# Bed\_mesh\_calibrate move out of range

**URL:** <https://klipper.discourse.group/t/bed-mesh-calibrate-move-out-of-range/19072>\
**Category:** General Discussion\
**Created:** [September 28, 2024, 5:54pm UTC](https://klipper.discourse.group/t/bed-mesh-calibrate-move-out-of-range/19072 "2024-09-28T17:54:50Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Batwing99991](https://avatars.discourse-cdn.com/v4/letter/b/839c29/32.png) [@Batwing99991](https://klipper.discourse.group/u/Batwing99991)\
**Post date:** [September 28, 2024, 5:54pm UTC](https://klipper.discourse.group/t/bed-mesh-calibrate-move-out-of-range/19072/1 "2024-09-28T17:54:50Z")

</div>

### Basic Information:

Printer Model: Ender 3v2  
 MCU / Printerboard: Whatever is default in the Ender 3v2, I’m not sure  
 Host / SBC: Raspberry Pi 3B+  
 klippy.log  
[klippy.log](https://klipper.discourse.group/uploads/short-url/ijl91tMIE7uNWPrxMpLezTB7MXx.log) (54.6 KB)  
 printer.cfg  
[printer.cfg](https://klipper.discourse.group/uploads/short-url/qgzTIvum3MxcFs25FhvqgQ9x4q4.cfg) (8.4 KB)

### Describe your issue:

Whenever I try to configure the bed mesh, it gives me an error on probe 6 I believe. The error is “Move out of range: 60.000 235.000 5.000 [0.000]”  
I looked in my printer.cfg and there is no reference to 235 anywhere.

Edit: did some more research, I fixed it. Forgot to account for the bltouch offset. Solution was to subtract 190 (mesh\_max) from the error, which gave me 45, then I did 220 (set bed size) - 45, which gave me the number i needed for the mesh\_max.

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [September 28, 2024, 7:00pm UTC](https://klipper.discourse.group/t/bed-mesh-calibrate-move-out-of-range/19072/2 "2024-09-28T19:00:06Z")

</div>

Hello @Batwing99991 !

> [@Batwing99991](#):
>
> The error is “Move out of range: 60.000 235.000 5.000 [0.000]”

Obviously!

```auto
[stepper_y]
step_pin = PB8
dir_pin = PB7
enable_pin = !PC3
microsteps = 16
rotation_distance = 40
endstop_pin = ^PA6
position_endstop = 0
position_max = 220 # <---
homing_speed = 50

```

Position\_max is 220 mm.

```auto
[bltouch]
sensor_pin = ^PB1
control_pin = PB0
x_offset = -30
y_offset = -45 # <----
z_offset = 1.62

```

The BLtouch is 45 mm in front of the nozzle (Top view)

```auto
[bed_mesh]
speed = 120
horizontal_move_z = 5
mesh_min = 30,7
mesh_max = 179,190 # <----
probe_count = 3,3
algorithm = bicubic
fade_start = 1
fade_end = 10
fade_target = 0

```

You want to reach 190 on the Y-axes with the BLtouch.

190 + 45 = 235 → The nozzle can’t reach that point

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\
**Post date:** [October 29, 2024, 6:33am UTC](https://klipper.discourse.group/t/bed-mesh-calibrate-move-out-of-range/19072/4 "2024-10-29T06:33:31Z")

</div>

Closed on October 29, 2024, 6:33am UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.