Starting Klippy...
Args: ['/home/py/klipper/klippy/klippy.py', '/home/py/klipper_config/printer.cfg', '-I', '/tmp/printer', '-l', '/home/py/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-391-g722ad4a1'
CPU: 2 core AMD A6-4455M APU with Radeon(tm) HD Graphics
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Building C code module c_helper.so
Start printer at Mon May  2 21:14:47 2022 (1651515287.0 4500.7)
Can't read autosave from config file - modifications after header
===== Config file =====
[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{e} F2100
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	{% set e = params.E|default(1) %}
	G91
	G1 E{e} F2100
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[virtual_sdcard]
path = ~/gcode_files

[input_shaper]
shaper_freq_x = 73.4
shaper_freq_y = 31.8
shaper_type_x = mzv
shaper_type_y = mzv

[adxl345]
cs_pin = PA7

[resonance_tester]
accel_chip_x = adxl345
accel_chip_y = adxl345
probe_points = 
	100, 100, 20

[firmware_retraction]
retract_length = 0.35
retract_speed = 5
unretract_speed = 5

[stepper_x]
step_pin = PE3
dir_pin = PE2
enable_pin = !PE4
microsteps = 128
full_steps_per_rotation = 400
rotation_distance = 40
endstop_pin = !PA15
position_endstop = -10
position_min = -10
position_max = 305
homing_speed = 100

[tmc2209 stepper_x]
uart_pin = PA10
interpolate = False
run_current = 0.92

[stepper_y]
step_pin = PE0
dir_pin = !PB9
enable_pin = !PE1
microsteps = 128
rotation_distance = 40
full_steps_per_rotation = 400
endstop_pin = !PA12
position_endstop = -15
position_min = -15
position_max = 300
homing_speed = 100

[tmc2209 stepper_y]
uart_pin = PA9
interpolate = False
run_current = 0.92

[stepper_z]
step_pin = PB5
dir_pin = !PB4
enable_pin = !PB8
microsteps = 128
rotation_distance = 8
full_steps_per_rotation = 200
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -4

[tmc2209 stepper_z]
uart_pin = PC7
interpolate = False
run_current = 1.2

[extruder]
step_pin = PD6
dir_pin = !PD3
enable_pin = !PB3
microsteps = 128
rotation_distance = 3.5243297
full_steps_per_rotation = 200
nozzle_diameter = 0.400
filament_diameter = 1.750
pressure_advance = 0.06
pressure_advance_smooth_time = 0.04
max_extrude_only_distance = 700
heater_pin = PC3
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC1
smooth_time = 1
control = pid
min_extrude_temp = 180
pid_kp = 15.563
pid_ki = 0.804
pid_kd = 75.288
min_temp = 0
max_temp = 260

[tmc2209 extruder]
uart_pin = PC13
interpolate = False
run_current = 0.750
hold_current = 0.500

[heater_bed]
heater_pin = PA0
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC0
min_temp = 0
max_temp = 100
control = watermark

[homing_override]
set_position_z = 0
gcode = 
	G90
	G1 Z8
	G28 X Y
	G0 X135 Y120 F9000
	G28 Z
	G1 Z8
	G1 X0 Y0 Z5 F3000

[bed_mesh]
speed = 120
horizontal_move_z = 8
mesh_min = 45,35
mesh_max = 275, 270
probe_count = 5, 5
fade_end = 10
split_delta_z = 0.01
move_check_distance = 3
mesh_pps = 2, 2
algorithm = lagrange
relative_reference_index = 12

[screws_tilt_adjust]
screw1 = 15,1
screw1_name = front left screw
screw2 = 258,1
screw2_name = front right screw
screw3 = 258,240
screw3_name = rear right screw
screw4 = 15,240
screw4_name = rear left screw
horizontal_move_z = 8
screw_thread = CW-M3

[bltouch]
sensor_pin = ^PA11
control_pin = PA8
x_offset = -20
y_offset = 20
z_offset = 2.28
speed = 1
samples = 3
lift_speed = 5.0
samples_result = average
samples_tolerance = 0.100
samples_tolerance_retries = 2

[filament_switch_sensor filament_sensor]
switch_pin = ^PA4

[fan]
pin = PB1

[temperature_sensor mcu]
sensor_type = temperature_mcu

[temperature_sensor pi]
sensor_type = temperature_host

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud = 250000
restart_method = command

[printer]
kinematics = cartesian
max_velocity = 500
max_accel = 3500
max_z_velocity = 25
max_z_accel = 100
max_accel_to_decel = 1700

[gcode_macro RETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.retract_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.retract_speed|float %}
	{% endif %}
	SET_RETRACTION RETRACT_LENGTH={L} RETRACT_SPEED={S}

