# Move out of range ？

**URL:** <https://klipper.discourse.group/t/move-out-of-range/3812>\
**Category:** General Discussion\
**Created:** [August 12, 2022, 3:54am UTC](https://klipper.discourse.group/t/move-out-of-range/3812 "2022-08-12T03:54:20Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![Jason\_86](https://avatars.discourse-cdn.com/v4/letter/j/8797f3/32.png) [@Jason\_86](https://klipper.discourse.group/u/Jason_86)\
**Post date:** [August 12, 2022, 3:54am UTC](https://klipper.discourse.group/t/move-out-of-range/3812/1 "2022-08-12T03:54:20Z")

</div>

Hello everyone, I’m new here, and I assembling a BLV mgn Cube, BL-TOUCH and BED MESH have been matched,and when I start printing, the move out of range error appears after the heating bed and extrusion head are heated.

 ![微信图片_20220812115322](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/d/deee7ac972a8d255c08da79c03b708501f8e5a0c.png)

---

<div class="post-metadata">

**Author:** ![Jason\_86](https://avatars.discourse-cdn.com/v4/letter/j/8797f3/32.png) [@Jason\_86](https://klipper.discourse.group/u/Jason_86)\
**Post date:** [August 12, 2022, 5:06am UTC](https://klipper.discourse.group/t/move-out-of-range/3812/2 "2022-08-12T05:06:38Z")

</div>

[klippy .log](https://klipper.discourse.group/uploads/short-url/3xKylFB4mZe6GuyHvIYg3pQB28w.log) (1.2 MB)

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [August 12, 2022, 6:20am UTC](https://klipper.discourse.group/t/move-out-of-range/3812/3 "2022-08-12T06:20:47Z")

</div>

Hello @Jason_86 !

There are some points in your klippy.log/printer.cfg that are a bit obscure:

```auto
[stepper_x]
...
position_endstop = -20
position_max = 310
position_min = -20
...

```

I assume you use that wide negative area for a purpose.

Your BLtouch is 40 mm to the left of the nozzle:

```auto
[bltouch]
... 
x_offset = -40
y_offset = 0
...

```

So you have at leas start at 40, better 50, for the mash grid for X.  
With start at 10, it is, regarding you start at -20, at 10mm left out of the bed (all values in X direction).

From

```auto
[bed_mesh]
...
mesh_min = 10,10
mesh_max = 265,265
...

```

to

```auto
[bed_mesh]
...
mesh_min = 50,10
mesh_max = 265,265
...

```

Your issue is reporting a negative Y value. The printer starts at Y=0.

You may share the the zipped gcode file here, so we can see that going wrong.

Also there is this:

```auto
Unknown command:"HYPERLAPSE"

```

That command is not defined in the printer.cfg

---

<div class="post-metadata">

**Author:** ![Jason\_86](https://avatars.discourse-cdn.com/v4/letter/j/8797f3/32.png) [@Jason\_86](https://klipper.discourse.group/u/Jason_86)\
**Post date:** [August 12, 2022, 6:46am UTC](https://klipper.discourse.group/t/move-out-of-range/3812/4 "2022-08-12T06:46:20Z")

</div>

Thanks for your help, this is the gcode file  
[TEST.zip](https://klipper.discourse.group/uploads/short-url/c1Mq6UfVncwUGfSR027ApX7Wjmx.zip) (910.7 KB)

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [August 12, 2022, 7:06am UTC](https://klipper.discourse.group/t/move-out-of-range/3812/5 "2022-08-12T07:06:56Z")

</div>

Actually, your print goes quite a lot into the negative area:

```auto
...
;TYPE:SKIRT
G1 F1500 E0
G1 F2700 X9.966 Y-22.71 E0.03941
G1 X10.747 Y-22.59 E0.07884
G1 X11.511 Y-22.393 E0.1182
G1 X12.252 Y-22.118 E0.15763
G1 X12.961 Y-21.771 E0.19701
G1 X13.631 Y-21.353 E0.23641
G1 X14.256 Y-20.87 E0.27582
G1 X14.692 Y-20.465 E0.30551
G1 X20.465 Y-14.692 E0.71282
...

```

And also at X

```auto
...
G1 F2700 X14.01 Y8.942 E217.63242
G1 X8.942 Y14.01 E217.75161
G1 X-8.942 Y14.01 E218.04903
G1 X-14.01 Y8.943 E218.1682
G1 X-14.01 Y-8.942 E218.46563
G1 X-8.943 Y-14.01 E218.58481
G1 X8.942 Y-14.01 E218.88224
...

```

For a CoreXY printer, you have to set the start point lower left. (Uncheck Origin at center).

![grafik](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/6/692553923e260bc4f8acd731339af9df76c669b1.png)

---

<div class="post-metadata">

**Author:** ![Jason\_86](https://avatars.discourse-cdn.com/v4/letter/j/8797f3/32.png) [@Jason\_86](https://klipper.discourse.group/u/Jason_86)\
**Post date:** [August 12, 2022, 2:51pm UTC](https://klipper.discourse.group/t/move-out-of-range/3812/6 "2022-08-12T14:51:36Z")

</div>

Thank you very much for your help~ It was working fine after I uncheck Origin at center~added new knowledge 😂 😂 😂 😂

---

<div class="post-metadata">

**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\
**Post date:** [September 4, 2024, 11:17am UTC](https://klipper.discourse.group/t/move-out-of-range/3812/7 "2024-09-04T11:17:16Z")

</div>