# Steppers just vibrate when trying to home
**URL:** https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990
**Category:** General Discussion
**Created:** [September 23, 2024, 5:45pm UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990 "2024-09-23T17:45:59Z")
**Posts on this page:** 7
**Page:** 1
### Author:  [@seanc18](https://klipper.discourse.group/u/seanc18)
#### Post date: [September 23, 2024, 5:45pm UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/1 "2024-09-23T17:45:59Z")
### Basic Information:
Printer Model: ender3v2
MCU / Printerboard: BTT manta ez3 v1 / cb1 v2.2 , 2209 drivers
[config-20240923-124027.zip](https://klipper.discourse.group/uploads/short-url/mXMRQtqRUXFIgjAwFWunBdYkyT3.zip) (1.3 KB)
video of issue
[Hyperlink for Video of issue](https://youtube.com/shorts/VxHoxkfPXV0?feature=share)
### Describe your issue:
I have my printer- setup with klipper and mainsailos. im not getting any errors in mainsail but when i try to home a stepper motor, the stepper just vibrates.
---
### Author:  [@EddyMI3D](https://klipper.discourse.group/u/EddyMI3D)
#### Post date: [September 23, 2024, 5:51pm UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/2 "2024-09-23T17:51:38Z")
Hello @seanc18 !
Please attach the klippy.log as it was asked for.
(Deleting the lines that ask for it does not free you from it)
---
### Author:  [@LifeOfBrian](https://klipper.discourse.group/u/LifeOfBrian)
#### Post date: [September 23, 2024, 9:05pm UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/3 "2024-09-23T21:05:15Z")
It sounds like the stepper phases are not properly connected to the board.
Do you have the data sheet of the used motors and can check the pinout of the motor connector against the board connectors?
---
### Author:  [@seanc18](https://klipper.discourse.group/u/seanc18)
#### Post date: [September 24, 2024, 12:19am UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/4 "2024-09-24T00:19:41Z")
apologize i thought it was in the zip file.
[klippy (17).log](https://klipper.discourse.group/uploads/short-url/xqTPzhY31qkjJq2MXIiDYEUM21Y.log) (28.7 KB)
---
### Author:  [@seanc18](https://klipper.discourse.group/u/seanc18)
#### Post date: [September 24, 2024, 12:20am UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/5 "2024-09-24T00:20:16Z")
i did remove the max accell decell
---
### Author:  [@seanc18](https://klipper.discourse.group/u/seanc18)
#### Post date: [September 24, 2024, 7:40pm UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/6 "2024-09-24T19:40:23Z")
[klippy (18).log](https://klipper.discourse.group/uploads/short-url/nh7QHivhxTS2iEiavvZSUPmUqZU.log) (2.0 MB)
here ya go
---
### Author:  [@system](https://klipper.discourse.group/u/system)
#### Post date: [November 23, 2024, 7:40pm UTC](https://klipper.discourse.group/t/steppers-just-vibrate-when-trying-to-home/18990/7 "2024-11-23T19:40:56Z")
This topic was automatically closed 60 days after the last reply. New replies are no longer allowed.