[gcode_macro UNRETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.unretract_extra_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.unretract_speed|float %}
	{% endif %}
	SET_RETRACTION UNRETRACT_EXTRA_LENGTH={S} UNRETRACT_SPEED={F}
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 139921139768784: New connection
webhooks client 139921139768784: Client info {'program': 'Moonraker', 'version': 'v0.7.1-562-gcd520ba'}
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
MCU error during connect
Traceback (most recent call last):
  File "/home/py/klipper/klippy/klippy.py", line 158, in _connect
    self.send_event("klippy:mcu_identify")
  File "/home/py/klipper/klippy/klippy.py", line 248, in send_event
    return [cb(*params) for cb in self.event_handlers.get(event, [])]
  File "/home/py/klipper/klippy/mcu.py", line 779, in _mcu_identify
    raise error(str(e))
error: mcu 'mcu': Unable to connect
No build file /home/py/klipper/klippy/../.config
No build file /home/py/klipper/klippy/../out/klipper.dict
No build file /home/py/klipper/klippy/../out/klipper.elf
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
webhooks client 139921139768784: Disconnected
webhooks client 139921139806864: New connection
webhooks client 139921139806864: Client info {'program': 'Moonraker', 'version': 'v0.7.1-562-gcd520ba'}
Unable to issue reset command on MCU 'mcu'
webhooks client 139921139806864: Disconnected
Restarting printer
Start printer at Mon May  2 21:20:20 2022 (1651515620.9 4834.6)
Can't read autosave from config file - modifications after header
===== Config file =====
[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{e} F2100
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	{% set e = params.E|default(1) %}
	G91
	G1 E{e} F2100
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[virtual_sdcard]
path = ~/gcode_files

[input_shaper]
shaper_freq_x = 73.4
shaper_freq_y = 31.8
shaper_type_x = mzv
shaper_type_y = mzv

[adxl345]
cs_pin = PA7

[resonance_tester]
accel_chip_x = adxl345
accel_chip_y = adxl345
probe_points = 
	100, 100, 20

[firmware_retraction]
retract_length = 0.35
retract_speed = 5
unretract_speed = 5

[stepper_x]
step_pin = PE3
dir_pin = PE2
enable_pin = !PE4
microsteps = 128
full_steps_per_rotation = 400
rotation_distance = 40
endstop_pin = !PA15
position_endstop = -10
position_min = -10
position_max = 305
homing_speed = 100

[tmc2209 stepper_x]
uart_pin = PA10
interpolate = False
run_current = 0.92

[stepper_y]
step_pin = PE0
dir_pin = !PB9
enable_pin = !PE1
microsteps = 128
rotation_distance = 40
full_steps_per_rotation = 400
endstop_pin = !PA12
position_endstop = -15
position_min = -15
position_max = 300
homing_speed = 100

[tmc2209 stepper_y]
uart_pin = PA9
interpolate = False
run_current = 0.92

[stepper_z]
step_pin = PB5
dir_pin = !PB4
enable_pin = !PB8
microsteps = 128
rotation_distance = 8
full_steps_per_rotation = 200
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -4

[tmc2209 stepper_z]
uart_pin = PC7
interpolate = False
run_current = 1.2

[extruder]
step_pin = PD6
dir_pin = !PD3
enable_pin = !PB3
microsteps = 128
rotation_distance = 3.5243297
full_steps_per_rotation = 200
nozzle_diameter = 0.400
filament_diameter = 1.750
pressure_advance = 0.06
pressure_advance_smooth_time = 0.04
max_extrude_only_distance = 700
heater_pin = PC3
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC1
smooth_time = 1
control = pid
min_extrude_temp = 180
pid_kp = 15.563
pid_ki = 0.804
pid_kd = 75.288
min_temp = 0
max_temp = 260

[tmc2209 extruder]
uart_pin = PC13
interpolate = False
run_current = 0.750
hold_current = 0.500

[heater_bed]
heater_pin = PA0
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC0
min_temp = 0
max_temp = 100
control = watermark

[homing_override]
set_position_z = 0
gcode = 
	G90
	G1 Z8
	G28 X Y
	G0 X135 Y120 F9000
	G28 Z
	G1 Z8
	G1 X0 Y0 Z5 F3000

[bed_mesh]
speed = 120
horizontal_move_z = 8
mesh_min = 45,35
mesh_max = 275, 270
probe_count = 5, 5
fade_end = 10
split_delta_z = 0.01
move_check_distance = 3
mesh_pps = 2, 2
algorithm = lagrange
relative_reference_index = 12

[screws_tilt_adjust]
screw1 = 15,1
screw1_name = front left screw
screw2 = 258,1
screw2_name = front right screw
screw3 = 258,240
screw3_name = rear right screw
screw4 = 15,240
screw4_name = rear left screw
horizontal_move_z = 8
screw_thread = CW-M3

[bltouch]
sensor_pin = ^PA11
control_pin = PA8
x_offset = -20
y_offset = 20
z_offset = 2.28
speed = 1
samples = 3
lift_speed = 5.0
samples_result = average
samples_tolerance = 0.100
samples_tolerance_retries = 2

