===== Config file =====
[respond]
[gcode_macro CHOPPER_TUNE]
description = Vibrations tests to calculate lowest magnitude drivers registers v1.2
variable_debug = False
variable_inset = 10
variable_current_change_step = 25
variable_measure_time = 1250
variable_required_rpm = [37.5, 150, 1.5]
variable_delay = 500
variable_fclk = 12
gcode =
{% set current_min = params.CURRENT_MIN_MA|default('default')|string|lower %}
{% set current_max = params.CURRENT_MAX_MA|default('default')|string|lower %}
{% set tbl_min = params.TBL_MIN|default(0)|int %}
{% set tbl_max = params.TBL_MAX|default(3)|int %}
{% set toff_min = params.TOFF_MIN|default(1)|int %}
{% set toff_max = params.TOFF_MAX|default(8)|int %}
{% set hstrt_hend_max = params.HSTRT_HEND_MAX|default(16)|int %}
{% set hstrt_min = params.HSTRT_MIN|default(0)|int %}
{% set hstrt_max = params.HSTRT_MAX|default(7)|int %}
{% set hend_min = params.HEND_MIN|default(2)|int %}
{% set hend_max = params.HEND_MAX|default(15)|int %}
{% set tpfd_min = params.TPFD_MIN|default(-1)|int %}
{% set tpfd_max = params.TPFD_MAX|default(-1)|int %}
{% set min_speed = params.MIN_SPEED|default('default')|string|lower %}
{% set max_speed = params.MAX_SPEED|default('default')|string|lower %}
{% set speed_change_step = params.SPEED_CHANGE_STEP|default('default')|string|lower %}
{% set iterations = params.ITERATIONS|default(1)|int %}
{% set travel_distance = params.TRAVEL_DISTANCE|default('default')|string|lower %}
{% set accel_chip = params.ACCELEROMETER|default('default')|string|lower %}
{% set find_vibr = params.FIND_VIBRATIONS|default('False')|string|lower %}
{% set axis = params.AXIS|default('X')|string|lower %}
{% set run_plotter = params.RUN_PLOTTER|default('True')|string|lower %}
_detect_driver stepper={axis}
_chop_workflow axis={axis} {rawparams}
[gcode_shell_command chop_tune]
command = ~/chopper-resonance-tuner/chopper_plot.sh
timeout = 9999.0
verbose = True
[gcode_macro _detect_driver]
description = Find which driver is used in configuration
variable_drivers = '2130', '2208', '2209', '2660', '2240', '5160'
variable_driver = 0
variable_resistor = 0
gcode =
{% set stepper = 'stepper_' + params.STEPPER|string|lower %}
{% for driver in drivers %}
{% if 'run_current' in printer.configfile.config['tmc' + driver + ' ' + stepper] %}
{action_respond_info('Selected tmc%s for %s' % (driver, stepper))}
SET_GCODE_VARIABLE MACRO=_detect_driver VARIABLE=driver VALUE={driver}
{% if driver != '2240' %}
{% set resistor = printer.configfile.settings['tmc' + driver + ' ' + stepper].sense_resistor %}
{% else %}
{% set resistor = printer.configfile.settings['tmc' + driver + ' ' + stepper].rref %}
{% endif %}
SET_GCODE_VARIABLE MACRO=_detect_driver VARIABLE=resistor VALUE={resistor}
{% endif %}
{% endfor %}
[gcode_macro _chop_apply_regs]
variable_registers = 'tbl', 'toff', 'hend', 'hstrt', 'tpfd', 'curr'
variable_amount = 0
variable_tbl = -1
variable_toff = -1
variable_hend = -1
variable_hstrt = -1
variable_tpfd = -1
variable_curr = -1
gcode =
{% if printer['gcode_macro _chop_apply_regs'][params.FIELD]|int != params.VALUE|int %}
{% for stepper in params.STEPPERS.split('-') %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
M118 Setting {params.FIELD|string|lower} from {
printer['gcode_macro _chop_apply_regs'][params.FIELD]|int} to {params.VALUE|int} on {stepper}
{% endif %}
{% if params.FIELD|lower != 'curr' %}
SET_TMC_FIELD STEPPER={stepper} FIELD={params.FIELD} VALUE={params.VALUE|int}
{% else %}
SET_TMC_CURRENT STEPPER={stepper} CURRENT={params.VALUE|int / 1000}
{% endif %}
{% for count in range(1, amount + 1) %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
M118 Setting {params.FIELD|string|lower} from {
printer['gcode_macro _chop_apply_regs'][params.FIELD]|int} to {
params.VALUE|int} on {stepper|string + count|string}
{% endif %}
{% if params.FIELD|lower != 'curr' %}
SET_TMC_FIELD STEPPER={stepper|string + count|string} FIELD={params.FIELD} VALUE={params.VALUE|int}
{% else %}
SET_TMC_CURRENT STEPPER={stepper} CURRENT={params.VALUE|int / 1000}
{% endif %}
{% endfor %}
{% endfor %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE={params.FIELD|string|lower} VALUE={params.VALUE|int}
{% endif %}
[gcode_macro _chop_workflow]
description = Calculate process of CHOPPER_TUNE macro
gcode =
{% set axis = params.AXIS|default('X')|string|lower %}
{% set driver = printer['gcode_macro _detect_driver'].driver|string|lower %}
{% set sense_resistor = printer['gcode_macro _detect_driver'].resistor %}
{% set current_min = params.CURRENT_MIN_MA|default('default')|string|lower %}
{% set current_max = params.CURRENT_MAX_MA|default('default')|string|lower %}
{% set current_change_step = printer['gcode_macro CHOPPER_TUNE'].current_change_step %}
{% set tbl_min = params.TBL_MIN|default(0)|int %}
{% set tbl_max = params.TBL_MAX|default(3)|int %}
{% set toff_min = params.TOFF_MIN|default(1)|int %}
{% set toff_max = params.TOFF_MAX|default(8)|int %}
{% set hstrt_hend_max = params.HSTRT_HEND_MAX|default(16)|int %}
{% set hstrt_min = params.HSTRT_MIN|default(0)|int %}
{% set hstrt_max = params.HSTRT_MAX|default(7)|int %}
{% set hend_min = params.HEND_MIN|default(2)|int %}
{% set hend_max = params.HEND_MAX|default(15)|int %}
{% set tpfd_min = params.TPFD_MIN|default(-1)|int %}
{% set tpfd_max = params.TPFD_MAX|default(-1)|int %}
{% set min_speed = params.MIN_SPEED|default('default')|string|lower %}
{% set max_speed = params.MAX_SPEED|default('default')|string|lower %}
{% set speed_change_step = params.SPEED_CHANGE_STEP|default('default')|string|lower %}
{% set required_rpm = printer['gcode_macro CHOPPER_TUNE'].required_rpm %}
{% set iterations = params.ITERATIONS|default(1)|int %}
{% set travel_distance = params.TRAVEL_DISTANCE|default('default')|string|lower %}
{% set accel_chip = params.ACCELEROMETER|default('default')|string|lower %}
{% set find_vibr = params.FIND_VIBRATIONS|default('False')|string|lower %}
{% set run_plotter = params.RUN_PLOTTER|default('True')|string|lower %}
{% set inset = printer['gcode_macro CHOPPER_TUNE'].inset %}
{% set config = printer.configfile.config %}
{% set settings = printer.configfile.settings %}
{% set measure_time = printer['gcode_macro CHOPPER_TUNE'].measure_time / 1000|float %}
{% set delay = printer['gcode_macro CHOPPER_TUNE'].delay|int %}
{% set fclk = printer['gcode_macro CHOPPER_TUNE'].fclk|int %}
{% set kinematics = config.printer.kinematics|string %}
{% if axis in ['x', 'y', 'z'] %}
{% if kinematics == 'corexy' %}
{% if axis in ['x', 'y'] %}
{% if axis == 'x' %}
{% set axes = ['x', 'y'] %}
{% elif axis == 'y' %}
{% set axes = ['y', 'x'] %}
{% endif %}
{% set steppers = ['stepper_x', 'stepper_y'] %}
{% elif axis == 'z' %}
{% set axes = ['z', 'x'] %}
{% set steppers = ['stepper_z'] %}
{% endif %}
{% elif kinematics == 'cartesian' %}
{% if axis == 'x' %}
{% set axes = ['x', 'y'] %}
{% set steppers = ['stepper_x'] %}
{% elif axis == 'y' %}
{% set axes = ['y', 'x'] %}
{% set steppers = ['stepper_y'] %}
{% elif axis == 'z' %}
{% set axes = ['z', 'x'] %}
{% set steppers = ['stepper_z'] %}
{% endif %}
{% else %}
{action_raise_error('WARNING!!! Script does not support your kinematics')}
{% endif %}
{% if axes[0] == 'z' %}
{% set minAX = (settings['stepper_' + axes[0]].position_min|float, 0)|max + inset %}
{% set acceleration = settings.printer.max_z_accel|int %}
{% set trv_speed = config.printer.max_z_velocity|int / 2 * 60 %}
{% else %}
{% set minAX = settings['stepper_' + axes[0]].position_min|float + inset %}
{% set acceleration = config.printer.max_accel|int %}
{% set trv_speed = config.printer.max_velocity|int / 2 * 60 %}
{% endif %}
{% set maxAX = settings['stepper_' + axes[0]].position_max|float - inset %}
{% set midAX = settings['stepper_' + axes[0]].position_min|float +
((settings['stepper_' + axes[0]].position_max|float -
settings['stepper_' + axes[0]].position_min|float) / 2) %}
{% set midBAX = settings['stepper_' + axes[1]].position_min|float +
((settings['stepper_' + axes[1]].position_max|float -
settings['stepper_' + axes[1]].position_min|float) / 2) %}
{% else %}
{action_raise_error('WARNING!!! Incorrect direction')}
{% endif %}
{% if tpfd_min != -1 or tpfd_max != -1 %}
{% if driver == '5160' or driver == '2240' %}
{% if tpfd_min < 0 or tpfd_max < 0 %}
{action_raise_error('WARNING!!! Incorrect TPFD values')}
{% endif %}
{% else %}
{action_raise_error('WARNING!!! TMC%s not support register TPFD' % (driver))}
{% endif %}
{% endif %}
{% for register in printer['gcode_macro _chop_apply_regs'].registers %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE={register|string|lower} VALUE=-1
{% endfor %}
{% for mot in range(8) %}
{% if ('stepper_' + axes[0] + mot|string) in config %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE=amount VALUE={mot}
{% if ('stepper_' + axes[0] + (mot + 1)|string) not in config %}
{action_respond_info('Selected %dwd configuration' % (mot + 1))}
{% endif %}
{% elif mot == 1 %}
{action_respond_info('Selected 1wd configuration')}
{% endif %}
{% endfor %}
{% if accel_chip == 'default' %}
{% if 'accel_chip' in config.resonance_tester %}
{% set accel_chip = config.resonance_tester.accel_chip %}
{% else %}
{% set accel_chip = 'adxl345' %}
{% endif %}
{% endif %}
{action_respond_info('Selected %s for accelerometer' % (accel_chip))}
{% if current_min == 'default' %}
{% set current_min = (config['tmc' + driver + ' ' + steppers[0]].run_current|float * 1000)|int %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Set default run_current: %d mA to run_current_min' % (current_min))}
{% endif %}
{% else %}
{% set current_min = current_min|int %}
{% endif %}
{% if current_max == 'default' %}
{% set current_max = (config['tmc' + driver + ' ' + steppers[0]].run_current|float * 1000)|int%}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Set default run_current: %d mA to run_current_max' % (current_max))}
{% endif %}
{% else %}
{% set current_max = current_max|int %}
{% endif %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{% set current_max = current_min %}
{% set tbl_min = settings['tmc' + driver + ' ' + steppers[0]].driver_tbl|int %}
{% set tbl_max = tbl_min %}
{% set toff_min = settings['tmc' + driver + ' ' + steppers[0]].driver_toff|int %}
{% set toff_max = toff_min %}
{% set hstrt_min = settings['tmc' + driver + ' ' + steppers[0]].driver_hstrt|int %}
{% set hstrt_max = hstrt_min %}
{% set hend_min = settings['tmc' + driver + ' ' + steppers[0]].driver_hend|int %}
{% set hend_max = hend_min %}
{% set rotation_dist = config[steppers[0]].rotation_distance|float %}
{% set gear_ratio = (config[steppers[0]].gear_ratio|default('1:1')).split(':') %}
{% set full_steps_per_rotation = config[steppers[0]].full_steps_per_rotation|default(200)|int %}
{% if min_speed == 'default' %}
{% set min_speed = (required_rpm[0] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist)|float %}
{% else %}
{% set min_speed = min_speed|float %}
{% endif %}
{% if max_speed == 'default' %}
{% set max_required_mms = (required_rpm[1] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist)|int %}
{% set max_speed = (((-acceleration * measure_time + ((acceleration * measure_time) ** 2 +
4 * acceleration * (maxAX - minAX)) ** 0.5) / 2), max_required_mms)|min|float %}
{% else %}
{% set max_speed = max_speed|float %}
{% endif %}
{% if speed_change_step == 'default' %}
{% set speed_change_step = required_rpm[2] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist %}
{% else %}
{% set speed_change_step = speed_change_step|float %}
{% endif %}
{% else %}
{% if min_speed == 'default' or max_speed == 'default' %}
{action_raise_error('WARNING!!! Resonance speed must be defined')}
{% endif %}
{% set min_speed, max_speed = min_speed|float, max_speed|float %}
{% set speed_change_step = 1 %}
{% endif %}
{% if max_speed > trv_speed / 30 %}
{action_raise_error('WARNING!!! Required speed (%d mm/s) on axis (%s)'
' is faster than kinematics allow, please lower speed or increase'
' speed limit in printer.cfg' % (max_speed, axes[0]))}
{% endif %}
{% set accel_decel_distance = max_speed ** 2 / acceleration %}
{% set auto_travel_distance = accel_decel_distance + (max_speed * measure_time) %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Acceleration & deceleration zone = %f mm' % (accel_decel_distance))}
{action_respond_info('Auto calculated min required travel distance = %f mm' % (auto_travel_distance))}
{% endif %}
{% if travel_distance == 'default' %}
{% if minAX + auto_travel_distance > maxAX %}
{action_raise_error('WARNING!!! Required travel distance on axis (%s)'
' (%.2f mm) is longer than kinematics allows, please lower'
' speed or increase acceleration' % (axes[0], auto_travel_distance))}
{% endif %}
{% set travel_distance = auto_travel_distance %}
{% else %}
{% set travel_distance = travel_distance|int %}
{% if minAX + travel_distance > maxAX %}
{% set travel_distance = maxAX - minAX %}
{% if travel_distance < auto_travel_distance %}
{action_raise_error('WARNING!!! Travel distance on axis (%s) is less than'
' it should be, please increase acceleration or lower speed' % (axes[0]))}
{% else %}
{action_respond_info('WARNING!!! Travel distance on axis (%s)'
' is longer than kinematics allows, lowering...' % (axes[0]))}
{% endif %}
{% else %}
{% if travel_distance < auto_travel_distance %}
{% set travel_distance = auto_travel_distance %}
{% if minAX + auto_travel_distance > maxAX %}
{action_raise_error('WARNING!!! Travel distance on axis (%s) is less'
' than required (%.2f mm), and longer than kinematics allows, please lower'
' speed or increase acceleration' % (axes[0], auto_travel_distance))}
{% endif %}
{% endif %}
{% endif %}
{% endif %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{action_respond_info('Final max travel distance = %.2f mm, position min = %.2f, traveling: %.2f --> %.2f' %
(travel_distance, minAX, minAX, travel_distance + minAX))}
{action_respond_info('Start find vibration mode, speed: %.2f --> %.2f mm/s with %.2f step current=%d TBL=%d TOFF=%d'
' HSTRT=%d HEND=%d' % (min_speed, max_speed, speed_change_step, current_min, tbl_min, toff_min, hstrt_min, hend_min))}
{% else %}
{action_respond_info('Final travel distance = %.2f mm, position min = %.2f, traveling: %.2f --> %.2f' %
(travel_distance, minAX, minAX, travel_distance + minAX))}
{action_respond_info('Start of register enumeration mode, speed: %.2f --> %.2f mm/s current: %d'
' --> %d mA iterations=%d TBL: %d --> %d TOFF: %d --> %d HSTRT: %d --> %d HEND: %d --> %d TPFD:'
' %d --> %d' % (min_speed, max_speed, current_min, current_max, iterations, tbl_min, tbl_max,
toff_min, toff_max, hstrt_min, hstrt_max, hend_min, hend_max, tpfd_min, tpfd_max))}
{% endif %}
{% if not 'xyz' in printer.toolhead.homed_axes %}
G28 X Y Z
{% endif %}
SET_VELOCITY_LIMIT ACCEL={acceleration}
SET_VELOCITY_LIMIT ACCEL_TO_DECEL={acceleration}
G0 {axes[0]}{minAX} {axes[1]}{midBAX} F{trv_speed}
RUN_SHELL_COMMAND CMD=chop_tune PARAMS='cleaner'
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME=stand_still
G4 P5000
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME=stand_still
{% for current in range(current_min, current_max + 1, current_change_step) %}
_chop_apply_regs steppers={steppers|join('-')} field=curr value={current}
{% for tbl in range(tbl_min, tbl_max + 1) %}
_chop_apply_regs steppers={steppers|join('-')} field=tbl value={tbl}
{% for toff in range(toff_min, toff_max + 1) %}
_chop_apply_regs steppers={steppers|join('-')} field=toff value={toff}
{% for hstrt_value in range(hstrt_min, hstrt_max + 1) %}
{% for hend_value in range(hend_min, hend_max + 1) %}
{% if hend_value + hstrt_value <= hstrt_hend_max %}
_chop_apply_regs steppers={steppers|join('-')} field=hend value={hend_value}
_chop_apply_regs steppers={steppers|join('-')} field=hstrt value={hstrt_value}
{% for tpfd in range(tpfd_min, tpfd_max + 1) %}
{% if tpfd_min != -1 and tpfd_max != -1 %}
_chop_apply_regs steppers={steppers|join('-')} field=tpfd value={tpfd}
{% endif %}
DUMP_TMC STEPPER={steppers[0]} REGISTER=chopconf
{% set freq = 1/(2*(12+32*toff)*1/(1000000*fclk)+2*1/(1000000*fclk)*16*(1.5**tbl)) %}
{% for speed in range((min_speed * 100)|int, (max_speed * 100)|int + 1, (speed_change_step * 100)|int) %}
{% set speed = speed / 100 %}
{% for i in range(iterations) %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{% set travel_distance = (travel_distance / max_speed) * speed %}
G4 P{delay}
M118 Speed {speed|round(2)} mm/s on {travel_distance|round(2)} mm
{% endif %}
{% set name = '__%d_%d_%d_%d_%d_%d_%d_%d_%d__' %
(current, tbl, toff, hstrt_value, hend_value, tpfd, speed*100, freq, i+1) %}
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME={name}
G0 {axes[0]}{minAX + travel_distance} F{speed*60}
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME={name}
G0 {axes[0]}{minAX} F{trv_speed}
M400
{% endfor %}
{% endfor %}
{% endfor %}
{% endif %}
{% endfor %}
{% endfor %}
{% endfor %}
{% endfor %}
{% endfor %}
{% if tpfd_min == -1 or tpfd_max == -1 %}
{% set tpfd_min, tpfd_max = 0, 0 %}
{% endif %}
G4 P500
G0 {axis}{midAX} F{trv_speed}
{% if run_plotter == 'true' or run_plotter == '1' %}
M118 Magnitude graphs generation...
M118 This may take a while, please wait
RUN_SHELL_COMMAND CMD=chop_tune PARAMS='{'iterations=%d driver=%s sense_resistor=%f'%(iterations, driver, sense_resistor)}'
{% endif %}
M118 For run parser manually type - RUN_SHELL_COMMAND CMD=chop_tune PARAMS='{'iterations=%d driver=%s sense_resistor=%f'%
(iterations, driver, sense_resistor)}'
[virtual_sdcard]
path = ~/printer_data/gcodes
on_error_gcode = CANCEL_PRINT
[pause_resume]
[display_status]
[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = BASE_CANCEL_PRINT
gcode =
TURN_OFF_HEATERS
CLEAR_PAUSE
SDCARD_RESET_FILE
BASE_CANCEL_PRINT
G90
G0 X350 Y350 F3600
SET_SKEW CLEAR=1
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=0
[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set idle_timeout = client.idle_timeout|default(0) %}
{% set temp = printer[printer.toolhead.extruder].target if printer.toolhead.extruder != '' else 0 %}
{% set restore = False if printer.toolhead.extruder == ''
else True if params.RESTORE|default(1)|int == 1 else False %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=last_extruder_temp VALUE="{{'restore': restore, 'temp': temp}}"
{% if idle_timeout > 0 %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=restore_idle_timeout VALUE={printer.configfile.settings.idle_timeout.timeout}
SET_IDLE_TIMEOUT TIMEOUT={idle_timeout}
{% endif %}
PAUSE_BASE
{client.user_pause_macro|default("")}
_TOOLHEAD_PARK_PAUSE_CANCEL {rawparams}
[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
variable_last_extruder_temp = {'restore': False, 'temp': 0}
variable_restore_idle_timeout = 0
variable_idle_state = False
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set sp_move = client.speed_move|default(velocity) %}
{% set runout_resume = True if client.runout_sensor|default("") == ""
else True if not printer[client.runout_sensor].enabled
else printer[client.runout_sensor].filament_detected %}
{% set can_extrude = True if printer.toolhead.extruder == ''
else printer[printer.toolhead.extruder].can_extrude %}
{% set do_resume = False %}
{% set prompt_txt = [] %}
{% if printer.idle_timeout.state|upper == "IDLE" or idle_state %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=idle_state VALUE=False
{% if last_extruder_temp.restore %}
RESPOND TYPE=echo MSG='{"Restoring \"%s\" temperature to %3.1f\u00B0C, this may take some time" % (printer.toolhead.extruder, last_extruder_temp.temp) }'
M109 S{last_extruder_temp.temp}
{% set do_resume = True %}
{% elif can_extrude %}
{% set do_resume = True %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}'
{% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %}
{% endif %}
{% elif can_extrude %}
{% set do_resume = True %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}'
{% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %}
{% endif %}
{% if runout_resume %}
{% if do_resume %}
{% if restore_idle_timeout > 0 %} SET_IDLE_TIMEOUT TIMEOUT={restore_idle_timeout} {% endif %}
{client.user_resume_macro|default("")}
_CLIENT_EXTRUDE
RESUME_BASE VELOCITY={params.VELOCITY|default(sp_move)}
{% endif %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]}'
{% set _d = prompt_txt.append("\"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]) %}
{% endif %}
{% if not (runout_resume and do_resume) %}
RESPOND TYPE=command MSG="action:prompt_begin RESUME aborted !!!"
