time: 0.5 ## Depending on your fan, you may need to increase this value ## if your fan will not start. Can change cycle_time (increase) ## if your fan is not able to slow down effectively #off_below: 0.10 ## Hotend Fan - FAN1 #[heater_fan hotend_fan] #pin: PE5 #max_power: 1.0 #kick_start_time: 0.5 #heater: extruder #heater_temp: 50.0 ## If you are experiencing back flow, you can reduce fan_speed #fan_speed: 1.0 ## Controller fan - FAN2 [controller_fan controller_fan] pin: PD12 kick_start_time: 0.5 heater: heater_bed ## Exhaust fan - FAN3 #[heater_fan exhaust_fan] #pin: PD13 #max_power: 1.0 #shutdown_speed: 0.0 #kick_start_time: 5.0 #heater: heater_bed #heater_temp: 60 #fan_speed: 1.0 ##################################################################### # LED Control ##################################################################### ## Chamber Lighting - HE2 Connector (Optional) #[output_pin caselight] ##Octopus 1.0 & 1.1, Octopus PRO 1.0 #pin: PB10 ##Octopus PRO 1.1 #pin: PB0 #pwm:true #shutdown_value: 0 #value:1 #cycle_time: 0.01 ##################################################################### # Homing and Gantry Adjustment Routines ##################################################################### [idle_timeout] timeout: 1800 ## Use QUAD_GANTRY_LEVEL to level a gantry. ## Min & Max gantry corners - measure from nozzle at MIN (0,0) and ## MAX (250, 250), (300,300), or (350,350) depending on your printer size ## to respective belt positions #-------------------------------------------------------------------- ## Gantry Corners for 250mm Build ## Uncomment for 250mm build #gantry_corners: # -60,-10 # 310, 320 ## Probe points #points: # 50,25 # 50,175 # 200,175 # 200,25 ## Gantry Corners for 300mm Build ## Uncomment for 300mm build #gantry_corners: # -60,-10 # 360,370 ## Probe points #points: # 50,25 # 50,225 # 250,225 # 250,25 ## Gantry Corners for 350mm Build ## Uncomment for 350mm build #gantry_corners: #-60,-10 #410,420 ## Probe points #points: #50,25 #50,275 #300,275 #300,25 #-------------------------------------------------------------------- #speed: 100 #horizontal_move_z: 10 #retries: 5 #retry_tolerance: 0.0075 #max_adjust: 10 ######################################## # EXP1 / EXP2 (display) pins ######################################## [board_pins] aliases: # EXP1 header EXP1_1=PE8, EXP1_2=PE7, EXP1_3=PE9, EXP1_4=PE10, EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side EXP1_7=PE14, EXP1_8=PE15, EXP1_9=, EXP1_10=<5V>, # EXP2 header EXP2_1=PA6, EXP2_2=PA5, EXP2_3=PB1, EXP2_4=PA4, EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side EXP2_7=PC15, EXP2_8=, EXP2_9=, EXP2_10=<5V> ##################################################################### # Displays ##################################################################### ## Uncomment the display that you have #-------------------------------------------------------------------- ## RepRapDiscount 128x64 Full Graphic Smart Controller #[display] #lcd_type: st7920 #cs_pin: EXP1_4 #sclk_pin: EXP1_5 #sid_pin: EXP1_3 #menu_timeout: 40 #encoder_pins: ^EXP2_5, ^EXP2_3 #click_pin: ^!EXP1_2 #[output_pin beeper] #pin: EXP1_1 #-------------------------------------------------------------------- ## mini12864 LCD Display #[display] #lcd_type: uc1701 #cs_pin: EXP1_3 #a0_pin: EXP1_4 #rst_pin: EXP1_5 #encoder_pins: ^EXP2_5, ^EXP2_3 #click_pin: ^!EXP1_2 #contrast: 63 #spi_software_miso_pin: EXP2_1 #spi_software_mosi_pin: EXP2_6 #spi_software_sclk_pin: EXP2_2 ## To control Neopixel RGB in mini12864 display #[neopixel btt_mini12864] #pin: EXP1_6 #chain_count: 3 #initial_RED: 0.1 #initial_GREEN: 0.5 #initial_BLUE: 0.0 #color_order: RGB ## Set RGB values on boot up for each Neopixel. ## Index 1 = display, Index 2 and 3 = Knob #[delayed_gcode setdisplayneopixel] #initial_duration: 1 #gcode: # SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 # SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 # SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 #-------------------------------------------------------------------- ##################################################################### # Macros ##################################################################### [gcode_macro PARK] gcode: {% set th = printer.toolhead %} G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y//2} Z30 [gcode_macro G32] gcode: SAVE_GCODE_STATE NAME=STATE_G32 G90 G28 QUAD_GANTRY_LEVEL G28 PARK RESTORE_GCODE_STATE NAME=STATE_G32 [gcode_macro PRINT_START] # Use PRINT_START for the slicer starting script - please customise for your slicer of choice gcode: G32 ; home all axes G90 ; absolute positioning G1 Z20 F3000 ; move nozzle away from bed bed_mesh_clear Bed_mesh_calibrate voron_purge line_purge [gcode_macro PRINT_END] # Use PRINT_END for the slicer ending script - please customise for your slicer of choice gcode: # safe anti-stringing move coords {% set th = printer.toolhead %} {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %} {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %} {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %} SAVE_GCODE_STATE NAME=STATE_PRINT_END M400 ; wait for buffer to clear G92 E0 ; zero the extruder G1 E-5.0 F1800 ; retract filament TURN_OFF_HEATERS G90 ; absolute positioning G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear M107 ; turn off fan BED_MESH_CLEAR # The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE # command pair is to restore the printer's coordinate system # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 #*# <---------------------- SAVE_CONFIG ----------------------> #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] #*# model_coef = 1.893197358418992, #*# 2.189688390099554, #*# 0.6793703046731926, #*# 0.07145659600327188, #*# -0.1408335310424842, #*# 0.38702610626257716, #*# 0.3420449523455563, #*# -0.33030962326307656, #*# -0.1595815189762197, #*# 0.10740617142694256 #*# model_domain = 1.9415886291284917e-07,1.9476376064813647e-07 #*# model_range = 0.200000,5.000000 #*# model_temp = 15.070651 #*# model_offset = 0.00000 ``` ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 14, 2024, 9:12pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/8 "2024-10-14T21:12:26Z")
> [@pete1](#): > > ```auto > #*# <---------------------- SAVE_CONFIG ----------------------> > > #*# <---------------------- SAVE_CONFIG ----------------------> > #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. > > ``` change it to ```auto #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated ``` It bit more comments would be quite helpful. ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 14, 2024, 9:43pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/9 "2024-10-14T21:43:28Z")
I am a bit of a loss as to why i try to calibrate beacon and unable to save\_config. Unless i solve this problem I am unable to progress. BTW i am a retired person in their mid 70"s using 3D printing as a way to take up my retirement. I have never asked for help before unless i really need it but have limited experience. # This file contains common pin mappings for the BigTreeTech Octopus V1. # To use this config, the firmware should be compiled for the STM32F446 with a “32KiB bootloader” # Enable “extra low-level configuration options” and select the “12MHz crystal” as clock reference # after running “make”, copy the generated “klipper/out/klipper.bin” file to a # file named “firmware.bin” on an SD card and then restart the OctoPus with that SD card. # See docs/Config\_Reference.md for a description of parameters. ## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config ## \*\*\* THINGS TO CHANGE/CHECK: \*\*\* ## MCU paths [mcu] section ## Thermistor types [extruder] and [heater\_bed] sections - See [Configuration reference - Klipper documentation](https://www.klipper3d.org/Config_Reference.html#common-thermistors) for common thermistor types ## Hotend heater pin [extruder] section ## Z Endstop Switch location [safe\_z\_home] section ## Homing end position [gcode\_macro G32] section ## Z Endstop Switch offset for Z0 [stepper\_z] section ## Stepper Z1 enable pin [stepper\_z1] section ## Probe points [quad\_gantry\_level] section ## Min & Max gantry corner postions [quad\_gantry\_level] section ## PID tune [extruder] and [heater\_bed] sections ## Probe pin [probe] section ## Fine tune E steps [extruder] section [include btt\_ebb-sb2240.cfg] [include mainsail.cfg] #[exclude\_object] #[include Adaptive\_mesh.cfg] #[include KAMP\_Settings.cfg] #[include voron\_purge.cfg] #[include line\_purge.cfg] [mcu] ## Obtain definition by “ls /dev/serial/by-id/\*” then unplug to verify ##-------------------------------------------------------------------- serial: /dev/serial/by-id/usb-Klipper\_stm32f446xx\_060025000E5053424E363620-if00 restart\_method: command ##-------------------------------------------------------------------- [printer] kinematics: corexy max\_velocity: 300 max\_accel: 3000 #Max 4000 max\_z\_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V max\_z\_accel: 350 square\_corner\_velocity: 5.0 ##################################################################### # X/Y Stepper Settings ##################################################################### ## B Stepper - Left ## Connected to MOTOR\_0 ## Endstop connected to DIAG\_0 [stepper\_x] step\_pin: PF13 dir\_pin: PF12 enable\_pin: !PF14 rotation\_distance: 40 microsteps: 32 full\_steps\_per\_rotation:400 #set to 400 for 0.9 degree stepper endstop\_pin: PG6 position\_min: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position\_endstop: 250 #position\_max: 250 ## Uncomment for 300mm build #position\_endstop: 300 #position\_max: 300 ## Uncomment for 350mm build position\_endstop: 350 position\_max: 350 ##-------------------------------------------------------------------- homing\_speed: 25 #Max 100 homing\_retract\_dist: 5 homing\_positive\_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper\_x] uart\_pin: PC4 interpolate: false run\_current: 0.8 sense\_resistor: 0.110 stealthchop\_threshold: 0 ## A Stepper - Right ## Connected to MOTOR\_1 ## Endstop connected to DIAG\_1 [stepper\_y] step\_pin: PG0 dir\_pin: PG1 enable\_pin: !PF15 rotation\_distance: 40 microsteps: 32 full\_steps\_per\_rotation:400 #set to 400 for 0.9 degree stepper endstop\_pin: PG9 position\_min: 0 ##-------------------------------------------------------------------- ## Uncomment for 250mm build #position\_endstop: 250 #position\_max: 250 ## Uncomment for 300mm build #position\_endstop: 300 #position\_max: 300 ## Uncomment for 350mm build position\_endstop: 350 position\_max: 350 ##-------------------------------------------------------------------- homing\_speed: 25 #Max 100 homing\_retract\_dist: 5 homing\_positive\_dir: true ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper\_y] uart\_pin: PD11 interpolate: false run\_current: 0.8 sense\_resistor: 0.110 stealthchop\_threshold: 0 ##################################################################### # Z Stepper Settings ##################################################################### ## Z0 Stepper - Front Left ## Connected to MOTOR\_2 ## Endstop connected to DIAG\_2 [stepper\_z] step\_pin: PF11 dir\_pin: PG3 enable\_pin: !PG5 rotation\_distance: 40 gear\_ratio: 80:16 microsteps: 32 endstop\_pin: probe: z\_virtual\_endstop ## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) ## (+) value = endstop above Z0, (-) value = endstop below ## Increasing position\_endstop brings nozzle closer to the bed ## After you run Z\_ENDSTOP\_CALIBRATE, position\_endstop will be stored at the very end of your config #position\_endstop: 0 ##-------------------------------------------------------------------- ## Uncomment below for 250mm build #position\_max: 210 ## Uncomment below for 300mm build #position\_max: 260 ## Uncomment below for 350mm build position\_max: 350 ##-------------------------------------------------------------------- position\_min: -5 homing\_speed: 8 second\_homing\_speed: 3 homing\_retract\_dist: 0 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper\_z] uart\_pin: PC6 interpolate: false run\_current: 0.8 sense\_resistor: 0.110 stealthchop\_threshold: 0 ## Z1 Stepper - Rear Left ## Connected to MOTOR\_3 [stepper\_z1] step\_pin: PG4 dir\_pin: !PC1 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 enable\_pin: !PA0 ## Octopus PRO 1.1 #enable\_pin: !PA2 rotation\_distance: 40 