[filament_switch_sensor filament_sensor]
switch_pin = ^PA4

[fan]
pin = PB1

[temperature_sensor mcu]
sensor_type = temperature_mcu

[temperature_sensor pi]
sensor_type = temperature_host

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud = 250000
restart_method = command

[printer]
kinematics = cartesian
max_velocity = 500
max_accel = 3500
max_z_velocity = 25
max_z_accel = 100
max_accel_to_decel = 1700

[gcode_macro RETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.retract_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.retract_speed|float %}
	{% endif %}
	SET_RETRACTION RETRACT_LENGTH={L} RETRACT_SPEED={S}

[gcode_macro UNRETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.unretract_extra_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.unretract_speed|float %}
	{% endif %}
	SET_RETRACTION UNRETRACT_EXTRA_LENGTH={S} UNRETRACT_SPEED={F}
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 139921139740040: New connection
webhooks client 139921139740040: Client info {'program': 'Moonraker', 'version': 'v0.7.1-562-gcd520ba'}
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
MCU error during connect
Traceback (most recent call last):
  File "/home/py/klipper/klippy/klippy.py", line 158, in _connect
    self.send_event("klippy:mcu_identify")
  File "/home/py/klipper/klippy/klippy.py", line 248, in send_event
    return [cb(*params) for cb in self.event_handlers.get(event, [])]
  File "/home/py/klipper/klippy/mcu.py", line 779, in _mcu_identify
    raise error(str(e))
error: mcu 'mcu': Unable to connect
Build file /home/py/klipper/klippy/../.config(2652): Mon May  2 21:21:13 2022
========= Last MCU build config =========
CONFIG_LOW_LEVEL_OPTIONS=y
# CONFIG_MACH_AVR is not set
# CONFIG_MACH_ATSAM is not set
# CONFIG_MACH_ATSAMD is not set
# CONFIG_MACH_LPC176X is not set
CONFIG_MACH_STM32=y
# CONFIG_MACH_RP2040 is not set
# CONFIG_MACH_PRU is not set
# CONFIG_MACH_LINUX is not set
# CONFIG_MACH_SIMU is not set
CONFIG_BOARD_DIRECTORY="stm32"
CONFIG_MCU="stm32f103xe"
CONFIG_CLOCK_FREQ=72000000
CONFIG_SERIAL=y
CONFIG_FLASH_START=0x8007000
CONFIG_FLASH_SIZE=0x10000
CONFIG_RAM_START=0x20000000
CONFIG_RAM_SIZE=0x5000
CONFIG_STACK_SIZE=512
CONFIG_STM32_SELECT=y
CONFIG_MACH_STM32F103=y
# CONFIG_MACH_STM32F207 is not set
# CONFIG_MACH_STM32F401 is not set
# CONFIG_MACH_STM32F405 is not set
# CONFIG_MACH_STM32F407 is not set
# CONFIG_MACH_STM32F429 is not set
# CONFIG_MACH_STM32F446 is not set
# CONFIG_MACH_STM32F031 is not set
# CONFIG_MACH_STM32F042 is not set
# CONFIG_MACH_STM32F070 is not set
# CONFIG_MACH_STM32F072 is not set
# CONFIG_MACH_STM32G0B1 is not set
# CONFIG_MACH_STM32H743 is not set
# CONFIG_MACH_STM32H750 is not set
CONFIG_MACH_STM32F1=y
CONFIG_HAVE_STM32_USBFS=y
CONFIG_HAVE_STM32_CANBUS=y
# CONFIG_STM32F103GD_DISABLE_SWD is not set
# CONFIG_STM32_FLASH_START_2000 is not set
# CONFIG_STM32_FLASH_START_5000 is not set
CONFIG_STM32_FLASH_START_7000=y
# CONFIG_STM32_FLASH_START_8000 is not set
# CONFIG_STM32_FLASH_START_8800 is not set
# CONFIG_STM32_FLASH_START_10000 is not set
# CONFIG_STM32_FLASH_START_800 is not set
# CONFIG_STM32_FLASH_START_4000 is not set
# CONFIG_STM32_FLASH_START_0000 is not set
CONFIG_STM32_CLOCK_REF_8M=y
# CONFIG_STM32_CLOCK_REF_12M is not set
# CONFIG_STM32_CLOCK_REF_16M is not set
# CONFIG_STM32_CLOCK_REF_25M is not set
# CONFIG_STM32_CLOCK_REF_INTERNAL is not set
CONFIG_CLOCK_REF_FREQ=8000000
CONFIG_STM32F0_TRIM=16
# CONFIG_STM32_USB_PA11_PA12 is not set
# CONFIG_STM32_SERIAL_USART1 is not set
# CONFIG_STM32_SERIAL_USART1_ALT_PB7_PB6 is not set
# CONFIG_STM32_SERIAL_USART2 is not set
# CONFIG_STM32_SERIAL_USART2_ALT_PD6_PD5 is not set
CONFIG_STM32_SERIAL_USART3=y
# CONFIG_STM32_SERIAL_USART3_ALT_PD9_PD8 is not set
# CONFIG_STM32_CANBUS_PA11_PA12 is not set
# CONFIG_STM32_CANBUS_PB8_PB9 is not set
# CONFIG_STM32_CANBUS_PD0_PD1 is not set
CONFIG_CANBUS_FREQUENCY=500000
CONFIG_SERIAL_BAUD=250000
CONFIG_USB_VENDOR_ID=0x1d50
CONFIG_USB_DEVICE_ID=0x614e
CONFIG_USB_SERIAL_NUMBER_CHIPID=y
CONFIG_USB_SERIAL_NUMBER="12345"
CONFIG_INITIAL_PINS=""
CONFIG_HAVE_GPIO=y
CONFIG_HAVE_GPIO_ADC=y
CONFIG_HAVE_GPIO_SPI=y
CONFIG_HAVE_GPIO_I2C=y
CONFIG_HAVE_GPIO_HARD_PWM=y
CONFIG_HAVE_GPIO_BITBANGING=y
CONFIG_HAVE_STRICT_TIMING=y
CONFIG_HAVE_CHIPID=y
CONFIG_HAVE_STEPPER_BOTH_EDGE=y
CONFIG_INLINE_STEPPER_HACK=y
=======================
Build file /home/py/klipper/klippy/../out/klipper.dict(7288): Mon May  2 21:21:23 2022
Last MCU build version: v0.10.0-391-g722ad4a1
Last MCU build tools: gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-12+11) 2.31.1
Last MCU build config: BUS_PINS_i2c1=PB6,PB7 RECEIVE_WINDOW=192 RESERVE_PINS_serial=PB11,PB10 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c1a=PB8,PB9 STEPPER_BOTH_EDGE=1 SERIAL_BAUD=250000 ADC_MAX=4095 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi1=PA6,PA7,PA5 PWM_MAX=255 MCU=stm32f103xe STATS_SUMSQ_BASE=256 BUS_PINS_spi1a=PB4,PB5,PB3 CLOCK_FREQ=72000000
Build file /home/py/klipper/klippy/../out/klipper.elf(271852): Mon May  2 21:21:27 2022
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
Starting Klippy...
Args: ['/home/py/klipper/klippy/klippy.py', '/home/py/klipper_config/printer.cfg', '-I', '/tmp/printer', '-l', '/home/py/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-391-g722ad4a1'
CPU: 2 core AMD A6-4455M APU with Radeon(tm) HD Graphics
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon May  2 21:23:39 2022 (1651515819.8 42.0)
Can't read autosave from config file - modifications after header
===== Config file =====
[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{e} F2100
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	{% set e = params.E|default(1) %}
	G91
	G1 E{e} F2100
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[virtual_sdcard]
path = ~/gcode_files

