# Move out of range error / Klipper / Cura **URL:** \ **Category:** General Discussion\ **Created:** [January 22, 2025, 6:30pm UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563 "2025-01-22T18:30:46Z")\ **Posts on this page:** 7\ **Page:** 1
**Author:** ![3dpjunkie](https://avatars.discourse-cdn.com/v4/letter/3/50afbb/32.png) [@3dpjunkie](https://klipper.discourse.group/u/3dpjunkie)\ **Post date:** [January 22, 2025, 6:30pm UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/1 "2025-01-22T18:30:46Z")
Printer Model: Neptune 3 Plus MCU / Printerboard: stm32f401xc Version: v0.11.0-53-gb337cc3e Host / SBC: Raspberry Pi 3b [klippy(2).log](https://klipper.discourse.group/uploads/short-url/jU84q840ispemT4Omh7KdZ9nY7E.log) (5.7 MB) [config-20250122-132451.zip](https://klipper.discourse.group/uploads/short-url/71fXiycfdckvstaDsC2HXAhf8Fn.zip) (3.8 KB) Hey everyone, I’m new to 3d printing and have been trying to get klipper setup to run with my Neptune 3 Plus. I’ve got a Raspberry Pi 3b running the latest version of Klipper. I’m using Cura as a slicer. I’ve tried adding a START\_PRINT script I found in the forums to help with the “Move out of range” error i’m getting. I’ve tried setting the bed mesh and the nozzle location etc. I’ve tried following the “Understanding X and Y Axes Limits and Homing” guide but maybe i’m just not getting it. I’ve attached my klippy logs as well as my printer config. I’m sure by this point i’ve got it jacked up pretty good. I’m hoping its a simple config fix. Thanks in advance for the help. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [January 22, 2025, 6:55pm UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/2 "2025-01-22T18:55:35Z")
Hello @3dpjunkie You have to align - bed size - probe offset - bed mesh > [@Understanding X and Y Axes Limits and Homing](https://klipper.discourse.group/t/understanding-x-and-y-axes-limits-and-homing/10779/1): > > The X and Y Axis Klipper needs to know from its printer.cfg settings how far the X and Y axes can safely move without hitting the printer’s frame. It also needs to know where the origin (X=0 / Y=0) is. This origin is the beginning of the usable printer bed. In the following, we assume a Cartesian printer that follows the conventions of a [Cartesian Coordinate System](https://en.wikipedia.org/wiki/Cartesian_coordinate_system). This is also the reason why it is a quasi-standard to define the origin as the left-front corner of the bed. This way, all logic… Also: ```auto Git version: 'v0.12.0-410-gcf3b0475d-dirty' Untracked files: klippy/extras/auto_speed.py ``` ---
**Author:** ![3dpjunkie](https://avatars.discourse-cdn.com/v4/letter/3/50afbb/32.png) [@3dpjunkie](https://klipper.discourse.group/u/3dpjunkie)\ **Post date:** [January 22, 2025, 8:35pm UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/3 "2025-01-22T20:35:59Z")
Thanks for the quick reply. I’ll re-read that article and try to figure it out. Regarding the autospeed.py thing, should I just remove that completely? I just thought it would speed print times a little. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [January 22, 2025, 8:47pm UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/4 "2025-01-22T20:47:47Z")
First I would prioritize a proper print - later you can think about speeding up 😉 ---
**Author:** ![3dpjunkie](https://avatars.discourse-cdn.com/v4/letter/3/50afbb/32.png) [@3dpjunkie](https://klipper.discourse.group/u/3dpjunkie)\ **Post date:** [January 23, 2025, 1:01am UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/5 "2025-01-23T01:01:40Z")
I agree 100%. I had it printing really well using Cura and the firmware that came on the Neptune 3 Plus. I’ll try to get it working with Klipper ---
**Author:** ![3dpjunkie](https://avatars.discourse-cdn.com/v4/letter/3/50afbb/32.png) [@3dpjunkie](https://klipper.discourse.group/u/3dpjunkie)\ **Post date:** [January 23, 2025, 5:05am UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/6 "2025-01-23T05:05:50Z")
Just finished up a 3 hour print after setting the x/y parameters. I guess I missed something the first time around because this was crazy easy to do. Turned out perfect, thanks for your help. ---
**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\ **Post date:** [February 22, 2025, 3:06pm UTC](https://klipper.discourse.group/t/move-out-of-range-error-klipper-cura/21563/7 "2025-02-22T15:06:02Z")
This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.