# Move only one motor, not an axis, and not stepper\_buzz

**URL:** <https://klipper.discourse.group/t/move-only-one-motor-not-an-axis-and-not-stepper-buzz/19256>\
**Category:** General Discussion\
**Created:** [October 7, 2024, 1:44pm UTC](https://klipper.discourse.group/t/move-only-one-motor-not-an-axis-and-not-stepper-buzz/19256 "2024-10-07T13:44:06Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![JuanR3D](https://avatars.discourse-cdn.com/v4/letter/j/7993a0/32.png) [@JuanR3D](https://klipper.discourse.group/u/JuanR3D)\
**Post date:** [October 7, 2024, 1:44pm UTC](https://klipper.discourse.group/t/move-only-one-motor-not-an-axis-and-not-stepper-buzz/19256/1 "2024-10-07T13:44:06Z")

</div>

### Basic Information:

Printer Model: Custom  
 MCU / Printerboard: Manta M8P  
 Host / SBC: CB1

### Describe your issue:

I have my printer configured and everything working ok. Neverthless, i want to move an specified motor, for example, for maintenance tasks in my printer.

For now, i just disconnect some motor cables, and command the printer to move the desired axis, in this way, only the desired motors will move. However, i prefer not to do this but do it via software.

Is there a way to do this?

I have tried to configure a manual\_stepper in the same pins as my steppers and create a duplicate\_pin\_override section, but it doesn’t work.

---

<div class="post-metadata">

**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\
**Post date:** [October 7, 2024, 1:51pm UTC](https://klipper.discourse.group/t/move-only-one-motor-not-an-axis-and-not-stepper-buzz/19256/2 "2024-10-07T13:51:07Z")

</div>

[FORCE\_MOVE](https://www.klipper3d.org/G-Codes.html#force_move_1)

---

<div class="post-metadata">

**Author:** ![JuanR3D](https://avatars.discourse-cdn.com/v4/letter/j/7993a0/32.png) [@JuanR3D](https://klipper.discourse.group/u/JuanR3D)\
**Post date:** [October 7, 2024, 2:02pm UTC](https://klipper.discourse.group/t/move-only-one-motor-not-an-axis-and-not-stepper-buzz/19256/3 "2024-10-07T14:02:58Z")

</div>

Thanks a lot! @Sineos

It works perfectly.

---

<div class="post-metadata">

**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\
**Post date:** [November 7, 2024, 12:03am UTC](https://klipper.discourse.group/t/move-only-one-motor-not-an-axis-and-not-stepper-buzz/19256/4 "2024-11-07T00:03:41Z")

</div>

This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.