[input_shaper]
shaper_freq_x = 73.4
shaper_freq_y = 31.8
shaper_type_x = mzv
shaper_type_y = mzv

[adxl345]
cs_pin = PA7

[resonance_tester]
accel_chip_x = adxl345
accel_chip_y = adxl345
probe_points = 
	100, 100, 20

[firmware_retraction]
retract_length = 0.35
retract_speed = 5
unretract_speed = 5

[stepper_x]
step_pin = PE3
dir_pin = PE2
enable_pin = !PE4
microsteps = 128
full_steps_per_rotation = 400
rotation_distance = 40
endstop_pin = !PA15
position_endstop = -10
position_min = -10
position_max = 305
homing_speed = 100

[tmc2209 stepper_x]
uart_pin = PA10
interpolate = False
run_current = 0.92

[stepper_y]
step_pin = PE0
dir_pin = !PB9
enable_pin = !PE1
microsteps = 128
rotation_distance = 40
full_steps_per_rotation = 400
endstop_pin = !PA12
position_endstop = -15
position_min = -15
position_max = 300
homing_speed = 100

[tmc2209 stepper_y]
uart_pin = PA9
interpolate = False
run_current = 0.92

[stepper_z]
step_pin = PB5
dir_pin = !PB4
enable_pin = !PB8
microsteps = 128
rotation_distance = 8
full_steps_per_rotation = 200
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -4

[tmc2209 stepper_z]
uart_pin = PC7
interpolate = False
run_current = 1.2

[extruder]
step_pin = PD6
dir_pin = !PD3
enable_pin = !PB3
microsteps = 128
rotation_distance = 3.5243297
full_steps_per_rotation = 200
nozzle_diameter = 0.400
filament_diameter = 1.750
pressure_advance = 0.06
pressure_advance_smooth_time = 0.04
max_extrude_only_distance = 700
heater_pin = PC3
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC1
smooth_time = 1
control = pid
min_extrude_temp = 180
pid_kp = 15.563
pid_ki = 0.804
pid_kd = 75.288
min_temp = 0
max_temp = 260

