# Ender 5 pro problem x homing **URL:** \ **Category:** General Discussion\ **Created:** [December 11, 2022, 10:03am UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321 "2022-12-11T10:03:23Z")\ **Posts on this page:** 12\ **Page:** 1
**Author:** ![Pbonamy](https://avatars.discourse-cdn.com/v4/letter/p/ea666f/32.png) [@Pbonamy](https://klipper.discourse.group/u/Pbonamy)\ **Post date:** [December 11, 2022, 10:03am UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/1 "2022-12-11T10:03:23Z")
### Basic Information: Printer Model: Ender 5 pro MCU / Printerboard: bigtreetech skr mini e3 v2 `klippy.log` ### Describe your issue: New from klipper, i used it with octoklipper via octoprint. Verify all until stepper motor, I notice a different sound for the x, y and z OK a little bit noisy than my marlin config. G 28 y and G 28 z homing OK but G28 x big noise and printer shut down. I revert to marlin to see a driver or motor problem, all is OK. Can you help me? ![x_homing_problem](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/e/e0eb6840be3a29249054c8274aad7925a8b9cdbc.gif) Regards Pat [klippy.log](https://klipper.discourse.group/uploads/short-url/r8QrtB7dhbIbG1sBO0w0okaA47p.log) (45.8 KB) ---
**Author:** ![jrobbom5](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/jrobbom5/32/3187_2.png) [@jrobbom5](https://klipper.discourse.group/u/jrobbom5)\ **Post date:** [December 11, 2022, 10:13am UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/2 "2022-12-11T10:13:47Z")
You need to post your klippy.log file, without it it’s very hard to diagnose anything. ---
**Author:** ![Pbonamy](https://avatars.discourse-cdn.com/v4/letter/p/ea666f/32.png) [@Pbonamy](https://klipper.discourse.group/u/Pbonamy)\ **Post date:** [December 11, 2022, 10:41am UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/3 "2022-12-11T10:41:45Z")
I upload it, where it is? I reupload it. Thanks for helping. [klippy.log](https://klipper.discourse.group/uploads/short-url/r8QrtB7dhbIbG1sBO0w0okaA47p.log) (45.8 KB) ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [December 11, 2022, 10:57am UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/4 "2022-12-11T10:57:35Z")
Follow [verify-endstops](https://www.klipper3d.org/Config_checks.html#verify-endstops) and make sure your endstop is working as intended. ---
**Author:** ![jrobbom5](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/jrobbom5/32/3187_2.png) [@jrobbom5](https://klipper.discourse.group/u/jrobbom5)\ **Post date:** [December 11, 2022, 11:36am UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/5 "2022-12-11T11:36:43Z")
I notice that the kinematics are set to corexy, but to my understanding, the ender5 pro is a cartesian printer, not corexy. Have you modified the printer to be corexy? Where did you get the config file from? ---
**Author:** ![Pbonamy](https://avatars.discourse-cdn.com/v4/letter/p/ea666f/32.png) [@Pbonamy](https://klipper.discourse.group/u/Pbonamy)\ **Post date:** [December 11, 2022, 1:51pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/6 "2022-12-11T13:51:37Z")
Vérification is OK. Thanks for helping. ---
**Author:** ![Pbonamy](https://avatars.discourse-cdn.com/v4/letter/p/ea666f/32.png) [@Pbonamy](https://klipper.discourse.group/u/Pbonamy)\ **Post date:** [December 11, 2022, 2:00pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/7 "2022-12-11T14:00:20Z")
CoreXY a Cartesian printer I will try to change. I take the file from klipper config file for skr mini e3 v2 and I adapt for my printer. Thanks fore helping ---
**Author:** ![jrobbom5](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/jrobbom5/32/3187_2.png) [@jrobbom5](https://klipper.discourse.group/u/jrobbom5)\ **Post date:** [December 11, 2022, 2:27pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/8 "2022-12-11T14:27:30Z")
Corexy and Cartesian are two very different kinematic systems, they are not compatible. If you take a look in the ~/klipper/config directory, there is a sample config file specifically for the Ender 5 Pro. Good luck! ---
**Author:** ![Pbonamy](https://avatars.discourse-cdn.com/v4/letter/p/ea666f/32.png) [@Pbonamy](https://klipper.discourse.group/u/Pbonamy)\ **Post date:** [December 11, 2022, 3:19pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/9 "2022-12-11T15:19:41Z")
I try with cartesian, same problem. it seems the command for the motor don’t work the motor turn one way and after one second the other way then other way until printer stops. ---
**Author:** ![Pbonamy](https://avatars.discourse-cdn.com/v4/letter/p/ea666f/32.png) [@Pbonamy](https://klipper.discourse.group/u/Pbonamy)\ **Post date:** [December 11, 2022, 3:48pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/10 "2022-12-11T15:48:30Z")
Now it’s working withe cartesian kinematics, I don’t know why, I have just uncoment all lines about safe z home and bedmesh. Thank all for help ---
**Author:** ![jrobbom5](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/jrobbom5/32/3187_2.png) [@jrobbom5](https://klipper.discourse.group/u/jrobbom5)\ **Post date:** [December 11, 2022, 3:55pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/11 "2022-12-11T15:55:08Z")
Glad you got it working 🙂 ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [April 24, 2024, 1:24pm UTC](https://klipper.discourse.group/t/ender-5-pro-problem-x-homing/5321/12 "2024-04-24T13:24:51Z")