# Been a while, so bare with me

**URL:** <https://klipper.discourse.group/t/been-a-while-so-bare-with-me/23105>\
**Category:** General Discussion\
**Created:** [April 21, 2025, 3:45pm UTC](https://klipper.discourse.group/t/been-a-while-so-bare-with-me/23105 "2025-04-21T15:45:45Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Sgt\_Stoll](https://avatars.discourse-cdn.com/v4/letter/s/3be4f8/32.png) [@Sgt\_Stoll](https://klipper.discourse.group/u/Sgt_Stoll)\
**Post date:** [April 21, 2025, 3:45pm UTC](https://klipper.discourse.group/t/been-a-while-so-bare-with-me/23105/1 "2025-04-21T15:45:45Z")

</div>

### Basic Information:

Printer Model: CR10 ish  
 MCU / Printerboard: Bigtreetech skr mini e3 v3.0  
 Host / SBC  
[safe\_z\_home]  
home\_xy\_position: 150,150 # Change coordinates to the center of your print bed  
speed: 50  
z\_hop: 10 # Move up 10mm  
z\_hop\_speed: 5

[bed\_mesh]  
speed: 120  
horizontal\_move\_z: 10  
mesh\_min: 7, 9  
mesh\_max: 251, 256  
probe\_count: 5,5  
mesh\_pps: 2,2  
fade\_start: 1  
fade\_end: 10  
fade\_target: 0

[stepper\_z]  
step\_pin: PB0  
dir\_pin: PC5  
enable\_pin: !PB1  
microsteps: 16  
rotation\_distance: 8

# endstop\_pin: ^PC2

# position\_endstop: 0.0

endstop\_pin: probe:z\_virtual\_endstop  
position\_max: 400  
position\_min: -2

[stepper\_x]  
step\_pin: PB13  
dir\_pin: !PB12  
enable\_pin: !PB14  
microsteps: 16  
rotation\_distance: 40  
endstop\_pin: ^PC0  
position\_endstop: 0  
position\_max: 284  
homing\_speed: 50

[tmc2209 stepper\_x]  
uart\_pin: PC11  
tx\_pin: PC10  
uart\_address: 0  
run\_current: 0.580  
hold\_current: 0.500  
stealthchop\_threshold: 999999

[stepper\_y]  
step\_pin: PB10  
dir\_pin: !PB2  
enable\_pin: !PB11  
microsteps: 16  
rotation\_distance: 40  
endstop\_pin: ^PC1  
position\_endstop: 0  
position\_max: 297  
homing\_speed: 50

_Fill out above information and_ **_in all cases attach your_ `klippy.log` _file_** (use zip to compress it, if too big). _Pasting your_ `printer.cfg` _is **not** needed_  
_ **Be sure to check our “Knowledge Base” Category first. Most relevant items, e.g. error messages, are covered there** _

### Describe your issue:

It’s been about a year since I’ve printed anything and with a new computer I’m trying to get everything set back up. I stopped printing last year because of some frustrations but after a year of mediation I think I know what my original issue was caused by (i was trying to run a duel axis and gave me nothing but head aches).

Well my question is when I home it it goes to the middle but when I start a print it does not start in the middle. I feel like I’m relearning everything (its a bit easier the second time) but not sure were I should start trying to figure it out. I was originally thinking it was something to do with my end stops but the fact it homes correctly confuses me. This is a customer printer I built off a CR10 frame but have replaced everything on it, the board, the hot end, the steppers, and even the bed. It’s still 400x400 just upgraded the heating.

 ![image](https://global.discourse-cdn.com/free1/uploads/klipper/original/3X/5/6/5699c9ac3496eb8f87df7789baebb952c81c659d.jpeg)

…

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [April 21, 2025, 4:32pm UTC](https://klipper.discourse.group/t/been-a-while-so-bare-with-me/23105/2 "2025-04-21T16:32:23Z")

</div>

Hello @Sgt_Stoll !

> [@Sgt\_Stoll](#):
>
> _Fill out above information and_ **_in all cases attach your_ `klippy.log` _file_** (use zip to compress it, if too big). _Pasting your_ `printer.cfg` _is **not** needed_  
> _ **Be sure to check our “Knowledge Base” Category first. Most relevant items, e.g. error messages, are covered there** _

Please attach it to your next post.

Also, as mentioned above, posting the `printer.cfg` is not needed.  
When you post code, please use the Preformatted Text feature of the forum editor.

In all: [How-To Ask for Help](https://klipper.discourse.group/t/how-to-ask-for-help/6327/1)

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\
**Post date:** [June 20, 2025, 4:32pm UTC](https://klipper.discourse.group/t/been-a-while-so-bare-with-me/23105/3 "2025-06-20T16:32:50Z")

</div>

This topic was automatically closed 60 days after the last reply. New replies are no longer allowed.