[tmc2209 extruder]
uart_pin = PC13
interpolate = False
run_current = 0.750
hold_current = 0.500

[heater_bed]
heater_pin = PA0
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC0
min_temp = 0
max_temp = 100
control = watermark

[homing_override]
set_position_z = 0
gcode = 
	G90
	G1 Z8
	G28 X Y
	G0 X135 Y120 F9000
	G28 Z
	G1 Z8
	G1 X0 Y0 Z5 F3000

[bed_mesh]
speed = 120
horizontal_move_z = 8
mesh_min = 45,35
mesh_max = 275, 270
probe_count = 5, 5
fade_end = 10
split_delta_z = 0.01
move_check_distance = 3
mesh_pps = 2, 2
algorithm = lagrange
relative_reference_index = 12

[screws_tilt_adjust]
screw1 = 15,1
screw1_name = front left screw
screw2 = 258,1
screw2_name = front right screw
screw3 = 258,240
screw3_name = rear right screw
screw4 = 15,240
screw4_name = rear left screw
horizontal_move_z = 8
screw_thread = CW-M3

[bltouch]
sensor_pin = ^PA11
control_pin = PA8
x_offset = -20
y_offset = 20
z_offset = 2.28
speed = 1
samples = 3
lift_speed = 5.0
samples_result = average
samples_tolerance = 0.100
samples_tolerance_retries = 2

[filament_switch_sensor filament_sensor]
switch_pin = ^PA4

[fan]
pin = PB1

[temperature_sensor mcu]
sensor_type = temperature_mcu

[temperature_sensor pi]
sensor_type = temperature_host

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud = 250000
restart_method = command

[printer]
kinematics = cartesian
max_velocity = 500
max_accel = 3500
max_z_velocity = 25
max_z_accel = 100
max_accel_to_decel = 1700

[gcode_macro RETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.retract_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.retract_speed|float %}
	{% endif %}
	SET_RETRACTION RETRACT_LENGTH={L} RETRACT_SPEED={S}

[gcode_macro UNRETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.unretract_extra_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.unretract_speed|float %}
	{% endif %}
	SET_RETRACTION UNRETRACT_EXTRA_LENGTH={S} UNRETRACT_SPEED={F}
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
webhooks client 140272584797504: New connection
webhooks client 140272584797504: Client info {'program': 'Moonraker', 'version': 'v0.7.1-562-gcd520ba'}
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
Starting Klippy...
Args: ['/home/py/klipper/klippy/klippy.py', '/home/py/klipper_config/printer.cfg', '-I', '/tmp/printer', '-l', '/home/py/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-391-g722ad4a1'
CPU: 2 core AMD A6-4455M APU with Radeon(tm) HD Graphics
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon May  2 21:26:38 2022 (1651515998.9 38.1)
Can't read autosave from config file - modifications after header
===== Config file =====
[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{e} F2100
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	{% set e = params.E|default(1) %}
	G91
	G1 E{e} F2100
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[virtual_sdcard]
path = ~/gcode_files

[input_shaper]
shaper_freq_x = 73.4
shaper_freq_y = 31.8
shaper_type_x = mzv
shaper_type_y = mzv

[adxl345]
cs_pin = PA7

[resonance_tester]
accel_chip_x = adxl345
accel_chip_y = adxl345
probe_points = 
	100, 100, 20

[firmware_retraction]
retract_length = 0.35
retract_speed = 5
unretract_speed = 5

[stepper_x]
step_pin = PE3
dir_pin = PE2
enable_pin = !PE4
microsteps = 128
full_steps_per_rotation = 400
rotation_distance = 40
endstop_pin = !PA15
position_endstop = -10
position_min = -10
position_max = 305
homing_speed = 100

[tmc2209 stepper_x]
uart_pin = PA10
interpolate = False
run_current = 0.92

[stepper_y]
step_pin = PE0
dir_pin = !PB9
enable_pin = !PE1
microsteps = 128
rotation_distance = 40
full_steps_per_rotation = 400
endstop_pin = !PA12
position_endstop = -15
position_min = -15
position_max = 300
homing_speed = 100

[tmc2209 stepper_y]
uart_pin = PA9
interpolate = False
run_current = 0.92

[stepper_z]
step_pin = PB5
dir_pin = !PB4
enable_pin = !PB8
microsteps = 128
rotation_distance = 8
full_steps_per_rotation = 200
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -4

