# Cr Touch in Klipper?

**URL:** <https://klipper.discourse.group/t/cr-touch-in-klipper/3334>\
**Category:** General Discussion\
**Created:** [July 2, 2022, 3:54am UTC](https://klipper.discourse.group/t/cr-touch-in-klipper/3334 "2022-07-02T03:54:09Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Peurif](https://avatars.discourse-cdn.com/v4/letter/p/c57346/32.png) [@Peurif](https://klipper.discourse.group/u/Peurif)\
**Post date:** [July 2, 2022, 3:54am UTC](https://klipper.discourse.group/t/cr-touch-in-klipper/3334/1 "2022-07-02T03:54:09Z")

</div>

Hi,

I have a BlTouch(Clone) installed on my printer, such as Zprobe. And I want to try a Cr Touch… but I can’t find any detailed guide on how to install it. From what I have seen they are very similar, it is easy for the wiring to work the same for me, but I am not sure…

Can someone give me a link to a resource that explains how to install Cr Touch (hardware and klipper configuration)?

Thank you

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [July 2, 2022, 5:48am UTC](https://klipper.discourse.group/t/cr-touch-in-klipper/3334/2 "2022-07-02T05:48:53Z")

</div>

Maybe this thread can help:

> [@CR-Touch always triggered](https://klipper.discourse.group/t/cr-touch-always-triggered/3028):
>
> Hi, I have been printing using marlin for a couple of months now with no major issues. I figured I would give Klipper a try to further optimize my prints. When I got to the part of the [guide](https://www.klipper3d.org/BLTouch.html) regarding bltouch I began experiencing errors The Issue: When I type query\_probe into the terminal klipper invariably returns : // probe: TRIGGERED Raising, lowering, and resetting has no effect on this output. Additionally this error is thrown after firmware restart. $ FIRMWARE\_RESTART // Failed to ve…

---

<div class="post-metadata">

**Author:** ![algore](https://avatars.discourse-cdn.com/v4/letter/a/7ab992/32.png) [@algore](https://klipper.discourse.group/u/algore)\
**Post date:** [July 9, 2022, 3:26am UTC](https://klipper.discourse.group/t/cr-touch-in-klipper/3334/3 "2022-07-09T03:26:01Z")

</div>

Here is what I use in my printer.cfg for Ender 3 with cr touch, it works fine so maybe this could help you.

```auto
[bltouch]
sensor pin: ^PB1 #4.2.2 creatality board
control_pin: PBO #4.2.2 creatality board
x offset: -48 # Satsana Fan Duct Remix for Micro Swiss Direct Drive
y offset: -8.3 # CR Touch offset
#z offset: 1 # will update
pin_up_touch_mode_reports _triggered: False
stow on each sample: False
probe with touch mode: True

```

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [September 19, 2025, 5:00pm UTC](https://klipper.discourse.group/t/cr-touch-in-klipper/3334/4 "2025-09-19T17:00:58Z")

</div>