# Mainsail Klippy-state: error **URL:** \ **Category:** General Discussion\ **Created:** [April 26, 2022, 12:35am UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704 "2022-04-26T00:35:08Z")\ **Posts on this page:** 8\ **Page:** 1
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [April 26, 2022, 12:35am UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/1 "2022-04-26T00:35:08Z")
I have three problems as follows : \*mcu ‘mcu’: Unable to connect Once the underlying issue is corrected, use the “FIRMWARE\_RESTART” command to reset the firmware, reload the config, and restart the host software. Error configuring printer \*printer is not ready \*Unparsed config option ‘type: web’ detected in section [update\_manager]. This may be an option no longer available or could be the result of a module that failed to load. In the future this will result in a startup error. \*\*\* attached below the moonraker log [moonraker (1).log](https://klipper.discourse.group/uploads/short-url/vE9dxHV9ZCsVN28wVncfXT5ATWf.log) (149.0 KB) ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [April 26, 2022, 5:07am UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/2 "2022-04-26T05:07:21Z")
In `moonraker.conf` change ```auto [update_manager] refresh_interval = 168 type = web repo = mainsail-crew/mainsail path = ~/mainsail ``` to ```auto [update_manager mainsail] refresh_interval = 168 type = web repo = mainsail-crew/mainsail path = ~/mainsail ``` and post your `klippy.log` file ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [April 26, 2022, 3:02pm UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/4 "2022-04-26T15:02:54Z")
still need some help to make the printer ready ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [April 26, 2022, 3:32pm UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/5 "2022-04-26T15:32:38Z")
[http://paste.c-net.org/MadamBunny](http://paste.c-net.org/MadamBunny) ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [April 26, 2022, 4:15pm UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/6 "2022-04-26T16:15:36Z")
Most likely your board is not correctly flashed. Carefully work through [Installation - Klipper documentation](https://www.klipper3d.org/Installation.html) and also check the instructions on top of your respective cfg from here: [klipper/config at master · Klipper3d/klipper · GitHub](https://github.com/Klipper3d/klipper/tree/master/config) ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [April 26, 2022, 9:59pm UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/7 "2022-04-26T21:59:22Z")
I’m sure that … I’m having an issue with flashing klipper.bin using SD card do u know any way to flash it using … ssh … the printer is serial connected i have tried once a method earlier via ssh but i can’t remember it any more ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [April 27, 2022, 5:54am UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/8 "2022-04-27T05:54:24Z")
Well, since you did not even provide what type of board you are using, it is hard to give any advice. Following above instructions and especially using the correct options for `make menuconfig` according to your board, are usually working if done correctly. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [June 11, 2024, 4:57am UTC](https://klipper.discourse.group/t/mainsail-klippy-state-error/2704/9 "2024-06-11T04:57:46Z")