[tmc2209 stepper_z]
uart_pin = PC7
interpolate = False
run_current = 1.2

[extruder]
step_pin = PD6
dir_pin = !PD3
enable_pin = !PB3
microsteps = 128
rotation_distance = 3.5243297
full_steps_per_rotation = 200
nozzle_diameter = 0.400
filament_diameter = 1.750
pressure_advance = 0.06
pressure_advance_smooth_time = 0.04
max_extrude_only_distance = 700
heater_pin = PC3
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC1
smooth_time = 1
control = pid
min_extrude_temp = 180
pid_kp = 15.563
pid_ki = 0.804
pid_kd = 75.288
min_temp = 0
max_temp = 260

[tmc2209 extruder]
uart_pin = PC13
interpolate = False
run_current = 0.750
hold_current = 0.500

[heater_bed]
heater_pin = PA0
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC0
min_temp = 0
max_temp = 100
control = watermark

[homing_override]
set_position_z = 0
gcode = 
	G90
	G1 Z8
	G28 X Y
	G0 X135 Y120 F9000
	G28 Z
	G1 Z8
	G1 X0 Y0 Z5 F3000

[bed_mesh]
speed = 120
horizontal_move_z = 8
mesh_min = 45,35
mesh_max = 275, 270
probe_count = 5, 5
fade_end = 10
split_delta_z = 0.01
move_check_distance = 3
mesh_pps = 2, 2
algorithm = lagrange
relative_reference_index = 12

[screws_tilt_adjust]
screw1 = 15,1
screw1_name = front left screw
screw2 = 258,1
screw2_name = front right screw
screw3 = 258,240
screw3_name = rear right screw
screw4 = 15,240
screw4_name = rear left screw
horizontal_move_z = 8
screw_thread = CW-M3

[bltouch]
sensor_pin = ^PA11
control_pin = PA8
x_offset = -20
y_offset = 20
z_offset = 2.28
speed = 1
samples = 3
lift_speed = 5.0
samples_result = average
samples_tolerance = 0.100
samples_tolerance_retries = 2

[filament_switch_sensor filament_sensor]
switch_pin = ^PA4

[fan]
pin = PB1

[temperature_sensor mcu]
sensor_type = temperature_mcu

[temperature_sensor pi]
sensor_type = temperature_host

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud = 250000
restart_method = command

[printer]
kinematics = cartesian
max_velocity = 500
max_accel = 3500
max_z_velocity = 25
max_z_accel = 100
max_accel_to_decel = 1700

[gcode_macro RETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.retract_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.retract_speed|float %}
	{% endif %}
	SET_RETRACTION RETRACT_LENGTH={L} RETRACT_SPEED={S}