{% for element in prompt_txt %}
RESPOND TYPE=command MSG='{"action:prompt_text %s" % element}'
{% endfor %}
RESPOND TYPE=command MSG="action:prompt_footer_button Ok|RESPOND TYPE=command MSG=action:prompt_end|info"
RESPOND TYPE=command MSG="action:prompt_show"
{% endif %}
[gcode_macro SET_PAUSE_NEXT_LAYER]
description = Enable a pause if the next layer is reached
gcode =
{% set pause_next_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_next_layer %}
{% set ENABLE = params.ENABLE|default(1)|int != 0 %}
{% set MACRO = params.MACRO|default(pause_next_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_next_layer VALUE="{{ 'enable': ENABLE, 'call': MACRO }}"
[gcode_macro SET_PAUSE_AT_LAYER]
description = Enable/disable a pause if a given layer number is reached
gcode =
{% set pause_at_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_at_layer %}
{% set ENABLE = params.ENABLE|int != 0 if params.ENABLE is defined
else params.LAYER is defined %}
{% set LAYER = params.LAYER|default(pause_at_layer.layer)|int %}
{% set MACRO = params.MACRO|default(pause_at_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_at_layer VALUE="{{ 'enable': ENABLE, 'layer': LAYER, 'call': MACRO }}"
[gcode_macro SET_PRINT_STATS_INFO]
rename_existing = SET_PRINT_STATS_INFO_BASE
description = Overwrite, to get pause_next_layer and pause_at_layer feature
variable_pause_next_layer = { 'enable': False, 'call': "PAUSE" }
variable_pause_at_layer = { 'enable': False, 'layer': 0, 'call': "PAUSE" }
gcode =
{% if pause_next_layer.enable %}
RESPOND TYPE=echo MSG='{"%s, forced by pause_next_layer" % pause_next_layer.call}'
{pause_next_layer.call}
SET_PAUSE_NEXT_LAYER ENABLE=0
{% elif pause_at_layer.enable and params.CURRENT_LAYER is defined and params.CURRENT_LAYER|int == pause_at_layer.layer %}
RESPOND TYPE=echo MSG='{"%s, forced by pause_at_layer [%d]" % (pause_at_layer.call, pause_at_layer.layer)}'
{pause_at_layer.call}
SET_PAUSE_AT_LAYER ENABLE=0
{% endif %}
SET_PRINT_STATS_INFO_BASE {rawparams}
[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL]
description = Helper: park toolhead used in PAUSE and CANCEL_PRINT
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set use_custom = client.use_custom_pos|default(false)|lower == 'true' %}
{% set custom_park_x = client.custom_park_x|default(0.0) %}
{% set custom_park_y = client.custom_park_y|default(0.0) %}
{% set park_dz = client.custom_park_dz|default(2.0)|abs %}
{% set sp_hop = client.speed_hop|default(15) * 60 %}
{% set sp_move = client.speed_move|default(velocity) * 60 %}
{% set origin = printer.gcode_move.homing_origin %}
{% set act = printer.gcode_move.gcode_position %}
{% set max = printer.toolhead.axis_maximum %}
{% set cone = printer.toolhead.cone_start_z|default(max.z) %}
{% set round_bed = True if printer.configfile.settings.printer.kinematics is in ['delta','polar','rotary_delta','winch']
else False %}
{% set z_min = params.Z_MIN|default(0)|float %}
{% set z_park = [[(act.z + park_dz), z_min]|max, (max.z - origin.z)]|min %}
{% set x_park = params.X if params.X is defined
else custom_park_x if use_custom
else 0.0 if round_bed
else (max.x - 5.0) %}
{% set y_park = params.Y if params.Y is defined
else custom_park_y if use_custom
else (max.y - 5.0) if round_bed and z_park < cone
else 0.0 if round_bed
else (max.y - 5.0) %}
_CLIENT_RETRACT
{% if "xyz" in printer.toolhead.homed_axes %}
G90
G1 Z{z_park} F{sp_hop}
G1 X{x_park} Y{y_park} F{sp_move}
{% if not printer.gcode_move.absolute_coordinates %} G91 {% endif %}
{% else %}
RESPOND TYPE=echo MSG='Printer not homed'
{% endif %}
[gcode_macro _CLIENT_EXTRUDE]
description = Extrudes, if the extruder is hot enough
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set use_fw_retract = (client.use_fw_retract|default(false)|lower == 'true') and (printer.firmware_retraction is defined) %}
{% set length = params.LENGTH|default(client.unretract)|default(1.0)|float %}
{% set speed = params.SPEED|default(client.speed_unretract)|default(35) %}
{% set absolute_extrude = printer.gcode_move.absolute_extrude %}
{% if printer.toolhead.extruder != '' %}
{% if printer[printer.toolhead.extruder].can_extrude %}
{% if use_fw_retract %}
{% if length < 0 %}
G10
{% else %}
G11
{% endif %}
{% else %}
M83
G1 E{length} F{(speed|float|abs) * 60}
{% if absolute_extrude %}
M82
{% endif %}
{% endif %}
{% else %}
RESPOND TYPE=echo MSG='{"\"%s\" not hot enough" % printer.toolhead.extruder}'
{% endif %}
{% endif %}
[gcode_macro _CLIENT_RETRACT]
description = Retracts, if the extruder is hot enough
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set length = params.LENGTH|default(client.retract)|default(1.0)|float %}
{% set speed = params.SPEED|default(client.speed_retract)|default(35) %}
_CLIENT_EXTRUDE LENGTH=-{length|float|abs} SPEED={speed|float|abs}
[autotune_tmc stepper_x]
motor = omc-17me15-1504s
tuning_goal = performance
voltage = 48
tbl = 0
toff = 1
[autotune_tmc stepper_y]
motor = omc-17me15-1504s
tuning_goal = performance
voltage = 48
tbl = 0
toff = 1
[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE
gcode =
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set bed_mesh_min = printer.configfile.settings.bed_mesh.mesh_min %}
{% set bed_mesh_max = printer.configfile.settings.bed_mesh.mesh_max %}
{% set probe_count = printer.configfile.settings.bed_mesh.probe_count %}
{% set kamp_settings = printer["gcode_macro _KAMP_Settings"] %}
{% set verbose_enable = kamp_settings.verbose_enable | abs %}
{% set probe_dock_enable = kamp_settings.probe_dock_enable | abs %}
{% set attach_macro = kamp_settings.attach_macro | string %}
{% set detach_macro = kamp_settings.detach_macro | string %}
{% set mesh_margin = kamp_settings.mesh_margin | float %}
{% set fuzz_amount = kamp_settings.fuzz_amount | float %}
{% set probe_count = probe_count if probe_count|length > 1 else probe_count * 2 %}
{% set max_probe_point_distance_x = ( bed_mesh_max[0] - bed_mesh_min[0] ) / (probe_count[0] - 1) %}
{% set max_probe_point_distance_y = ( bed_mesh_max[1] - bed_mesh_min[1] ) / (probe_count[1] - 1) %}
{% set x_min = all_points | map(attribute=0) | min | default(bed_mesh_min[0]) %}
{% set y_min = all_points | map(attribute=1) | min | default(bed_mesh_min[1]) %}
{% set x_max = all_points | map(attribute=0) | max | default(bed_mesh_max[0]) %}
{% set y_max = all_points | map(attribute=1) | max | default(bed_mesh_max[1]) %}
{% set fuzz_range = range((0) | int, (fuzz_amount * 100) | int + 1) %}
{% set adapted_x_min = x_min - mesh_margin - (fuzz_range | random / 100.0) %}
{% set adapted_y_min = y_min - mesh_margin - (fuzz_range | random / 100.0) %}
{% set adapted_x_max = x_max + mesh_margin + (fuzz_range | random / 100.0) %}
{% set adapted_y_max = y_max + mesh_margin + (fuzz_range | random / 100.0) %}
{% set adapted_x_min = [adapted_x_min , bed_mesh_min[0]] | max %}
{% set adapted_y_min = [adapted_y_min , bed_mesh_min[1]] | max %}
{% set adapted_x_max = [adapted_x_max , bed_mesh_max[0]] | min %}
{% set adapted_y_max = [adapted_y_max , bed_mesh_max[1]] | min %}
{% set points_x = (((adapted_x_max - adapted_x_min) / max_probe_point_distance_x) | round(method='ceil') | int) + 1 %}
{% set points_y = (((adapted_y_max - adapted_y_min) / max_probe_point_distance_y) | round(method='ceil') | int) + 1 %}
{% if (([points_x, points_y]|max) > 6) %}
{% set algorithm = "bicubic" %}
{% set min_points = 4 %}
{% else %}
{% set algorithm = "lagrange" %}
{% set min_points = 3 %}
{% endif %}
{% set points_x = [points_x , min_points]|max %}
{% set points_y = [points_y , min_points]|max %}
{% set points_x = [points_x , probe_count[0]]|min %}
{% set points_y = [points_y , probe_count[1]]|min %}
{% if verbose_enable == True %}
{% if printer.exclude_object.objects != [] %}
{ action_respond_info( "Algorithm: {}.".format(
(algorithm),
)) }
{ action_respond_info("Default probe count: {},{}.".format(
(probe_count[0]),
(probe_count[1]),
)) }
{ action_respond_info("Adapted probe count: {},{}.".format(
(points_x),
(points_y),
)) }
{action_respond_info("Default mesh bounds: {}, {}.".format(
(bed_mesh_min[0],bed_mesh_min[1]),
(bed_mesh_max[0],bed_mesh_max[1]),
)) }
{% if mesh_margin > 0 %}
{action_respond_info("Mesh margin is {}, mesh bounds extended by {}mm.".format(
(mesh_margin),
(mesh_margin),
)) }
{% else %}
{action_respond_info("Mesh margin is 0, margin not increased.")}
{% endif %}
{% if fuzz_amount > 0 %}
{action_respond_info("Mesh point fuzzing enabled, points fuzzed up to {}mm.".format(
(fuzz_amount),
)) }
{% else %}
{action_respond_info("Fuzz amount is 0, mesh points not fuzzed.")}
{% endif %}
{ action_respond_info("Adapted mesh bounds: {}, {}.".format(
(adapted_x_min, adapted_y_min),
(adapted_x_max, adapted_y_max),
)) }
{action_respond_info("KAMP adjustments successful. Happy KAMPing!")}
{% else %}
{action_respond_info("No objects detected! Check your gcode and make sure that EXCLUDE_OBJECT_DEFINE is happening before BED_MESH_CALIBRATE is called. Defaulting to regular meshing.")}
G4 P5000
{% endif %}
{% endif %}
{% if probe_dock_enable == True %}
{attach_macro}
{% endif %}
_BED_MESH_CALIBRATE mesh_min={adapted_x_min},{adapted_y_min} mesh_max={adapted_x_max},{adapted_y_max} ALGORITHM={algorithm} PROBE_COUNT={points_x},{points_y}
{% if probe_dock_enable == True %}
{detach_macro}
{% endif %}
[gcode_macro LINE_PURGE]
description = A purge macro that adapts to be near your actual printed objects
gcode =
{% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
{% set cross_section = printer.configfile.settings.extruder.max_extrude_cross_section | float %}
{% if printer.firmware_retraction is defined %}
{% set RETRACT = G10 | string %}
{% set UNRETRACT = G11 | string %}
{% else %}
{% set RETRACT = 'G1 E-.5 F2100' | string %}
{% set UNRETRACT = 'G1 E.5 F2100' | string %}
{% endif %}
{% set verbose_enable = printer["gcode_macro _KAMP_Settings"].verbose_enable | abs %}
{% set purge_height = printer["gcode_macro _KAMP_Settings"].purge_height | float %}
{% set tip_distance = printer["gcode_macro _KAMP_Settings"].tip_distance | float %}
{% set purge_margin = printer["gcode_macro _KAMP_Settings"].purge_margin | float %}
{% set purge_amount = printer["gcode_macro _KAMP_Settings"].purge_amount | float %}
{% set flow_rate = printer["gcode_macro _KAMP_Settings"].flow_rate | float %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set purge_x_min = (all_points | map(attribute=0) | min | default(0)) %}
{% set purge_x_max = (all_points | map(attribute=0) | max | default(0)) %}
{% set purge_y_min = (all_points | map(attribute=1) | min | default(0)) %}
{% set purge_y_max = (all_points | map(attribute=1) | max | default(0)) %}
{% set purge_x_center = ([((purge_x_max + purge_x_min) / 2) - (purge_amount / 2), 0] | max) %}
{% set purge_y_center = ([((purge_y_max + purge_y_min) / 2) - (purge_amount / 2), 0] | max) %}
{% set purge_x_origin = ([purge_x_min - purge_margin, 0] | max) %}
{% set purge_y_origin = ([purge_y_min - purge_margin, 0] | max) %}
{% set purge_move_speed = (flow_rate / 5.0) * 60 | float %}
{% if cross_section < 5 %}
{action_respond_info("[Extruder] max_extrude_cross_section is insufficient for purge, please set it to 5 or greater. Purge skipped.")}
{% else %}
{% if verbose_enable == True %}
{action_respond_info("Moving filament tip {}mms".format(
(tip_distance),
)) }
{% endif %}
{% if printer.firmware_retraction is defined %}
{action_respond_info("KAMP purge is using firmware retraction.")}
{% else %}
{action_respond_info("KAMP purge is not using firmware retraction, it is recommended to configure it.")}
{% endif %}
{% if purge_y_origin > 0 %}
{action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm3/s.".format(
(purge_x_center),
(purge_y_origin),
(purge_amount),
(flow_rate),
)) }
{% else %}
{action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm3/s.".format(
(purge_x_origin),
(purge_y_center),
(purge_amount),
(flow_rate),
)) }
{% endif %}
SAVE_GCODE_STATE NAME=Prepurge_State
{% if purge_y_origin > 0 %}
G92 E0
G0 F{travel_speed}
G90
G0 X{purge_x_center} Y{purge_y_origin}
G0 Z{purge_height}
M83
G1 E{tip_distance} F{purge_move_speed}
G1 X{purge_x_center + purge_amount} E{purge_amount} F{purge_move_speed}
{RETRACT}
G0 X{purge_x_center + purge_amount + 10} F{travel_speed}
G92 E0
M82
G0 Z{purge_height * 2} F{travel_speed}
{% else %}
G92 E0
G0 F{travel_speed}
G90
G0 X{purge_x_origin} Y{purge_y_center}
G0 Z{purge_height}
M83
G1 E{tip_distance} F{purge_move_speed}
G1 Y{purge_y_center + purge_amount} E{purge_amount} F{purge_move_speed}
{RETRACT}
G0 Y{purge_y_center + purge_amount + 10} F{travel_speed}
G92 E0
M82
G0 Z{purge_height * 2} F{travel_speed}
{% endif %}
RESTORE_GCODE_STATE NAME=Prepurge_State
{% endif %}
[gcode_macro SMART_PARK]
description = Parks your printhead near the print area for pre-print hotend heating.
gcode =
{% set kamp_settings = printer["gcode_macro _KAMP_Settings"] %}
{% set z_height = kamp_settings.smart_park_height | float %}
{% set purge_margin = kamp_settings.purge_margin | float %}
{% set verbose_enable = kamp_settings.verbose_enable | abs %}
{% set center_x = printer.toolhead.axis_maximum.x / 2 | float %}
{% set center_y = printer.toolhead.axis_maximum.y / 2 | float %}
{% set axis_minimum_x = printer.toolhead.axis_minimum.x | float %}
{% set axis_minimum_y = printer.toolhead.axis_minimum.y | float %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set x_min = all_points | map(attribute=0) | min | default(center_x) %}
{% set y_min = all_points | map(attribute=1) | min | default(center_y) %}
{% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
{% if purge_margin > 0 and x_min != center_x and y_min != center_y %}
{% set x_min = [ x_min - purge_margin , x_min ] | min %}
{% set y_min = [ y_min - purge_margin , y_min ] | min %}
{% set x_min = [ x_min , axis_minimum_x ] | max %}
{% set y_min = [ y_min , axis_minimum_y ] | max %}
{% endif %}
{% if verbose_enable == True %}
{ action_respond_info("Smart Park location: {},{}.".format(
(x_min),
(y_min),
)) }
{% endif %}
SAVE_GCODE_STATE NAME=Presmartpark_State
G90
{% if printer.toolhead.position.z < z_height %}
G0 Z{z_height}
{% endif %}
G0 X{x_min} Y{y_min} F{travel_speed}
G0 Z{z_height}
RESTORE_GCODE_STATE NAME=Presmartpark_State
[gcode_macro _KAMP_Settings]
description = This macro contains all adjustable settings for KAMP
variable_verbose_enable = True
variable_mesh_margin = 5
variable_fuzz_amount = 0
variable_probe_dock_enable = False
variable_attach_macro = 'Attach_Probe'
variable_detach_macro = 'Dock_Probe'
variable_purge_height = 0.8
variable_tip_distance = 0
variable_purge_margin = 10
variable_purge_amount = 30
variable_flow_rate = 12
variable_smart_park_height = 10
gcode =
{action_respond_info(" Running the KAMP_Settings macro does nothing, it is only used for storing KAMP settings. ")}
[gcode_macro _TAP_VARIABLES]
variable_probing = 0
variable_brushed = 0
gcode =
[gcode_macro _PRE_PROBE_CHECK]
gcode =
{% set svv = printer.save_variables.variables %}
{% set PROBE_TEMP = svv.probe_temp %}
{% set MAX_TEMP = PROBE_TEMP + 5 %}
{% set ACTUAL_TEMP = printer.extruder.temperature %}
{% set TARGET_TEMP = printer.extruder.target %}
{% set PROBE_ACCEL = printer["gcode_macro _TAP_SETTINGS"].probe_accel %}
{% set BRUSHED = printer["gcode_macro _TAP_VARIABLES"].brushed %}
{% if BRUSHED == 1 %}
_PROBE_TEMP_CHECK
{% else %}
NOZZLE_BRUSH
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=1
_PROBE_TEMP_CHECK
{% endif %}
[gcode_macro _PROBE_TEMP_CHECK]
gcode =
{% set svv = printer.save_variables.variables %}
{% set PROBE_TEMP = svv.probe_temp %}
{% set MAX_TEMP = PROBE_TEMP + 5 %}
{% set ACTUAL_TEMP = printer.extruder.temperature %}
{% set TARGET_TEMP = printer.extruder.target %}
{% set PROBE_ACCEL = printer["gcode_macro _TAP_SETTINGS"].probe_accel %}
SET_KINEMATICS_LIMIT Z_ACCEL={PROBE_ACCEL}
{% if TARGET_TEMP > PROBE_TEMP %}
{ action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
M109 S{PROBE_TEMP}
{% else %}
{% if ACTUAL_TEMP > MAX_TEMP %}
{ action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={MAX_TEMP}
{% endif %}
{% endif %}
[gcode_macro _POST_PROBING]
gcode =
SET_KINEMATICS_LIMIT Z_ACCEL={printer["gcode_macro _TAP_SETTINGS"].max_z_accel}
[gcode_macro _POST_PROBE]
gcode =
POST_PROBE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
[gcode_macro SET_PROBE_TEMP]
gcode =
{% set temp = params.TEMP|int %}
SAVE_VARIABLE VARIABLE=probe_temp VALUE={TEMP}
[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_REAL
gcode =
Z_TILT_ADJUST_REAL
POST_PROBE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
[gcode_macro _TAP_SETTINGS]
variable_probe_accel = 15
variable_home_x = 175
variable_home_y = 175
variable_home_speed = 100
variable_max_z_accel = 30
gcode =
[mcu]
serial = /dev/serial/by-id/usb-Klipper_stm32f446xx_JKYZ-if00
[danger_options]
allow_plugin_override = True
[printer]
square_corner_velocity = 500.0
kinematics = limited_corexy
max_velocity = 564
max_z_velocity = 30
max_accel = 20000
max_x_accel = 20000
max_y_accel = 19000
max_z_accel = 30
scale_xy_accel = True
[thermistor NTC10K]
temperature1 = 0.0
resistance1 = 32116.0
temperature2 = 40.0
resistance2 = 5309.0
temperature3 = 80.0
resistance3 = 1228.0
[stepper_y]
step_pin = PE11
dir_pin = PE10
enable_pin = !PE9
rotation_distance = 40
microsteps = 32
full_steps_per_rotation = 200
endstop_pin = PB13
position_min = 0
position_endstop = 350
position_max = 350
homing_speed = 60
homing_retract_dist = 0
homing_positive_dir = true
step_pulse_duration = 0.000004
[tmc5160 stepper_y]
cs_pin = PE7
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = true
run_current = 1.3
sense_resistor = 0.033
driver_tbl = 0
driver_toff = 1
driver_hstrt = 0
driver_hend = 10
driver_tpfd = 1
[stepper_x]
step_pin = PD8
dir_pin = PB12
enable_pin = !PD9
rotation_distance = 40
microsteps = 32
full_steps_per_rotation = 200
endstop_pin = PB14
position_min = 0
step_pulse_duration = 0.000004
position_endstop = 350
position_max = 350
homing_speed = 60
homing_retract_dist = 0
homing_positive_dir = true
[tmc5160 stepper_x]
cs_pin = PE15
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = true
run_current = 1.3
sense_resistor = 0.033
driver_tbl = 0
driver_toff = 1
driver_hstrt = 0
driver_hend = 10
driver_tpfd = 1
[stepper_z]
step_pin = PE2
dir_pin = PE4
enable_pin = !PE3
rotation_distance = 4
microsteps = 32
endstop_pin = probe:z_virtual_endstop
position_max = 290
position_min = -5
homing_speed = 50
second_homing_speed = 10
homing_retract_dist = 3
[tmc2209 stepper_z]
uart_pin = PC15
uart_address = 0
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[stepper_z1]
step_pin = PE1
dir_pin = PE0
enable_pin = !PC5
rotation_distance = 4
microsteps = 32
[tmc2209 stepper_z1]
uart_pin = PD11
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[stepper_z2]
step_pin = PD12
dir_pin = PC4
enable_pin = !PE8
rotation_distance = 4
microsteps = 32
[tmc2209 stepper_z2]
uart_pin = PA15
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[extruder]
step_pin = PE6
dir_pin = !PC13
enable_pin = !PE5
rotation_distance = 4.637
microsteps = 16
full_steps_per_rotation = 200
nozzle_diameter = 0.600
filament_diameter = 1.75
heater_pin = PB15
sensor_type = PT1000
sensor_pin = PC0
min_temp = 10
max_temp = 315
max_power = 1.0
min_extrude_temp = 170
heater_power = 65
cooling_fan = fan_generic fan0
ambient_temp_sensor = heater_generic chamber_heater
pressure_advance = 0.05
pressure_advance_smooth_time = 0.040
max_extrude_cross_section = 5
pid_version = 1
pid_target = 285.00
pid_tolerance = 0.0200
pid_kp = 18.086
pid_ki = 0.536
pid_kd = 152.599
control = mpc
block_heat_capacity = 16.6237
sensor_responsiveness = 0.0731558
ambient_transfer = 0.110661
fan_ambient_transfer = 0.110661, 0.194043, 0.24027
[tmc5160 extruder]
cs_pin = PC14
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = True
run_current = 0.5
hold_current = 0.5
sense_resistor = 0.033
[verify_heater extruder]
hysteresis = 20
heating_gain = 0.2
check_gain_time = 120
[heater_bed]
heater_pin = PB3
sensor_type = Generic 3950
sensor_pin = PC1
max_power = 0.8
min_temp = 5
max_temp = 170
pid_version = 1
pid_target = 105.00
pid_tolerance = 0.0200
control = pid
pid_kp = 51.427
pid_ki = 1.894
pid_kd = 349.061
[probe]
pin = PA3
x_offset = 0
y_offset = 0
speed = 50.0
samples = 4
samples_result = median
sample_retract_dist = 3.0
samples_tolerance = 0.1
samples_tolerance_retries = 5
deactivate_on_each_sample = True
activate_gcode =
_PRE_PROBE_CHECK
deactivate_gcode =
_POST_PROBING
z_offset = -1.930
[safe_z_home]
home_xy_position = 175, 175
z_hop = 5
[heater_fan hotend_fan]
pin = PA13
max_power = 1.0
kick_start_time = 0.5
heater = extruder
heater_temp = 50.0
fan_speed = 1.0
[fan_generic fan0]
pin = PA8
max_power = 1.0
kick_start_time = 0.1
off_below = 0.05
cycle_time = 0.00005
[idle_timeout]
timeout = 9999999999
[bed_mesh]
speed = 100
horizontal_move_z = 10
mesh_min = 40, 40
mesh_max = 310,310
fade_start = 0.6
fade_end = 10.0
probe_count = 7,7
algorithm = bicubic
adaptive_margin = 5
[z_tilt]
z_positions =
-50, 18
150, 348
350, 18
points =
30, 5
175, 295
320, 5
speed = 100
horizontal_move_z = 10
retries = 10
retry_tolerance = 0.007
[gcode_macro G32]
gcode =
BED_MESH_CLEAR
G28
Z_TILT_ADJUST
G28
G0 X175 Y175 Z30 F3600
[save_variables]
filename = ~/printer_data/config/variables.cfg
[gcode_macro _PREHEAT]
gcode =
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={printer.extruder.filament.extruder}
SET_HEATER_TEMPERATURE HEATER=bed TARGET={printer.extruder.filament.bed}
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={printer.extruder.filament.chamber}
[gcode_macro _COOLOFF]
gcode =
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=0
SET_HEATER_TEMPERATURE HEATER=bed TARGET=0
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
SET_FAN_SPEED FAN=fan2 SPEED=1.0
[gcode_macro PRINT_START]
gcode =
{% set chamber = printer.extruder.filament.chamber %}
SET_FAN_SPEED FAN=fan0 SPEED=0.0
SET_FAN_SPEED FAN=fan2 SPEED=0.0
G28
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={printer.extruder.filament.chamber}
TEMPERATURE_WAIT SENSOR="heater_generic chamber_heater" MINIMUM={printer.extruder.filament.chamber}
SET_HEATER_TEMPERATURE HEATER=chamber_heater target=0
G28 Z
BED_MESH_CALIBRATE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
G92 E0
G90
LINE_PURGE
[gcode_macro PRINT_END]
gcode =
M400
G92 E0
G1 E-1.0 F3600
G91
G0 Z1.00 X20.0 Y20.0 F20000
TURN_OFF_HEATERS
M107
G90
G0 X350 Y350 F3600
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=0
[exclude_object]
[gcode_arcs]
resolution = 0.1
[input_shaper]
smoother_freq_x = 56.6
smoother_freq_y = 30.8
shaper_type_x = smooth_zvd_ei
shaper_freq_x = 41.6
shaper_type_y = smooth_ei
shaper_freq_y = 26.6
[filaments]
on_set_filament_gcode =
M117 add
on_clear_filament_gcode =
M117 clear
[z_thermal_adjust]
temp_coeff = 0.005
smooth_time = 1
sensor_type = NTC10K
sensor_pin = PB0
min_temp = 10
max_temp = 77
gcode_id = thermal_adjust
[led led_strip]
red_pin = PB6
green_pin = PB5
blue_pin = PB7
[heater_generic chamber_heater]
heater_pin = PC8
max_power = 1.0
sensor_type = Generic 3950
sensor_pin = PB1
min_temp = 10
max_temp = 75
pid_version = 1
pid_target = 60.00
pid_tolerance = 0.0200
control = pid
pid_kp = 64.228
pid_ki = 0.421
pid_kd = 2450.039
[heater_fan chamber_heater_fan]
pin = PB2
max_power = 1.0
heater = chamber_heater
heater_temp = 35
[verify_heater chamber_heater]
hysteresis = 10
heating_gain = 0.1
check_gain_time = 600
[fan_generic fan2]
pin = !PD1
cycle_time = 0.00005
kick_start_time = 0.1
off_below = 0.07
[gcode_macro M106]
gcode =
{% set fan = 'fan' + (params.P|int if params.P is defined else 0)|string %}
{% set speed = (params.S|float / 255 if params.S is defined else 1.0) %}
SET_FAN_SPEED FAN={fan} SPEED={speed}
[gcode_macro _ENABLE_FAN]
variable_fan_on = 0
gcode =
{% if printer["gcode_macro _ENABLE_FAN"].fan_on == 0 %}
SET_FAN_SPEED FAN=fan0 SPEED={printer.extruder.filament.part_cooling}
SET_FAN_SPEED FAN=fan2 SPEED={printer.extruder.filament.aux_cooling}
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=1
{% endif %}
[skew_correction]
[pid_profile extruder abs]
pid_version = 1
pid_target = 260.00
pid_tolerance = 0.0200
control = pid
pid_kp = 16.100
pid_ki = 1.058
pid_kd = 61.259
[pid_profile heater_bed abs]
pid_version = 1
pid_target = 105.00
pid_tolerance = 0.0200
control = pid
pid_kp = 51.427
pid_ki = 1.894
pid_kd = 349.061
[skew_correction skew]
xy_skew = 0.000
xz_skew = 0.000
yz_skew = 0.000
[pid_profile extruder pc]
pid_version = 1
pid_target = 250.00
pid_tolerance = 0.0200
control = pid
pid_kp = 17.627
pid_ki = 1.013
pid_kd = 76.678
[bed_mesh default]
version = 1
points =
-0.080000, 0.003125, 0.086875
-0.013438, 0.047187, 0.126875
0.057187, 0.112812, 0.140312
x_count = 3
y_count = 3
mesh_x_pps = 2
mesh_y_pps = 2
algo = lagrange
tension = 0.2
min_x = 161.25
max_x = 188.75
min_y = 161.25
max_y = 188.75
[cpap_heater]
pid_version = 1
pid_target = 40.00
pid_tolerance = 0.0200
control = pid
pid_kp = 8.528
pid_ki = 0.070
pid_kd = 260.544
=======================
Loaded MCU 'mcu' 105 commands ( v0.10.0-557-gf7e29b27 / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-12+11) 2.31.1)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c3=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 CLOCK_FREQ=180000000 MCU=stm32f446xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'mcu' (1024 moves)
Args: ['/home/orangepi/klipper/klippy/klippy.py', '/home/orangepi/printer_data/config/printer.cfg', '-I', '/home/orangepi/printer_data/comms/klippy.serial', '-l', '/home/orangepi/printer_data/logs/klippy.log', '-a', '/home/orangepi/printer_data/comms/klippy.sock']
App Name: Danger-Klipper
Git version: 'v0.12.0-551-gaf6bdd39'
Branch: bleeding-edge-v2
Remote: origin
Tracked URL: https://github.com/DangerKlippers/danger-klipper
CPU: 4 core ?
