# Ender5 - Shifts on X &Y axis

**URL:** <https://klipper.discourse.group/t/ender5-shifts-on-x-y-axis/14328>\
**Category:** General Discussion\
**Created:** [February 21, 2024, 9:01pm UTC](https://klipper.discourse.group/t/ender5-shifts-on-x-y-axis/14328 "2024-02-21T21:01:39Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Arcube101](https://avatars.discourse-cdn.com/v4/letter/a/cab0a1/32.png) [@Arcube101](https://klipper.discourse.group/u/Arcube101)\
**Post date:** [February 21, 2024, 9:01pm UTC](https://klipper.discourse.group/t/ender5-shifts-on-x-y-axis/14328/1 "2024-02-21T21:01:40Z")

</div>

### Basic Information:

Printer Model: Ender5-Pro (CoreXY Zero G Mercury One)  
 MCU / Printerboard: BTT SKR 1.4 Turbo  
 `klippy.log`  
[klippy.log](https://klipper.discourse.group/uploads/short-url/uVH6bABAy6d3cfFAaQ7HzzcB27e.log) (2.9 MB)

_Fill out above information and_ **_in all cases attach your_ `klippy.log` _file_** (use zip to compress it, if too big). _Pasting your_ `printer.cfg` _is **not** needed_  
_ **Be sure to check our “Knowledge Base” Category first. Most relevant items, e.g. error messages, are covered there** _

### Describe your issue:

Starts fine but while printing, the X & Y axis start to shift, video in imgur link would explain it the best.

[[Album] imgur.com ![](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/e/ecda01670e4de817d94d893a76ae9300092283dc.jpeg "imgur.com") ](https://imgur.com/a/EAFb4IY)

- I think it is something to do with my settings
- Have tried reducing acceleration with no luck

The reason I think something is wrong with my klipper settings is because I had same problem on mostly stock creality Ender5 (except SKR mobo).

TIA for any suggestions.

---

<div class="post-metadata">

**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\
**Post date:** [February 22, 2024, 7:14am UTC](https://klipper.discourse.group/t/ender5-shifts-on-x-y-axis/14328/2 "2024-02-22T07:14:43Z")

</div>

I rather believe that this is a mechanical problem, like binding axes.

Also, you have a quite high run\_current for X and Y, which would likely need active cooling for the stepper drivers (also make sure your steppers are OK with this)

---

<div class="post-metadata">

**Author:** ![Arcube101](https://avatars.discourse-cdn.com/v4/letter/a/cab0a1/32.png) [@Arcube101](https://klipper.discourse.group/u/Arcube101)\
**Post date:** [February 22, 2024, 10:17pm UTC](https://klipper.discourse.group/t/ender5-shifts-on-x-y-axis/14328/3 "2024-02-22T22:17:18Z")

</div>

Thank you. I also suspected that something is binding in coreXY.

However earlier it was cartesian on mostly stock Ender5 which makes me wonder if my klipper settings are correct - did you notice anything wrong?

Unfortunately I did not take a video of the cartesian, I only have pics which are attached to this reddit post - [Reddit - Dive into anything](https://www.reddit.com/r/ender5/comments/1ahgugl/ender_5_pro_klipper_learned_to_do_steppe_printing/)

Yes, there is active cooling on TMC drivers (140mm 24v fan blowing at full speed), also the motors are LDO 2.8a and they do not get warm so I think I am okay there.

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\
**Post date:** [April 22, 2024, 10:17pm UTC](https://klipper.discourse.group/t/ender5-shifts-on-x-y-axis/14328/4 "2024-04-22T22:17:25Z")

</div>

This topic was automatically closed 60 days after the last reply. New replies are no longer allowed.