[gcode_macro UNRETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.unretract_extra_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.unretract_speed|float %}
	{% endif %}
	SET_RETRACTION UNRETRACT_EXTRA_LENGTH={S} UNRETRACT_SPEED={F}
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
webhooks client 140286519455040: New connection
webhooks client 140286519455040: Client info {'program': 'Moonraker', 'version': 'v0.7.1-562-gcd520ba'}
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
mcu 'mcu': Timeout on connect
MCU error during connect
Traceback (most recent call last):
  File "/home/py/klipper/klippy/klippy.py", line 158, in _connect
    self.send_event("klippy:mcu_identify")
  File "/home/py/klipper/klippy/klippy.py", line 248, in send_event
    return [cb(*params) for cb in self.event_handlers.get(event, [])]
  File "/home/py/klipper/klippy/mcu.py", line 779, in _mcu_identify
    raise error(str(e))
error: mcu 'mcu': Unable to connect
Build file /home/py/klipper/klippy/../.config(2652): Mon May  2 21:21:13 2022
========= Last MCU build config =========
CONFIG_LOW_LEVEL_OPTIONS=y
# CONFIG_MACH_AVR is not set
# CONFIG_MACH_ATSAM is not set
# CONFIG_MACH_ATSAMD is not set
# CONFIG_MACH_LPC176X is not set
CONFIG_MACH_STM32=y
# CONFIG_MACH_RP2040 is not set
# CONFIG_MACH_PRU is not set
# CONFIG_MACH_LINUX is not set
# CONFIG_MACH_SIMU is not set
CONFIG_BOARD_DIRECTORY="stm32"
CONFIG_MCU="stm32f103xe"
CONFIG_CLOCK_FREQ=72000000
CONFIG_SERIAL=y
CONFIG_FLASH_START=0x8007000
CONFIG_FLASH_SIZE=0x10000
CONFIG_RAM_START=0x20000000
CONFIG_RAM_SIZE=0x5000
CONFIG_STACK_SIZE=512
CONFIG_STM32_SELECT=y
CONFIG_MACH_STM32F103=y
# CONFIG_MACH_STM32F207 is not set
# CONFIG_MACH_STM32F401 is not set
# CONFIG_MACH_STM32F405 is not set
# CONFIG_MACH_STM32F407 is not set
# CONFIG_MACH_STM32F429 is not set
# CONFIG_MACH_STM32F446 is not set
# CONFIG_MACH_STM32F031 is not set
# CONFIG_MACH_STM32F042 is not set
# CONFIG_MACH_STM32F070 is not set
# CONFIG_MACH_STM32F072 is not set
# CONFIG_MACH_STM32G0B1 is not set
# CONFIG_MACH_STM32H743 is not set
# CONFIG_MACH_STM32H750 is not set
CONFIG_MACH_STM32F1=y
CONFIG_HAVE_STM32_USBFS=y
CONFIG_HAVE_STM32_CANBUS=y
# CONFIG_STM32F103GD_DISABLE_SWD is not set
# CONFIG_STM32_FLASH_START_2000 is not set
# CONFIG_STM32_FLASH_START_5000 is not set
CONFIG_STM32_FLASH_START_7000=y
# CONFIG_STM32_FLASH_START_8000 is not set
# CONFIG_STM32_FLASH_START_8800 is not set
# CONFIG_STM32_FLASH_START_10000 is not set
# CONFIG_STM32_FLASH_START_800 is not set
# CONFIG_STM32_FLASH_START_4000 is not set
# CONFIG_STM32_FLASH_START_0000 is not set
CONFIG_STM32_CLOCK_REF_8M=y
# CONFIG_STM32_CLOCK_REF_12M is not set
# CONFIG_STM32_CLOCK_REF_16M is not set
# CONFIG_STM32_CLOCK_REF_25M is not set
# CONFIG_STM32_CLOCK_REF_INTERNAL is not set
CONFIG_CLOCK_REF_FREQ=8000000
CONFIG_STM32F0_TRIM=16
# CONFIG_STM32_USB_PA11_PA12 is not set
# CONFIG_STM32_SERIAL_USART1 is not set
# CONFIG_STM32_SERIAL_USART1_ALT_PB7_PB6 is not set
# CONFIG_STM32_SERIAL_USART2 is not set
# CONFIG_STM32_SERIAL_USART2_ALT_PD6_PD5 is not set
CONFIG_STM32_SERIAL_USART3=y
# CONFIG_STM32_SERIAL_USART3_ALT_PD9_PD8 is not set
# CONFIG_STM32_CANBUS_PA11_PA12 is not set
# CONFIG_STM32_CANBUS_PB8_PB9 is not set
# CONFIG_STM32_CANBUS_PD0_PD1 is not set
CONFIG_CANBUS_FREQUENCY=500000
CONFIG_SERIAL_BAUD=250000
CONFIG_USB_VENDOR_ID=0x1d50
CONFIG_USB_DEVICE_ID=0x614e
CONFIG_USB_SERIAL_NUMBER_CHIPID=y
CONFIG_USB_SERIAL_NUMBER="12345"
CONFIG_INITIAL_PINS=""
CONFIG_HAVE_GPIO=y
CONFIG_HAVE_GPIO_ADC=y
CONFIG_HAVE_GPIO_SPI=y
CONFIG_HAVE_GPIO_I2C=y
CONFIG_HAVE_GPIO_HARD_PWM=y
CONFIG_HAVE_GPIO_BITBANGING=y
CONFIG_HAVE_STRICT_TIMING=y
CONFIG_HAVE_CHIPID=y
CONFIG_HAVE_STEPPER_BOTH_EDGE=y
CONFIG_INLINE_STEPPER_HACK=y
=======================
Build file /home/py/klipper/klippy/../out/klipper.dict(7288): Mon May  2 21:21:23 2022
Last MCU build version: v0.10.0-391-g722ad4a1
Last MCU build tools: gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-12+11) 2.31.1
Last MCU build config: BUS_PINS_i2c1=PB6,PB7 RECEIVE_WINDOW=192 RESERVE_PINS_serial=PB11,PB10 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c1a=PB8,PB9 STEPPER_BOTH_EDGE=1 SERIAL_BAUD=250000 ADC_MAX=4095 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi1=PA6,PA7,PA5 PWM_MAX=255 MCU=stm32f103xe STATS_SUMSQ_BASE=256 BUS_PINS_spi1a=PB4,PB5,PB3 CLOCK_FREQ=72000000
Build file /home/py/klipper/klippy/../out/klipper.elf(271852): Mon May  2 21:21:27 2022
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed
webhooks client 140286519455040: Disconnected
Restarting printer
Start printer at Mon May  2 21:30:23 2022 (1651516223.9 262.7)
Can't read autosave from config file - modifications after header
===== Config file =====
[pause_resume]

[display_status]

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{e} F2100
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	{% set e = params.E|default(1) %}
	G91
	G1 E{e} F2100
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[virtual_sdcard]
path = ~/gcode_files

[input_shaper]
shaper_freq_x = 73.4
shaper_freq_y = 31.8
shaper_type_x = mzv
shaper_type_y = mzv

[adxl345]
cs_pin = PA7

[resonance_tester]
accel_chip_x = adxl345
accel_chip_y = adxl345
probe_points = 
	100, 100, 20

