# Klipper on ender 3 v3 Plus?

**URL:** <https://klipper.discourse.group/t/klipper-on-ender-3-v3-plus/22055>\
**Category:** General Discussion\
**Created:** [February 17, 2025, 9:31pm UTC](https://klipper.discourse.group/t/klipper-on-ender-3-v3-plus/22055 "2025-02-17T21:31:07Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Khisanthax](https://avatars.discourse-cdn.com/v4/letter/k/3da27b/32.png) [@Khisanthax](https://klipper.discourse.group/u/Khisanthax)\
**Post date:** [February 17, 2025, 9:31pm UTC](https://klipper.discourse.group/t/klipper-on-ender-3-v3-plus/22055/1 "2025-02-17T21:31:07Z")

</div>

I have an ender 3 v3 plus which runs creality OS but I’d much rather have it connected to full klipper. I’ve seen people successfully use the ender 3 v3 se with klipper but not the v3 or v3 plus. Has anyone been able to use it with the v3 plus?

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [February 18, 2025, 6:42am UTC](https://klipper.discourse.group/t/klipper-on-ender-3-v3-plus/22055/2 "2025-02-18T06:42:36Z")

</div>

Hello @Khisanthax !

The Ender 3 V3 Plus comes with it’s own Klipper ecosystem (mangled by Creality).

The most easy way to run the printer on genuine Klipper is

- A new printer board
- A SBC (e.g. Raspberry Pi)

You may have a look here: [3D Printers with Preinstalled and Modified Klipper Versions](https://klipper.discourse.group/t/3d-printers-with-preinstalled-and-modified-klipper-versions/20467/1)

---

<div class="post-metadata">

**Author:** ![Khisanthax](https://avatars.discourse-cdn.com/v4/letter/k/3da27b/32.png) [@Khisanthax](https://klipper.discourse.group/u/Khisanthax)\
**Post date:** [February 19, 2025, 4:47pm UTC](https://klipper.discourse.group/t/klipper-on-ender-3-v3-plus/22055/3 "2025-02-19T16:47:40Z")

</div>

I have a mini PC that runs four printers already and if I were to do this would want to add the v3 plus to that machine.

My initial concern with flashing the board with klipper is that it uses a strain sensor for z offset and bed mesh, so I didn’t know if there was a config that could handle this or if I would just lose it? And secondly if there was a firmware for this printer/board.

This printer, I believe, has a breakout board on the back and that complicated things if I want to replace the board.

I’ll take a look at the link!

P.S. mangled is generous

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\
**Post date:** [April 20, 2025, 4:48pm UTC](https://klipper.discourse.group/t/klipper-on-ender-3-v3-plus/22055/4 "2025-04-20T16:48:35Z")

</div>

This topic was automatically closed 60 days after the last reply. New replies are no longer allowed.