Python: '3.10.12 (main, Sep 11 2024, 15:47:36) [GCC 11.4.0]'
webhooks client 548336828720: {'program': 'Moonraker', 'version': 'v0.9.3-1-g4e00a07'}
=============== Log rollover at Wed Jan 29 14:33:22 2025 ===============
Stats 257298.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844838 bytes_read=13303119 bytes_retransmit=9 bytes_invalid=0 send_seq=95775 receive_seq=95775 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004187 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.06 cputime=10458.610 memavail=3557652 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=22.4 pwm=1.000
Heater extruder approaching new target of 220.000
Stats 257299.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844860 bytes_read=13303361 bytes_retransmit=9 bytes_invalid=0 send_seq=95777 receive_seq=95777 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004291 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.06 cputime=10458.649 memavail=3557780 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=22.7 pwm=1.000
Stats 257300.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844866 bytes_read=13303568 bytes_retransmit=9 bytes_invalid=0 send_seq=95778 receive_seq=95778 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004267 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.06 cputime=10458.674 memavail=3557716 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=23.3 pwm=1.000
Stats 257301.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844872 bytes_read=13303776 bytes_retransmit=9 bytes_invalid=0 send_seq=95779 receive_seq=95779 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004199 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.06 cputime=10458.711 memavail=3557684 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=24.4 pwm=1.000
Stats 257302.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844894 bytes_read=13304004 bytes_retransmit=9 bytes_invalid=0 send_seq=95781 receive_seq=95781 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004259 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.06 cputime=10458.737 memavail=3557812 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=26.1 pwm=1.000
Stats 257303.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844900 bytes_read=13304211 bytes_retransmit=9 bytes_invalid=0 send_seq=95782 receive_seq=95782 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004193 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10458.775 memavail=3557684 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=29.1 pwm=1.000
Stats 257304.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844906 bytes_read=13304433 bytes_retransmit=9 bytes_invalid=0 send_seq=95783 receive_seq=95783 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004275 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.05 cputime=10458.812 memavail=3557716 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=31.8 pwm=1.000
Stats 257305.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844912 bytes_read=13304656 bytes_retransmit=9 bytes_invalid=0 send_seq=95784 receive_seq=95784 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004292 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10458.836 memavail=3557732 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=34.9 pwm=1.000
Stats 257306.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844934 bytes_read=13304868 bytes_retransmit=9 bytes_invalid=0 send_seq=95786 receive_seq=95786 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004412 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10458.877 memavail=3557732 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=39.5 pwm=1.000
Stats 257307.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844940 bytes_read=13305076 bytes_retransmit=9 bytes_invalid=0 send_seq=95787 receive_seq=95787 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004381 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10458.914 memavail=3557764 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=43.3 pwm=1.000
Stats 257308.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844946 bytes_read=13305299 bytes_retransmit=9 bytes_invalid=0 send_seq=95788 receive_seq=95788 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004467 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10458.938 memavail=3557700 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=47.0 pwm=1.000
Stats 257309.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844952 bytes_read=13305520 bytes_retransmit=9 bytes_invalid=0 send_seq=95789 receive_seq=95789 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004448 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10458.976 memavail=3557636 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=52.4 pwm=1.000
Stats 257310.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844958 bytes_read=13305743 bytes_retransmit=9 bytes_invalid=0 send_seq=95790 receive_seq=95790 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004499 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10459.017 memavail=3557764 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=56.6 pwm=1.000
Stats 257311.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844980 bytes_read=13305956 bytes_retransmit=9 bytes_invalid=0 send_seq=95792 receive_seq=95792 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004410 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10459.040 memavail=3557700 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=60.7 pwm=1.000
Stats 257312.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844986 bytes_read=13306158 bytes_retransmit=9 bytes_invalid=0 send_seq=95793 receive_seq=95793 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004354 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.05 cputime=10459.077 memavail=3557796 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=66.4 pwm=1.000
Stats 257313.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844992 bytes_read=13306366 bytes_retransmit=9 bytes_invalid=0 send_seq=95794 receive_seq=95794 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004297 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.04 cputime=10459.122 memavail=3557700 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=70.6 pwm=1.000
Stats 257314.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=844998 bytes_read=13306586 bytes_retransmit=9 bytes_invalid=0 send_seq=95795 receive_seq=95795 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004336 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.04 cputime=10459.146 memavail=3557732 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=74.7 pwm=1.000
Stats 257315.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845020 bytes_read=13306798 bytes_retransmit=9 bytes_invalid=0 send_seq=95797 receive_seq=95797 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004338 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.04 cputime=10459.181 memavail=3557732 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=80.4 pwm=1.000
Stats 257316.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845026 bytes_read=13307021 bytes_retransmit=9 bytes_invalid=0 send_seq=95798 receive_seq=95798 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004253 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.04 cputime=10459.220 memavail=3557864 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=84.4 pwm=1.000
Stats 257317.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845032 bytes_read=13307229 bytes_retransmit=9 bytes_invalid=0 send_seq=95799 receive_seq=95799 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004326 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.04 cputime=10459.244 memavail=3557608 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=88.5 pwm=1.000
Stats 257318.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845038 bytes_read=13307436 bytes_retransmit=9 bytes_invalid=0 send_seq=95800 receive_seq=95800 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004413 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.12 cputime=10459.281 memavail=3557768 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=94.1 pwm=1.000
Stats 257319.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845060 bytes_read=13307678 bytes_retransmit=9 bytes_invalid=0 send_seq=95802 receive_seq=95802 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004391 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.12 cputime=10459.323 memavail=3557736 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=98.3 pwm=1.000
Stats 257320.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845066 bytes_read=13307886 bytes_retransmit=9 bytes_invalid=0 send_seq=95803 receive_seq=95803 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004430 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.12 cputime=10459.348 memavail=3557736 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=102.3 pwm=1.000
Stats 257321.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845072 bytes_read=13308093 bytes_retransmit=9 bytes_invalid=0 send_seq=95804 receive_seq=95804 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004420 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.12 cputime=10459.384 memavail=3557832 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=107.8 pwm=1.000
Stats 257322.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845078 bytes_read=13308316 bytes_retransmit=9 bytes_invalid=0 send_seq=95805 receive_seq=95805 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004337 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.12 cputime=10459.425 memavail=3557708 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=111.5 pwm=1.000
Stats 257323.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845100 bytes_read=13308529 bytes_retransmit=9 bytes_invalid=0 send_seq=95807 receive_seq=95807 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004289 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.11 cputime=10459.449 memavail=3557772 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=115.7 pwm=1.000
Stats 257324.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845106 bytes_read=13308750 bytes_retransmit=9 bytes_invalid=0 send_seq=95808 receive_seq=95808 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004253 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.11 cputime=10459.486 memavail=3557772 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=120.9 pwm=1.000
Stats 257325.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845112 bytes_read=13308973 bytes_retransmit=9 bytes_invalid=0 send_seq=95809 receive_seq=95809 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004276 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.11 cputime=10459.527 memavail=3557712 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=124.8 pwm=1.000
Stats 257326.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845118 bytes_read=13309181 bytes_retransmit=9 bytes_invalid=0 send_seq=95810 receive_seq=95810 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004248 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.11 cputime=10459.551 memavail=3557648 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=128.4 pwm=1.000
Stats 257327.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845140 bytes_read=13309393 bytes_retransmit=9 bytes_invalid=0 send_seq=95812 receive_seq=95812 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004224 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.11 cputime=10459.584 memavail=3558060 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=133.5 pwm=1.000
Stats 257328.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845152 bytes_read=13309632 bytes_retransmit=9 bytes_invalid=0 send_seq=95814 receive_seq=95814 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004391 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.10 cputime=10459.627 memavail=3557868 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=137.1 pwm=1.000
Stats 257329.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845158 bytes_read=13309854 bytes_retransmit=9 bytes_invalid=0 send_seq=95815 receive_seq=95815 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004368 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.10 cputime=10459.651 memavail=3557964 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=140.8 pwm=1.000
Stats 257330.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845164 bytes_read=13310061 bytes_retransmit=9 bytes_invalid=0 send_seq=95816 receive_seq=95816 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004314 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.10 cputime=10459.689 memavail=3558028 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=145.7 pwm=1.000
Stats 257331.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845170 bytes_read=13310284 bytes_retransmit=9 bytes_invalid=0 send_seq=95817 receive_seq=95817 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004346 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.10 cputime=10459.730 memavail=3557996 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=149.4 pwm=1.000
Stats 257332.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845192 bytes_read=13310497 bytes_retransmit=9 bytes_invalid=0 send_seq=95819 receive_seq=95819 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004385 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.10 cputime=10459.753 memavail=3557964 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=153.0 pwm=1.000
Stats 257333.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845198 bytes_read=13310704 bytes_retransmit=9 bytes_invalid=0 send_seq=95820 receive_seq=95820 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004300 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.09 cputime=10459.789 memavail=3557964 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=157.7 pwm=1.000
Stats 257334.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845204 bytes_read=13310941 bytes_retransmit=9 bytes_invalid=0 send_seq=95821 receive_seq=95821 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004326 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.09 cputime=10459.829 memavail=3557904 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=161.2 pwm=1.000
Stats 257335.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845210 bytes_read=13311163 bytes_retransmit=9 bytes_invalid=0 send_seq=95822 receive_seq=95822 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004238 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.09 cputime=10459.853 memavail=3558028 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=166.1 pwm=1.000
Stats 257336.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845232 bytes_read=13311352 bytes_retransmit=9 bytes_invalid=0 send_seq=95824 receive_seq=95824 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004248 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.09 cputime=10459.888 memavail=3557932 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=169.1 pwm=1.000
Stats 257337.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845238 bytes_read=13311562 bytes_retransmit=9 bytes_invalid=0 send_seq=95825 receive_seq=95825 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004227 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.09 cputime=10459.929 memavail=3557772 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=172.6 pwm=1.000
Stats 257338.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845244 bytes_read=13311784 bytes_retransmit=9 bytes_invalid=0 send_seq=95826 receive_seq=95826 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004207 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.17 cputime=10459.953 memavail=3557804 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=177.0 pwm=1.000
Stats 257339.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845298 bytes_read=13312006 bytes_retransmit=9 bytes_invalid=0 send_seq=95830 receive_seq=95830 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004257 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.17 cputime=10459.991 memavail=3558028 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=180.2 pwm=0.703
Stats 257340.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845347 bytes_read=13312239 bytes_retransmit=9 bytes_invalid=0 send_seq=95833 receive_seq=95833 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004279 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.17 cputime=10460.033 memavail=3557996 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=183.3 pwm=0.488
Stats 257341.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845385 bytes_read=13312471 bytes_retransmit=9 bytes_invalid=0 send_seq=95836 receive_seq=95836 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004358 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.17 cputime=10460.058 memavail=3557932 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=187.7 pwm=0.349
Stats 257342.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845407 bytes_read=13312669 bytes_retransmit=9 bytes_invalid=0 send_seq=95838 receive_seq=95838 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004376 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.17 cputime=10460.092 memavail=3557996 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=190.6 pwm=0.258
Stats 257343.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845429 bytes_read=13312897 bytes_retransmit=9 bytes_invalid=0 send_seq=95840 receive_seq=95840 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004307 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.15 cputime=10460.132 memavail=3557932 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=193.3 pwm=0.208
Stats 257344.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845446 bytes_read=13313133 bytes_retransmit=9 bytes_invalid=0 send_seq=95841 receive_seq=95841 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004331 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.8 pwm=0.000 sysload=1.15 cputime=10460.156 memavail=3557996 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=196.3 pwm=0.155
Stats 257345.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845452 bytes_read=13313326 bytes_retransmit=9 bytes_invalid=0 send_seq=95842 receive_seq=95842 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004376 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.15 cputime=10460.184 memavail=3557684 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=198.4 pwm=0.155
Stats 257346.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845474 bytes_read=13313569 bytes_retransmit=9 bytes_invalid=0 send_seq=95844 receive_seq=95844 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004436 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.15 cputime=10460.209 memavail=3557652 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=200.0 pwm=0.208
Stats 257347.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845480 bytes_read=13313776 bytes_retransmit=9 bytes_invalid=0 send_seq=95845 receive_seq=95845 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004520 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.8 pwm=0.000 sysload=1.15 cputime=10460.240 memavail=3557716 print_time=59184.413 buffer_time=0.000 print_stall=0 extruder: target=220 temp=201.8 pwm=0.208
Heater extruder within range of 220.000
Transition to shutdown state: Unable to write tmc spi 'extruder' register GLOBALSCALER
Dumping gcode input 0 blocks
Dumping 20 requests for client 548336828720
Received 198120.832953: b'{"id": 548248557584, "method": "objects/query", "params": {"objects": {"configfile": null}}}'
Received 198121.083539: b'{"id": 548248557584, "method": "register_remote_method", "params": {"response_template": {"method": "shutdown_machine"}, "remote_method": "shutdown_machine"}}'
Received 198121.086310: b'{"id": 548237516160, "method": "register_remote_method", "params": {"response_template": {"method": "reboot_machine"}, "remote_method": "reboot_machine"}}'
Received 198121.088396: b'{"id": 548248564688, "method": "register_remote_method", "params": {"response_template": {"method": "pause_job_queue"}, "remote_method": "pause_job_queue"}}'
Received 198121.090409: b'{"id": 548237514096, "method": "register_remote_method", "params": {"response_template": {"method": "start_job_queue"}, "remote_method": "start_job_queue"}}'
Received 198121.099638: b'{"id": 548237814576, "method": "objects/query", "params": {"objects": {"heaters": null}}}'
Received 198121.101059: b'{"id": 548237815968, "method": "objects/query", "params": {"objects": {"heaters": null}}}'
Received 198121.119988: b'{"id": 548237815680, "method": "info", "params": {}}'
Received 198121.122105: b'{"id": 548237815152, "method": "objects/list", "params": {}}'
Received 198121.150246: b'{"id": 548248564688, "method": "objects/subscribe", "params": {"objects": {"gcode": null, "webhooks": null, "configfile": null, "mcu": null, "gcode_macro CHOPPER_TUNE": null, "gcode_macro _detect_driver": null, "gcode_macro _chop_apply_regs": null, "gcode_macro _chop_workflow": null, "gcode_move": null, "print_stats": null, "virtual_sdcard": null, "pause_resume": null, "display_status": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro SET_PAUSE_NEXT_LAYER": null, "gcode_macro SET_PAUSE_AT_LAYER": null, "gcode_macro SET_PRINT_STATS_INFO": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "gcode_macro _CLIENT_EXTRUDE": null, "gcode_macro _CLIENT_RETRACT": null, "gcode_macro BED_MESH_CALIBRATE": null, "gcode_macro LINE_PURGE": null, "gcode_macro SMART_PARK": null, "gcode_macro _KAMP_Settings": null, "gcode_macro _TAP_VARIABLES": null, "gcode_macro _PRE_PROBE_CHECK": null, "gcode_macro _PROBE_TEMP_CHECK": null, "gcode_macro _POST_PROBING": null, "gcode_macro _POST_PROBE": null, "gcode_macro SET_PROBE_TEMP": null, "gcode_macro Z_TILT_ADJUST": null, "gcode_macro _TAP_SETTINGS": null, "heaters": null, "stepper_enable": null, "tmc5160 stepper_y": null, "tmc5160 stepper_x": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 stepper_z2": null, "tmc5160 extruder": null, "heater_bed": null, "probe": null, "heater_fan hotend_fan": null, "fan_generic fan0": null, "idle_timeout": null, "bed_mesh": null, "z_tilt": null, "gcode_macro G32": null, "save_variables": null, "gcode_macro _PREHEAT": null, "gcode_macro _COOLOFF": null, "gcode_macro PRINT_START": null, "gcode_macro PRINT_END": null, "exclude_object": null, "filaments": null, "z_thermal_adjust": null, "led led_strip": null, "heater_generic chamber_heater": null, "heater_fan chamber_heater_fan": null, "fan_generic fan2": null, "gcode_macro M106": null, "gcode_macro _ENABLE_FAN": null, "motion_report": null, "query_endstops": null, "system_stats": null, "manual_probe": null, "toolhead": null, "extruder": null, "fan": ["speed"], "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "screws_tilt_adjust": ["results", "error"]}, "response_template": {"method": "process_status_update"}}}'
Received 198121.377504: b'{"id": 548237518992, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "z_thermal_adjust": null, "heater_generic chamber_heater": null, "extruder": null, "bed_mesh": null, "configfile": null, "display_status": null, "fan": ["speed"], "gcode_move": null, "idle_timeout": null, "pause_resume": null, "toolhead": null, "virtual_sdcard": null, "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "motion_report": null, "exclude_object": null, "manual_probe": null, "screws_tilt_adjust": ["results", "error"], "fan_generic fan0": null, "fan_generic fan2": null, "heater_fan hotend_fan": null, "heater_fan chamber_heater_fan": null, "led led_strip": null, "gcode": null, "mcu": null, "gcode_macro CHOPPER_TUNE": null, "gcode_macro _detect_driver": null, "gcode_macro _chop_apply_regs": null, "gcode_macro _chop_workflow": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro SET_PAUSE_NEXT_LAYER": null, "gcode_macro SET_PAUSE_AT_LAYER": null, "gcode_macro SET_PRINT_STATS_INFO": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "gcode_macro _CLIENT_EXTRUDE": null, "gcode_macro _CLIENT_RETRACT": null, "gcode_macro BED_MESH_CALIBRATE": null, "gcode_macro LINE_PURGE": null, "gcode_macro SMART_PARK": null, "gcode_macro _KAMP_Settings": null, "gcode_macro _TAP_VARIABLES": null, "gcode_macro _PRE_PROBE_CHECK": null, "gcode_macro _PROBE_TEMP_CHECK": null, "gcode_macro _POST_PROBING": null, "gcode_macro _POST_PROBE": null, "gcode_macro SET_PROBE_TEMP": null, "gcode_macro Z_TILT_ADJUST": null, "gcode_macro _TAP_SETTINGS": null, "heaters": null, "stepper_enable": null, "tmc5160 stepper_y": null, "tmc5160 stepper_x": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 stepper_z2": null, "tmc5160 extruder": null, "probe": null, "z_tilt": null, "gcode_macro G32": null, "save_variables": null, "gcode_macro _PREHEAT": null, "gcode_macro _COOLOFF": null, "gcode_macro PRINT_START": null, "gcode_macro PRINT_END": null, "filaments": null, "gcode_macro M106": null, "gcode_macro _ENABLE_FAN": null, "query_endstops": null, "system_stats": null}, "response_template": {"method": "process_status_update"}}}'
Received 198121.595531: b'{"id": 548237514192, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "z_thermal_adjust": null, "heater_generic chamber_heater": null, "extruder": null, "bed_mesh": null, "configfile": null, "display_status": null, "fan": ["speed"], "gcode_move": null, "idle_timeout": null, "pause_resume": null, "toolhead": null, "virtual_sdcard": null, "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "motion_report": null, "exclude_object": null, "manual_probe": null, "screws_tilt_adjust": ["results", "error"], "fan_generic fan0": null, "fan_generic fan2": null, "heater_fan hotend_fan": null, "heater_fan chamber_heater_fan": null, "led led_strip": null, "gcode": null, "mcu": null, "gcode_macro CHOPPER_TUNE": null, "gcode_macro _detect_driver": null, "gcode_macro _chop_apply_regs": null, "gcode_macro _chop_workflow": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro SET_PAUSE_NEXT_LAYER": null, "gcode_macro SET_PAUSE_AT_LAYER": null, "gcode_macro SET_PRINT_STATS_INFO": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "gcode_macro _CLIENT_EXTRUDE": null, "gcode_macro _CLIENT_RETRACT": null, "gcode_macro BED_MESH_CALIBRATE": null, "gcode_macro LINE_PURGE": null, "gcode_macro SMART_PARK": null, "gcode_macro _KAMP_Settings": null, "gcode_macro _TAP_VARIABLES": null, "gcode_macro _PRE_PROBE_CHECK": null, "gcode_macro _PROBE_TEMP_CHECK": null, "gcode_macro _POST_PROBING": null, "gcode_macro _POST_PROBE": null, "gcode_macro SET_PROBE_TEMP": null, "gcode_macro Z_TILT_ADJUST": null, "gcode_macro _TAP_SETTINGS": null, "heaters": null, "stepper_enable": null, "tmc5160 stepper_y": null, "tmc5160 stepper_x": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 stepper_z2": null, "tmc5160 extruder": null, "probe": null, "z_tilt": null, "gcode_macro G32": null, "save_variables": null, "gcode_macro _PREHEAT": null, "gcode_macro _COOLOFF": null, "gcode_macro PRINT_START": null, "gcode_macro PRINT_END": null, "filaments": null, "gcode_macro M106": null, "gcode_macro _ENABLE_FAN": null, "query_endstops": null, "system_stats": null}, "response_template": {"method": "process_status_update"}}}'
Received 198121.845047: b'{"id": 548237512704, "method": "objects/subscribe", "params": {"objects": {"print_stats": null, "webhooks": null, "virtual_sdcard": null, "history": null, "bed_mesh": null, "configfile": null, "display_status": null, "fan": ["speed"], "gcode_move": null, "idle_timeout": null, "pause_resume": null, "toolhead": null, "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "motion_report": null, "exclude_object": null, "manual_probe": null, "screws_tilt_adjust": ["results", "error"], "extruder": null, "heater_bed": null, "heater_generic chamber_heater": null, "fan_generic fan0": null, "fan_generic fan2": null, "heater_fan hotend_fan": null, "heater_fan chamber_heater_fan": null, "led led_strip": null, "z_thermal_adjust": null, "gcode": null, "mcu": null, "gcode_macro CHOPPER_TUNE": null, "gcode_macro _detect_driver": null, "gcode_macro _chop_apply_regs": null, "gcode_macro _chop_workflow": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro SET_PAUSE_NEXT_LAYER": null, "gcode_macro SET_PAUSE_AT_LAYER": null, "gcode_macro SET_PRINT_STATS_INFO": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "gcode_macro _CLIENT_EXTRUDE": null, "gcode_macro _CLIENT_RETRACT": null, "gcode_macro BED_MESH_CALIBRATE": null, "gcode_macro LINE_PURGE": null, "gcode_macro SMART_PARK": null, "gcode_macro _KAMP_Settings": null, "gcode_macro _TAP_VARIABLES": null, "gcode_macro _PRE_PROBE_CHECK": null, "gcode_macro _PROBE_TEMP_CHECK": null, "gcode_macro _POST_PROBING": null, "gcode_macro _POST_PROBE": null, "gcode_macro SET_PROBE_TEMP": null, "gcode_macro Z_TILT_ADJUST": null, "gcode_macro _TAP_SETTINGS": null, "heaters": null, "stepper_enable": null, "tmc5160 stepper_y": null, "tmc5160 stepper_x": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 stepper_z2": null, "tmc5160 extruder": null, "probe": null, "z_tilt": null, "gcode_macro G32": null, "save_variables": null, "gcode_macro _PREHEAT": null, "gcode_macro _COOLOFF": null, "gcode_macro PRINT_START": null, "gcode_macro PRINT_END": null, "filaments": null, "gcode_macro M106": null, "gcode_macro _ENABLE_FAN": null, "query_endstops": null, "system_stats": null}, "response_template": {"method": "process_status_update"}}}'
Received 198121.924617: b'{"id": 548237515056, "method": "objects/query", "params": {"objects": {"extruder": ["can_extrude"]}}}'
Received 198122.102314: b'{"id": 548237514096, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 198124.621426: b'{"id": 548237515056, "method": "gcode/script", "params": {"script": "G28 X"}}'
Received 198129.857575: b'{"id": 548237509728, "method": "gcode/script", "params": {"script": "DUMP_TMC stepper=extruder"}}'
Received 200658.799620: b'{"id": 548237509680, "method": "gcode/script", "params": {"script": "M84"}}'
Received 257298.218143: b'{"id": 548237523072, "method": "gcode/script", "params": {"script": "SET_HEATER_TEMPERATURE HEATER=extruder TARGET=220"}}'
Received 257348.432939: b'{"id": 548237518800, "method": "gcode/script", "params": {"script": "SAVE_GCODE_STATE NAME=_ui_extrude\\nM83\\nG1 E25 F300\\nRESTORE_GCODE_STATE NAME=_ui_extrude"}}'
gcode state: absolute_coord=True absolute_extrude=True base_position=[0.0, 0.0, 0.0, 25.0] last_position=[350.0, 0.0, 5.1757227712850655, 25.0] homing_position=[0.0, 0.0, 0.0, 0.0] speed_factor=0.016666666666666666 extrude_factor=1.0 speed=25.0
Reactor garbage collection: (198124.844309315, 0.0, 0.0)
MCU 'mcu' shutdown: Command request
clocksync state: mcu_freq=180000000 last_clock=10662200225579 clock_est=(257319.939 10657059161402 180004498.580) min_half_rtt=0.000103 min_rtt_time=255320.896 time_avg=257319.939(843.800) clock_avg=10657059161402.850(151887869709.643) pred_variance=2321303884.705
Dumping serial stats: bytes_write=845728 bytes_read=13314047 bytes_retransmit=9 bytes_invalid=0 send_seq=95856 receive_seq=95856 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0
Dumping send queue 100 messages
Sent 0 257281.528684 257281.528684 6: seq: 1c, get_clock
Sent 1 257282.513129 257282.513129 6: seq: 1d, get_clock
Sent 2 257283.497878 257283.497878 6: seq: 1e, get_clock
Sent 3 257284.482332 257284.482332 6: seq: 1f, get_clock
Sent 4 257285.467243 257285.467243 6: seq: 10, get_clock
Sent 5 257286.451626 257286.451626 6: seq: 11, get_clock
Sent 6 257287.435844 257287.435844 6: seq: 12, get_clock
Sent 7 257288.420622 257288.420622 6: seq: 13, get_clock