[firmware_retraction]
retract_length = 0.35
retract_speed = 5
unretract_speed = 5

[stepper_x]
step_pin = PE3
dir_pin = PE2
enable_pin = !PE4
microsteps = 128
full_steps_per_rotation = 400
rotation_distance = 40
endstop_pin = !PA15
position_endstop = -10
position_min = -10
position_max = 305
homing_speed = 100

[tmc2209 stepper_x]
uart_pin = PA10
interpolate = False
run_current = 0.92

[stepper_y]
step_pin = PE0
dir_pin = !PB9
enable_pin = !PE1
microsteps = 128
rotation_distance = 40
full_steps_per_rotation = 400
endstop_pin = !PA12
position_endstop = -15
position_min = -15
position_max = 300
homing_speed = 100

[tmc2209 stepper_y]
uart_pin = PA9
interpolate = False
run_current = 0.92

[stepper_z]
step_pin = PB5
dir_pin = !PB4
enable_pin = !PB8
microsteps = 128
rotation_distance = 8
full_steps_per_rotation = 200
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -4

[tmc2209 stepper_z]
uart_pin = PC7
interpolate = False
run_current = 1.2

[extruder]
step_pin = PD6
dir_pin = !PD3
enable_pin = !PB3
microsteps = 128
rotation_distance = 3.5243297
full_steps_per_rotation = 200
nozzle_diameter = 0.400
filament_diameter = 1.750
pressure_advance = 0.06
pressure_advance_smooth_time = 0.04
max_extrude_only_distance = 700
heater_pin = PC3
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC1
smooth_time = 1
control = pid
min_extrude_temp = 180
pid_kp = 15.563
pid_ki = 0.804
pid_kd = 75.288
min_temp = 0
max_temp = 260

[tmc2209 extruder]
uart_pin = PC13
interpolate = False
run_current = 0.750
hold_current = 0.500

[heater_bed]
heater_pin = PA0
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PC0
min_temp = 0
max_temp = 100
control = watermark

[homing_override]
set_position_z = 0
gcode = 
	G90
	G1 Z8
	G28 X Y
	G0 X135 Y120 F9000
	G28 Z
	G1 Z8
	G1 X0 Y0 Z5 F3000

[bed_mesh]
speed = 120
horizontal_move_z = 8
mesh_min = 45,35
mesh_max = 275, 270
probe_count = 5, 5
fade_end = 10
split_delta_z = 0.01
move_check_distance = 3
mesh_pps = 2, 2
algorithm = lagrange
relative_reference_index = 12

[screws_tilt_adjust]
screw1 = 15,1
screw1_name = front left screw
screw2 = 258,1
screw2_name = front right screw
screw3 = 258,240
screw3_name = rear right screw
screw4 = 15,240
screw4_name = rear left screw
horizontal_move_z = 8
screw_thread = CW-M3

[bltouch]
sensor_pin = ^PA11
control_pin = PA8
x_offset = -20
y_offset = 20
z_offset = 2.28
speed = 1
samples = 3
lift_speed = 5.0
samples_result = average
samples_tolerance = 0.100
samples_tolerance_retries = 2

[filament_switch_sensor filament_sensor]
switch_pin = ^PA4

[fan]
pin = PB1

[temperature_sensor mcu]
sensor_type = temperature_mcu

[temperature_sensor pi]
sensor_type = temperature_host

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
baud = 250000
restart_method = command

[printer]
kinematics = cartesian
max_velocity = 500
max_accel = 3500
max_z_velocity = 25
max_z_accel = 100
max_accel_to_decel = 1700

[gcode_macro RETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.retract_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.retract_speed|float %}
	{% endif %}
	SET_RETRACTION RETRACT_LENGTH={L} RETRACT_SPEED={S}

[gcode_macro UNRETRACT]
gcode = 
	{% if params.L is not defined %}
	{% set L = printer.configfile.settings.firmware_retraction.unretract_extra_length|float %}
	{% endif %}
	{% if params.S is not defined %}
	{% set S = printer.configfile.settings.firmware_retraction.unretract_speed|float %}
	{% endif %}
	SET_RETRACTION UNRETRACT_EXTRA_LENGTH={S} UNRETRACT_SPEED={F}
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 140286519568144: New connection
webhooks client 140286519568144: Client info {'program': 'Moonraker', 'version': 'v0.7.1-562-gcd520ba'}
mcu 'mcu': Timeout on connect
mcu 'mcu': Wait for identify_response
Traceback (most recent call last):
  File "/home/py/klipper/klippy/serialhdl.py", line 69, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/py/klipper/klippy/serialhdl.py", line 258, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 316, in get_response
    cmd_queue)
  File "/home/py/klipper/klippy/serialhdl.py", line 250, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/py/klipper/klippy/serialhdl.py", line 62, in _error
    raise error(self.warn_prefix + (msg % params))
error: mcu 'mcu': Serial connection closed