Loaded MCU 'OPI' 111 commands (v0.10.0-620-g11dd273b / gcc: (Ubuntu 11.3.0-1ubuntu1~22.04) 11.3.0 binutils: (GNU Binutils for Ubuntu) 2.38)
MCU 'OPI' config: ADC_MAX=4095 CLOCK_FREQ=50000000 MCU=linux PCA9685_MAX=4096 PWM_MAX=32768 STATS_SUMSQ_BASE=256
Configured MCU 'OPI' (1024 moves)
===== Config file =====
[virtual_sdcard]
path = /home/pi/printer_data/gcodes

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 2000
max_accel_to_decel = 1000
max_z_velocity = 10
max_z_accel = 100
square_corner_velocity = 5.0

[input_shaper]
shaper_freq_x = 76.4
shaper_type_x = 3hump_ei
shaper_freq_y = 82.2
shaper_type_y = 2hump_ei

[bed_screws]
screw1 = 20,20
screw2 = 160,20
screw3 = 160,160
screw4 = 20,160

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud = 250000
restart_method = command

[mcu OPI]
serial = /tmp/klipper_host_mcu

[adxl345]
cs_pin = OPI:None
spi_speed = 5000000
spi_bus = spidev1.0

[resonance_tester]
accel_chip = adxl345
probe_points = 
	70, 90, 20

[temperature_sensor OrangePi]
sensor_type = temperature_host

[temperature_sensor MCU]
sensor_type = temperature_mcu

[static_digital_output display_reset]
pins = !PC6, !PD13

[gcode_arcs]
resolution = 0.05

[display_status]

[pause_resume]

[respond]

[verify_heater heater_bed]
max_error = 120
check_gain_time = 60
hysteresis = 5
heating_gain = 2

[verify_heater extruder]
max_error = 120
check_gain_time = 30
hysteresis = 5
heating_gain = 2

[output_pin BEEPER_Pin]
pin = PC5
pwm = true
value = 0
shutdown_value = 0
cycle_time = 0.001
scale = 1

[stepper_x]
step_pin = PE3
dir_pin = PE2
enable_pin = !PE4
full_steps_per_rotation = 400
microsteps = 16
rotation_distance = 40
endstop_pin = !PA15
position_endstop = -2.5
position_min = -2.5
position_max = 155
homing_speed = 50
homing_retract_dist = 0
second_homing_speed = 3

[stepper_y]
step_pin = PE0
dir_pin = !PB9
enable_pin = !PE1
full_steps_per_rotation = 400
microsteps = 16
rotation_distance = 40
endstop_pin = !PA12
position_endstop = -3
position_min = -3
position_max = 173
homing_speed = 50
homing_retract_dist = 0
second_homing_speed = 3

[stepper_z]
step_pin = PB5
dir_pin = !PB4
enable_pin = !PB8
full_steps_per_rotation = 200
microsteps = 32
rotation_distance = 8
endstop_pin = !PA11
position_endstop = 0
position_max = 200
homing_retract_dist = 5.0
second_homing_speed = 5

[tmc2209 stepper_x]
uart_pin = PA6
uart_address = 0
run_current = 0.550
stealthchop_threshold = 999999
interpolate = true
sense_resistor = 0.110

[tmc2209 stepper_y]
uart_pin = PA6
uart_address = 1
run_current = 0.9
stealthchop_threshold = 999999
interpolate = true
sense_resistor = 0.110

[tmc2209 stepper_z]
uart_pin = PA6
uart_address = 2
run_current = 1.2
stealthchop_threshold = 0
interpolate = true
sense_resistor = 0.110

[tmc2209 extruder]
uart_pin = PA6
uart_address = 3
run_current = 0.600
sense_resistor = 0.110
stealthchop_threshold = 0
interpolate = true

[thermistor Kingroon_Calibrated B3950]
temperature1 = 25.0
resistance1 = 103180.0
temperature2 = 150.0
resistance2 = 1366.2
temperature3 = 250.0
resistance3 = 168.6

[extruder]
step_pin = PD6
dir_pin = PD3
enable_pin = !PB3
full_steps_per_rotation = 200
microsteps = 32
rotation_distance = 4.75
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = PC3
sensor_type = ATC Semitec 104NT-4-R025H42G
sensor_pin = PC1
control = pid
pid_kp = 24.438
pid_ki = 2.546
pid_kd = 58.651
min_temp = 0
max_temp = 290
min_extrude_temp = 10
instantaneous_corner_velocity = 2.0
max_extrude_only_accel = 10000
max_extrude_only_distance = 150
max_extrude_only_velocity = 100
max_extrude_cross_section = 1
pressure_advance = 0.035
pressure_advance_smooth_time = 0.040