Sent 8 257289.405216 257289.405216 6: seq: 14, get_clock
Sent 9 257290.390254 257290.390254 6: seq: 15, get_clock
Sent 10 257291.374823 257291.374823 6: seq: 16, get_clock
Sent 11 257292.359207 257292.359207 6: seq: 17, get_clock
Sent 12 257293.343916 257293.343916 6: seq: 18, get_clock
Sent 13 257294.328336 257294.328336 6: seq: 19, get_clock
Sent 14 257295.313222 257295.313222 6: seq: 1a, get_clock
Sent 15 257296.297584 257296.297584 6: seq: 1b, get_clock
Sent 16 257297.281934 257297.281934 6: seq: 1c, get_clock
Sent 17 257298.266848 257298.266848 6: seq: 1d, get_clock
Sent 18 257298.365804 257298.365804 16: seq: 1e, queue_digital_out oid=36 clock=1701545920 on_ticks=18000000
Sent 19 257298.780610 257298.780610 16: seq: 1f, queue_digital_out oid=20 clock=1749507626 on_ticks=1800000
Sent 20 257299.251462 257299.251462 6: seq: 10, get_clock
Sent 21 257300.236057 257300.236057 6: seq: 11, get_clock
Sent 22 257301.227282 257301.227282 6: seq: 12, get_clock
Sent 23 257302.211679 257302.211679 6: seq: 13, get_clock
Sent 24 257302.565595 257302.565595 16: seq: 14, queue_digital_out oid=36 clock=2457545920 on_ticks=18000000
Sent 25 257303.196277 257303.196277 6: seq: 15, get_clock
Sent 26 257304.181568 257304.181568 6: seq: 16, get_clock
Sent 27 257305.166863 257305.166863 6: seq: 17, get_clock
Sent 28 257306.151356 257306.151356 6: seq: 18, get_clock
Sent 29 257306.765947 257306.765947 16: seq: 19, queue_digital_out oid=36 clock=3213545920 on_ticks=18000000
Sent 30 257307.136055 257307.136055 6: seq: 1a, get_clock
Sent 31 257308.120493 257308.120493 6: seq: 1b, get_clock
Sent 32 257309.104978 257309.104978 6: seq: 1c, get_clock
Sent 33 257310.089641 257310.089641 6: seq: 1d, get_clock
Sent 34 257310.965724 257310.965724 16: seq: 1e, queue_digital_out oid=36 clock=3969545920 on_ticks=18000000
Sent 35 257311.074309 257311.074309 6: seq: 1f, get_clock
Sent 36 257312.059182 257312.059182 6: seq: 10, get_clock
Sent 37 257313.044200 257313.044200 6: seq: 11, get_clock
Sent 38 257314.028747 257314.028747 6: seq: 12, get_clock
Sent 39 257315.013916 257315.013916 6: seq: 13, get_clock
Sent 40 257315.165544 257315.165544 16: seq: 14, queue_digital_out oid=36 clock=430578624 on_ticks=18000000
Sent 41 257315.998360 257315.998360 6: seq: 15, get_clock
Sent 42 257316.982593 257316.982593 6: seq: 16, get_clock
Sent 43 257317.967506 257317.967506 6: seq: 17, get_clock
Sent 44 257318.953005 257318.953005 6: seq: 18, get_clock
Sent 45 257319.365414 257319.365414 16: seq: 19, queue_digital_out oid=36 clock=1186578624 on_ticks=18000000
Sent 46 257319.937716 257319.937716 6: seq: 1a, get_clock
Sent 47 257320.922948 257320.922948 6: seq: 1b, get_clock
Sent 48 257321.908303 257321.908303 6: seq: 1c, get_clock
Sent 49 257322.893160 257322.893160 6: seq: 1d, get_clock
Sent 50 257323.565489 257323.565489 16: seq: 1e, queue_digital_out oid=36 clock=1942578624 on_ticks=18000000
Sent 51 257323.878122 257323.878122 6: seq: 1f, get_clock
Sent 52 257324.862836 257324.862836 6: seq: 10, get_clock
Sent 53 257325.847085 257325.847085 6: seq: 11, get_clock
Sent 54 257326.831072 257326.831072 6: seq: 12, get_clock
Sent 55 257327.765828 257327.765828 16: seq: 13, queue_digital_out oid=36 clock=2698578624 on_ticks=18000000
Sent 56 257327.819451 257327.819451 6: seq: 14, get_clock
Sent 57 257328.803622 257328.803622 6: seq: 15, get_clock
Sent 58 257329.789022 257329.789022 6: seq: 16, get_clock
Sent 59 257330.774181 257330.774181 6: seq: 17, get_clock
Sent 60 257331.758779 257331.758779 6: seq: 18, get_clock
Sent 61 257331.965538 257331.965538 16: seq: 19, queue_digital_out oid=36 clock=3454578624 on_ticks=18000000
Sent 62 257332.743734 257332.743734 6: seq: 1a, get_clock
Sent 63 257333.728350 257333.728350 6: seq: 1b, get_clock
Sent 64 257334.712812 257334.712812 6: seq: 1c, get_clock
Sent 65 257335.697378 257335.697378 6: seq: 1d, get_clock
Sent 66 257336.165439 257336.165439 16: seq: 1e, queue_digital_out oid=36 clock=4210578624 on_ticks=18000000
Sent 67 257336.681910 257336.681910 6: seq: 1f, get_clock
Sent 68 257337.666057 257337.666057 6: seq: 10, get_clock
Sent 69 257338.651064 257338.651064 6: seq: 11, get_clock
Sent 70 257339.164570 257339.164570 16: seq: 12, queue_digital_out oid=36 clock=455611328 on_ticks=16674783
Sent 71 257339.465213 257339.465213 16: seq: 13, queue_digital_out oid=36 clock=509611328 on_ticks=14399643
Sent 72 257339.635727 257339.635727 6: seq: 14, get_clock
Sent 73 257339.765520 257339.765520 16: seq: 15, queue_digital_out oid=36 clock=563611328 on_ticks=12655759
Sent 74 257340.064599 257340.064599 16: seq: 16, queue_digital_out oid=36 clock=617611328 on_ticks=11005024
Sent 75 257340.365286 257340.365286 16: seq: 17, queue_digital_out oid=36 clock=671611328 on_ticks=9760304
Sent 76 257340.619854 257340.619854 17: seq: 18, get_clock, queue_digital_out oid=36 clock=725611328 on_ticks=8782782
Sent 77 257340.964680 257340.964680 16: seq: 19, queue_digital_out oid=36 clock=779611328 on_ticks=7648286
Sent 78 257341.564441 257341.564441 16: seq: 1a, queue_digital_out oid=36 clock=887611328 on_ticks=6287321
Sent 79 257341.606556 257341.606556 6: seq: 1b, get_clock
Sent 80 257342.164836 257342.164836 16: seq: 1c, queue_digital_out oid=36 clock=995611328 on_ticks=4652709
Sent 81 257342.591836 257342.591836 6: seq: 1d, get_clock
Sent 82 257343.364913 257343.364913 16: seq: 1e, queue_digital_out oid=36 clock=1211611328 on_ticks=3745689
Sent 83 257343.576258 257343.576258 6: seq: 1f, get_clock
Sent 84 257344.560829 257344.560829 17: seq: 10, get_clock, queue_digital_out oid=36 clock=1427611328 on_ticks=2783153
Sent 85 257345.545709 257345.545709 6: seq: 11, get_clock
Sent 86 257346.530624 257346.530624 6: seq: 12, get_clock
Sent 87 257346.664602 257346.664602 16: seq: 13, queue_digital_out oid=36 clock=1805611328 on_ticks=3740255
Sent 88 257347.515484 257347.515484 6: seq: 14, get_clock
Sent 89 257348.464607 257348.464607 16: seq: 15, queue_digital_out oid=36 clock=2129611328 on_ticks=4699783
Sent 90 257348.499976 257348.499976 6: seq: 16, get_clock
Sent 91 257348.536314 257348.536314 33: seq: 17, set_next_step_dir oid=17 dir=0, queue_digital_out oid=37 clock=2142759001 on_ticks=0, queue_step oid=17 interval=2142821620 count=1 add=0, queue_step oid=17 interval=52166 count=1654 add=0
Sent 92 257348.539778 257348.539778 61: seq: 18, queue_step oid=17 interval=52167 count=1725 add=0, queue_step oid=17 interval=52166 count=1726 add=0, queue_step oid=17 interval=52166 count=1725 add=0, queue_step oid=17 interval=52166 count=1725 add=0, queue_step oid=17 interval=52167 count=1725 add=0, queue_step oid=17 interval=52166 count=1726 add=0, queue_step oid=17 interval=52166 count=1725 add=0
Sent 93 257348.540702 257348.540702 37: seq: 19, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00', queue_step oid=17 interval=52166 count=1725 add=0, queue_step oid=17 interval=52167 count=1725 add=0
Sent 94 257348.543705 257348.543705 13: seq: 1a, spi_send oid=5 data=b'\x8b\x00\x00\x00 '
Sent 95 257348.543842 257348.543842 13: seq: 1b, spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 96 257348.545468 257348.545468 21: seq: 1c, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 97 257348.548458 257348.548458 21: seq: 1d, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 98 257348.551573 257348.551573 21: seq: 1e, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 99 257348.556698 257348.556698 6: seq: 1f, emergency_stop
Dumping receive queue 100 messages
Receive: 0 257342.112710 257341.606556 14: seq: 1c, analog_in_state oid=35 next_clock=994171328 value=8767
Receive: 1 257342.242762 257342.164836 15: seq: 1d, analog_in_state oid=18 next_clock=1017571328 value=31462
Receive: 2 257342.282759 257342.164836 15: seq: 1d, analog_in_state oid=22 next_clock=1024771328 value=23248
Receive: 3 257342.322693 257342.164836 15: seq: 1d, analog_in_state oid=26 next_clock=1031971328 value=31464
Receive: 4 257342.412952 257342.164836 14: seq: 1d, analog_in_state oid=35 next_clock=1048171328 value=8776
Receive: 5 257342.542849 257342.164836 15: seq: 1d, analog_in_state oid=18 next_clock=1071571328 value=31457
Receive: 6 257342.582854 257342.164836 15: seq: 1d, analog_in_state oid=22 next_clock=1078771328 value=23249
Receive: 7 257342.592847 257342.591836 11: seq: 1e, clock clock=1027931338
Receive: 8 257342.622897 257342.591836 15: seq: 1e, analog_in_state oid=26 next_clock=1085971328 value=31463
Receive: 9 257342.712793 257342.591836 14: seq: 1e, analog_in_state oid=35 next_clock=1102171328 value=8791
Receive: 10 257342.842888 257342.591836 15: seq: 1e, analog_in_state oid=18 next_clock=1125571328 value=31461
Receive: 11 257342.883099 257342.591836 15: seq: 1e, analog_in_state oid=22 next_clock=1132771328 value=23251
Receive: 12 257342.923048 257342.591836 15: seq: 1e, analog_in_state oid=26 next_clock=1139971328 value=31466
Receive: 13 257343.012804 257342.591836 14: seq: 1e, analog_in_state oid=35 next_clock=1156171328 value=8793
Receive: 14 257343.143119 257342.591836 15: seq: 1e, analog_in_state oid=18 next_clock=1179571328 value=31460
Receive: 15 257343.182871 257342.591836 15: seq: 1e, analog_in_state oid=22 next_clock=1186771328 value=23250
Receive: 16 257343.222849 257342.591836 15: seq: 1e, analog_in_state oid=26 next_clock=1193971328 value=31466
Receive: 17 257343.312963 257342.591836 14: seq: 1e, analog_in_state oid=35 next_clock=1210171328 value=8816
Receive: 18 257343.442738 257343.364913 15: seq: 1f, analog_in_state oid=18 next_clock=1233571328 value=31460
Receive: 19 257343.482783 257343.364913 15: seq: 1f, analog_in_state oid=22 next_clock=1240771328 value=23248
Receive: 20 257343.522756 257343.364913 15: seq: 1f, analog_in_state oid=26 next_clock=1247971328 value=31463
Receive: 21 257343.576574 257343.576258 11: seq: 10, clock clock=1205055564
Receive: 22 257343.612764 257343.576258 14: seq: 10, analog_in_state oid=35 next_clock=1264171328 value=8829
Receive: 23 257343.742659 257343.576258 15: seq: 10, analog_in_state oid=18 next_clock=1287571328 value=31457
Receive: 24 257343.782649 257343.576258 15: seq: 10, analog_in_state oid=22 next_clock=1294771328 value=23250
Receive: 25 257343.822900 257343.576258 15: seq: 10, analog_in_state oid=26 next_clock=1301971328 value=31466
Receive: 26 257343.912648 257343.576258 14: seq: 10, analog_in_state oid=35 next_clock=1318171328 value=8840
Receive: 27 257344.042652 257343.576258 15: seq: 10, analog_in_state oid=18 next_clock=1341571328 value=31459
Receive: 28 257344.082655 257343.576258 15: seq: 10, analog_in_state oid=22 next_clock=1348771328 value=23249
Receive: 29 257344.122668 257343.576258 15: seq: 10, analog_in_state oid=26 next_clock=1355971328 value=31465
Receive: 30 257344.212600 257343.576258 14: seq: 10, analog_in_state oid=35 next_clock=1372171328 value=8849
Receive: 31 257344.342647 257343.576258 15: seq: 10, analog_in_state oid=18 next_clock=1395571328 value=31457
Receive: 32 257344.382673 257343.576258 15: seq: 10, analog_in_state oid=22 next_clock=1402771328 value=23249
Receive: 33 257344.422784 257343.576258 15: seq: 10, analog_in_state oid=26 next_clock=1409971328 value=31465
Receive: 34 257344.512649 257343.576258 14: seq: 10, analog_in_state oid=35 next_clock=1426171328 value=8863
Receive: 35 257344.512668 257343.576258 14: seq: 10, stats count=212 sum=187508 sumsq=1101284
Receive: 36 257344.561660 257344.560829 11: seq: 11, clock clock=1382361246
Receive: 37 257344.642763 257344.560829 15: seq: 11, analog_in_state oid=18 next_clock=1449571328 value=31458
Receive: 38 257344.682760 257344.560829 15: seq: 11, analog_in_state oid=22 next_clock=1456771328 value=23250
Receive: 39 257344.722761 257344.560829 15: seq: 11, analog_in_state oid=26 next_clock=1463971328 value=31468
Receive: 40 257344.812605 257344.560829 14: seq: 11, analog_in_state oid=35 next_clock=1480171328 value=8870
Receive: 41 257344.942756 257344.560829 15: seq: 11, analog_in_state oid=18 next_clock=1503571328 value=31460
Receive: 42 257344.982757 257344.560829 15: seq: 11, analog_in_state oid=22 next_clock=1510771328 value=23250
Receive: 43 257345.022762 257344.560829 15: seq: 11, analog_in_state oid=26 next_clock=1517971328 value=31468
Receive: 44 257345.112644 257344.560829 14: seq: 11, analog_in_state oid=35 next_clock=1534171328 value=8883
Receive: 45 257345.242755 257344.560829 15: seq: 11, analog_in_state oid=18 next_clock=1557571328 value=31460
Receive: 46 257345.282743 257344.560829 15: seq: 11, analog_in_state oid=22 next_clock=1564771328 value=23248
Receive: 47 257345.322924 257344.560829 15: seq: 11, analog_in_state oid=26 next_clock=1571971328 value=31468
Receive: 48 257345.412928 257344.560829 14: seq: 11, analog_in_state oid=35 next_clock=1588171328 value=8890
Receive: 49 257345.542626 257344.560829 15: seq: 11, analog_in_state oid=18 next_clock=1611571328 value=31459
Receive: 50 257345.546609 257345.545709 11: seq: 12, clock clock=1559664119
Receive: 51 257345.582655 257345.545709 15: seq: 12, analog_in_state oid=22 next_clock=1618771328 value=23249
Receive: 52 257345.622688 257345.545709 15: seq: 12, analog_in_state oid=26 next_clock=1625971328 value=31467
Receive: 53 257345.712678 257345.545709 14: seq: 12, analog_in_state oid=35 next_clock=1642171328 value=8898
Receive: 54 257345.842675 257345.545709 15: seq: 12, analog_in_state oid=18 next_clock=1665571328 value=31459
Receive: 55 257345.882678 257345.545709 15: seq: 12, analog_in_state oid=22 next_clock=1672771328 value=23249
Receive: 56 257345.922673 257345.545709 15: seq: 12, analog_in_state oid=26 next_clock=1679971328 value=31467
Receive: 57 257346.012672 257345.545709 14: seq: 12, analog_in_state oid=35 next_clock=1696171328 value=8905
Receive: 58 257346.142788 257345.545709 15: seq: 12, analog_in_state oid=18 next_clock=1719571328 value=31458
Receive: 59 257346.182677 257345.545709 15: seq: 12, analog_in_state oid=22 next_clock=1726771328 value=23251
Receive: 60 257346.222675 257345.545709 15: seq: 12, analog_in_state oid=26 next_clock=1733971328 value=31464
Receive: 61 257346.312676 257345.545709 14: seq: 12, analog_in_state oid=35 next_clock=1750171328 value=8913
Receive: 62 257346.442677 257345.545709 15: seq: 12, analog_in_state oid=18 next_clock=1773571328 value=31459
Receive: 63 257346.482647 257345.545709 15: seq: 12, analog_in_state oid=22 next_clock=1780771328 value=23248
Receive: 64 257346.522671 257345.545709 15: seq: 12, analog_in_state oid=26 next_clock=1787971328 value=31467
Receive: 65 257346.531673 257346.530624 11: seq: 13, clock clock=1736968335
Receive: 66 257346.612671 257346.530624 14: seq: 13, analog_in_state oid=35 next_clock=1804171328 value=8920
Receive: 67 257346.742698 257346.664602 15: seq: 14, analog_in_state oid=18 next_clock=1827571328 value=31457
Receive: 68 257346.782681 257346.664602 15: seq: 14, analog_in_state oid=22 next_clock=1834771328 value=23248
Receive: 69 257346.822666 257346.664602 15: seq: 14, analog_in_state oid=26 next_clock=1841971328 value=31466
Receive: 70 257346.912677 257346.664602 14: seq: 14, analog_in_state oid=35 next_clock=1858171328 value=8928
Receive: 71 257347.042673 257346.664602 15: seq: 14, analog_in_state oid=18 next_clock=1881571328 value=31458
Receive: 72 257347.082671 257346.664602 15: seq: 14, analog_in_state oid=22 next_clock=1888771328 value=23247
Receive: 73 257347.122780 257346.664602 15: seq: 14, analog_in_state oid=26 next_clock=1895971328 value=31467
Receive: 74 257347.212685 257346.664602 14: seq: 14, analog_in_state oid=35 next_clock=1912171328 value=8935
Receive: 75 257347.342712 257346.664602 15: seq: 14, analog_in_state oid=18 next_clock=1935571328 value=31455
Receive: 76 257347.382745 257346.664602 15: seq: 14, analog_in_state oid=22 next_clock=1942771328 value=23249
Receive: 77 257347.422765 257346.664602 15: seq: 14, analog_in_state oid=26 next_clock=1949971328 value=31467
Receive: 78 257347.512627 257346.664602 14: seq: 14, analog_in_state oid=35 next_clock=1966171328 value=8943
Receive: 79 257347.516614 257347.515484 11: seq: 15, clock clock=1914272879
Receive: 80 257347.642965 257347.515484 15: seq: 15, analog_in_state oid=18 next_clock=1989571328 value=31457
Receive: 81 257347.682942 257347.515484 15: seq: 15, analog_in_state oid=22 next_clock=1996771328 value=23249
Receive: 82 257347.723047 257347.515484 15: seq: 15, analog_in_state oid=26 next_clock=2003971328 value=31468
Receive: 83 257347.812852 257347.515484 14: seq: 15, analog_in_state oid=35 next_clock=2020171328 value=8944
Receive: 84 257347.942959 257347.515484 15: seq: 15, analog_in_state oid=18 next_clock=2043571328 value=31456
Receive: 85 257347.983051 257347.515484 15: seq: 15, analog_in_state oid=22 next_clock=2050771328 value=23249
Receive: 86 257348.023063 257347.515484 15: seq: 15, analog_in_state oid=26 next_clock=2057971328 value=31464
Receive: 87 257348.112918 257347.515484 14: seq: 15, analog_in_state oid=35 next_clock=2074171328 value=8951
Receive: 88 257348.242915 257347.515484 15: seq: 15, analog_in_state oid=18 next_clock=2097571328 value=31457
Receive: 89 257348.283109 257347.515484 15: seq: 15, analog_in_state oid=22 next_clock=2104771328 value=23249
Receive: 90 257348.322739 257347.515484 15: seq: 15, analog_in_state oid=26 next_clock=2111971328 value=31465
Receive: 91 257348.412649 257347.515484 14: seq: 15, analog_in_state oid=35 next_clock=2128171328 value=8958
Receive: 92 257348.500662 257348.499976 11: seq: 17, clock clock=2091396907
Receive: 93 257348.542596 257348.540702 13: seq: 1a, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 94 257348.542621 257348.540702 15: seq: 1a, analog_in_state oid=18 next_clock=2151571328 value=31457
Receive: 95 257348.544629 257348.543842 13: seq: 1c, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 96 257348.547613 257348.545468 13: seq: 1d, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 97 257348.550646 257348.548458 13: seq: 1e, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 98 257348.553642 257348.551573 13: seq: 1f, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 99 257348.558620 257348.556698 12: seq: 10, shutdown clock=2101657186 static_string_id=Command request
Stats 257348.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845728 bytes_read=13314047 bytes_retransmit=9 bytes_invalid=0 send_seq=95856 receive_seq=95856 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004498 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.22 cputime=10460.308 memavail=3557684 print_time=59239.731 buffer_time=4.961 print_stall=0 extruder: target=220 temp=202.8 pwm=0.261
Stats 257349.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=845747 bytes_read=13314297 bytes_retransmit=9 bytes_invalid=0 send_seq=95858 receive_seq=95858 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004460 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.22 cputime=10460.334 memavail=3557908 print_time=59239.731 buffer_time=3.960 print_stall=0 extruder: target=220 temp=203.7 pwm=0.000
Stats 257350.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=845753 bytes_read=13314504 bytes_retransmit=9 bytes_invalid=0 send_seq=95859 receive_seq=95859 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004509 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.22 cputime=10460.370 memavail=3557876 print_time=59239.731 buffer_time=2.959 print_stall=0 extruder: target=220 temp=204.4 pwm=0.000
Stats 257351.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=845759 bytes_read=13314697 bytes_retransmit=9 bytes_invalid=0 send_seq=95860 receive_seq=95860 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004471 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.22 cputime=10460.394 memavail=3558004 print_time=59239.731 buffer_time=1.958 print_stall=0 extruder: target=220 temp=204.8 pwm=0.000
Stats 257352.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=845765 bytes_read=13314935 bytes_retransmit=9 bytes_invalid=0 send_seq=95861 receive_seq=95861 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004458 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.22 cputime=10460.422 memavail=3558004 print_time=59239.731 buffer_time=0.957 print_stall=0 extruder: target=220 temp=204.9 pwm=0.000
Stats 257353.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=845790 bytes_read=13315161 bytes_retransmit=9 bytes_invalid=0 send_seq=95863 receive_seq=95863 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004466 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.20 cputime=10460.461 memavail=3557940 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=204.4 pwm=0.000
Stats 257354.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845796 bytes_read=13315368 bytes_retransmit=9 bytes_invalid=0 send_seq=95864 receive_seq=95864 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004425 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.20 cputime=10460.487 memavail=3557984 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=204.4 pwm=0.000
Stats 257355.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845802 bytes_read=13315606 bytes_retransmit=9 bytes_invalid=0 send_seq=95865 receive_seq=95865 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004451 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.20 cputime=10460.521 memavail=3557952 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=204.0 pwm=0.000
Stats 257356.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845808 bytes_read=13315813 bytes_retransmit=9 bytes_invalid=0 send_seq=95866 receive_seq=95866 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004403 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.20 cputime=10460.546 memavail=3557984 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=203.1 pwm=0.000
Stats 257357.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845814 bytes_read=13316006 bytes_retransmit=9 bytes_invalid=0 send_seq=95867 receive_seq=95867 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004367 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.20 cputime=10460.577 memavail=3557984 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=202.4 pwm=0.000
Stats 257358.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845820 bytes_read=13316244 bytes_retransmit=9 bytes_invalid=0 send_seq=95868 receive_seq=95868 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004474 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.35 cputime=10460.620 memavail=3557920 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=201.6 pwm=0.000
Stats 257359.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845826 bytes_read=13316465 bytes_retransmit=9 bytes_invalid=0 send_seq=95869 receive_seq=95869 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004378 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.35 cputime=10460.645 memavail=3557984 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=200.6 pwm=0.000
Stats 257360.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845832 bytes_read=13316649 bytes_retransmit=9 bytes_invalid=0 send_seq=95870 receive_seq=95870 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004445 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.35 cputime=10460.675 memavail=3558268 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=199.7 pwm=0.000
Stats 257361.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845838 bytes_read=13316875 bytes_retransmit=9 bytes_invalid=0 send_seq=95871 receive_seq=95871 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004424 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.35 cputime=10460.700 memavail=3558268 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=198.8 pwm=0.000
Stats 257362.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845844 bytes_read=13317082 bytes_retransmit=9 bytes_invalid=0 send_seq=95872 receive_seq=95872 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004498 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.35 cputime=10460.733 memavail=3558268 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=197.4 pwm=0.000
Stats 257363.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845850 bytes_read=13317275 bytes_retransmit=9 bytes_invalid=0 send_seq=95873 receive_seq=95873 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004395 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.32 cputime=10460.764 memavail=3558204 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=196.7 pwm=0.000
Stats 257364.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845856 bytes_read=13317527 bytes_retransmit=9 bytes_invalid=0 send_seq=95874 receive_seq=95874 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004345 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.32 cputime=10460.791 memavail=3558268 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=195.7 pwm=0.000
Stats 257365.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845862 bytes_read=13317734 bytes_retransmit=9 bytes_invalid=0 send_seq=95875 receive_seq=95875 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004449 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.32 cputime=10460.825 memavail=3558280 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=194.4 pwm=0.000
Stats 257366.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845868 bytes_read=13317927 bytes_retransmit=9 bytes_invalid=0 send_seq=95876 receive_seq=95876 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004531 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.32 cputime=10460.852 memavail=3558120 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=193.6 pwm=0.000
Stats 257367.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845874 bytes_read=13318165 bytes_retransmit=9 bytes_invalid=0 send_seq=95877 receive_seq=95877 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004522 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.32 cputime=10460.885 memavail=3556352 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=192.6 pwm=0.000
Stats 257368.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845880 bytes_read=13318372 bytes_retransmit=9 bytes_invalid=0 send_seq=95878 receive_seq=95878 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004434 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.29 cputime=10460.911 memavail=3557256 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=191.3 pwm=0.000
Stats 257369.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845886 bytes_read=13318594 bytes_retransmit=9 bytes_invalid=0 send_seq=95879 receive_seq=95879 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004336 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10460.936 memavail=3557288 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=190.3 pwm=0.000
Stats 257370.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845892 bytes_read=13318817 bytes_retransmit=9 bytes_invalid=0 send_seq=95880 receive_seq=95880 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004386 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10460.962 memavail=3557448 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=189.5 pwm=0.000
Stats 257371.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845898 bytes_read=13319024 bytes_retransmit=9 bytes_invalid=0 send_seq=95881 receive_seq=95881 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004318 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10460.995 memavail=3557352 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=188.2 pwm=0.000
Stats 257372.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845904 bytes_read=13319232 bytes_retransmit=9 bytes_invalid=0 send_seq=95882 receive_seq=95882 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004321 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10461.032 memavail=3557352 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=187.2 pwm=0.000
Stats 257373.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845910 bytes_read=13319455 bytes_retransmit=9 bytes_invalid=0 send_seq=95883 receive_seq=95883 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004368 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10461.059 memavail=3557352 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=186.2 pwm=0.000
Stats 257374.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845916 bytes_read=13319676 bytes_retransmit=9 bytes_invalid=0 send_seq=95884 receive_seq=95884 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004458 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10461.094 memavail=3557480 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=184.8 pwm=0.000
Stats 257375.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845922 bytes_read=13319884 bytes_retransmit=9 bytes_invalid=0 send_seq=95885 receive_seq=95885 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004505 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10461.118 memavail=3557544 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=184.3 pwm=0.000
Stats 257376.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845928 bytes_read=13320107 bytes_retransmit=9 bytes_invalid=0 send_seq=95886 receive_seq=95886 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004587 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10461.149 memavail=3557320 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=183.0 pwm=0.000
Stats 257377.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845934 bytes_read=13320314 bytes_retransmit=9 bytes_invalid=0 send_seq=95887 receive_seq=95887 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004593 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10461.172 memavail=3557384 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=181.8 pwm=0.000
Stats 257378.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845940 bytes_read=13320522 bytes_retransmit=9 bytes_invalid=0 send_seq=95888 receive_seq=95888 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004499 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.41 cputime=10461.210 memavail=3557320 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=180.8 pwm=0.000
Stats 257379.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845946 bytes_read=13320759 bytes_retransmit=9 bytes_invalid=0 send_seq=95889 receive_seq=95889 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004597 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.41 cputime=10461.247 memavail=3557352 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=180.0 pwm=0.000
Stats 257380.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845952 bytes_read=13320966 bytes_retransmit=9 bytes_invalid=0 send_seq=95890 receive_seq=95890 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004547 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.41 cputime=10461.273 memavail=3557352 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=178.6 pwm=0.000
Stats 257381.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845958 bytes_read=13321174 bytes_retransmit=9 bytes_invalid=0 send_seq=95891 receive_seq=95891 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004631 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.41 cputime=10461.307 memavail=3557384 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=178.0 pwm=0.000
Stats 257382.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845964 bytes_read=13321397 bytes_retransmit=9 bytes_invalid=0 send_seq=95892 receive_seq=95892 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004576 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.41 cputime=10461.346 memavail=3557448 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=177.2 pwm=0.000
