# Move out of range: 37.259 -49.197 1.000 \[0.000\] **URL:** \ **Category:** General Discussion\ **Created:** [May 12, 2023, 5:37pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354 "2023-05-12T17:37:13Z")\ **Posts on this page:** 12\ **Page:** 1
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 12, 2023, 5:37pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/1 "2023-05-12T17:37:13Z")
### Basic Information: Printer Model: Ender 3 V2 MCU / Printerboard:4.2.2 `klippy.log [klippy (4).log|attachment](upload://8F3T2jKc1A432rpNoF0k6Gk7T2y.log) (526.0 KB) ` _Fill out above information and_ **_in all cases attach your_ `klippy.log` _file_**. _Pasting your_ `printer.cfg` _is **not** needed_ _**Be sure to check our [Knowledge Base](https://klipper.discourse.group/t/about-the-knowledge-base-category-table-of-contents/6228) and in particular [this](https://klipper.discourse.group/t/how-to-trouble-shoot/6326) and [this](https://klipper.discourse.group/t/how-to-ask-for-help/6327) post**_ my problem this Messege (Unknown command:“M302” )&(Move out of range: 37.259 -49.197 1.000 ) ### Describe your issue: …I have modified my printer to print clay … so i need to use cold extrusion So i used in my start machine setting in the slicer the following: ; Ender 3 Custom Start G-code M302 P1 …N.B" i tried also P0" G92 E0 ; Reset Extruder G28 ; Home all axes G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish … and in the end setting M302 P0 G91 ;Relative positioning G1 E-2 F2700 ;Retract and raise Z G1 E-2 Z0.2 F2400 ;Retract and raise Z G1 X5 Y5 F3000 ;Wipe out G1 Z10 ;Rate Z more G90 ;Absolute positioning G1 X0 Y{machine\_depth} ;present print M106 S0 ;Turn-off fan M104 S0 ;Turn-off hotend M140 S0 ;Turn-off bed I got the unknown command M302!! … i need to cancel all Temp .. the bed and extrude temp permantly any help ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [May 12, 2023, 9:52pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/2 "2023-05-12T21:52:12Z")
M302 is not a known GCODE for Klipper. You basically have two options: 1. Set respective limits: ```auto min_temp=-273.15 min_extrude_temp=-273.15 max_temp=99999999 ``` 2. Wire a thermistor and simply let it measure room temperature and set appropriate limits. For the other error see [Move out of range: X Y Z [E]](https://klipper.discourse.group/t/move-out-of-range-x-y-z-e/6637/1) Most likely due to a mixup between `G90` / `G91`. I’d recommend to work with `G90` and always give coordinates as absolute in relation to your 0/0 origin. `G91` is incremental / relative, this means always moves from your current position and as such easily creates such errors. In your case most likely the Y axis with a commanded target of -49 ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 15, 2023, 4:33pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/3 "2023-05-15T16:33:49Z")
Hello Bro how are As i mentioned earlier … that … know i’ve modified my Ender 3V2 to print Clay … so i don’t need heaters or hotend or sensors or even fan !! So i have removed its cables 🙂 So it gave my the following error "Klipper reports: SHUTDOWN MCU ‘mcu’ shutdown: ADC out of range This generally occurs when a heater temperature exceeds its configured min\_temp or max\_temp. Once the underlying issue is corrected, use the “FIRMWARE\_RESTART” command to reset the firmware, reload the config, and restart the host software. Printer is shutdown" Can u help my in this modification ---
**Author:** ![hcet14](https://avatars.discourse-cdn.com/v4/letter/h/ecd19e/32.png) [@hcet14](https://klipper.discourse.group/u/hcet14)\ **Post date:** [May 15, 2023, 4:47pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/4 "2023-05-15T16:47:39Z")
> [@ahmedbadran](#): > > I have modified my printer to print clay cool 👌 Your klippy.log might help. Good luck, hcet14 ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 15, 2023, 4:50pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/5 "2023-05-15T16:50:52Z")
[klippy (6).log](https://klipper.discourse.group/uploads/short-url/yuDRGQANJmo6LSnvKJCa3GqaDPG.log) (158.3 KB) Sorry … here the log attached … ---
**Author:** ![hcet14](https://avatars.discourse-cdn.com/v4/letter/h/ecd19e/32.png) [@hcet14](https://klipper.discourse.group/u/hcet14)\ **Post date:** [May 15, 2023, 5:14pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/6 "2023-05-15T17:14:19Z")
> [@ahmedbadran](#): > > So i have removed its cables Connect all connectors back! Then you have to tell Klipper the margins you expect. You are printing clay =\> no need for a hot bed, etc… There is only one way. Read the very good documentation and set the right margins for your clay print. ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 15, 2023, 5:15pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/7 "2023-05-15T17:15:40Z")
i have Removed all following cabels ( thermo. sensor, Hotend, the 2 fans ) Also in the sliced file i have to modify with same reading in MainSail in my case was -43 ( What i modifed in the file was the following lines \*;nozzle\_temperature(°C): -43 M104 S-43 M105 M109 S-43) … I believe this will solve the first issue ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 15, 2023, 5:18pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/8 "2023-05-15T17:18:49Z")
Regarding the Move out of range: X Y Z [E] i didn’t get your point … ill attach file i want to print in GCODE and klippy.log [2mmCE3E3V2\_viktoria\_with\_turner\_logo.gcode](https://klipper.discourse.group/uploads/short-url/wDXWaxzS8YpmyS3T2PgCedWJjvD.gcode) (1.4 MB) [klippy (6).log](https://klipper.discourse.group/uploads/short-url/yuDRGQANJmo6LSnvKJCa3GqaDPG.log) (158.3 KB) ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 15, 2023, 5:21pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/9 "2023-05-15T17:21:27Z")
Thnx for you kind help and time Bro … But i believe i have solved the Temp Issue as i mentioned above … thanks again … realy appreciate your support ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [May 15, 2023, 6:19pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/10 "2023-05-15T18:19:04Z")
Your gcode file looks strange: ```auto G0 F6000 X37.259 Y-49.197 Z1 ;TYPE:SKIRT G1 F1200 X38.172 Y-49.185 E0.28626 ``` It tries to move to a Y position of -49. Your printer is defined as printing area between 0 and +235. Seems your slicer is messed up. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [May 15, 2023, 6:20pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/11 "2023-05-15T18:20:49Z")
Obviously set the origin to the middle of the bed. ---
**Author:** ![ahmedbadran](https://avatars.discourse-cdn.com/v4/letter/a/6bbea6/32.png) [@ahmedbadran](https://klipper.discourse.group/u/ahmedbadran)\ **Post date:** [May 21, 2023, 1:19pm UTC](https://klipper.discourse.group/t/move-out-of-range-37-259-49-197-1-000-0-000/8354/12 "2023-05-21T13:19:01Z")
Both you and Sineos are right … except that it was marked the origin in the middel of the bed … so i removed its selection … and the slicer works fine NOW!!! Thnx Buddies