# Soval Sv06 plus Wont set z height no matter what i try **URL:** \ **Category:** General Discussion\ **Created:** [April 8, 2024, 1:12am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592 "2024-04-08T01:12:58Z")\ **Posts on this page:** 10\ **Page:** 1
**Author:** ![JCFPV](https://avatars.discourse-cdn.com/v4/letter/j/d2c977/32.png) [@JCFPV](https://klipper.discourse.group/u/JCFPV)\ **Post date:** [April 8, 2024, 1:12am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/1 "2024-04-08T01:12:58Z")
### Basic Information: Printer Model: Soval sv06 plus MCU / Printerboard: sovals stock board completely stock printer [my config and macros soval sv06 plus.txt](https://klipper.discourse.group/uploads/short-url/lbwTucBA163AOnLW1dYzdKKMaBh.txt) (19.3 KB) [my klippy log soval sv06 plus.txt](https://klipper.discourse.group/uploads/short-url/8SPYtxJ8e3kQm8DeNiONcrMbWAw.txt) (1.5 MB) I am having trouble setting the z height offset. Even when i set the z min from 0 to -15 and even tried setting the probe z offset from -10 to +10 to see if that would allow me to get the z height close enough to the bed. I use klipper regularly on a ender 3v2 and a Fl sun super racer but this is definitely a first. The printer starts g28 perfectly, then when calibrating the z offset it will probe the bed 2 times then move up 3mm while moving the nozzle over the probe area. Which will not allow me enough room to get the nozzle close to the bed. When i hit the 5mm threshold the printer shuts down. I get a adc out of range error, it will not reset the probe, it will not restart. I have to manually move the z steppers up to where the z probe is not triggering and it will restart perfectly. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [April 8, 2024, 6:12am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/2 "2024-04-08T06:12:32Z")
Hello @JCFPV ! It was asked for the klippy.log. Please attach it to your **next post**. If you want to provide other code snippets, please attach them as file or use the `Preformatted Text` feature of the forum editor. The way you did it, important information got lost. Also write your explanation text with punctation and paragraphs. No one knows where a sentence starts or where it ends. ---
**Author:** ![JCFPV](https://avatars.discourse-cdn.com/v4/letter/j/d2c977/32.png) [@JCFPV](https://klipper.discourse.group/u/JCFPV)\ **Post date:** [April 8, 2024, 11:43pm UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/3 "2024-04-08T23:43:40Z")
I fixed my post if you have time please look over them. And see what i am doing wrong thanks for your time. ---
**Author:** ![EddyMI3D](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/eddymi3d/32/1981_2.png) [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)\ **Post date:** [April 9, 2024, 6:12am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/4 "2024-04-09T06:12:01Z")
Did you went by this guide? [https://www.klipper3d.org/Probe\_Calibrate.html#calibrating-probe-z-offset](https://www.klipper3d.org/Probe_Calibrate.html#calibrating-probe-z-offset) ---
**Author:** ![JCFPV](https://avatars.discourse-cdn.com/v4/letter/j/d2c977/32.png) [@JCFPV](https://klipper.discourse.group/u/JCFPV)\ **Post date:** [April 9, 2024, 9:04pm UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/5 "2024-04-09T21:04:30Z")
Absolutely ---
**Author:** ![JCFPV](https://avatars.discourse-cdn.com/v4/letter/j/d2c977/32.png) [@JCFPV](https://klipper.discourse.group/u/JCFPV)\ **Post date:** [April 9, 2024, 9:07pm UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/6 "2024-04-09T21:07:06Z")
I am not having trouble doing the calibration. I am having trouble getting the nozzle close enough to the bed to set the Z offset. It probes 2 times, as it moves the nozzle over the probe point it rises about 3 1/2mm. Then enters manual leveling as i go down it hits the 5mm klipper threshold and shuts everything down. Wont reset probe or firmware. I have to manually lift until probe deactivates then restart firmware but still no Z offset set. I have tried multiple configurations and multiple probes. Also tried to disable z hop, during leveling. Klipper wouldn’t allow it. ---
**Author:** ![Sineos](https://yyz2.discourse-cdn.com/free1/user_avatar/klipper.discourse.group/sineos/32/18_2.png) [@Sineos](https://klipper.discourse.group/u/Sineos)\ **Post date:** [April 10, 2024, 5:17am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/7 "2024-04-10T05:17:59Z")
From your logs it looks like that Klipper [shuts down](https://klipper.discourse.group/t/adc-out-of-range/6643/1) due to an erroneous reading of the `mcu_temperature` ![grafik](https://global.discourse-cdn.com/free1/uploads/klipper/original/2X/3/3d33f022f8bef414f169d705ce80c5588f09fafb.png) I do not know why, but there are reports that mcu temperatures sometimes deliver strange values. Comment out: ```auto [temperature_sensor mcu_temperature] sensor_type = temperature_mcu ``` and see if it solves the issue ---
**Author:** ![JCFPV](https://avatars.discourse-cdn.com/v4/letter/j/d2c977/32.png) [@JCFPV](https://klipper.discourse.group/u/JCFPV)\ **Post date:** [April 10, 2024, 10:14am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/8 "2024-04-10T10:14:23Z")
Thank you very much i will try as soon as i get home from work. ---
**Author:** ![JCFPV](https://avatars.discourse-cdn.com/v4/letter/j/d2c977/32.png) [@JCFPV](https://klipper.discourse.group/u/JCFPV)\ **Post date:** [April 10, 2024, 11:14pm UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/9 "2024-04-10T23:14:06Z")
Yes, Thanks so much. As soon as i comment out its working fantastic and allowing me to set the z offset. THANK YOU THANK YOU VERY MUCH. ---
**Author:** ![system](https://global.discourse-cdn.com/free1/uploads/klipper/original/1X/64419bf2aac6639e6ef5cef200dcd456b0a01ac3.png) [@system](https://klipper.discourse.group/u/system)\ **Post date:** [May 11, 2024, 9:14am UTC](https://klipper.discourse.group/t/soval-sv06-plus-wont-set-z-height-no-matter-what-i-try/15592/10 "2024-05-11T09:14:12Z")
This topic was automatically closed 30 days after the last reply. New replies are no longer allowed.