Stats 257383.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845970 bytes_read=13321604 bytes_retransmit=9 bytes_invalid=0 send_seq=95893 receive_seq=95893 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004481 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.38 cputime=10461.370 memavail=3557384 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=175.7 pwm=0.000
Stats 257384.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845976 bytes_read=13321813 bytes_retransmit=9 bytes_invalid=0 send_seq=95894 receive_seq=95894 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004400 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.38 cputime=10461.402 memavail=3557480 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=175.0 pwm=0.000
Stats 257385.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845982 bytes_read=13322028 bytes_retransmit=9 bytes_invalid=0 send_seq=95895 receive_seq=95895 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004322 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.38 cputime=10461.427 memavail=3557392 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=174.0 pwm=0.000
Stats 257386.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845988 bytes_read=13322235 bytes_retransmit=9 bytes_invalid=0 send_seq=95896 receive_seq=95896 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004298 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.38 cputime=10461.461 memavail=3557328 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=172.8 pwm=0.000
Stats 257387.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=845994 bytes_read=13322443 bytes_retransmit=9 bytes_invalid=0 send_seq=95897 receive_seq=95897 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004303 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.38 cputime=10461.493 memavail=3557520 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=171.8 pwm=0.000
Stats 257388.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846000 bytes_read=13322666 bytes_retransmit=9 bytes_invalid=0 send_seq=95898 receive_seq=95898 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004304 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.34 cputime=10461.518 memavail=3557328 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=171.0 pwm=0.000
Stats 257389.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846012 bytes_read=13322903 bytes_retransmit=9 bytes_invalid=0 send_seq=95900 receive_seq=95900 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004330 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.34 cputime=10461.549 memavail=3557328 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=169.8 pwm=0.000
Stats 257390.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846018 bytes_read=13323111 bytes_retransmit=9 bytes_invalid=0 send_seq=95901 receive_seq=95901 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004321 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.34 cputime=10461.574 memavail=3557552 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=169.0 pwm=0.000
Stats 257391.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846024 bytes_read=13323334 bytes_retransmit=9 bytes_invalid=0 send_seq=95902 receive_seq=95902 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004282 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.34 cputime=10461.605 memavail=3557392 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=168.2 pwm=0.000
Stats 257392.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846030 bytes_read=13323541 bytes_retransmit=9 bytes_invalid=0 send_seq=95903 receive_seq=95903 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004367 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.34 cputime=10461.629 memavail=3557360 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=167.1 pwm=0.000
Stats 257393.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846036 bytes_read=13323749 bytes_retransmit=9 bytes_invalid=0 send_seq=95904 receive_seq=95904 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004417 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.32 cputime=10461.662 memavail=3557644 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=166.2 pwm=0.000
Stats 257394.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846042 bytes_read=13323986 bytes_retransmit=9 bytes_invalid=0 send_seq=95905 receive_seq=95905 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004323 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.32 cputime=10461.697 memavail=3557516 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=165.2 pwm=0.000
Stats 257395.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846048 bytes_read=13324193 bytes_retransmit=9 bytes_invalid=0 send_seq=95906 receive_seq=95906 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004329 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.32 cputime=10461.721 memavail=3557676 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=164.2 pwm=0.000
Stats 257396.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846054 bytes_read=13324401 bytes_retransmit=9 bytes_invalid=0 send_seq=95907 receive_seq=95907 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004296 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.32 cputime=10461.753 memavail=3557592 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=163.2 pwm=0.000
Stats 257397.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846060 bytes_read=13324624 bytes_retransmit=9 bytes_invalid=0 send_seq=95908 receive_seq=95908 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004335 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.32 cputime=10461.777 memavail=3557600 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=162.4 pwm=0.000
Stats 257398.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846066 bytes_read=13324831 bytes_retransmit=9 bytes_invalid=0 send_seq=95909 receive_seq=95909 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004392 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.29 cputime=10461.819 memavail=3557504 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=161.3 pwm=0.000
Stats 257399.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846072 bytes_read=13325053 bytes_retransmit=9 bytes_invalid=0 send_seq=95910 receive_seq=95910 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004453 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10461.856 memavail=3557664 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=160.6 pwm=0.000
Stats 257400.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846078 bytes_read=13325276 bytes_retransmit=9 bytes_invalid=0 send_seq=95911 receive_seq=95911 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004477 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10461.881 memavail=3557664 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=159.7 pwm=0.000
Stats 257401.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846084 bytes_read=13325483 bytes_retransmit=9 bytes_invalid=0 send_seq=95912 receive_seq=95912 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004383 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.29 cputime=10461.918 memavail=3557664 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=158.6 pwm=0.000
Stats 257402.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846090 bytes_read=13325691 bytes_retransmit=9 bytes_invalid=0 send_seq=95913 receive_seq=95913 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004354 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.29 cputime=10461.952 memavail=3557664 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=157.9 pwm=0.000
Stats 257403.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846096 bytes_read=13325914 bytes_retransmit=9 bytes_invalid=0 send_seq=95914 receive_seq=95914 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004320 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10461.977 memavail=3557696 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=157.2 pwm=0.000
Stats 257404.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846102 bytes_read=13326135 bytes_retransmit=9 bytes_invalid=0 send_seq=95915 receive_seq=95915 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004284 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.27 cputime=10462.008 memavail=3557568 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=156.1 pwm=0.000
Stats 257405.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846108 bytes_read=13326343 bytes_retransmit=9 bytes_invalid=0 send_seq=95916 receive_seq=95916 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004321 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.27 cputime=10462.032 memavail=3557732 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=155.2 pwm=0.000
Stats 257406.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846114 bytes_read=13326566 bytes_retransmit=9 bytes_invalid=0 send_seq=95917 receive_seq=95917 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004414 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10462.063 memavail=3557700 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=154.3 pwm=0.000
Stats 257407.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846120 bytes_read=13326772 bytes_retransmit=9 bytes_invalid=0 send_seq=95918 receive_seq=95918 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004488 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.27 cputime=10462.087 memavail=3557636 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=153.4 pwm=0.000
Stats 257408.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846126 bytes_read=13326966 bytes_retransmit=9 bytes_invalid=0 send_seq=95919 receive_seq=95919 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004452 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.25 cputime=10462.119 memavail=3557636 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=152.7 pwm=0.000
Stats 257409.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846132 bytes_read=13327196 bytes_retransmit=9 bytes_invalid=0 send_seq=95920 receive_seq=95920 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004470 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.25 cputime=10462.151 memavail=3557668 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=151.7 pwm=0.000
Stats 257410.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846138 bytes_read=13327403 bytes_retransmit=9 bytes_invalid=0 send_seq=95921 receive_seq=95921 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004537 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.25 cputime=10462.178 memavail=3557572 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=150.9 pwm=0.000
Stats 257411.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846144 bytes_read=13327611 bytes_retransmit=9 bytes_invalid=0 send_seq=95922 receive_seq=95922 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004430 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.25 cputime=10462.210 memavail=3557668 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=150.0 pwm=0.000
Stats 257412.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846150 bytes_read=13327834 bytes_retransmit=9 bytes_invalid=0 send_seq=95923 receive_seq=95923 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004434 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.25 cputime=10462.235 memavail=3557668 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=149.2 pwm=0.000
Stats 257413.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846156 bytes_read=13328041 bytes_retransmit=9 bytes_invalid=0 send_seq=95924 receive_seq=95924 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004365 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.23 cputime=10462.266 memavail=3557700 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=148.4 pwm=0.000
Stats 257414.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846162 bytes_read=13328263 bytes_retransmit=9 bytes_invalid=0 send_seq=95925 receive_seq=95925 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004420 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.23 cputime=10462.290 memavail=3557636 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=147.8 pwm=0.000
Stats 257415.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846168 bytes_read=13328486 bytes_retransmit=9 bytes_invalid=0 send_seq=95926 receive_seq=95926 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004349 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.23 cputime=10462.319 memavail=3557700 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=146.6 pwm=0.000
Stats 257416.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846174 bytes_read=13328693 bytes_retransmit=9 bytes_invalid=0 send_seq=95927 receive_seq=95927 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004359 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.23 cputime=10462.352 memavail=3557508 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=145.8 pwm=0.000
Stats 257417.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846180 bytes_read=13328901 bytes_retransmit=9 bytes_invalid=0 send_seq=95928 receive_seq=95928 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004271 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.23 cputime=10462.376 memavail=3557700 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=145.1 pwm=0.000
Stats 257418.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846186 bytes_read=13329124 bytes_retransmit=9 bytes_invalid=0 send_seq=95929 receive_seq=95929 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004199 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.45 cputime=10462.407 memavail=3557700 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=144.3 pwm=0.000
Stats 257419.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=846192 bytes_read=13329345 bytes_retransmit=9 bytes_invalid=0 send_seq=95930 receive_seq=95930 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004251 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.45 cputime=10462.431 memavail=3557572 print_time=59239.731 buffer_time=0.000 print_stall=0 extruder: target=220 temp=143.5 pwm=0.000
=======================
Starting Klippy...
Args: ['/home/orangepi/klipper/klippy/klippy.py', '/home/orangepi/printer_data/config/printer.cfg', '-I', '/home/orangepi/printer_data/comms/klippy.serial', '-l', '/home/orangepi/printer_data/logs/klippy.log', '-a', '/home/orangepi/printer_data/comms/klippy.sock']
App Name: Danger-Klipper
Git version: 'v0.12.0-551-gaf6bdd39'
Branch: bleeding-edge-v2
Remote: origin
Tracked URL: https://github.com/DangerKlippers/danger-klipper
CPU: 4 core ?
Python: '3.10.12 (main, Sep 11 2024, 15:47:36) [GCC 11.4.0]'
Start printer at Wed Jan 29 14:17:19 2025 (1738160239.6 28.6)
===== Config file =====
[respond]
[gcode_macro CHOPPER_TUNE]
description = Vibrations tests to calculate lowest magnitude drivers registers v1.2
variable_debug = False
variable_inset = 10
variable_current_change_step = 25
variable_measure_time = 1250
variable_required_rpm = [37.5, 150, 1.5]
variable_delay = 500
variable_fclk = 12
gcode =
{% set current_min = params.CURRENT_MIN_MA|default('default')|string|lower %}
{% set current_max = params.CURRENT_MAX_MA|default('default')|string|lower %}
{% set tbl_min = params.TBL_MIN|default(0)|int %}
{% set tbl_max = params.TBL_MAX|default(3)|int %}
{% set toff_min = params.TOFF_MIN|default(1)|int %}
{% set toff_max = params.TOFF_MAX|default(8)|int %}
{% set hstrt_hend_max = params.HSTRT_HEND_MAX|default(16)|int %}
{% set hstrt_min = params.HSTRT_MIN|default(0)|int %}
{% set hstrt_max = params.HSTRT_MAX|default(7)|int %}
{% set hend_min = params.HEND_MIN|default(2)|int %}
{% set hend_max = params.HEND_MAX|default(15)|int %}
{% set tpfd_min = params.TPFD_MIN|default(-1)|int %}
{% set tpfd_max = params.TPFD_MAX|default(-1)|int %}
{% set min_speed = params.MIN_SPEED|default('default')|string|lower %}
{% set max_speed = params.MAX_SPEED|default('default')|string|lower %}
{% set speed_change_step = params.SPEED_CHANGE_STEP|default('default')|string|lower %}
{% set iterations = params.ITERATIONS|default(1)|int %}
{% set travel_distance = params.TRAVEL_DISTANCE|default('default')|string|lower %}
{% set accel_chip = params.ACCELEROMETER|default('default')|string|lower %}
{% set find_vibr = params.FIND_VIBRATIONS|default('False')|string|lower %}
{% set axis = params.AXIS|default('X')|string|lower %}
{% set run_plotter = params.RUN_PLOTTER|default('True')|string|lower %}
_detect_driver stepper={axis}
_chop_workflow axis={axis} {rawparams}
[gcode_shell_command chop_tune]
command = ~/chopper-resonance-tuner/chopper_plot.sh
timeout = 9999.0
verbose = True
[gcode_macro _detect_driver]
description = Find which driver is used in configuration
variable_drivers = '2130', '2208', '2209', '2660', '2240', '5160'
variable_driver = 0
variable_resistor = 0
gcode =
{% set stepper = 'stepper_' + params.STEPPER|string|lower %}
{% for driver in drivers %}
{% if 'run_current' in printer.configfile.config['tmc' + driver + ' ' + stepper] %}
{action_respond_info('Selected tmc%s for %s' % (driver, stepper))}
SET_GCODE_VARIABLE MACRO=_detect_driver VARIABLE=driver VALUE={driver}
{% if driver != '2240' %}
{% set resistor = printer.configfile.settings['tmc' + driver + ' ' + stepper].sense_resistor %}
{% else %}
{% set resistor = printer.configfile.settings['tmc' + driver + ' ' + stepper].rref %}
{% endif %}
SET_GCODE_VARIABLE MACRO=_detect_driver VARIABLE=resistor VALUE={resistor}
{% endif %}
{% endfor %}
[gcode_macro _chop_apply_regs]
variable_registers = 'tbl', 'toff', 'hend', 'hstrt', 'tpfd', 'curr'
variable_amount = 0
variable_tbl = -1
variable_toff = -1
variable_hend = -1
variable_hstrt = -1
variable_tpfd = -1
variable_curr = -1
gcode =
{% if printer['gcode_macro _chop_apply_regs'][params.FIELD]|int != params.VALUE|int %}
{% for stepper in params.STEPPERS.split('-') %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
M118 Setting {params.FIELD|string|lower} from {
printer['gcode_macro _chop_apply_regs'][params.FIELD]|int} to {params.VALUE|int} on {stepper}
{% endif %}
{% if params.FIELD|lower != 'curr' %}
SET_TMC_FIELD STEPPER={stepper} FIELD={params.FIELD} VALUE={params.VALUE|int}
{% else %}
SET_TMC_CURRENT STEPPER={stepper} CURRENT={params.VALUE|int / 1000}
{% endif %}
{% for count in range(1, amount + 1) %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
M118 Setting {params.FIELD|string|lower} from {
printer['gcode_macro _chop_apply_regs'][params.FIELD]|int} to {
params.VALUE|int} on {stepper|string + count|string}
{% endif %}
{% if params.FIELD|lower != 'curr' %}
SET_TMC_FIELD STEPPER={stepper|string + count|string} FIELD={params.FIELD} VALUE={params.VALUE|int}
{% else %}
SET_TMC_CURRENT STEPPER={stepper} CURRENT={params.VALUE|int / 1000}
{% endif %}
{% endfor %}
{% endfor %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE={params.FIELD|string|lower} VALUE={params.VALUE|int}
{% endif %}
[gcode_macro _chop_workflow]
description = Calculate process of CHOPPER_TUNE macro
gcode =
{% set axis = params.AXIS|default('X')|string|lower %}
{% set driver = printer['gcode_macro _detect_driver'].driver|string|lower %}
{% set sense_resistor = printer['gcode_macro _detect_driver'].resistor %}
{% set current_min = params.CURRENT_MIN_MA|default('default')|string|lower %}
{% set current_max = params.CURRENT_MAX_MA|default('default')|string|lower %}
{% set current_change_step = printer['gcode_macro CHOPPER_TUNE'].current_change_step %}
{% set tbl_min = params.TBL_MIN|default(0)|int %}
{% set tbl_max = params.TBL_MAX|default(3)|int %}
{% set toff_min = params.TOFF_MIN|default(1)|int %}
{% set toff_max = params.TOFF_MAX|default(8)|int %}
{% set hstrt_hend_max = params.HSTRT_HEND_MAX|default(16)|int %}
{% set hstrt_min = params.HSTRT_MIN|default(0)|int %}
{% set hstrt_max = params.HSTRT_MAX|default(7)|int %}
{% set hend_min = params.HEND_MIN|default(2)|int %}
{% set hend_max = params.HEND_MAX|default(15)|int %}
{% set tpfd_min = params.TPFD_MIN|default(-1)|int %}
{% set tpfd_max = params.TPFD_MAX|default(-1)|int %}
{% set min_speed = params.MIN_SPEED|default('default')|string|lower %}
{% set max_speed = params.MAX_SPEED|default('default')|string|lower %}
{% set speed_change_step = params.SPEED_CHANGE_STEP|default('default')|string|lower %}
{% set required_rpm = printer['gcode_macro CHOPPER_TUNE'].required_rpm %}
{% set iterations = params.ITERATIONS|default(1)|int %}
{% set travel_distance = params.TRAVEL_DISTANCE|default('default')|string|lower %}
{% set accel_chip = params.ACCELEROMETER|default('default')|string|lower %}
{% set find_vibr = params.FIND_VIBRATIONS|default('False')|string|lower %}
{% set run_plotter = params.RUN_PLOTTER|default('True')|string|lower %}
{% set inset = printer['gcode_macro CHOPPER_TUNE'].inset %}
{% set config = printer.configfile.config %}
{% set settings = printer.configfile.settings %}
{% set measure_time = printer['gcode_macro CHOPPER_TUNE'].measure_time / 1000|float %}
{% set delay = printer['gcode_macro CHOPPER_TUNE'].delay|int %}
{% set fclk = printer['gcode_macro CHOPPER_TUNE'].fclk|int %}
{% set kinematics = config.printer.kinematics|string %}
{% if axis in ['x', 'y', 'z'] %}
{% if kinematics == 'corexy' %}
{% if axis in ['x', 'y'] %}
{% if axis == 'x' %}
{% set axes = ['x', 'y'] %}
{% elif axis == 'y' %}
{% set axes = ['y', 'x'] %}
{% endif %}
{% set steppers = ['stepper_x', 'stepper_y'] %}
{% elif axis == 'z' %}
{% set axes = ['z', 'x'] %}
{% set steppers = ['stepper_z'] %}
{% endif %}
{% elif kinematics == 'cartesian' %}
{% if axis == 'x' %}
{% set axes = ['x', 'y'] %}
{% set steppers = ['stepper_x'] %}
{% elif axis == 'y' %}
{% set axes = ['y', 'x'] %}
{% set steppers = ['stepper_y'] %}
{% elif axis == 'z' %}
{% set axes = ['z', 'x'] %}
{% set steppers = ['stepper_z'] %}
{% endif %}
{% else %}
{action_raise_error('WARNING!!! Script does not support your kinematics')}
{% endif %}
{% if axes[0] == 'z' %}
{% set minAX = (settings['stepper_' + axes[0]].position_min|float, 0)|max + inset %}
{% set acceleration = settings.printer.max_z_accel|int %}
{% set trv_speed = config.printer.max_z_velocity|int / 2 * 60 %}
{% else %}
{% set minAX = settings['stepper_' + axes[0]].position_min|float + inset %}
{% set acceleration = config.printer.max_accel|int %}
{% set trv_speed = config.printer.max_velocity|int / 2 * 60 %}
{% endif %}
{% set maxAX = settings['stepper_' + axes[0]].position_max|float - inset %}
{% set midAX = settings['stepper_' + axes[0]].position_min|float +
((settings['stepper_' + axes[0]].position_max|float -
settings['stepper_' + axes[0]].position_min|float) / 2) %}
{% set midBAX = settings['stepper_' + axes[1]].position_min|float +
((settings['stepper_' + axes[1]].position_max|float -
settings['stepper_' + axes[1]].position_min|float) / 2) %}
{% else %}
{action_raise_error('WARNING!!! Incorrect direction')}
{% endif %}
{% if tpfd_min != -1 or tpfd_max != -1 %}
{% if driver == '5160' or driver == '2240' %}
{% if tpfd_min < 0 or tpfd_max < 0 %}
{action_raise_error('WARNING!!! Incorrect TPFD values')}
{% endif %}
{% else %}
{action_raise_error('WARNING!!! TMC%s not support register TPFD' % (driver))}
{% endif %}
{% endif %}
{% for register in printer['gcode_macro _chop_apply_regs'].registers %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE={register|string|lower} VALUE=-1
{% endfor %}
{% for mot in range(8) %}
{% if ('stepper_' + axes[0] + mot|string) in config %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE=amount VALUE={mot}
{% if ('stepper_' + axes[0] + (mot + 1)|string) not in config %}
{action_respond_info('Selected %dwd configuration' % (mot + 1))}
{% endif %}
{% elif mot == 1 %}
{action_respond_info('Selected 1wd configuration')}
{% endif %}
{% endfor %}
{% if accel_chip == 'default' %}
{% if 'accel_chip' in config.resonance_tester %}
{% set accel_chip = config.resonance_tester.accel_chip %}
{% else %}
{% set accel_chip = 'adxl345' %}
{% endif %}
{% endif %}
{action_respond_info('Selected %s for accelerometer' % (accel_chip))}
{% if current_min == 'default' %}
{% set current_min = (config['tmc' + driver + ' ' + steppers[0]].run_current|float * 1000)|int %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Set default run_current: %d mA to run_current_min' % (current_min))}
{% endif %}
{% else %}
{% set current_min = current_min|int %}
{% endif %}
{% if current_max == 'default' %}
{% set current_max = (config['tmc' + driver + ' ' + steppers[0]].run_current|float * 1000)|int%}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Set default run_current: %d mA to run_current_max' % (current_max))}
{% endif %}
{% else %}
{% set current_max = current_max|int %}
{% endif %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{% set current_max = current_min %}
{% set tbl_min = settings['tmc' + driver + ' ' + steppers[0]].driver_tbl|int %}
{% set tbl_max = tbl_min %}
{% set toff_min = settings['tmc' + driver + ' ' + steppers[0]].driver_toff|int %}
{% set toff_max = toff_min %}
{% set hstrt_min = settings['tmc' + driver + ' ' + steppers[0]].driver_hstrt|int %}
{% set hstrt_max = hstrt_min %}
{% set hend_min = settings['tmc' + driver + ' ' + steppers[0]].driver_hend|int %}
{% set hend_max = hend_min %}
{% set rotation_dist = config[steppers[0]].rotation_distance|float %}
{% set gear_ratio = (config[steppers[0]].gear_ratio|default('1:1')).split(':') %}
{% set full_steps_per_rotation = config[steppers[0]].full_steps_per_rotation|default(200)|int %}
{% if min_speed == 'default' %}
{% set min_speed = (required_rpm[0] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist)|float %}
{% else %}
{% set min_speed = min_speed|float %}
{% endif %}
{% if max_speed == 'default' %}
{% set max_required_mms = (required_rpm[1] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist)|int %}
{% set max_speed = (((-acceleration * measure_time + ((acceleration * measure_time) ** 2 +
4 * acceleration * (maxAX - minAX)) ** 0.5) / 2), max_required_mms)|min|float %}
{% else %}
{% set max_speed = max_speed|float %}
{% endif %}
{% if speed_change_step == 'default' %}
{% set speed_change_step = required_rpm[2] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist %}
{% else %}
{% set speed_change_step = speed_change_step|float %}
{% endif %}
{% else %}
{% if min_speed == 'default' or max_speed == 'default' %}
{action_raise_error('WARNING!!! Resonance speed must be defined')}
{% endif %}
{% set min_speed, max_speed = min_speed|float, max_speed|float %}
{% set speed_change_step = 1 %}
{% endif %}
{% if max_speed > trv_speed / 30 %}
{action_raise_error('WARNING!!! Required speed (%d mm/s) on axis (%s)'
' is faster than kinematics allow, please lower speed or increase'
' speed limit in printer.cfg' % (max_speed, axes[0]))}
{% endif %}
{% set accel_decel_distance = max_speed ** 2 / acceleration %}
{% set auto_travel_distance = accel_decel_distance + (max_speed * measure_time) %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Acceleration & deceleration zone = %f mm' % (accel_decel_distance))}
{action_respond_info('Auto calculated min required travel distance = %f mm' % (auto_travel_distance))}
{% endif %}
{% if travel_distance == 'default' %}
{% if minAX + auto_travel_distance > maxAX %}
{action_raise_error('WARNING!!! Required travel distance on axis (%s)'
' (%.2f mm) is longer than kinematics allows, please lower'
' speed or increase acceleration' % (axes[0], auto_travel_distance))}
{% endif %}
{% set travel_distance = auto_travel_distance %}
{% else %}
{% set travel_distance = travel_distance|int %}
{% if minAX + travel_distance > maxAX %}
{% set travel_distance = maxAX - minAX %}
{% if travel_distance < auto_travel_distance %}
{action_raise_error('WARNING!!! Travel distance on axis (%s) is less than'
' it should be, please increase acceleration or lower speed' % (axes[0]))}
{% else %}
{action_respond_info('WARNING!!! Travel distance on axis (%s)'
' is longer than kinematics allows, lowering...' % (axes[0]))}
{% endif %}
{% else %}
{% if travel_distance < auto_travel_distance %}
{% set travel_distance = auto_travel_distance %}
{% if minAX + auto_travel_distance > maxAX %}
{action_raise_error('WARNING!!! Travel distance on axis (%s) is less'
' than required (%.2f mm), and longer than kinematics allows, please lower'
' speed or increase acceleration' % (axes[0], auto_travel_distance))}
{% endif %}
{% endif %}
{% endif %}
{% endif %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{action_respond_info('Final max travel distance = %.2f mm, position min = %.2f, traveling: %.2f --> %.2f' %
(travel_distance, minAX, minAX, travel_distance + minAX))}
{action_respond_info('Start find vibration mode, speed: %.2f --> %.2f mm/s with %.2f step current=%d TBL=%d TOFF=%d'
' HSTRT=%d HEND=%d' % (min_speed, max_speed, speed_change_step, current_min, tbl_min, toff_min, hstrt_min, hend_min))}
{% else %}
{action_respond_info('Final travel distance = %.2f mm, position min = %.2f, traveling: %.2f --> %.2f' %
(travel_distance, minAX, minAX, travel_distance + minAX))}
{action_respond_info('Start of register enumeration mode, speed: %.2f --> %.2f mm/s current: %d'
' --> %d mA iterations=%d TBL: %d --> %d TOFF: %d --> %d HSTRT: %d --> %d HEND: %d --> %d TPFD:'
' %d --> %d' % (min_speed, max_speed, current_min, current_max, iterations, tbl_min, tbl_max,
toff_min, toff_max, hstrt_min, hstrt_max, hend_min, hend_max, tpfd_min, tpfd_max))}
{% endif %}
{% if not 'xyz' in printer.toolhead.homed_axes %}
G28 X Y Z
{% endif %}
SET_VELOCITY_LIMIT ACCEL={acceleration}
SET_VELOCITY_LIMIT ACCEL_TO_DECEL={acceleration}
G0 {axes[0]}{minAX} {axes[1]}{midBAX} F{trv_speed}
RUN_SHELL_COMMAND CMD=chop_tune PARAMS='cleaner'
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME=stand_still
G4 P5000
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME=stand_still
{% for current in range(current_min, current_max + 1, current_change_step) %}
_chop_apply_regs steppers={steppers|join('-')} field=curr value={current}
{% for tbl in range(tbl_min, tbl_max + 1) %}
_chop_apply_regs steppers={steppers|join('-')} field=tbl value={tbl}
{% for toff in range(toff_min, toff_max + 1) %}
_chop_apply_regs steppers={steppers|join('-')} field=toff value={toff}
{% for hstrt_value in range(hstrt_min, hstrt_max + 1) %}
{% for hend_value in range(hend_min, hend_max + 1) %}
{% if hend_value + hstrt_value <= hstrt_hend_max %}
_chop_apply_regs steppers={steppers|join('-')} field=hend value={hend_value}
_chop_apply_regs steppers={steppers|join('-')} field=hstrt value={hstrt_value}
{% for tpfd in range(tpfd_min, tpfd_max + 1) %}
{% if tpfd_min != -1 and tpfd_max != -1 %}
_chop_apply_regs steppers={steppers|join('-')} field=tpfd value={tpfd}
{% endif %}
DUMP_TMC STEPPER={steppers[0]} REGISTER=chopconf
{% set freq = 1/(2*(12+32*toff)*1/(1000000*fclk)+2*1/(1000000*fclk)*16*(1.5**tbl)) %}
{% for speed in range((min_speed * 100)|int, (max_speed * 100)|int + 1, (speed_change_step * 100)|int) %}
{% set speed = speed / 100 %}
{% for i in range(iterations) %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{% set travel_distance = (travel_distance / max_speed) * speed %}
G4 P{delay}
M118 Speed {speed|round(2)} mm/s on {travel_distance|round(2)} mm
{% endif %}
{% set name = '__%d_%d_%d_%d_%d_%d_%d_%d_%d__' %
(current, tbl, toff, hstrt_value, hend_value, tpfd, speed*100, freq, i+1) %}
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME={name}
G0 {axes[0]}{minAX + travel_distance} F{speed*60}
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME={name}
G0 {axes[0]}{minAX} F{trv_speed}
M400
{% endfor %}
{% endfor %}
{% endfor %}
{% endif %}
{% endfor %}
{% endfor %}
{% endfor %}
{% endfor %}
{% endfor %}
{% if tpfd_min == -1 or tpfd_max == -1 %}
{% set tpfd_min, tpfd_max = 0, 0 %}
{% endif %}
G4 P500
G0 {axis}{midAX} F{trv_speed}
{% if run_plotter == 'true' or run_plotter == '1' %}
M118 Magnitude graphs generation...