[heater_bed]
heater_pin = PA0
sensor_type = Kingroon_Calibrated B3950
sensor_pin = PC0
control = pid
pid_kp = 60.438
pid_ki = 1.092
pid_kd = 836.308
min_temp = 0
max_temp = 130

[fan]
pin = PB1
cycle_time = 0.1
kick_start_time = 0.200
hardware_pwm = false

[heater_fan my_nozzle_fan]
pin = PA3
heater = extruder
heater_temp = 50.0
fan_speed = 1.0
shutdown_speed = 1

[gcode_macro PID_Hotend]
gcode = 
	M106 S155
	PID_CALIBRATE HEATER=extruder TARGET={params.Temp|default(200)|int}
	M300 P300 S1000
	G4 S10
	M106 S0

[gcode_macro M300]
gcode = 
	{% set S = params.S|default(1000)|int %}
	{% set P = params.P|default(100)|int %}
	{% set L = 0.5 %}
	{% if S <= 0 %}
	{% set F = 1 %}
	{% set L = 0 %}
	{% elif S >= 10000 %}
	{% set F = 0 %}
	{% else %}
	{% set F = 1/S %}
	{% endif %}
	SET_PIN PIN=BEEPER_Pin VALUE={L} CYCLE_TIME={F}
	G4 P{P}
	SET_PIN PIN=BEEPER_Pin VALUE=0

[gcode_macro PARK]
gcode = 
	PAUSE

[gcode_macro M600]
description = Filament change macro
gcode = 
	{% if printer.toolhead.homed_axes != "xyz" %}
	M118 Homing
	G28
	{% endif %}
	{% if printer.extruder.can_extrude == 0 %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% if act_z > (max_z - 20.0) %}
	{% set z_safe = max_z %}
	{% else %}
	{% set z_safe = (act_z + 20.0) %}
	{% endif %}
	G91
	G1 Z{z_safe}
	G90
	G1 X0 Y0 F2100
	M118 Acquiring temperature
	M109 S200
	{% endif %}
	{% if printer.pause_resume.is_paused == 0 %}
	PAUSE
	{% endif %}
	M118 First UNLOAD, then LOAD new and RESUME when ready

[gcode_macro UNLOAD]
description = Unload filament helper
gcode = 
	{% if printer.pause_resume.is_paused == 1 %}
	{% if printer.extruder.can_extrude == 1 %}
	G91
	G1 E5 F300
	G1 E-50 F300
	G90
	{% else %}
	RESPOND TYPE=error MSG="Extrude below minimum temp"
	{% endif %}
	{% else %}
	RESPOND TYPE=error MSG="Printer must be paused"
	{% endif %}

[gcode_macro LOAD]
description = Load filament helper
gcode = 
	{% if printer.pause_resume.is_paused == 1 %}
	{% if printer.extruder.can_extrude == 1 %}
	G91
	G1 E20 F300
	G90
	{% else %}
	RESPOND TYPE=error MSG="Extrude below minimum temp"
	{% endif %}
	{% else %}
	RESPOND TYPE=error MSG="Printer must be paused"
	{% endif %}

[gcode_macro LOW_TEMP_CHECK_T]
gcode = 
	{% if printer.extruder.target != 0 %}
	{% if printer.extruder.temperature < printer.extruder.target %}
	
	M109 S{printer.extruder.target|float}
	{% endif %}
	{% else %}
	{% if printer.extruder.target < T %}
	
	M109 S{T}
	{% endif %}
	{% endif %}

[gcode_macro M900]
description = Set pressure advance
gcode = 
	SET_PRESSURE_ADVANCE ADVANCE={params.K|default(0)}

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	
	{% set x = params.X|default(10) %}
	{% set y = params.Y|default(170) %}
	{% set z = params.Z|default(20)|float %}
	{% set e = params.E|default(1) %}
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{e} F300
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F4000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	
	{% set e = params.E|default(1) %}
	G91
	G1 E{e} F300
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	{% set ENDY = printer.toolhead.axis_maximum.y|float - 10 %}
	G91
	G1    E-1 F300
	G1 Z1 E-1 F4000
	G90
	G1 X0 Y{ENDY}
	M84
	M106 S0
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X0 Y0 E-3 F300
	G1 Z20 F3000
	G90
	M84

[gcode_macro PRINT_START]
gcode = 
	G21
	G90
	M82
	M107
	
	M117 Homing...
	G28 Y0 X0 Z0
	
	M117 Heating bed...
	M190 S{params.BED_TEMP|default(58)|float}
	M117 Settling bed...
	G4 P120000
	
	M117 Heating hotend...
	M109 S{params.EXTRUDER_TEMP|default(200)|float}
	
	
	G1 Z0.2 F500
	G1 X5 Y5 F500;
	G92 E0
	G1 E2 F500
	G1 E4 X50 F3000;
	G1 Z2;
	G92 E0;
	
	M117 Printing...