gear\_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper\_z1] uart\_pin: PC7 interpolate: false run\_current: 0.8 sense\_resistor: 0.110 stealthchop\_threshold: 0 ## Z2 Stepper - Rear Right ## Connected to MOTOR\_4 [stepper\_z2] step\_pin: PF9 dir\_pin: PF10 enable\_pin: !PG2 rotation\_distance: 40 gear\_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper\_z2] uart\_pin: PF2 interpolate: false run\_current: 0.8 sense\_resistor: 0.110 stealthchop\_threshold: 0 ## Z3 Stepper - Front Right ## Connected to MOTOR\_5 [stepper\_z3] step\_pin: PC13 dir\_pin: !PF0 enable\_pin: !PF1 rotation\_distance: 40 gear\_ratio: 80:16 microsteps: 32 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper\_z3] uart\_pin: PE4 interpolate: false run\_current: 0.8 sense\_resistor: 0.110 stealthchop\_threshold: 0 ##################################################################### # Extruder ##################################################################### ## Connected to MOTOR\_6 ## Heater - HE0 ## Thermistor - T0 #[extruder] #step\_pin: PE2 #dir\_pin: PE3 #enable\_pin: !PD4 ## Update value below when you perform extruder calibration ## If you ask for 100mm of filament, but in reality it is 98mm: ## rotation\_distance = \ \* \ / 100 ## 22.6789511 is a good starting point #rotation\_distance: 22.6789511 #Bondtech 5mm Drive Gears ## Update Gear Ratio depending on your Extruder Type ## Use 50:10 for Stealthburner/Clockwork 2 ## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) ## Use 80:20 for M4, M3.1 #gear\_ratio: 50:10 #microsteps: 32 #full\_steps\_per\_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree #nozzle\_diameter: 0.400 #filament\_diameter: 1.75 ## Octopus 1.0 & 1.1. Octopus PRO 1.0 #heater\_pin: PA2 ## Octopus PRO 1.1 #heater\_pin: PA0 ## Check what thermistor type you have. See [Configuration reference - Klipper documentation](https://www.klipper3d.org/Config_Reference.html#common-thermistors) for common thermistor types. ## Use “Generic 3950” for NTC 100k 3950 thermistors #sensor\_type: Generic 3950 #sensor\_pin: PF4 #min\_temp: -100 #max\_temp: 270 #max\_power: 1.0 #min\_extrude\_temp: 170 #control = pid #pid\_kp = 26.213 #pid\_ki = 1.304 #pid\_kd = 131.721 ## Try to keep pressure\_advance below 1.0 #pressure\_advance: 0.05 ## Default is 0.040, leave stock #pressure\_advance\_smooth\_time: 0.040 ## E0 on MOTOR6 ## Make sure to update below for your relevant driver (2208 or 2209) #[tmc2209 extruder] #uart\_pin: PE1 #interpolate: false #run\_current: 0.5 #sense\_resistor: 0.110 #stealthchop\_threshold: 0 ##################################################################### # Bed Heater ##################################################################### ## SSR Pin - HE1 ## Thermistor - TB [heater\_bed] ## Uncomment the following line if using the default SSR wiring from the docs site heater\_pin: PA3 ## Other wiring guides may use BED\_OUT to control the SSR. Uncomment the following line for those cases #heater\_pin: PA1 ## Check what thermistor type you have. See [Configuration reference - Klipper documentation](https://www.klipper3d.org/Config_Reference.html#common-thermistors) for common thermistor types. ## Use “Generic 3950” for Keenovo heaters sensor\_type: Generic 3950 sensor\_pin: PF3 ## Adjust max\_power so it doesn’t exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink. ## The formula is “4 / (Wattage\_of\_bed\_heater / Mains\_voltage) = max\_power” ## If max\_power is greater than 1.0, use 1.0 max\_power: 0.6 min\_temp: 0 max\_temp: 120 control: pid pid\_kp: 58.437 pid\_ki: 2.347 pid\_kd: 363.769 ##################################################################### # Probe ##################################################################### [beacon] serial: /dev/serial/by-id/usb-Beacon\_Beacon\_RevH\_06F0EB985154364134202020FF142909-if00 x\_offset: -20 # update with offset from nozzle on your machine y\_offset: 0 # update with offset from nozzle on your machine mesh\_main\_direction: x mesh\_runs: 2 [safe\_z\_home] home\_xy\_position: 175, 175 # update for your machine z\_hop: 3 [bed\_mesh] speed: 120 horizontal\_move\_z: 5 mesh\_min: 