# Klipper installation failure on Anycubic Kobra 2 neo

**URL:** <https://klipper.discourse.group/t/klipper-installation-failure-on-anycubic-kobra-2-neo/26293>\
**Category:** General Discussion\
**Created:** [September 23, 2026, 8:31pm UTC](https://klipper.discourse.group/t/klipper-installation-failure-on-anycubic-kobra-2-neo/26293 "2026-09-23T20:31:47Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![ivabarlay](https://avatars.discourse-cdn.com/v4/letter/i/35a633/32.png) [@ivabarlay](https://klipper.discourse.group/u/ivabarlay)\
**Post date:** [September 23, 2026, 8:31pm UTC](https://klipper.discourse.group/t/klipper-installation-failure-on-anycubic-kobra-2-neo/26293/1 "2026-09-23T20:31:47Z")

</div>

### Basic Information:

Printer Model: Anycubic Kobra 2 Neo  
 MCU / Printerboard: GD32F303  
 Host / SBC  
 klippy.log

_Fill out above information and_ _ **in all cases attach your** _ **`klippy.log` _file_** (use zip to compress it, if too big). _Pasting your_ `printer.cfg` _is **not** needed_  
_ **Be sure to check our “Knowledge Base” Category first. Most relevant items, e.g. error messages, are covered there** _

### Describe your issue:

Hi!

I have followed many guides for installing Klipper on this specific machine, but I can’t seem to even try to upload the firmware; when I insert the micro sd card with the firmware.bin file in the correct FAT format, it just ignores it. I have tried compiling the firmware myself as well as trying others.

I am beggining to think the printerboard is adjusted so I can’t change its firmware in any way, not even the original one from the manufacturer.

Links to the guides I followed:

- [Klipper (MOD) - Kobra2Neo Insights](https://1coderookie.github.io/Kobra2NeoInsights/firmware/fw_klipper/)
- [Getting orange pi 3 lts + klipper working with anycubic kobra 2 neo - #88 by robertocrr](https://klipper.discourse.group/t/getting-orange-pi-3-lts-klipper-working-with-anycubic-kobra-2-neo/11278/88)

Thank you!

---

<div class="post-metadata">

**Author:** ![cardoc](https://avatars.discourse-cdn.com/v4/letter/c/ec9cab/32.png) [@cardoc](https://klipper.discourse.group/u/cardoc)\
**Post date:** [September 23, 2026, 11:25pm UTC](https://klipper.discourse.group/t/klipper-installation-failure-on-anycubic-kobra-2-neo/26293/2 "2026-09-23T23:25:15Z")

</div>

> [@ivabarlay](#):
>
> I have followed many guides

A link to the guide you are using now would be helpfull.  
Your printer still boots to the Marlin screen?

Have you read this thread?

> [@Getting orange pi 3 lts + klipper working with anycubic kobra 2 neo](https://klipper.discourse.group/t/getting-orange-pi-3-lts-klipper-working-with-anycubic-kobra-2-neo/11278/88):
>
> I tried this setup in my printer. No luck. For my own sanity i will retreat a couple of weeks from this subject, until there is enough information to have a working bin file and a working cfg. Happy new year everybody. Thank you for your engagement and patience.

---

<div class="post-metadata">

**Author:** ![ivabarlay](https://avatars.discourse-cdn.com/v4/letter/i/35a633/32.png) [@ivabarlay](https://klipper.discourse.group/u/ivabarlay)\
**Post date:** [September 24, 2026, 12:13pm UTC](https://klipper.discourse.group/t/klipper-installation-failure-on-anycubic-kobra-2-neo/26293/3 "2026-09-24T12:13:18Z")

</div>

My bad, I will edit the post with the links. And yes, it boots to the Marlin screen like nothing happened.

I followed the same thread you posted and this one: [Klipper (MOD) - Kobra2Neo Insights](https://1coderookie.github.io/Kobra2NeoInsights/firmware/fw_klipper/) .