# Ender 6 with BIGTREETECH SKR MINI E3 V3.0 **URL:** \ **Category:** General Discussion\ **Created:** [October 5, 2022, 1:14am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341 "2022-10-05T01:14:45Z")\ **Posts on this page:** 16\ **Page:** 1
**Author:** ![rtremmel](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/rtremmel/32/2373_2.png) [@rtremmel](https://klipper.discourse.group/u/rtremmel)\ **Post date:** [October 5, 2022, 1:14am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/1 "2022-10-05T01:14:45Z")
Does anyone have a config file for an Ender 6 with an SKR V3 using the stock display? Thank you! ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 5, 2022, 5:57am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/2 "2022-10-05T05:57:16Z")
Hello @rtremmel ! You may find one here: > **[klipper/config at master · Klipper3d/klipper](https://github.com/Klipper3d/klipper/tree/master/config)** > > master/config ---
**Author:** ![rtremmel](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/rtremmel/32/2373_2.png) [@rtremmel](https://klipper.discourse.group/u/rtremmel)\ **Post date:** [October 5, 2022, 2:22pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/3 "2022-10-05T14:22:01Z")
I checked. There is a **printer-creality-ender6-2020.cfg** and a **generic-bigtreetech-skr-mini-e3-v3.0.cfg**. I am merging them. But I was hoping to find someone who already had it working. This is my first Kilpper install. I have been using Marlin for the past 5 years. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 5, 2022, 5:43pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/4 "2022-10-05T17:43:12Z")
Don’t worry, It’s not that difficult. I created a config for a T-Rex 3 from scratch. And it works fine. ---
**Author:** ![tmarto](https://avatars.discourse-cdn.com/v4/letter/t/7ea924/32.png) [@tmarto](https://klipper.discourse.group/u/tmarto)\ **Post date:** [October 13, 2022, 3:30pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/5 "2022-10-13T15:30:54Z")
Hi. @EddyMI3D : have you been able to complete the Ender 6 + SKR mini e3 V3 ? I have been trying to get it to work, but having issues with the Y Axis. At this this stage, i’m not sure if this is an config issue, or wiring issue. If you have it working, can you please share ? Regards, Tiago ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [October 13, 2022, 3:42pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/6 "2022-10-13T15:42:49Z")
Hello @tmarto ! I don’t have a Ender 6 and I do not work on one. I just gave a hint where to find a config file. ---
**Author:** ![tmarto](https://avatars.discourse-cdn.com/v4/letter/t/7ea924/32.png) [@tmarto](https://klipper.discourse.group/u/tmarto)\ **Post date:** [October 13, 2022, 4:04pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/7 "2022-10-13T16:04:13Z")
Tks @EddyMI3D. @rtremmel : were you able to get the config file working ? ---
**Author:** ![rtremmel](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/rtremmel/32/2373_2.png) [@rtremmel](https://klipper.discourse.group/u/rtremmel)\ **Post date:** [October 18, 2022, 12:17am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/8 "2022-10-18T00:17:40Z")
I am new to Klipper so I decided to get the SKR Mini E3 V3 working with Marlin 2.1.1 first. It turns out the Ender 6 is actually a Core **YX** machine, but I discovered this AFTER I got a working configuration. This works for me: ```auto #define COREXY #define INVERT_X_DIR true #define INVERT_Y_DIR false #define INVERT_Z_DIR true ``` **AND** I had to reverse the X and Y stepper plugs on the BTT controller. If I had specified COREYX it might have been easier. I had to flash the firmware about six times to get a working combination! I never did get the stock display working. I even updated its firmware. So I bought a BTT TFT35 V3.01. I am still having some issues getting it working. ---