M118 This may take a while, please wait
RUN_SHELL_COMMAND CMD=chop_tune PARAMS='{'iterations=%d driver=%s sense_resistor=%f'%(iterations, driver, sense_resistor)}'
{% endif %}
M118 For run parser manually type - RUN_SHELL_COMMAND CMD=chop_tune PARAMS='{'iterations=%d driver=%s sense_resistor=%f'%
(iterations, driver, sense_resistor)}'
[virtual_sdcard]
path = ~/printer_data/gcodes
on_error_gcode = CANCEL_PRINT
[pause_resume]
[display_status]
[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = BASE_CANCEL_PRINT
gcode =
TURN_OFF_HEATERS
CLEAR_PAUSE
SDCARD_RESET_FILE
BASE_CANCEL_PRINT
G90
G0 X350 Y350 F3600
SET_SKEW CLEAR=1
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=0
[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set idle_timeout = client.idle_timeout|default(0) %}
{% set temp = printer[printer.toolhead.extruder].target if printer.toolhead.extruder != '' else 0 %}
{% set restore = False if printer.toolhead.extruder == ''
else True if params.RESTORE|default(1)|int == 1 else False %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=last_extruder_temp VALUE="{{'restore': restore, 'temp': temp}}"
{% if idle_timeout > 0 %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=restore_idle_timeout VALUE={printer.configfile.settings.idle_timeout.timeout}
SET_IDLE_TIMEOUT TIMEOUT={idle_timeout}
{% endif %}
PAUSE_BASE
{client.user_pause_macro|default("")}
_TOOLHEAD_PARK_PAUSE_CANCEL {rawparams}
[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
variable_last_extruder_temp = {'restore': False, 'temp': 0}
variable_restore_idle_timeout = 0
variable_idle_state = False
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set sp_move = client.speed_move|default(velocity) %}
{% set runout_resume = True if client.runout_sensor|default("") == ""
else True if not printer[client.runout_sensor].enabled
else printer[client.runout_sensor].filament_detected %}
{% set can_extrude = True if printer.toolhead.extruder == ''
else printer[printer.toolhead.extruder].can_extrude %}
{% set do_resume = False %}
{% set prompt_txt = [] %}
{% if printer.idle_timeout.state|upper == "IDLE" or idle_state %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=idle_state VALUE=False
{% if last_extruder_temp.restore %}
RESPOND TYPE=echo MSG='{"Restoring \"%s\" temperature to %3.1f\u00B0C, this may take some time" % (printer.toolhead.extruder, last_extruder_temp.temp) }'
M109 S{last_extruder_temp.temp}
{% set do_resume = True %}
{% elif can_extrude %}
{% set do_resume = True %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}'
{% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %}
{% endif %}
{% elif can_extrude %}
{% set do_resume = True %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}'
{% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %}
{% endif %}
{% if runout_resume %}
{% if do_resume %}
{% if restore_idle_timeout > 0 %} SET_IDLE_TIMEOUT TIMEOUT={restore_idle_timeout} {% endif %}
{client.user_resume_macro|default("")}
_CLIENT_EXTRUDE
RESUME_BASE VELOCITY={params.VELOCITY|default(sp_move)}
{% endif %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]}'
{% set _d = prompt_txt.append("\"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]) %}
{% endif %}
{% if not (runout_resume and do_resume) %}
RESPOND TYPE=command MSG="action:prompt_begin RESUME aborted !!!"
{% for element in prompt_txt %}
RESPOND TYPE=command MSG='{"action:prompt_text %s" % element}'
{% endfor %}
RESPOND TYPE=command MSG="action:prompt_footer_button Ok|RESPOND TYPE=command MSG=action:prompt_end|info"
RESPOND TYPE=command MSG="action:prompt_show"
{% endif %}
[gcode_macro SET_PAUSE_NEXT_LAYER]
description = Enable a pause if the next layer is reached
gcode =
{% set pause_next_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_next_layer %}
{% set ENABLE = params.ENABLE|default(1)|int != 0 %}
{% set MACRO = params.MACRO|default(pause_next_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_next_layer VALUE="{{ 'enable': ENABLE, 'call': MACRO }}"
[gcode_macro SET_PAUSE_AT_LAYER]
description = Enable/disable a pause if a given layer number is reached
gcode =
{% set pause_at_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_at_layer %}
{% set ENABLE = params.ENABLE|int != 0 if params.ENABLE is defined
else params.LAYER is defined %}
{% set LAYER = params.LAYER|default(pause_at_layer.layer)|int %}
{% set MACRO = params.MACRO|default(pause_at_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_at_layer VALUE="{{ 'enable': ENABLE, 'layer': LAYER, 'call': MACRO }}"
[gcode_macro SET_PRINT_STATS_INFO]
rename_existing = SET_PRINT_STATS_INFO_BASE
description = Overwrite, to get pause_next_layer and pause_at_layer feature
variable_pause_next_layer = { 'enable': False, 'call': "PAUSE" }
variable_pause_at_layer = { 'enable': False, 'layer': 0, 'call': "PAUSE" }
gcode =
{% if pause_next_layer.enable %}
RESPOND TYPE=echo MSG='{"%s, forced by pause_next_layer" % pause_next_layer.call}'
{pause_next_layer.call}
SET_PAUSE_NEXT_LAYER ENABLE=0
{% elif pause_at_layer.enable and params.CURRENT_LAYER is defined and params.CURRENT_LAYER|int == pause_at_layer.layer %}
RESPOND TYPE=echo MSG='{"%s, forced by pause_at_layer [%d]" % (pause_at_layer.call, pause_at_layer.layer)}'
{pause_at_layer.call}
SET_PAUSE_AT_LAYER ENABLE=0
{% endif %}
SET_PRINT_STATS_INFO_BASE {rawparams}
[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL]
description = Helper: park toolhead used in PAUSE and CANCEL_PRINT
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set use_custom = client.use_custom_pos|default(false)|lower == 'true' %}
{% set custom_park_x = client.custom_park_x|default(0.0) %}
{% set custom_park_y = client.custom_park_y|default(0.0) %}
{% set park_dz = client.custom_park_dz|default(2.0)|abs %}
{% set sp_hop = client.speed_hop|default(15) * 60 %}
{% set sp_move = client.speed_move|default(velocity) * 60 %}
{% set origin = printer.gcode_move.homing_origin %}
{% set act = printer.gcode_move.gcode_position %}
{% set max = printer.toolhead.axis_maximum %}
{% set cone = printer.toolhead.cone_start_z|default(max.z) %}
{% set round_bed = True if printer.configfile.settings.printer.kinematics is in ['delta','polar','rotary_delta','winch']
else False %}
{% set z_min = params.Z_MIN|default(0)|float %}
{% set z_park = [[(act.z + park_dz), z_min]|max, (max.z - origin.z)]|min %}
{% set x_park = params.X if params.X is defined
else custom_park_x if use_custom
else 0.0 if round_bed
else (max.x - 5.0) %}
{% set y_park = params.Y if params.Y is defined
else custom_park_y if use_custom
else (max.y - 5.0) if round_bed and z_park < cone
else 0.0 if round_bed
else (max.y - 5.0) %}
_CLIENT_RETRACT
{% if "xyz" in printer.toolhead.homed_axes %}
G90
G1 Z{z_park} F{sp_hop}
G1 X{x_park} Y{y_park} F{sp_move}
{% if not printer.gcode_move.absolute_coordinates %} G91 {% endif %}
{% else %}
RESPOND TYPE=echo MSG='Printer not homed'
{% endif %}
[gcode_macro _CLIENT_EXTRUDE]
description = Extrudes, if the extruder is hot enough
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set use_fw_retract = (client.use_fw_retract|default(false)|lower == 'true') and (printer.firmware_retraction is defined) %}
{% set length = params.LENGTH|default(client.unretract)|default(1.0)|float %}
{% set speed = params.SPEED|default(client.speed_unretract)|default(35) %}
{% set absolute_extrude = printer.gcode_move.absolute_extrude %}
{% if printer.toolhead.extruder != '' %}
{% if printer[printer.toolhead.extruder].can_extrude %}
{% if use_fw_retract %}
{% if length < 0 %}
G10
{% else %}
G11
{% endif %}
{% else %}
M83
G1 E{length} F{(speed|float|abs) * 60}
{% if absolute_extrude %}
M82
{% endif %}
{% endif %}
{% else %}
RESPOND TYPE=echo MSG='{"\"%s\" not hot enough" % printer.toolhead.extruder}'
{% endif %}
{% endif %}
[gcode_macro _CLIENT_RETRACT]
description = Retracts, if the extruder is hot enough
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set length = params.LENGTH|default(client.retract)|default(1.0)|float %}
{% set speed = params.SPEED|default(client.speed_retract)|default(35) %}
_CLIENT_EXTRUDE LENGTH=-{length|float|abs} SPEED={speed|float|abs}
[autotune_tmc stepper_x]
motor = omc-17me15-1504s
tuning_goal = performance
voltage = 48
tbl = 0
toff = 1
[autotune_tmc stepper_y]
motor = omc-17me15-1504s
tuning_goal = performance
voltage = 48
tbl = 0
toff = 1
[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE
gcode =
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set bed_mesh_min = printer.configfile.settings.bed_mesh.mesh_min %}
{% set bed_mesh_max = printer.configfile.settings.bed_mesh.mesh_max %}
{% set probe_count = printer.configfile.settings.bed_mesh.probe_count %}
{% set kamp_settings = printer["gcode_macro _KAMP_Settings"] %}
{% set verbose_enable = kamp_settings.verbose_enable | abs %}
{% set probe_dock_enable = kamp_settings.probe_dock_enable | abs %}
{% set attach_macro = kamp_settings.attach_macro | string %}
{% set detach_macro = kamp_settings.detach_macro | string %}
{% set mesh_margin = kamp_settings.mesh_margin | float %}
{% set fuzz_amount = kamp_settings.fuzz_amount | float %}
{% set probe_count = probe_count if probe_count|length > 1 else probe_count * 2 %}
{% set max_probe_point_distance_x = ( bed_mesh_max[0] - bed_mesh_min[0] ) / (probe_count[0] - 1) %}
{% set max_probe_point_distance_y = ( bed_mesh_max[1] - bed_mesh_min[1] ) / (probe_count[1] - 1) %}
{% set x_min = all_points | map(attribute=0) | min | default(bed_mesh_min[0]) %}
{% set y_min = all_points | map(attribute=1) | min | default(bed_mesh_min[1]) %}
{% set x_max = all_points | map(attribute=0) | max | default(bed_mesh_max[0]) %}
{% set y_max = all_points | map(attribute=1) | max | default(bed_mesh_max[1]) %}
{% set fuzz_range = range((0) | int, (fuzz_amount * 100) | int + 1) %}
{% set adapted_x_min = x_min - mesh_margin - (fuzz_range | random / 100.0) %}
{% set adapted_y_min = y_min - mesh_margin - (fuzz_range | random / 100.0) %}
{% set adapted_x_max = x_max + mesh_margin + (fuzz_range | random / 100.0) %}
{% set adapted_y_max = y_max + mesh_margin + (fuzz_range | random / 100.0) %}
{% set adapted_x_min = [adapted_x_min , bed_mesh_min[0]] | max %}
{% set adapted_y_min = [adapted_y_min , bed_mesh_min[1]] | max %}
{% set adapted_x_max = [adapted_x_max , bed_mesh_max[0]] | min %}
{% set adapted_y_max = [adapted_y_max , bed_mesh_max[1]] | min %}
{% set points_x = (((adapted_x_max - adapted_x_min) / max_probe_point_distance_x) | round(method='ceil') | int) + 1 %}
{% set points_y = (((adapted_y_max - adapted_y_min) / max_probe_point_distance_y) | round(method='ceil') | int) + 1 %}
{% if (([points_x, points_y]|max) > 6) %}
{% set algorithm = "bicubic" %}
{% set min_points = 4 %}
{% else %}
{% set algorithm = "lagrange" %}
{% set min_points = 3 %}
{% endif %}
{% set points_x = [points_x , min_points]|max %}
{% set points_y = [points_y , min_points]|max %}
{% set points_x = [points_x , probe_count[0]]|min %}
{% set points_y = [points_y , probe_count[1]]|min %}
{% if verbose_enable == True %}
{% if printer.exclude_object.objects != [] %}
{ action_respond_info( "Algorithm: {}.".format(
(algorithm),
)) }
{ action_respond_info("Default probe count: {},{}.".format(
(probe_count[0]),
(probe_count[1]),
)) }
{ action_respond_info("Adapted probe count: {},{}.".format(
(points_x),
(points_y),
)) }
{action_respond_info("Default mesh bounds: {}, {}.".format(
(bed_mesh_min[0],bed_mesh_min[1]),
(bed_mesh_max[0],bed_mesh_max[1]),
)) }
{% if mesh_margin > 0 %}
{action_respond_info("Mesh margin is {}, mesh bounds extended by {}mm.".format(
(mesh_margin),
(mesh_margin),
)) }
{% else %}
{action_respond_info("Mesh margin is 0, margin not increased.")}
{% endif %}
{% if fuzz_amount > 0 %}
{action_respond_info("Mesh point fuzzing enabled, points fuzzed up to {}mm.".format(
(fuzz_amount),
)) }
{% else %}
{action_respond_info("Fuzz amount is 0, mesh points not fuzzed.")}
{% endif %}
{ action_respond_info("Adapted mesh bounds: {}, {}.".format(
(adapted_x_min, adapted_y_min),
(adapted_x_max, adapted_y_max),
)) }
{action_respond_info("KAMP adjustments successful. Happy KAMPing!")}
{% else %}
{action_respond_info("No objects detected! Check your gcode and make sure that EXCLUDE_OBJECT_DEFINE is happening before BED_MESH_CALIBRATE is called. Defaulting to regular meshing.")}
G4 P5000
{% endif %}
{% endif %}
{% if probe_dock_enable == True %}
{attach_macro}
{% endif %}
_BED_MESH_CALIBRATE mesh_min={adapted_x_min},{adapted_y_min} mesh_max={adapted_x_max},{adapted_y_max} ALGORITHM={algorithm} PROBE_COUNT={points_x},{points_y}
{% if probe_dock_enable == True %}
{detach_macro}
{% endif %}
[gcode_macro LINE_PURGE]
description = A purge macro that adapts to be near your actual printed objects
gcode =
{% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
{% set cross_section = printer.configfile.settings.extruder.max_extrude_cross_section | float %}
{% if printer.firmware_retraction is defined %}
{% set RETRACT = G10 | string %}
{% set UNRETRACT = G11 | string %}
{% else %}
{% set RETRACT = 'G1 E-.5 F2100' | string %}
{% set UNRETRACT = 'G1 E.5 F2100' | string %}
{% endif %}
{% set verbose_enable = printer["gcode_macro _KAMP_Settings"].verbose_enable | abs %}
{% set purge_height = printer["gcode_macro _KAMP_Settings"].purge_height | float %}
{% set tip_distance = printer["gcode_macro _KAMP_Settings"].tip_distance | float %}
{% set purge_margin = printer["gcode_macro _KAMP_Settings"].purge_margin | float %}
{% set purge_amount = printer["gcode_macro _KAMP_Settings"].purge_amount | float %}
{% set flow_rate = printer["gcode_macro _KAMP_Settings"].flow_rate | float %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set purge_x_min = (all_points | map(attribute=0) | min | default(0)) %}
{% set purge_x_max = (all_points | map(attribute=0) | max | default(0)) %}
{% set purge_y_min = (all_points | map(attribute=1) | min | default(0)) %}
{% set purge_y_max = (all_points | map(attribute=1) | max | default(0)) %}
{% set purge_x_center = ([((purge_x_max + purge_x_min) / 2) - (purge_amount / 2), 0] | max) %}
{% set purge_y_center = ([((purge_y_max + purge_y_min) / 2) - (purge_amount / 2), 0] | max) %}
{% set purge_x_origin = ([purge_x_min - purge_margin, 0] | max) %}
{% set purge_y_origin = ([purge_y_min - purge_margin, 0] | max) %}
{% set purge_move_speed = (flow_rate / 5.0) * 60 | float %}
{% if cross_section < 5 %}
{action_respond_info("[Extruder] max_extrude_cross_section is insufficient for purge, please set it to 5 or greater. Purge skipped.")}
{% else %}
{% if verbose_enable == True %}
{action_respond_info("Moving filament tip {}mms".format(
(tip_distance),
)) }
{% endif %}
{% if printer.firmware_retraction is defined %}
{action_respond_info("KAMP purge is using firmware retraction.")}
{% else %}
{action_respond_info("KAMP purge is not using firmware retraction, it is recommended to configure it.")}
{% endif %}
{% if purge_y_origin > 0 %}
{action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm3/s.".format(
(purge_x_center),
(purge_y_origin),
(purge_amount),
(flow_rate),
)) }
{% else %}
{action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm3/s.".format(
(purge_x_origin),
(purge_y_center),
(purge_amount),
(flow_rate),
)) }
{% endif %}
SAVE_GCODE_STATE NAME=Prepurge_State
{% if purge_y_origin > 0 %}
G92 E0
G0 F{travel_speed}
G90
G0 X{purge_x_center} Y{purge_y_origin}
G0 Z{purge_height}
M83
G1 E{tip_distance} F{purge_move_speed}
G1 X{purge_x_center + purge_amount} E{purge_amount} F{purge_move_speed}
{RETRACT}
G0 X{purge_x_center + purge_amount + 10} F{travel_speed}
G92 E0
M82
G0 Z{purge_height * 2} F{travel_speed}
{% else %}
G92 E0
G0 F{travel_speed}
G90
G0 X{purge_x_origin} Y{purge_y_center}
G0 Z{purge_height}
M83
G1 E{tip_distance} F{purge_move_speed}
G1 Y{purge_y_center + purge_amount} E{purge_amount} F{purge_move_speed}
{RETRACT}
G0 Y{purge_y_center + purge_amount + 10} F{travel_speed}
G92 E0
M82
G0 Z{purge_height * 2} F{travel_speed}
{% endif %}
RESTORE_GCODE_STATE NAME=Prepurge_State
{% endif %}
[gcode_macro SMART_PARK]
description = Parks your printhead near the print area for pre-print hotend heating.