10, 10 mesh\_max: 300, 300 probe\_count: 5, 3 mesh\_pps: 2, 3 algorithm: bicubic bicubic\_tension: 0.2 ## Inductive Probe ## This probe is not used for Z height, only Quad Gantry Leveling ##[probe] #-------------------------------------------------------------------- ## Select the probe port by type: ## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V. #pin: ~!PB7 ## For the DIAG\_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO. #pin: PG15 ## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper #pin: ~!PC5 #-------------------------------------------------------------------- #x\_offset: 0 #y\_offset: 25.0 #z\_offset: 0 #speed: 10.0 #samples: 3 #samples\_result: median #sample\_retract\_dist: 3.0 #samples\_tolerance: 0.006 #samples\_tolerance\_retries: 3 ##################################################################### # Fan Control ##################################################################### ## Print Cooling Fan - FAN0 #[fan] #pin: PA8 #kick\_start\_time: 0.5 ## Depending on your fan, you may need to increase this value ## if your fan will not start. Can change cycle\_time (increase) ## if your fan is not able to slow down effectively #off\_below: 0.10 ## Hotend Fan - FAN1 #[heater\_fan hotend\_fan] #pin: PE5 #max\_power: 1.0 #kick\_start\_time: 0.5 #heater: extruder #heater\_temp: 50.0 ## If you are experiencing back flow, you can reduce fan\_speed #fan\_speed: 1.0 ## Controller fan - FAN2 [controller\_fan controller\_fan] pin: PD12 kick\_start\_time: 0.5 heater: heater\_bed ## Exhaust fan - FAN3 #[heater\_fan exhaust\_fan] #pin: PD13 #max\_power: 1.0 #shutdown\_speed: 0.0 #kick\_start\_time: 5.0 #heater: heater\_bed #heater\_temp: 60 #fan\_speed: 1.0 ##################################################################### # LED Control ##################################################################### ## Chamber Lighting - HE2 Connector (Optional) #[output\_pin caselight] ##Octopus 1.0 & 1.1, Octopus PRO 1.0 #pin: PB10 ##Octopus PRO 1.1 #pin: PB0 #pwm:true #shutdown\_value: 0 #value:1 #cycle\_time: 0.01 ##################################################################### # Homing and Gantry Adjustment Routines ##################################################################### [idle\_timeout] timeout: 1800 ## Use QUAD\_GANTRY\_LEVEL to level a gantry. ## Min & Max gantry corners - measure from nozzle at MIN (0,0) and ## MAX (250, 250), (300,300), or (350,350) depending on your printer size ## to respective belt positions #-------------------------------------------------------------------- ## Gantry Corners for 250mm Build ## Uncomment for 250mm build #gantry\_corners: # -60,-10 # 310, 320 ## Probe points #points: # 50,25 # 50,175 # 200,175 # 200,25 ## Gantry Corners for 300mm Build ## Uncomment for 300mm build #gantry\_corners: # -60,-10 # 360,370 ## Probe points #points: # 50,25 # 50,225 # 250,225 # 250,25 ## Gantry Corners for 350mm Build ## Uncomment for 350mm build #gantry\_corners: #-60,-10 #410,420 ## Probe points #points: #50,25 #50,275 #300,275 #300,25 #-------------------------------------------------------------------- #speed: 100 #horizontal\_move\_z: 10 #retries: 5 #retry\_tolerance: 0.0075 #max\_adjust: 10 ######################################## # EXP1 / EXP2 (display) pins ######################################## [board\_pins] aliases: # EXP1 header EXP1\_1=PE8, EXP1\_2=PE7, EXP1\_3=PE9, EXP1\_4=PE10, EXP1\_5=PE12, EXP1\_6=PE13, # Slot in the socket on this side EXP1\_7=PE14, EXP1\_8=PE15, EXP1\_9=, EXP1\_10=\<5V\>, ``` # EXP2 header EXP2_1=PA6, EXP2_2=PA5, EXP2_3=PB1, EXP2_4=PA4, EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side EXP2_7=PC15, EXP2_8=, EXP2_9=, EXP2_10=<5V> ``` ##################################################################### # Displays ##################################################################### ## Uncomment the display that you have #-------------------------------------------------------------------- ## RepRapDiscount 128x64 Full Graphic Smart Controller #[display] #lcd\_type: st7920 #cs\_pin: EXP1\_4 #sclk\_pin: EXP1\_5 #sid\_pin: EXP1\_3 #menu\_timeout: 40 #encoder\_pins: ^EXP2\_5, ^EXP2\_3 #click\_pin: ^!EXP1\_2 #[output\_pin beeper] #pin: EXP1\_1 #-------------------------------------------------------------------- ## mini12864 LCD Display #[display] #lcd\_type: uc1701 #cs\_pin: EXP1\_3 #a0\_pin: EXP1\_4 #rst\_pin: EXP1\_5 #encoder\_pins: ^EXP2\_5, ^EXP2\_3 #click\_pin: ^!EXP1\_2 #contrast: 63 #spi\_software\_miso\_pin: EXP2\_1 #spi\_software\_mosi\_pin: EXP2\_6 #spi\_software\_sclk\_pin: EXP2\_2 ## To control Neopixel RGB in mini12864 display #[neopixel btt\_mini12864] #pin: EXP1\_6 #chain\_count: 3 #initial\_RED: 0.1 #initial\_GREEN: 0.5 #initial\_BLUE: 0.0 #color\_order: RGB ## Set RGB values on boot up for each Neopixel. ## Index 1 = display, Index 2 and 3 = Knob #[delayed\_gcode setdisplayneopixel] #initial\_duration: 1 #gcode: # SET\_LED LED=btt\_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 # SET\_LED LED=btt\_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 # SET\_LED LED=btt\_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 #-------------------------------------------------------------------- ##################################################################### # Macros ##################################################################### [gcode\_macro PARK] gcode: {% set th = printer.toolhead %} G0 X{th.axis\_maximum.x//2} Y{th.axis\_maximum.y//2} Z30 [gcode\_macro G32] gcode: SAVE\_GCODE\_STATE NAME=STATE\_G32 G90 G28 QUAD\_GANTRY\_LEVEL G28 PARK RESTORE\_GCODE\_STATE NAME=STATE\_G32 [gcode\_macro PRINT\_START] # Use PRINT\_START for the slicer starting script - please customise for your slicer of choice gcode: G32 ; home all axes G90 ; absolute positioning G1 Z20 F3000 ; move nozzle away from bed bed\_mesh\_clear Bed\_mesh\_calibrate voron\_purge line\_purge [gcode\_macro PRINT\_END] # Use PRINT\_END for the slicer ending script - please customise for your slicer of choice gcode: # safe anti-stringing move coords {% set th = printer.toolhead %} {% set x\_safe = th.position.x + 20 \* (1 if th.axis\_maximum.x - th.position.x \> 20 else -1) %} {% set y\_safe = th.position.y + 20 \* (1 if th.axis\_maximum.y - th.position.y \> 20 else -1) %} {% set z\_safe = [th.position.z + 2, th.axis\_maximum.z]|min %} ``` SAVE_GCODE_STATE NAME=STATE_PRINT_END M400 ; wait for buffer to clear G92 E0 ; zero the extruder G1 E-5.0 F1800 ; retract filament TURN_OFF_HEATERS G90 ; absolute positioning G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear M107 ; turn off fan BED_MESH_CLEAR # The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE # command pair is to restore the printer's coordinate system # and speed settings since the commands above change them. # However, to prevent any accidental, unintentional toolhead # moves when restoring the state, explicitly set MOVE=0. RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 ``` #_# \<---------------------- SAVE\_CONFIG ----------------------\> #_# [beacon model default] #_# model\_coef = 1.893197358418992, #_# 2.189688390099554, #_# 0.6793703046731926, #_# 0.07145659600327188, #_# -0.1408335310424842, #_# 0.38702610626257716, #_# 0.3420449523455563, #_# -0.33030962326307656, #_# -0.1595815189762197, #_# 0.10740617142694256 #_# model\_domain = 1.9415886291284917e-07,1.9476376064813647e-07 #_# model\_range = 0.200000,5.000000 #_# model\_temp = 15.070651 #_# model\_offset = 0.00000 ```auto ``` ---
**Author:** ![mykepredko](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/mykepredko/32/2085_2.png) [@mykepredko](https://klipper.discourse.group/u/mykepredko)\ **Post date:** [October 15, 2024, 12:22am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/10 "2024-10-15T00:22:20Z")
Please follow what @EddyMI3D instructed you for posting your `printer.cfg`: > [@After beacon calibrate and save config klipper unable to recognise default](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/4): > > Please also the printer.cfg as a file! and not Copy & Paste. At least use the Preformatted Text feature of the forum editor. [Format] The way you did it, the data is not usable at all. BTW: You have 12 (!) config blocks. That can not work. The big dump isn’t easy to follow. ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 15, 2024, 12:47am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/11 "2024-10-15T00:47:01Z")
