# Eddy Coil USB Adapter

**URL:** <https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382>\
**Category:** General Discussion\
**Created:** [March 6, 2025, 6:54pm UTC](https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382 "2025-03-06T18:54:12Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Frhulst](https://avatars.discourse-cdn.com/v4/letter/f/58956e/32.png) [@Frhulst](https://klipper.discourse.group/u/Frhulst)\
**Post date:** [March 6, 2025, 6:54pm UTC](https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382/1 "2025-03-06T18:54:12Z")

</div>

### Basic Information:

Printer Model: Neptune 4 pro  
 MCU / Printerboard: V1.1  
 Host / SBC OpenNeptune4  
[klippy(1).log](https://klipper.discourse.group/uploads/short-url/gAJnVH2vb50cw8yzoXBJ9TNLixh.log) (801.1 KB)

So I recently bought the eddy coil as an upgrade, but the coil being much cheaper for some reason (literary 1/2 of the non-coil one)  
And my plan was to use like a Raspberry pi pico and a level shifter to adapt it into the usb version  
Today i got my order so i threw up some code using some elbow grease and chatgpt  
So the code talks to it over i2c and converts the raw data over usb serial, but i get a zero and nothing i do (physically) changes it  
So i probably need some initialization but the official docs aren’t very helpful

heres the code:

> <https://pastebin.com/Aw5xpCKQ>

and heres the output:  
Sensor Data: 0  
and this repeat every poll  
Thanks in advance

---

<div class="post-metadata">

**Author:** ![Arksine](https://avatars.discourse-cdn.com/v4/letter/a/ce7236/32.png) [@Arksine](https://klipper.discourse.group/u/Arksine)\
**Post date:** [March 6, 2025, 7:08pm UTC](https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382/2 "2025-03-06T19:08:07Z")

</div>

You shouldn’t need to write your own code for this. Wire the i2c pins to your pico flashed with Klipper, then configure the MCU and the [probe](https://www.klipper3d.org/Config_Reference.html#probe_eddy_current).

---

<div class="post-metadata">

**Author:** ![Frhulst](https://avatars.discourse-cdn.com/v4/letter/f/58956e/32.png) [@Frhulst](https://klipper.discourse.group/u/Frhulst)\
**Post date:** [March 6, 2025, 7:42pm UTC](https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382/3 "2025-03-06T19:42:15Z")

</div>

ok, i flashed it with klipper firmware but im struggling with some of the config options, do you have a more beginner friendly guide for that

---

<div class="post-metadata">

**Author:** ![Arksine](https://avatars.discourse-cdn.com/v4/letter/a/ce7236/32.png) [@Arksine](https://klipper.discourse.group/u/Arksine)\
**Post date:** [March 7, 2025, 10:53am UTC](https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382/4 "2025-03-07T10:53:06Z")

</div>

The best I can do is provide BTT’s guide:

> **[GitHub - bigtreetech/Eddy](https://github.com/bigtreetech/Eddy/tree/master)**
>
> master

It appears much of their sample configuration applies to the USB version. Two things to keep in mind:

1. The “coil” version doesn’t have a thermistor, so the `[temperature_sensor]` and `[temperature_probe]` sections need to be omitted.

2. As the sample configs state, you need to verify your `i2c_bus` option in `[probe_eddy_current]`, as it depends on the pins you are using on your Pico. The best way to do this right now is to refer to Klipper’s source.

> <https://github.com/Klipper3d/klipper/blob/75a10bfcafc0655e36e5ecf01c3f2033a14ef2c7/src/rp2040/i2c.c#L36-L50>

In these definitions the bus name is in the first parameter, ie: `BUS_PINS_{bus name}`. The second parameter defines the pins, `{sda_pin, scl_pin}`.

You can cross reference the pico’s [pinout](https://pico.pinout.xyz/) to verify. So for example, bus `i2c0a` is on pin `GP0` and `GP1`.

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\
**Post date:** [April 6, 2025, 8:54pm UTC](https://klipper.discourse.group/t/eddy-coil-usb-adapter/22382/5 "2025-04-06T20:54:02Z")

</div>

Closed on April 6, 2025, 8:54pm UTC

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.