gcode =
{% set kamp_settings = printer["gcode_macro _KAMP_Settings"] %}
{% set z_height = kamp_settings.smart_park_height | float %}
{% set purge_margin = kamp_settings.purge_margin | float %}
{% set verbose_enable = kamp_settings.verbose_enable | abs %}
{% set center_x = printer.toolhead.axis_maximum.x / 2 | float %}
{% set center_y = printer.toolhead.axis_maximum.y / 2 | float %}
{% set axis_minimum_x = printer.toolhead.axis_minimum.x | float %}
{% set axis_minimum_y = printer.toolhead.axis_minimum.y | float %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set x_min = all_points | map(attribute=0) | min | default(center_x) %}
{% set y_min = all_points | map(attribute=1) | min | default(center_y) %}
{% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
{% if purge_margin > 0 and x_min != center_x and y_min != center_y %}
{% set x_min = [ x_min - purge_margin , x_min ] | min %}
{% set y_min = [ y_min - purge_margin , y_min ] | min %}
{% set x_min = [ x_min , axis_minimum_x ] | max %}
{% set y_min = [ y_min , axis_minimum_y ] | max %}
{% endif %}
{% if verbose_enable == True %}
{ action_respond_info("Smart Park location: {},{}.".format(
(x_min),
(y_min),
)) }
{% endif %}
SAVE_GCODE_STATE NAME=Presmartpark_State
G90
{% if printer.toolhead.position.z < z_height %}
G0 Z{z_height}
{% endif %}
G0 X{x_min} Y{y_min} F{travel_speed}
G0 Z{z_height}
RESTORE_GCODE_STATE NAME=Presmartpark_State
[gcode_macro _KAMP_Settings]
description = This macro contains all adjustable settings for KAMP
variable_verbose_enable = True
variable_mesh_margin = 5
variable_fuzz_amount = 0
variable_probe_dock_enable = False
variable_attach_macro = 'Attach_Probe'
variable_detach_macro = 'Dock_Probe'
variable_purge_height = 0.8
variable_tip_distance = 0
variable_purge_margin = 10
variable_purge_amount = 30
variable_flow_rate = 12
variable_smart_park_height = 10
gcode =
{action_respond_info(" Running the KAMP_Settings macro does nothing, it is only used for storing KAMP settings. ")}
[gcode_macro _TAP_VARIABLES]
variable_probing = 0
variable_brushed = 0
gcode =
[gcode_macro _PRE_PROBE_CHECK]
gcode =
{% set svv = printer.save_variables.variables %}
{% set PROBE_TEMP = svv.probe_temp %}
{% set MAX_TEMP = PROBE_TEMP + 5 %}
{% set ACTUAL_TEMP = printer.extruder.temperature %}
{% set TARGET_TEMP = printer.extruder.target %}
{% set PROBE_ACCEL = printer["gcode_macro _TAP_SETTINGS"].probe_accel %}
{% set BRUSHED = printer["gcode_macro _TAP_VARIABLES"].brushed %}
{% if BRUSHED == 1 %}
_PROBE_TEMP_CHECK
{% else %}
NOZZLE_BRUSH
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=1
_PROBE_TEMP_CHECK
{% endif %}
[gcode_macro _PROBE_TEMP_CHECK]
gcode =
{% set svv = printer.save_variables.variables %}
{% set PROBE_TEMP = svv.probe_temp %}
{% set MAX_TEMP = PROBE_TEMP + 5 %}
{% set ACTUAL_TEMP = printer.extruder.temperature %}
{% set TARGET_TEMP = printer.extruder.target %}
{% set PROBE_ACCEL = printer["gcode_macro _TAP_SETTINGS"].probe_accel %}
SET_KINEMATICS_LIMIT Z_ACCEL={PROBE_ACCEL}
{% if TARGET_TEMP > PROBE_TEMP %}
{ action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
M109 S{PROBE_TEMP}
{% else %}
{% if ACTUAL_TEMP > MAX_TEMP %}
{ action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={MAX_TEMP}
{% endif %}
{% endif %}
[gcode_macro _POST_PROBING]
gcode =
SET_KINEMATICS_LIMIT Z_ACCEL={printer["gcode_macro _TAP_SETTINGS"].max_z_accel}
[gcode_macro _POST_PROBE]
gcode =
POST_PROBE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
[gcode_macro SET_PROBE_TEMP]
gcode =
{% set temp = params.TEMP|int %}
SAVE_VARIABLE VARIABLE=probe_temp VALUE={TEMP}
[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_REAL
gcode =
Z_TILT_ADJUST_REAL
POST_PROBE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
[gcode_macro _TAP_SETTINGS]
variable_probe_accel = 15
variable_home_x = 175
variable_home_y = 175
variable_home_speed = 100
variable_max_z_accel = 30
gcode =
[mcu]
serial = /dev/serial/by-id/usb-Klipper_stm32f446xx_JKYZ-if00
[danger_options]
allow_plugin_override = True
[printer]
square_corner_velocity = 500.0
kinematics = limited_corexy
max_velocity = 564
max_z_velocity = 30
max_accel = 20000
max_x_accel = 20000
max_y_accel = 19000
max_z_accel = 30
scale_xy_accel = True
[thermistor NTC10K]
temperature1 = 0.0
resistance1 = 32116.0
temperature2 = 40.0
resistance2 = 5309.0
temperature3 = 80.0
resistance3 = 1228.0
[stepper_y]
step_pin = PE11
dir_pin = PE10
enable_pin = !PE9
rotation_distance = 40
microsteps = 32
full_steps_per_rotation = 200
endstop_pin = PB13
position_min = 0
position_endstop = 350
position_max = 350
homing_speed = 60
homing_retract_dist = 0
homing_positive_dir = true
step_pulse_duration = 0.000004
[tmc5160 stepper_y]
cs_pin = PE7
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = true
run_current = 1.3
sense_resistor = 0.033
driver_tbl = 0
driver_toff = 1
driver_hstrt = 0
driver_hend = 10
driver_tpfd = 1
[stepper_x]
step_pin = PD8
dir_pin = PB12
enable_pin = !PD9
rotation_distance = 40
microsteps = 32
full_steps_per_rotation = 200
endstop_pin = PB14
position_min = 0
step_pulse_duration = 0.000004
position_endstop = 350
position_max = 350
homing_speed = 60
homing_retract_dist = 0
homing_positive_dir = true
[tmc5160 stepper_x]
cs_pin = PE15
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = true
run_current = 1.3
sense_resistor = 0.033
driver_tbl = 0
driver_toff = 1
driver_hstrt = 0
driver_hend = 10
driver_tpfd = 1
[stepper_z]
step_pin = PE2
dir_pin = PE4
enable_pin = !PE3
rotation_distance = 4
microsteps = 32
endstop_pin = probe:z_virtual_endstop
position_max = 290
position_min = -5
homing_speed = 50
second_homing_speed = 10
homing_retract_dist = 3
[tmc2209 stepper_z]
uart_pin = PC15
uart_address = 0
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[stepper_z1]
step_pin = PE1
dir_pin = PE0
enable_pin = !PC5
rotation_distance = 4
microsteps = 32
[tmc2209 stepper_z1]
uart_pin = PD11
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[stepper_z2]
step_pin = PD12
dir_pin = PC4
enable_pin = !PE8
rotation_distance = 4
microsteps = 32
[tmc2209 stepper_z2]
uart_pin = PA15
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[extruder]
step_pin = PE6
dir_pin = !PC13
enable_pin = !PE5
rotation_distance = 4.637
microsteps = 16
full_steps_per_rotation = 200
nozzle_diameter = 0.600
filament_diameter = 1.75
heater_pin = PB15
sensor_type = PT1000
sensor_pin = PC0
min_temp = 10
max_temp = 315
max_power = 1.0
min_extrude_temp = 170
heater_power = 65
cooling_fan = fan_generic fan0
ambient_temp_sensor = heater_generic chamber_heater
pressure_advance = 0.05
pressure_advance_smooth_time = 0.040
max_extrude_cross_section = 5
pid_version = 1
pid_target = 285.00
pid_tolerance = 0.0200
pid_kp = 18.086
pid_ki = 0.536
pid_kd = 152.599
control = mpc
block_heat_capacity = 16.6237
sensor_responsiveness = 0.0731558
ambient_transfer = 0.110661
fan_ambient_transfer = 0.110661, 0.194043, 0.24027
[tmc5160 extruder]
cs_pin = PC14
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = True
run_current = 0.5
hold_current = 0.5
sense_resistor = 0.033
[verify_heater extruder]
hysteresis = 20
heating_gain = 0.2
check_gain_time = 120
[heater_bed]
heater_pin = PB3
sensor_type = Generic 3950
sensor_pin = PC1
max_power = 0.8
min_temp = 5
max_temp = 170
pid_version = 1
pid_target = 105.00
pid_tolerance = 0.0200
control = pid
pid_kp = 51.427
pid_ki = 1.894
pid_kd = 349.061
[probe]
pin = PA3
x_offset = 0
y_offset = 0
speed = 50.0
samples = 4
samples_result = median
sample_retract_dist = 3.0
samples_tolerance = 0.1
samples_tolerance_retries = 5
deactivate_on_each_sample = True
activate_gcode =
_PRE_PROBE_CHECK
deactivate_gcode =
_POST_PROBING
z_offset = -1.930
[safe_z_home]
home_xy_position = 175, 175
z_hop = 5
[heater_fan hotend_fan]
pin = PA13
max_power = 1.0
kick_start_time = 0.5
heater = extruder
heater_temp = 50.0
fan_speed = 1.0
[fan_generic fan0]
pin = PA8
max_power = 1.0
kick_start_time = 0.1
off_below = 0.05
cycle_time = 0.00005
[idle_timeout]
timeout = 9999999999
[bed_mesh]
speed = 100
horizontal_move_z = 10
mesh_min = 40, 40
mesh_max = 310,310
fade_start = 0.6
fade_end = 10.0
probe_count = 7,7
algorithm = bicubic
adaptive_margin = 5
[z_tilt]
z_positions =
-50, 18
150, 348
350, 18
points =
30, 5
175, 295
320, 5
speed = 100
horizontal_move_z = 10
retries = 10
retry_tolerance = 0.007
[gcode_macro G32]
gcode =
BED_MESH_CLEAR
G28
Z_TILT_ADJUST
G28
G0 X175 Y175 Z30 F3600
[save_variables]
filename = ~/printer_data/config/variables.cfg
[gcode_macro _PREHEAT]
gcode =
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={printer.extruder.filament.extruder}
SET_HEATER_TEMPERATURE HEATER=bed TARGET={printer.extruder.filament.bed}
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={printer.extruder.filament.chamber}
[gcode_macro _COOLOFF]
gcode =
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=0
SET_HEATER_TEMPERATURE HEATER=bed TARGET=0
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
SET_FAN_SPEED FAN=fan2 SPEED=1.0
[gcode_macro PRINT_START]
gcode =
{% set chamber = printer.extruder.filament.chamber %}
SET_FAN_SPEED FAN=fan0 SPEED=0.0
SET_FAN_SPEED FAN=fan2 SPEED=0.0
G28
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={printer.extruder.filament.chamber}
TEMPERATURE_WAIT SENSOR="heater_generic chamber_heater" MINIMUM={printer.extruder.filament.chamber}
SET_HEATER_TEMPERATURE HEATER=chamber_heater target=0
G28 Z
BED_MESH_CALIBRATE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
G92 E0
G90
LINE_PURGE
[gcode_macro PRINT_END]
gcode =
M400
G92 E0
G1 E-1.0 F3600
G91
G0 Z1.00 X20.0 Y20.0 F20000
TURN_OFF_HEATERS
M107
G90
G0 X350 Y350 F3600
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=0
[exclude_object]
[gcode_arcs]
resolution = 0.1
[input_shaper]
smoother_freq_x = 56.6
smoother_freq_y = 30.8
shaper_type_x = smooth_zvd_ei
shaper_freq_x = 41.6
shaper_type_y = smooth_ei
shaper_freq_y = 26.6
[filaments]
on_set_filament_gcode =
M117 add
on_clear_filament_gcode =
M117 clear
[z_thermal_adjust]
temp_coeff = 0.005
smooth_time = 1
sensor_type = NTC10K
sensor_pin = PB0
min_temp = 10
max_temp = 77
gcode_id = thermal_adjust
[led led_strip]
red_pin = PB6
green_pin = PB5
blue_pin = PB7
[heater_generic chamber_heater]
heater_pin = PC8
max_power = 1.0
sensor_type = Generic 3950
sensor_pin = PB1
min_temp = 10
max_temp = 75
pid_version = 1
pid_target = 60.00
pid_tolerance = 0.0200
control = pid
pid_kp = 64.228
pid_ki = 0.421
pid_kd = 2450.039
[heater_fan chamber_heater_fan]
pin = PB2
max_power = 1.0
heater = chamber_heater
heater_temp = 35
[verify_heater chamber_heater]
hysteresis = 10
heating_gain = 0.1
check_gain_time = 600
[fan_generic fan2]
pin = !PD1
cycle_time = 0.00005
kick_start_time = 0.1
off_below = 0.07
[gcode_macro M106]
gcode =
{% set fan = 'fan' + (params.P|int if params.P is defined else 0)|string %}
{% set speed = (params.S|float / 255 if params.S is defined else 1.0) %}
SET_FAN_SPEED FAN={fan} SPEED={speed}
[gcode_macro _ENABLE_FAN]
variable_fan_on = 0
gcode =
{% if printer["gcode_macro _ENABLE_FAN"].fan_on == 0 %}
SET_FAN_SPEED FAN=fan0 SPEED={printer.extruder.filament.part_cooling}
SET_FAN_SPEED FAN=fan2 SPEED={printer.extruder.filament.aux_cooling}
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=1
{% endif %}
[skew_correction]
[pid_profile extruder abs]
pid_version = 1
pid_target = 260.00
pid_tolerance = 0.0200
control = pid
pid_kp = 16.100
pid_ki = 1.058
pid_kd = 61.259
[pid_profile heater_bed abs]
pid_version = 1
pid_target = 105.00
pid_tolerance = 0.0200
control = pid
pid_kp = 51.427
pid_ki = 1.894
pid_kd = 349.061
[skew_correction skew]
xy_skew = 0.000
xz_skew = 0.000
yz_skew = 0.000
[pid_profile extruder pc]
pid_version = 1
pid_target = 250.00
pid_tolerance = 0.0200
control = pid
pid_kp = 17.627
pid_ki = 1.013
pid_kd = 76.678
[bed_mesh default]
version = 1
points =
-0.080000, 0.003125, 0.086875
-0.013438, 0.047187, 0.126875
0.057187, 0.112812, 0.140312
x_count = 3
y_count = 3
mesh_x_pps = 2
mesh_y_pps = 2
algo = lagrange
tension = 0.2
min_x = 161.25
max_x = 188.75
min_y = 161.25
max_y = 188.75
[cpap_heater]
pid_version = 1
pid_target = 40.00
pid_tolerance = 0.0200
control = pid
pid_kp = 8.528
pid_ki = 0.070
pid_kd = 260.544
=======================
DEBUG: registering extruder
DEBUG: registering extruder#: extruder
Extruder max_extrude_ratio=2.078758
mcu 'mcu': Starting serial connect
Loaded MCU 'mcu' 105 commands ( v0.10.0-557-gf7e29b27 / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-12+11) 2.31.1)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c3=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 CLOCK_FREQ=180000000 MCU=stm32f446xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
webhooks client 547573508624: New connection
TMC extruder failed to init: Unable to write tmc spi 'extruder' register GLOBALSCALER
Starting heater checks for extruder
Starting heater checks for heater_bed
bed_mesh: generated points
Index | Tool Adjusted | Probe
0 | (40.0, 40.0) | (40.0, 40.0)
1 | (85.0, 40.0) | (85.0, 40.0)
2 | (130.0, 40.0) | (130.0, 40.0)
3 | (175.0, 40.0) | (175.0, 40.0)
4 | (220.0, 40.0) | (220.0, 40.0)
5 | (265.0, 40.0) | (265.0, 40.0)
6 | (310.0, 40.0) | (310.0, 40.0)
7 | (310.0, 85.0) | (310.0, 85.0)
8 | (265.0, 85.0) | (265.0, 85.0)
9 | (220.0, 85.0) | (220.0, 85.0)
10 | (175.0, 85.0) | (175.0, 85.0)
11 | (130.0, 85.0) | (130.0, 85.0)
12 | (85.0, 85.0) | (85.0, 85.0)
13 | (40.0, 85.0) | (40.0, 85.0)
14 | (40.0, 130.0) | (40.0, 130.0)
15 | (85.0, 130.0) | (85.0, 130.0)
16 | (130.0, 130.0) | (130.0, 130.0)
17 | (175.0, 130.0) | (175.0, 130.0)
18 | (220.0, 130.0) | (220.0, 130.0)
19 | (265.0, 130.0) | (265.0, 130.0)
20 | (310.0, 130.0) | (310.0, 130.0)
21 | (310.0, 175.0) | (310.0, 175.0)
22 | (265.0, 175.0) | (265.0, 175.0)
23 | (220.0, 175.0) | (220.0, 175.0)
24 | (175.0, 175.0) | (175.0, 175.0)
25 | (130.0, 175.0) | (130.0, 175.0)
26 | (85.0, 175.0) | (85.0, 175.0)
27 | (40.0, 175.0) | (40.0, 175.0)
28 | (40.0, 220.0) | (40.0, 220.0)
29 | (85.0, 220.0) | (85.0, 220.0)
30 | (130.0, 220.0) | (130.0, 220.0)
31 | (175.0, 220.0) | (175.0, 220.0)
32 | (220.0, 220.0) | (220.0, 220.0)
33 | (265.0, 220.0) | (265.0, 220.0)
34 | (310.0, 220.0) | (310.0, 220.0)
35 | (310.0, 265.0) | (310.0, 265.0)
36 | (265.0, 265.0) | (265.0, 265.0)
37 | (220.0, 265.0) | (220.0, 265.0)
38 | (175.0, 265.0) | (175.0, 265.0)
39 | (130.0, 265.0) | (130.0, 265.0)
40 | (85.0, 265.0) | (85.0, 265.0)
41 | (40.0, 265.0) | (40.0, 265.0)
42 | (40.0, 310.0) | (40.0, 310.0)
43 | (85.0, 310.0) | (85.0, 310.0)
44 | (130.0, 310.0) | (130.0, 310.0)
45 | (175.0, 310.0) | (175.0, 310.0)
46 | (220.0, 310.0) | (220.0, 310.0)
47 | (265.0, 310.0) | (265.0, 310.0)
48 | (310.0, 310.0) | (310.0, 310.0)
Starting heater checks for chamber_heater
autotune_tmc set stepper_x pwm_freq=2
autotune_tmc stepper_x ncycles=219 pfdcycles=73
autotune_tmc set stepper_x tpfd=1
autotune_tmc set stepper_x tbl=1
autotune_tmc set stepper_x toff=1
autotune_tmc seting hysteresis based on 48.0 V
dcoilblank = 0.018462, dcoilsd = 0.003683
hysteresis = 1, htotal = 1, hstrt = 1, hend = 0
autotune_tmc set stepper_x hstrt=0
autotune_tmc set stepper_x hend=3
autotune_tmc using max PWM speed 595.876107
autotune_tmc set stepper_x pwm_autoscale=True
autotune_tmc set stepper_x pwm_autograd=True
webhooks client 547573508624: Client info {'program': 'Moonraker', 'version': 'v0.9.3-1-g4e00a07'}
autotune_tmc set stepper_x pwm_grad=3
autotune_tmc set stepper_x pwm_ofs=21
autotune_tmc set stepper_x pwm_reg=15
autotune_tmc set stepper_x pwm_lim=4
autotune_tmc set stepper_x tpwmthrs=1048575
autotune_tmc set stepper_x en_pwm_mode=False
autotune_tmc set stepper_x tcoolthrs=313(30.0)
autotune_tmc set stepper_x sgt=1
autotune_tmc set stepper_x small_hysteresis=False
autotune_tmc set stepper_x semin=2
autotune_tmc set stepper_x semax=4
autotune_tmc set stepper_x seup=3
autotune_tmc set stepper_x sedn=2
autotune_tmc set stepper_x seimin=1
autotune_tmc set stepper_x sfilt=0
autotune_tmc set stepper_x iholddelay=12
autotune_tmc set stepper_x vhighfs=False
autotune_tmc set stepper_x vhighchm=False
autotune_tmc set stepper_x multistep_filt=True
autotune_tmc set stepper_y pwm_freq=2
autotune_tmc stepper_y ncycles=219 pfdcycles=73
autotune_tmc set stepper_y tpfd=1
autotune_tmc set stepper_y tbl=1
autotune_tmc set stepper_y toff=1
autotune_tmc seting hysteresis based on 48.0 V
dcoilblank = 0.018462, dcoilsd = 0.003683
hysteresis = 1, htotal = 1, hstrt = 1, hend = 0
autotune_tmc set stepper_y hstrt=0
autotune_tmc set stepper_y hend=3
autotune_tmc using max PWM speed 595.876107
autotune_tmc set stepper_y pwm_autoscale=True
autotune_tmc set stepper_y pwm_autograd=True
autotune_tmc set stepper_y pwm_grad=3
autotune_tmc set stepper_y pwm_ofs=21
autotune_tmc set stepper_y pwm_reg=15
autotune_tmc set stepper_y pwm_lim=4
autotune_tmc set stepper_y tpwmthrs=1048575
autotune_tmc set stepper_y en_pwm_mode=False
autotune_tmc set stepper_y tcoolthrs=313(30.0)
autotune_tmc set stepper_y sgt=1
autotune_tmc set stepper_y small_hysteresis=False
autotune_tmc set stepper_y semin=2
autotune_tmc set stepper_y semax=4
autotune_tmc set stepper_y seup=3
autotune_tmc set stepper_y sedn=2
autotune_tmc set stepper_y seimin=1
autotune_tmc set stepper_y sfilt=0
autotune_tmc set stepper_y iholddelay=12
autotune_tmc set stepper_y vhighfs=False
autotune_tmc set stepper_y vhighchm=False
autotune_tmc set stepper_y multistep_filt=True
Stats 35.9: gcodein=0 mcu: mcu_awake=0.008 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4970 bytes_read=7759 bytes_retransmit=9 bytes_invalid=0 send_seq=418 receive_seq=418 retransmit_seq=2 srtt=0.003 rttvar=0.002 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180017431 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.1 pwm=0.000 sysload=3.05 cputime=5.814 memavail=3582620 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=71.2 pwm=0.000
Stats 36.9: gcodein=0 mcu: mcu_awake=0.008 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4992 bytes_read=7987 bytes_retransmit=9 bytes_invalid=0 send_seq=420 receive_seq=420 retransmit_seq=2 srtt=0.002 rttvar=0.002 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003713 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.05 cputime=5.853 memavail=3577364 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=71.1 pwm=0.000
Stats 37.9: gcodein=0 mcu: mcu_awake=0.008 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4998 bytes_read=8188 bytes_retransmit=9 bytes_invalid=0 send_seq=421 receive_seq=421 retransmit_seq=2 srtt=0.002 rttvar=0.002 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179997082 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.05 cputime=5.873 memavail=3569228 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=70.8 pwm=0.000
Stats 38.9: gcodein=0 mcu: mcu_awake=0.008 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5004 bytes_read=8382 bytes_retransmit=9 bytes_invalid=0 send_seq=422 receive_seq=422 retransmit_seq=2 srtt=0.002 rttvar=0.002 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004485 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=3.05 cputime=5.893 memavail=3569364 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=70.6 pwm=0.000
Stats 39.9: gcodein=0 mcu: mcu_awake=0.008 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5010 bytes_read=8604 bytes_retransmit=9 bytes_invalid=0 send_seq=423 receive_seq=423 retransmit_seq=2 srtt=0.002 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180008033 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.05 cputime=5.940 memavail=3564800 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=70.3 pwm=0.000
Stats 40.9: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=5016 bytes_read=8826 bytes_retransmit=9 bytes_invalid=0 send_seq=424 receive_seq=424 retransmit_seq=2 srtt=0.002 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180010309 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.12 cputime=5.966 memavail=3561052 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=69.7 pwm=0.000
Stats 41.9: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=5022 bytes_read=9034 bytes_retransmit=9 bytes_invalid=0 send_seq=425 receive_seq=425 retransmit_seq=2 srtt=0.002 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005002 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.12 cputime=5.987 memavail=3560684 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=69.6 pwm=0.000
Stats 42.9: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=5028 bytes_read=9257 bytes_retransmit=9 bytes_invalid=0 send_seq=426 receive_seq=426 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180001965 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=3.12 cputime=6.008 memavail=3577448 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=69.1 pwm=0.000
Stats 43.9: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=5034 bytes_read=9464 bytes_retransmit=9 bytes_invalid=0 send_seq=427 receive_seq=427 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179998821 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.12 cputime=6.049 memavail=3571080 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=68.8 pwm=0.000
Stats 44.9: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000012 mcu_task_stddev=0.000013 bytes_write=5040 bytes_read=9672 bytes_retransmit=9 bytes_invalid=0 send_seq=428 receive_seq=428 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180000508 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=3.12 cputime=6.079 memavail=3576148 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=68.4 pwm=0.000
Stats 45.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5046 bytes_read=9909 bytes_retransmit=9 bytes_invalid=0 send_seq=429 receive_seq=429 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=179999110 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=3.03 cputime=6.109 memavail=3599652 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=68.3 pwm=0.000
Stats 46.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5052 bytes_read=10116 bytes_retransmit=9 bytes_invalid=0 send_seq=430 receive_seq=430 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180000466 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.03 cputime=6.138 memavail=3596560 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.8 pwm=0.000
Stats 47.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5058 bytes_read=10324 bytes_retransmit=9 bytes_invalid=0 send_seq=431 receive_seq=431 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180000972 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.03 cputime=6.165 memavail=3598844 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.5 pwm=0.000
Stats 48.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5064 bytes_read=10547 bytes_retransmit=9 bytes_invalid=0 send_seq=432 receive_seq=432 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180001671 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.03 cputime=6.195 memavail=3598352 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=67.3 pwm=0.000
Heater extruder approaching new target of 200.000
Stats 49.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5086 bytes_read=10759 bytes_retransmit=9 bytes_invalid=0 send_seq=434 receive_seq=434 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180001619 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=3.03 cputime=6.230 memavail=3592648 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=67.0 pwm=1.000
Stats 50.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5092 bytes_read=10981 bytes_retransmit=9 bytes_invalid=0 send_seq=435 receive_seq=435 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002803 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.95 cputime=6.261 memavail=3591444 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=66.7 pwm=1.000
Stats 51.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5098 bytes_read=11204 bytes_retransmit=9 bytes_invalid=0 send_seq=436 receive_seq=436 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002036 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.95 cputime=6.290 memavail=3577176 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=66.8 pwm=1.000
Stats 52.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5104 bytes_read=11411 bytes_retransmit=9 bytes_invalid=0 send_seq=437 receive_seq=437 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002397 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.95 cputime=6.320 memavail=3567856 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=67.8 pwm=1.000
Stats 53.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5126 bytes_read=11624 bytes_retransmit=9 bytes_invalid=0 send_seq=439 receive_seq=439 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002182 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.95 cputime=6.348 memavail=3574756 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=69.2 pwm=1.000
Stats 54.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5132 bytes_read=11847 bytes_retransmit=9 bytes_invalid=0 send_seq=440 receive_seq=440 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002784 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.95 cputime=6.377 memavail=3574872 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=70.9 pwm=1.000
Stats 55.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5138 bytes_read=12068 bytes_retransmit=9 bytes_invalid=0 send_seq=441 receive_seq=441 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003263 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.87 cputime=6.406 memavail=3574824 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=73.9 pwm=1.000
Stats 56.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5144 bytes_read=12276 bytes_retransmit=9 bytes_invalid=0 send_seq=442 receive_seq=442 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002687 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.87 cputime=6.435 memavail=3574824 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=76.7 pwm=1.000
Stats 57.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5166 bytes_read=12504 bytes_retransmit=9 bytes_invalid=0 send_seq=444 receive_seq=444 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003055 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.87 cputime=6.467 memavail=3574860 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=79.6 pwm=1.000
Stats 58.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5172 bytes_read=12711 bytes_retransmit=9 bytes_invalid=0 send_seq=445 receive_seq=445 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003102 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.87 cputime=6.497 memavail=3574828 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=83.7 pwm=1.000
Stats 59.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5178 bytes_read=12919 bytes_retransmit=9 bytes_invalid=0 send_seq=446 receive_seq=446 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002583 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.87 cputime=6.524 memavail=3574828 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=87.2 pwm=1.000
Stats 60.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5184 bytes_read=13156 bytes_retransmit=9 bytes_invalid=0 send_seq=447 receive_seq=447 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002194 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.80 cputime=6.552 memavail=3574860 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=90.8 pwm=1.000
Stats 61.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5206 bytes_read=13359 bytes_retransmit=9 bytes_invalid=0 send_seq=449 receive_seq=449 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002895 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.80 cputime=6.582 memavail=3574700 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=95.8 pwm=1.000
Stats 62.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5212 bytes_read=13554 bytes_retransmit=9 bytes_invalid=0 send_seq=450 receive_seq=450 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002712 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.80 cputime=6.611 memavail=3574864 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=99.6 pwm=1.000
Stats 63.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5218 bytes_read=13777 bytes_retransmit=9 bytes_invalid=0 send_seq=451 receive_seq=451 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002633 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.80 cputime=6.641 memavail=3574832 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=103.3 pwm=1.000
Stats 64.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5224 bytes_read=13984 bytes_retransmit=9 bytes_invalid=0 send_seq=452 receive_seq=452 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002854 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.80 cputime=6.670 memavail=3617216 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=108.4 pwm=1.000