[gcode_macro PRINT_END]
gcode = 
	
	{% set max_z = printer.configfile.config["stepper_z"]["position_max"]|float %}
	
	
	{% if printer.toolhead.position.z < (max_z - 2) %}
	{% set z_safe = 2.0 %}
	{% else %}
	{% set z_safe = max_z - printer.toolhead.position.z %}
	{% endif %}
	
	
	M400
	G92 E0
	G1 E-2.0 F3600
	G91
	G0 Z{z_safe} F3600
	G90
	G28 X0
	G1 Y170 F2000
	
	M104 S0
	M140 S0
	M107
	M84
	
	M300 P300 S1000
	M300 P300 S5000
	M300 P300 S1000
	
	M117 Finished!

[gcode_macro Resonance_X]
gcode = 
	TEST_RESONANCES AXIS=X

[gcode_macro Resonance_Y]
gcode = 
	TEST_RESONANCES AXIS=Y
=======================
Loaded MCU 'mcu' 94 commands (v0.10.0-225-g6e6ad7b5 / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-11+rpi1+11) 2.31.1)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=72000000 INITIAL_PINS=!PC6,!PD13 MCU=stm32f103xe PWM_MAX=255 RECEIVE_WINDOW=192 RESERVE_PINS_serial=PB11,PB10 SERIAL_BAUD=250000 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'mcu' (1024 moves)
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-I', '/home/pi/printer_data/comms/klippy.serial', '-l', '/home/pi/printer_data/logs/klippy.log', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: '5e34b450'
CPU: 4 core ARMv7 Processor rev 5 (v7l)
Python: '3.10.6 (main, Nov  2 2022, 18:53:38) [GCC 11.3.0]'
webhooks client 3023572296: '?'
=============== Log rollover at Tue Nov 15 09:26:49 2022 ===============
webhooks client 3023572296: New connection
Stats 38.8: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2202 bytes_read=5355 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002448 OPI: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=833 bytes_read=4455 bytes_retransmit=0 bytes_invalid=0 send_seq=113 receive_seq=113 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=49999889 adj=50000207  OrangePi: temp=27.6 MCU: temp=27.1 heater_bed: target=0 temp=20.7 pwm=0.000 sysload=2.30 cputime=4.433 memavail=338676 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.7 pwm=0.000
webhooks client 3023572296: Client info {'program': 'Moonraker', 'version': 'v0.7.1-764-g490d27b'}
webhooks: registering remote method 'shutdown_machine' for connection id: 3023572296
webhooks: registering remote method 'reboot_machine' for connection id: 3023572296
webhooks: registering remote method 'pause_job_queue' for connection id: 3023572296
webhooks: registering remote method 'start_job_queue' for connection id: 3023572296
Stats 39.8: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2208 bytes_read=5506 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002086 OPI: mcu_awake=0.013 mcu_task_avg=0.000087 mcu_task_stddev=0.000505 bytes_write=839 bytes_read=4487 bytes_retransmit=0 bytes_invalid=0 send_seq=114 receive_seq=114 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50000178 adj=49995209  OrangePi: temp=28.6 MCU: temp=27.2 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.30 cputime=4.504 memavail=322608 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 40.8: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2214 bytes_read=5687 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72001972 OPI: mcu_awake=0.013 mcu_task_avg=0.000087 mcu_task_stddev=0.000505 bytes_write=845 bytes_read=4503 bytes_retransmit=0 bytes_invalid=0 send_seq=115 receive_seq=115 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50000796 adj=49996959  OrangePi: temp=28.4 MCU: temp=27.1 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.28 cputime=4.529 memavail=322608 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.7 pwm=0.000
Stats 41.8: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2220 bytes_read=5853 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72001954 OPI: mcu_awake=0.013 mcu_task_avg=0.000087 mcu_task_stddev=0.000505 bytes_write=851 bytes_read=4519 bytes_retransmit=0 bytes_invalid=0 send_seq=116 receive_seq=116 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50001602 adj=49998822  OrangePi: temp=28.2 MCU: temp=27.3 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.28 cputime=4.553 memavail=334460 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 42.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000036 bytes_write=2226 bytes_read=6019 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002001 OPI: mcu_awake=0.013 mcu_task_avg=0.000087 mcu_task_stddev=0.000505 bytes_write=857 bytes_read=4535 bytes_retransmit=0 bytes_invalid=0 send_seq=117 receive_seq=117 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50001995 adj=50000823  OrangePi: temp=27.8 MCU: temp=27.3 heater_bed: target=0 temp=20.7 pwm=0.000 sysload=2.28 cputime=4.577 memavail=334400 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 43.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000036 bytes_write=2232 bytes_read=6200 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002050 OPI: mcu_awake=0.013 mcu_task_avg=0.000087 mcu_task_stddev=0.000505 bytes_write=863 bytes_read=4551 bytes_retransmit=0 bytes_invalid=0 send_seq=118 receive_seq=118 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50001910 adj=50000152  OrangePi: temp=27.7 MCU: temp=27.4 heater_bed: target=0 temp=20.7 pwm=0.000 sysload=2.28 cputime=4.601 memavail=340036 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.7 pwm=0.000