**Author:** ![xIExodusIx](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/xiexodusix/32/3592_2.png) [@xIExodusIx](https://klipper.discourse.group/u/xIExodusIx)\ **Post date:** [January 22, 2023, 7:27pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/9 "2023-01-22T19:27:23Z")
Hi rtremmel, I got the same configuration, an Ender 6 with BLTouch installed using a BTT SKR E3 Mini V3.0 with BTT TFT35 V3.0.1 under Marlin 2.1.2 and have some trouble get it work correctly, maybe you can help me a little bit. The TFT is running pretty good, after I had installed the correct firmware. I had to take the BIGTREE\_GD\_TFT35\_V3.0.27.x.bin for my TFT. You can edit the config.ini file to make changes to the TFT firmware, you don’t have to flash the firmware completely new. It took me about 2 Months to get the Marlin 2.1.2 firmware to work. Today I made my first few testprints, tried to print a Benchy. My issue is the writing on the first Layer of the Benchy is upside down. Maybe it is while I have other settings in the configuration.h as you. I have: #define COREXY #define INVERT\_X\_DIR false #define INVERT\_Y\_DIR true #define INVERT\_Z\_DIR true And I have also: #define USE\_YMIN\_PLUG #define USE\_ZMIN\_PLUG → this must be set for the BLTouch! #define USE\_XMAX\_PLUG What did you mean with “reverse the X and Y stepper plug on the BTT controller”? Could you please explain? Thank you. ---
**Author:** ![rtremmel](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/rtremmel/32/2373_2.png) [@rtremmel](https://klipper.discourse.group/u/rtremmel)\ **Post date:** [January 24, 2023, 12:12am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/10 "2023-01-24T00:12:39Z")
I had to physically swap the X and Y servo connectors on the BTT SKR E3 Mini V3 board. Here is the configuration that works for me: ```auto #define COREXY // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. // This config for BIGTREETECH SKR MINI E3 V3.0 requires swapping the X and Y stepper connectors. #define INVERT_X_DIR true #define INVERT_Y_DIR false #define INVERT_Z_DIR true ``` I subsequently read the Ender-6 is actually a COREYX printer rather than a COREXY; but by then I figured out the configuration above works with the X and Y servo cables reversed. ---
**Author:** ![xIExodusIx](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/xiexodusix/32/3592_2.png) [@xIExodusIx](https://klipper.discourse.group/u/xIExodusIx)\ **Post date:** [January 26, 2023, 2:53pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/11 "2023-01-26T14:53:51Z")
Hi rtremmel, I made now the changes, inverted the stepper cable of the X and Y axis, and got the printer to work again, but I have the same issue. If there is a writing on the first layer(s), it is printed mirrored, and so not really readable. I have been at this point before, without inverting the cable of the x and y stepper. But thanks in anyway for your help. ---
**Author:** ![shauntam232](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@shauntam232](https://klipper.discourse.group/u/shauntam232)\ **Post date:** [February 19, 2023, 8:07pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/12 "2023-02-19T20:07:02Z")
did you happen to get config working as i have ender 6 with skr mini v3 im having trouble with config? ---
**Author:** ![rtremmel](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/rtremmel/32/2373_2.png) [@rtremmel](https://klipper.discourse.group/u/rtremmel)\ **Post date:** [February 20, 2023, 2:03am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/13 "2023-02-20T02:03:13Z")
No. I never got around to installing Klipper. Still running the latest Marlin version. ---
**Author:** ![shauntam232](https://avatars.discourse-cdn.com/v4/letter/s/b2d939/32.png) [@shauntam232](https://klipper.discourse.group/u/shauntam232)\ **Post date:** [February 20, 2023, 2:45am UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/14 "2023-02-20T02:45:53Z")
Well i got it to work but had to switch the x and y wires for steppers on board then everything worked ---
**Author:** ![rtremmel](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/rtremmel/32/2373_2.png) [@rtremmel](https://klipper.discourse.group/u/rtremmel)\ **Post date:** [February 20, 2023, 1:34pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/15 "2023-02-20T13:34:14Z")
Good to know. Thanks. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [April 24, 2024, 1:22pm UTC](https://klipper.discourse.group/t/ender-6-with-bigtreetech-skr-mini-e3-v3-0/4341/17 "2024-04-24T13:22:10Z")
Closed on April 24, 2024, 1:22pm UTC