# Not able to print after setting up printer **URL:** \ **Category:** General Discussion\ **Created:** [February 2, 2025, 10:41pm UTC](https://klipper.discourse.group/t/not-able-to-print-after-setting-up-printer/21795 "2025-02-02T22:41:30Z")\ **Posts on this page:** 4\ **Page:** 1
**Author:** ![Strobel](https://avatars.discourse-cdn.com/v4/letter/s/c0e974/32.png) [@Strobel](https://klipper.discourse.group/u/Strobel)\ **Post date:** [February 2, 2025, 10:41pm UTC](https://klipper.discourse.group/t/not-able-to-print-after-setting-up-printer/21795/1 "2025-02-02T22:41:30Z")
### Basic Information: Printer Model: DIY Anet A8 + Ender Sprite extruder/hotend MCU / Printerboard: BTT M5P + CB1 V2.2 Host / SBC klippy.log [klippy (9).log](https://klipper.discourse.group/uploads/short-url/eSf6nlq3JCT1pnOjMW7oxX0aWu5.log) (5.1 MB) [moonraker (1).log](https://klipper.discourse.group/uploads/short-url/kUDFVPbbl5VeWYIWb7gw2Rnkkcb.log) (182.5 KB) [printer (4).cfg](https://klipper.discourse.group/uploads/short-url/6fsH8rlJJyOJCcFWUCjS9kZp5L9.cfg) (4.8 KB) Running on 12V 40A power supply _Fill out above information and_ **_in all cases attach your_ `klippy.log` _file_** (use zip to compress it, if too big). _Pasting your_ `printer.cfg` _is **not** needed_ _ **Be sure to check our “Knowledge Base” Category first. Most relevant items, e.g. error messages, are covered there** _ ### Describe your issue: …Finally I managed to install klipper to BTT Manta M5P+CB1 I have two issues though. 1. Getting this error message when it starts to print: “Move out of range: 160.000 10.000 0.200 [15.000]”. What does it mean?? And what to do to fix it? 2. When I activate pin PA4 to my FAN0 (12V) the MOSFET blows. Fan is a 12 V with right polarity (jumper is on 12V). Why is this happening? What can i do? Everything else is working on the printer. And yes I will change to a 24V 30A power supply 🙂 ) Hope someone canbring some light over these issues! ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [February 3, 2025, 7:04am UTC](https://klipper.discourse.group/t/not-able-to-print-after-setting-up-printer/21795/2 "2025-02-03T07:04:26Z")
> [@Strobel](#): > > Getting this error message when it starts to print: “Move out of range: 160.000 10.000 0.200 [15.000]”. What does it mean?? And what to do to fix it? You may read here: [Understanding X and Y Axes Limits and Homing](https://klipper.discourse.group/t/understanding-x-and-y-axes-limits-and-homing/10779/1) > [@Strobel](#): > > the MOSFET blows What do you mean by that? * * * > [@Strobel](#): > > Fan is a 12 V plus > [@Strobel](#): > > I will change to a 24V 30A You will need a new fan, also a new heater cartridge. ---
**Author:** ![Strobel](https://avatars.discourse-cdn.com/v4/letter/s/c0e974/32.png) [@Strobel](https://klipper.discourse.group/u/Strobel)\ **Post date:** [February 3, 2025, 8:21am UTC](https://klipper.discourse.group/t/not-able-to-print-after-setting-up-printer/21795/3 "2025-02-03T08:21:59Z")
Hi Eddy, Thanks for your quick reply 👍 Both fans, the hot end fan and heater fan are 12 volt. This is set by the12V jumper on the board. Regarding the heater cartridge. This one is a 24V cartridge. This way it takes ages to get hot 😊. I think I found the cause to my warning issue! I forgot to unmark the tmc2209 lines in the printer.cfg file. Will try it out later today. /Kent ---
**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\ **Post date:** [April 4, 2025, 8:22am UTC](https://klipper.discourse.group/t/not-able-to-print-after-setting-up-printer/21795/4 "2025-04-04T08:22:46Z")
This topic was automatically closed 60 days after the last reply. New replies are no longer allowed.