Stats 44.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000036 bytes_write=2238 bytes_read=6366 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002006 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000022 bytes_write=869 bytes_read=4580 bytes_retransmit=0 bytes_invalid=0 send_seq=119 receive_seq=119 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50002229 adj=49999935  OrangePi: temp=28.7 MCU: temp=27.3 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.28 cputime=4.634 memavail=358984 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.7 pwm=0.000
Stats 45.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000036 bytes_write=2244 bytes_read=6517 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002118 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000022 bytes_write=875 bytes_read=4596 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50002053 adj=50001112  OrangePi: temp=28.8 MCU: temp=27.3 heater_bed: target=0 temp=20.7 pwm=0.000 sysload=2.26 cputime=4.660 memavail=359124 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 46.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000022 mcu_task_stddev=0.000036 bytes_write=2250 bytes_read=6698 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.004 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002121 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000022 bytes_write=881 bytes_read=4612 bytes_retransmit=0 bytes_invalid=0 send_seq=121 receive_seq=121 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50001694 adj=50000219  OrangePi: temp=27.2 MCU: temp=27.4 heater_bed: target=0 temp=20.7 pwm=0.000 sysload=2.26 cputime=4.683 memavail=366292 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.9 pwm=0.000
Stats 47.8: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=2256 bytes_read=6878 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.004 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002140 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000022 bytes_write=887 bytes_read=4628 bytes_retransmit=0 bytes_invalid=0 send_seq=122 receive_seq=122 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50001380 adj=49999077  OrangePi: temp=24.9 MCU: temp=27.2 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.26 cputime=4.711 memavail=366228 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 48.8: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=2262 bytes_read=7029 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.004 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002249 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000022 bytes_write=893 bytes_read=4644 bytes_retransmit=0 bytes_invalid=0 send_seq=123 receive_seq=123 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50001137 adj=49998173  OrangePi: temp=23.5 MCU: temp=27.3 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.26 cputime=4.735 memavail=366228 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 49.8: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=2268 bytes_read=7210 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.004 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002243 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000019 bytes_write=899 bytes_read=4673 bytes_retransmit=0 bytes_invalid=0 send_seq=124 receive_seq=124 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50000945 adj=49997361  OrangePi: temp=22.9 MCU: temp=27.3 heater_bed: target=0 temp=20.7 pwm=0.000 sysload=2.26 cputime=4.763 memavail=366160 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 50.8: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=2274 bytes_read=7371 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.003 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002216 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000019 bytes_write=905 bytes_read=4689 bytes_retransmit=0 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50000753 adj=49997152  OrangePi: temp=23.5 MCU: temp=27.3 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.08 cputime=4.790 memavail=366160 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000
Stats 51.8: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000011 bytes_write=2280 bytes_read=7512 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.004 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=72002200 OPI: mcu_awake=0.001 mcu_task_avg=0.000015 mcu_task_stddev=0.000019 bytes_write=917 bytes_read=4721 bytes_retransmit=0 bytes_invalid=0 send_seq=127 receive_seq=127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=50000571 adj=49996972  OrangePi: temp=24.0 MCU: temp=27.4 heater_bed: target=0 temp=20.6 pwm=0.000 sysload=2.08 cputime=4.817 memavail=366164 print_time=0.016 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.8 pwm=0.000