[printer (2).zip](https://klipper.discourse.group/uploads/short-url/jMcSKRN7qFoHvd21vmMpdYqBioe.zip) (5.7 KB) ---
**Author:** ![mykepredko](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/mykepredko/32/2085_2.png) [@mykepredko](https://klipper.discourse.group/u/mykepredko)\ **Post date:** [October 15, 2024, 1:40am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/12 "2024-10-15T01:40:48Z")
Just doing a quick look at the file (thank you - but you don’t need to .zip it) - and I see that you still haven’t make the changes that @EddyMI3D suggested to you above. Please Change the first two lines of your `printer.cfg` from: ```auto #*# <---------------------- SAVE_CONFIG ----------------------> #*# [beacon model default] ``` to ```auto #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [beacon model default] ``` That should resolve your problem and allow you to `SAVE_CONFIG`. ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 15, 2024, 2:40am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/13 "2024-10-15T02:40:35Z")
Thanks for that. I changed all as suggested and after beacon\_calibrated I save\_config. When I g28 it comes up with the message: No Beacon model loaded. ---
**Author:** ![mykepredko](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/mykepredko/32/2085_2.png) [@mykepredko](https://klipper.discourse.group/u/mykepredko)\ **Post date:** [October 15, 2024, 3:35am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/14 "2024-10-15T03:35:26Z")
Did you follow the instructions here: [https://docs.beacon3d.com/quickstart/#3-install-beacon-klipper-module](https://docs.beacon3d.com/quickstart/#3-install-beacon-klipper-module) ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 15, 2024, 3:48am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/15 "2024-10-15T03:48:59Z")
Yes all done as per beacons instructions to the letter. For some reason klipper is not accepting beacon. ---
**Author:** ![mykepredko](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/mykepredko/32/2085_2.png) [@mykepredko](https://klipper.discourse.group/u/mykepredko)\ **Post date:** [October 15, 2024, 5:20am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/16 "2024-10-15T05:20:24Z")
Can you post your latest `'klippy.log' and `moonraker.cfg`? ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 15, 2024, 6:29am UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/17 "2024-10-15T06:29:06Z")
Hello @pete1 ! **Pleas do this:** > [@EddyMI3D](#): > > Please also the printer.cfg as a file! and not Copy & Paste. > > At least use the `Preformatted Text` feature of the forum editor. > > ![Format](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/6/643ab9def96b03089cfb0c194628129fcc96b3f8.png) > > The way you did it, the data is not usable at all. > > BTW: You have 12 (!) config blocks. That can not work. ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 15, 2024, 8:37pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/18 "2024-10-15T20:37:55Z")
[klippy (21).log](https://klipper.discourse.group/uploads/short-url/jeHuzEfLbtkvd9VHpyvh0Sw4ur1.log) (73.5 KB) [moonraker.conf](https://klipper.discourse.group/uploads/short-url/iDd0kVkF7cpIms65JvbHpQNh8oE.conf) (2.7 KB) ---
**Author:** ![pete1](https://avatars.discourse-cdn.com/v4/letter/p/67e7ee/32.png) [@pete1](https://klipper.discourse.group/u/pete1)\ **Post date:** [October 15, 2024, 8:39pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/19 "2024-10-15T20:39:32Z")
[printer (3).cfg](https://klipper.discourse.group/uploads/short-url/r7a42YmR4YXrEiekNSsc0noBaVQ.cfg) (18.2 KB) ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 15, 2024, 8:46pm UTC](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360/20 "2024-10-15T20:46:19Z")
There are still two config blocks. You may delete them both. Klipper should build a new config block. [Next page](https://klipper.discourse.group/t/after-beacon-calibrate-and-save-config-klipper-unable-to-recognise-default/19360.md?page=2)