Stats 65.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5230 bytes_read=14206 bytes_retransmit=9 bytes_invalid=0 send_seq=453 receive_seq=453 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003046 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.74 cputime=6.703 memavail=3617436 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=112.2 pwm=1.000
Stats 66.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5252 bytes_read=14434 bytes_retransmit=9 bytes_invalid=0 send_seq=455 receive_seq=455 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003467 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.74 cputime=6.729 memavail=3617484 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=116.1 pwm=1.000
Stats 67.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5258 bytes_read=14641 bytes_retransmit=9 bytes_invalid=0 send_seq=456 receive_seq=456 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003496 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.74 cputime=6.760 memavail=3617452 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=121.1 pwm=1.000
Stats 68.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5264 bytes_read=14864 bytes_retransmit=9 bytes_invalid=0 send_seq=457 receive_seq=457 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003716 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.74 cputime=6.786 memavail=3617452 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=124.8 pwm=1.000
Stats 69.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5270 bytes_read=15072 bytes_retransmit=9 bytes_invalid=0 send_seq=458 receive_seq=458 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004051 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.74 cputime=6.828 memavail=3617420 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=128.7 pwm=1.000
Stats 70.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5292 bytes_read=15298 bytes_retransmit=9 bytes_invalid=0 send_seq=460 receive_seq=460 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003738 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.68 cputime=6.857 memavail=3617416 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=133.5 pwm=1.000
Stats 71.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5298 bytes_read=15521 bytes_retransmit=9 bytes_invalid=0 send_seq=461 receive_seq=461 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003519 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.68 cputime=6.883 memavail=3617356 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=137.1 pwm=1.000
Stats 73.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5304 bytes_read=15729 bytes_retransmit=9 bytes_invalid=0 send_seq=462 receive_seq=462 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003598 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.68 cputime=6.917 memavail=3617356 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=140.9 pwm=1.000
Stats 74.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5310 bytes_read=15936 bytes_retransmit=9 bytes_invalid=0 send_seq=463 receive_seq=463 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003326 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.68 cputime=6.943 memavail=3617300 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=145.6 pwm=1.000
Stats 75.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5332 bytes_read=16164 bytes_retransmit=9 bytes_invalid=0 send_seq=465 receive_seq=465 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003119 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.68 cputime=6.976 memavail=3617396 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=149.3 pwm=1.000
Stats 76.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5338 bytes_read=16386 bytes_retransmit=9 bytes_invalid=0 send_seq=466 receive_seq=466 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003046 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.54 cputime=7.001 memavail=3617424 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=152.7 pwm=1.000
Stats 77.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5344 bytes_read=16593 bytes_retransmit=9 bytes_invalid=0 send_seq=467 receive_seq=467 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002936 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.54 cputime=7.041 memavail=3617580 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=157.2 pwm=1.000
Stats 78.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5366 bytes_read=16821 bytes_retransmit=9 bytes_invalid=0 send_seq=469 receive_seq=469 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002915 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.54 cputime=7.082 memavail=3617548 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=160.8 pwm=0.835
Stats 79.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5420 bytes_read=17044 bytes_retransmit=9 bytes_invalid=0 send_seq=473 receive_seq=473 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002837 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.54 cputime=7.110 memavail=3617584 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=163.9 pwm=0.538
Stats 80.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5485 bytes_read=17266 bytes_retransmit=9 bytes_invalid=0 send_seq=477 receive_seq=477 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002952 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.54 cputime=7.157 memavail=3617616 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=168.7 pwm=0.267
Stats 81.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5507 bytes_read=17508 bytes_retransmit=9 bytes_invalid=0 send_seq=479 receive_seq=479 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002953 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.42 cputime=7.187 memavail=3617584 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=171.6 pwm=0.193
Stats 82.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5529 bytes_read=17721 bytes_retransmit=9 bytes_invalid=0 send_seq=481 receive_seq=481 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002842 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.42 cputime=7.213 memavail=3617644 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=174.7 pwm=0.133
Stats 83.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5556 bytes_read=17949 bytes_retransmit=9 bytes_invalid=0 send_seq=484 receive_seq=484 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003237 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.42 cputime=7.246 memavail=3617580 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=178.3 pwm=0.077
Stats 84.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5562 bytes_read=18172 bytes_retransmit=9 bytes_invalid=0 send_seq=485 receive_seq=485 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003186 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.42 cputime=7.272 memavail=3617684 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=180.4 pwm=0.077
Heater extruder within range of 200.000
Stats 85.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5568 bytes_read=18380 bytes_retransmit=9 bytes_invalid=0 send_seq=486 receive_seq=486 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003059 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.42 cputime=7.307 memavail=3617656 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=182.2 pwm=0.077
Stats 86.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5585 bytes_read=18590 bytes_retransmit=9 bytes_invalid=0 send_seq=487 receive_seq=487 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002998 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.31 cputime=7.334 memavail=3617688 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=184.3 pwm=0.132
Stats 87.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5607 bytes_read=18806 bytes_retransmit=9 bytes_invalid=0 send_seq=489 receive_seq=489 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002930 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.31 cputime=7.368 memavail=3617560 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=185.1 pwm=0.207
Stats 88.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5613 bytes_read=19014 bytes_retransmit=9 bytes_invalid=0 send_seq=490 receive_seq=490 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180002996 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.31 cputime=7.392 memavail=3617592 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=186.1 pwm=0.207
Stats 89.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5651 bytes_read=19231 bytes_retransmit=9 bytes_invalid=0 send_seq=493 receive_seq=493 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003212 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.31 cputime=7.426 memavail=3617656 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=186.7 pwm=0.316
Stats 90.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5673 bytes_read=19459 bytes_retransmit=9 bytes_invalid=0 send_seq=495 receive_seq=495 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003373 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.31 cputime=7.456 memavail=3617624 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=186.9 pwm=0.367
Stats 91.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5679 bytes_read=19681 bytes_retransmit=9 bytes_invalid=0 send_seq=496 receive_seq=496 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003510 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=7.482 memavail=3617592 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=187.2 pwm=0.367
Stats 92.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5685 bytes_read=19888 bytes_retransmit=9 bytes_invalid=0 send_seq=497 receive_seq=497 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003668 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=7.514 memavail=3617560 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=187.7 pwm=0.367
Stats 93.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5707 bytes_read=20116 bytes_retransmit=9 bytes_invalid=0 send_seq=499 receive_seq=499 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003722 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.8 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=7.539 memavail=3617624 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=188.0 pwm=0.419
Stats 94.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5713 bytes_read=20324 bytes_retransmit=9 bytes_invalid=0 send_seq=500 receive_seq=500 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003820 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=7.573 memavail=3617624 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=188.2 pwm=0.419
Stats 95.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5719 bytes_read=20531 bytes_retransmit=9 bytes_invalid=0 send_seq=501 receive_seq=501 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003803 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=7.601 memavail=3617572 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=189.0 pwm=0.419
Stats 96.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5725 bytes_read=20768 bytes_retransmit=9 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003952 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.34 cputime=7.640 memavail=3617572 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=189.3 pwm=0.419
Stats 97.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5747 bytes_read=20981 bytes_retransmit=9 bytes_invalid=0 send_seq=504 receive_seq=504 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003850 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.34 cputime=7.667 memavail=3617636 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=190.1 pwm=0.360
Stats 98.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5753 bytes_read=21188 bytes_retransmit=9 bytes_invalid=0 send_seq=505 receive_seq=505 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003902 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.34 cputime=7.700 memavail=3617604 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=191.1 pwm=0.360
Stats 99.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5759 bytes_read=21411 bytes_retransmit=9 bytes_invalid=0 send_seq=506 receive_seq=506 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180003931 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.34 cputime=7.729 memavail=3617480 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=191.5 pwm=0.360
Stats 100.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5781 bytes_read=21624 bytes_retransmit=9 bytes_invalid=0 send_seq=508 receive_seq=508 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004011 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.34 cputime=7.756 memavail=3617584 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=192.2 pwm=0.304
Stats 101.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5787 bytes_read=21845 bytes_retransmit=9 bytes_invalid=0 send_seq=509 receive_seq=509 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004161 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.23 cputime=7.788 memavail=3617520 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=193.3 pwm=0.304
Stats 102.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5809 bytes_read=22073 bytes_retransmit=9 bytes_invalid=0 send_seq=511 receive_seq=511 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004207 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.23 cputime=7.813 memavail=3617488 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=194.1 pwm=0.248
Stats 103.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5815 bytes_read=22281 bytes_retransmit=9 bytes_invalid=0 send_seq=512 receive_seq=512 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004377 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.23 cputime=7.842 memavail=3617456 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=194.9 pwm=0.248
Stats 104.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5821 bytes_read=22488 bytes_retransmit=9 bytes_invalid=0 send_seq=513 receive_seq=513 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004340 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.23 cputime=7.869 memavail=3617428 print_time=59.097 buffer_time=0.000 print_stall=0 extruder: target=200 temp=195.6 pwm=0.248
Transition to shutdown state: Unable to write tmc spi 'extruder' register GLOBALSCALER
Dumping gcode input 0 blocks
Dumping 20 requests for client 547573508624
Received 36.222909: b'{"id": 547951518688, "method": "register_remote_method", "params": {"response_template": {"method": "pause_job_queue"}, "remote_method": "pause_job_queue"}}'
Received 36.235834: b'{"id": 547951125856, "method": "register_remote_method", "params": {"response_template": {"method": "start_job_queue"}, "remote_method": "start_job_queue"}}'
Received 36.262523: b'{"id": 547951635824, "method": "objects/query", "params": {"objects": {"heaters": null}}}'
Received 36.270790: b'{"id": 547951634336, "method": "objects/query", "params": {"objects": {"heaters": null}}}'
Received 36.442402: b'{"id": 547951637072, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "z_thermal_adjust": null, "heater_generic chamber_heater": null, "extruder": null}, "response_template": {"method": "process_status_update"}}}'
Received 36.691388: b'{"id": 547951126912, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "z_thermal_adjust": null, "heater_generic chamber_heater": null, "extruder": null}, "response_template": {"method": "process_status_update"}}}'
Received 37.769687: b'{"id": 547951637168, "method": "objects/subscribe", "params": {"objects": {"print_stats": null, "webhooks": null, "virtual_sdcard": null, "history": null, "heater_bed": null, "z_thermal_adjust": null, "heater_generic chamber_heater": null, "extruder": null}, "response_template": {"method": "process_status_update"}}}'
Received 37.949699: b'{"id": 547951637792, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 39.316553: b'{"id": 547951640000, "method": "info", "params": {}}'
Received 39.336218: b'{"id": 547951637264, "method": "objects/query", "params": {"objects": {"configfile": null}}}'
Received 39.499086: b'{"id": 547951639376, "method": "gcode/help", "params": {}}'
Received 39.544251: b'{"id": 547951639376, "method": "objects/query", "params": {"objects": {"bed_mesh": null, "configfile": null, "display_status": null, "extruder": null, "fan": null, "gcode_move": null, "heater_bed": null, "idle_timeout": null, "pause_resume": null, "print_stats": null, "toolhead": null, "virtual_sdcard": null, "webhooks": null, "motion_report": null, "firmware_retraction": null, "exclude_object": null, "manual_probe": null, "heater_generic chamber_heater": null, "fan_generic fan0": null, "fan_generic fan2": null, "heater_fan hotend_fan": null, "heater_fan chamber_heater_fan": null, "led led_strip": null}}}'
Received 39.740737: b'{"id": 547951638848, "method": "objects/subscribe", "params": {"objects": {"bed_mesh": ["profile_name", "mesh_max", "mesh_min", "probed_matrix", "profiles"], "configfile": ["config", "warnings"], "display_status": ["progress", "message"], "fan": ["speed"], "gcode_move": ["extrude_factor", "gcode_position", "homing_origin", "speed_factor", "speed"], "idle_timeout": ["state"], "pause_resume": ["is_paused"], "print_stats": null, "toolhead": ["homed_axes", "estimated_print_time", "print_time", "position", "extruder", "max_accel", "minimum_cruise_ratio", "max_velocity", "square_corner_velocity"], "virtual_sdcard": null, "webhooks": null, "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "motion_report": ["live_position", "live_velocity", "live_extruder_velocity"], "exclude_object": ["current_object", "objects", "excluded_objects"], "manual_probe": ["is_active"], "screws_tilt_adjust": ["results", "error"], "extruder": null, "heater_bed": null, "heater_generic chamber_heater": null, "fan_generic fan0": ["speed"], "fan_generic fan2": ["speed"], "heater_fan hotend_fan": ["speed"], "heater_fan chamber_heater_fan": ["speed"], "led led_strip": ["color_data"], "z_thermal_adjust": null, "history": null}, "response_template": {"method": "process_status_update"}}}'
Received 43.450488: b'{"id": 547950138688, "method": "objects/query", "params": {"objects": {"gcode": ["commands"]}}}'
Received 43.451525: b'{"id": 547950139120, "method": "info", "params": {}}'
Received 43.451525: b'{"id": 547950138304, "method": "objects/list", "params": {}}'
Received 43.468876: b'{"id": 547950139936, "method": "objects/subscribe", "params": {"objects": {"gcode": null, "webhooks": null, "configfile": null, "mcu": null, "gcode_macro CHOPPER_TUNE": null, "gcode_macro _detect_driver": null, "gcode_macro _chop_apply_regs": null, "gcode_macro _chop_workflow": null, "gcode_move": null, "print_stats": null, "virtual_sdcard": null, "pause_resume": null, "display_status": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro SET_PAUSE_NEXT_LAYER": null, "gcode_macro SET_PAUSE_AT_LAYER": null, "gcode_macro SET_PRINT_STATS_INFO": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "gcode_macro _CLIENT_EXTRUDE": null, "gcode_macro _CLIENT_RETRACT": null, "gcode_macro BED_MESH_CALIBRATE": null, "gcode_macro LINE_PURGE": null, "gcode_macro SMART_PARK": null, "gcode_macro _KAMP_Settings": null, "gcode_macro _TAP_VARIABLES": null, "gcode_macro _PRE_PROBE_CHECK": null, "gcode_macro _PROBE_TEMP_CHECK": null, "gcode_macro _POST_PROBING": null, "gcode_macro _POST_PROBE": null, "gcode_macro SET_PROBE_TEMP": null, "gcode_macro Z_TILT_ADJUST": null, "gcode_macro _TAP_SETTINGS": null, "heaters": null, "stepper_enable": null, "tmc5160 stepper_y": null, "tmc5160 stepper_x": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 stepper_z2": null, "tmc5160 extruder": null, "heater_bed": null, "probe": null, "heater_fan hotend_fan": null, "fan_generic fan0": null, "idle_timeout": null, "bed_mesh": null, "z_tilt": null, "gcode_macro G32": null, "save_variables": null, "gcode_macro _PREHEAT": null, "gcode_macro _COOLOFF": null, "gcode_macro PRINT_START": null, "gcode_macro PRINT_END": null, "exclude_object": null, "filaments": null, "z_thermal_adjust": null, "led led_strip": null, "heater_generic chamber_heater": null, "heater_fan chamber_heater_fan": null, "fan_generic fan2": null, "gcode_macro M106": null, "gcode_macro _ENABLE_FAN": null, "motion_report": null, "query_endstops": null, "system_stats": null, "manual_probe": null, "toolhead": null, "extruder": null, "history": null, "fan": ["speed"], "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "screws_tilt_adjust": ["results", "error"]}, "response_template": {"method": "process_status_update"}}}'
Received 44.131452: b'{"id": 547951639376, "method": "objects/query", "params": {"objects": {"extruder": ["can_extrude"]}}}'
Received 49.264701: b'{"id": 547951631984, "method": "gcode/script", "params": {"script": "SET_HEATER_TEMPERATURE HEATER=extruder TARGET=200"}}'
Received 103.889294: b'{"id": 547951631888, "method": "gcode/script", "params": {"script": "SAVE_GCODE_STATE NAME=_ui_extrude\\nM83\\nG1 E25 F300\\nRESTORE_GCODE_STATE NAME=_ui_extrude"}}'
gcode state: absolute_coord=True absolute_extrude=True base_position=[0.0, 0.0, 0.0, 25.0] last_position=[0.0, 0.0, 0.0, 25.0] homing_position=[0.0, 0.0, 0.0, 0.0] speed_factor=0.016666666666666666 extrude_factor=1.0 speed=25.0
Reactor garbage collection: (37.950429943, 0.0, 0.0)
MCU 'mcu' shutdown: Command request
clocksync state: mcu_freq=180000000 last_clock=20378166955 clock_est=(77.697 15710153603 180004340.137) min_half_rtt=0.000113 min_rtt_time=43.556 time_avg=77.697(470.036) clock_avg=15710153603.963(84608542236.183) pred_variance=4836396297.468
Dumping serial stats: bytes_write=6052 bytes_read=22625 bytes_retransmit=9 bytes_invalid=0 send_seq=523 receive_seq=523 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0
Dumping send queue 100 messages
Sent 0 40.602372 40.602372 6: seq: 17, get_clock
Sent 1 41.587031 41.587031 6: seq: 18, get_clock
Sent 2 42.572066 42.572066 6: seq: 19, get_clock
Sent 3 43.556339 43.556339 6: seq: 1a, get_clock
Sent 4 44.540661 44.540661 6: seq: 1b, get_clock
Sent 5 45.525233 45.525233 6: seq: 1c, get_clock
Sent 6 46.509676 46.509676 6: seq: 1d, get_clock
Sent 7 47.493814 47.493814 6: seq: 1e, get_clock
Sent 8 48.478715 48.478715 6: seq: 1f, get_clock
Sent 9 49.331402 49.331402 16: seq: 10, queue_digital_out oid=36 clock=2058505408 on_ticks=18000000
Sent 10 49.463932 49.463932 6: seq: 11, get_clock
Sent 11 50.448442 50.448442 6: seq: 12, get_clock
Sent 12 51.433194 51.433194 6: seq: 13, get_clock
Sent 13 52.417741 52.417741 6: seq: 14, get_clock
Sent 14 53.403018 53.403018 6: seq: 15, get_clock
Sent 15 53.531180 53.531180 16: seq: 16, queue_digital_out oid=36 clock=2814505408 on_ticks=18000000
Sent 16 54.387579 54.387579 6: seq: 17, get_clock
Sent 17 55.372579 55.372579 6: seq: 18, get_clock
Sent 18 56.357233 56.357233 6: seq: 19, get_clock
Sent 19 57.341641 57.341641 6: seq: 1a, get_clock
Sent 20 57.730709 57.730709 16: seq: 1b, queue_digital_out oid=36 clock=3570505407 on_ticks=18000000
Sent 21 58.325840 58.325840 6: seq: 1c, get_clock
Sent 22 59.310322 59.310322 6: seq: 1d, get_clock
Sent 23 60.295292 60.295292 6: seq: 1e, get_clock
Sent 24 61.280357 61.280357 6: seq: 1f, get_clock
Sent 25 61.930853 61.930853 16: seq: 10, queue_digital_out oid=36 clock=31538112 on_ticks=18000000
Sent 26 62.265109 62.265109 6: seq: 11, get_clock
Sent 27 63.250045 63.250045 6: seq: 12, get_clock
Sent 28 64.234742 64.234742 6: seq: 13, get_clock
Sent 29 65.219742 65.219742 6: seq: 14, get_clock
Sent 30 66.130564 66.130564 16: seq: 15, queue_digital_out oid=36 clock=787538112 on_ticks=18000000
Sent 31 66.204440 66.204440 6: seq: 16, get_clock
Sent 32 67.188848 67.188848 6: seq: 17, get_clock
Sent 33 68.173601 68.173601 6: seq: 18, get_clock
Sent 34 69.158404 69.158404 6: seq: 19, get_clock
Sent 35 70.143243 70.143243 6: seq: 1a, get_clock
Sent 36 70.330050 70.330050 16: seq: 1b, queue_digital_out oid=36 clock=1543538111 on_ticks=18000000
Sent 37 71.128176 71.128176 6: seq: 1c, get_clock
Sent 38 72.112779 72.112779 6: seq: 1d, get_clock
Sent 39 73.097345 73.097345 6: seq: 1e, get_clock
Sent 40 74.082275 74.082275 6: seq: 1f, get_clock
Sent 41 74.530159 74.530159 16: seq: 10, queue_digital_out oid=36 clock=2299538111 on_ticks=18000000
Sent 42 75.067104 75.067104 6: seq: 11, get_clock
Sent 43 76.052193 76.052193 6: seq: 12, get_clock
Sent 44 77.037069 77.037069 6: seq: 13, get_clock
Sent 45 77.829914 77.829914 16: seq: 14, queue_digital_out oid=36 clock=2893538111 on_ticks=15029902
Sent 46 78.021184 78.021184 6: seq: 15, get_clock
Sent 47 78.130104 78.130104 16: seq: 16, queue_digital_out oid=36 clock=2947538112 on_ticks=12906325
Sent 48 78.430053 78.430053 16: seq: 17, queue_digital_out oid=36 clock=3001538112 on_ticks=11206308
Sent 49 78.729665 78.729665 16: seq: 18, queue_digital_out oid=36 clock=3055538111 on_ticks=9682725
Sent 50 79.005861 79.005861 17: seq: 19, get_clock, queue_digital_out oid=36 clock=3109538111 on_ticks=8395429
Sent 51 79.330001 79.330001 16: seq: 1a, queue_digital_out oid=36 clock=3163538111 on_ticks=7095958
Sent 52 79.630284 79.630284 16: seq: 1b, queue_digital_out oid=36 clock=3217538112 on_ticks=5921486
Sent 53 79.930143 79.930143 16: seq: 1c, queue_digital_out oid=36 clock=3271538112 on_ticks=4800152
Sent 54 79.993050 79.993050 6: seq: 1d, get_clock
Sent 55 80.529635 80.529635 16: seq: 1e, queue_digital_out oid=36 clock=3379538111 on_ticks=3478262
Sent 56 80.977280 80.977280 6: seq: 1f, get_clock
Sent 57 81.129652 81.129652 16: seq: 10, queue_digital_out oid=36 clock=3487538112 on_ticks=2394836
Sent 58 81.961792 81.961792 6: seq: 11, get_clock
Sent 59 82.329653 82.329653 15: seq: 12, queue_digital_out oid=36 clock=3703538111 on_ticks=1391490
Sent 60 82.946554 82.946554 6: seq: 13, get_clock
Sent 61 83.931133 83.931133 6: seq: 14, get_clock
Sent 62 84.916324 84.916324 6: seq: 15, get_clock
Sent 63 85.901219 85.901219 17: seq: 16, get_clock, queue_digital_out oid=36 clock=56570816 on_ticks=2369890
Sent 64 86.829915 86.829915 16: seq: 17, queue_digital_out oid=36 clock=218570815 on_ticks=3730050
Sent 65 86.886251 86.886251 6: seq: 18, get_clock
Sent 66 87.870963 87.870963 6: seq: 19, get_clock
Sent 67 88.029916 88.029916 16: seq: 1a, queue_digital_out oid=36 clock=434570816 on_ticks=4694973
Sent 68 88.856600 88.856600 6: seq: 1b, get_clock
Sent 69 88.929231 88.929231 16: seq: 1c, queue_digital_out oid=36 clock=596570816 on_ticks=5685700
Sent 70 89.829573 89.829573 16: seq: 1d, queue_digital_out oid=36 clock=758570815 on_ticks=6597604
Sent 71 89.841683 89.841683 6: seq: 1e, get_clock
Sent 72 90.826704 90.826704 6: seq: 1f, get_clock
Sent 73 91.811620 91.811620 6: seq: 10, get_clock
Sent 74 92.529589 92.529589 16: seq: 11, queue_digital_out oid=36 clock=1244570816 on_ticks=7548725
Sent 75 92.796848 92.796848 6: seq: 12, get_clock
Sent 76 93.781724 93.781724 6: seq: 13, get_clock
Sent 77 94.766004 94.766004 6: seq: 14, get_clock
Sent 78 95.751563 95.751563 6: seq: 15, get_clock
Sent 79 96.728640 96.728640 16: seq: 16, queue_digital_out oid=36 clock=2000570816 on_ticks=6478031
Sent 80 96.736212 96.736212 6: seq: 17, get_clock
Sent 81 97.720816 97.720816 6: seq: 18, get_clock
Sent 82 98.705869 98.705869 6: seq: 19, get_clock
Sent 83 99.128606 99.128606 16: seq: 1a, queue_digital_out oid=36 clock=2432570816 on_ticks=5463545
Sent 84 99.690719 99.690719 6: seq: 1b, get_clock
Sent 85 100.675493 100.675493 6: seq: 1c, get_clock
Sent 86 101.528751 101.528751 16: seq: 1d, queue_digital_out oid=36 clock=2864570816 on_ticks=4457628
Sent 87 101.660760 101.660760 6: seq: 1e, get_clock
Sent 88 102.645376 102.645376 6: seq: 1f, get_clock
Sent 89 103.629956 103.629956 6: seq: 10, get_clock
Sent 90 103.992149 103.992149 33: seq: 11, set_next_step_dir oid=17 dir=0, queue_digital_out oid=37 clock=3308301272 on_ticks=0, queue_step oid=17 interval=3308363891 count=1 add=0, queue_step oid=17 interval=52166 count=1654 add=0
Sent 91 103.995856 103.995856 61: seq: 12, queue_step oid=17 interval=52167 count=1725 add=0, queue_step oid=17 interval=52166 count=1726 add=0, queue_step oid=17 interval=52166 count=1725 add=0, queue_step oid=17 interval=52166 count=1725 add=0, queue_step oid=17 interval=52167 count=1725 add=0, queue_step oid=17 interval=52166 count=1726 add=0, queue_step oid=17 interval=52166 count=1725 add=0
Sent 92 103.997032 103.997032 37: seq: 13, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00', queue_step oid=17 interval=52166 count=1725 add=0, queue_step oid=17 interval=52167 count=1725 add=0
Sent 93 103.999651 103.999651 21: seq: 14, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 94 104.002327 104.002327 21: seq: 15, spi_send oid=5 data=b'\x8b\x00\x00\x00 ', spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 95 104.004191 104.004191 13: seq: 16, spi_send oid=5 data=b'\x8b\x00\x00\x00 '
Sent 96 104.004289 104.004289 13: seq: 17, spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 97 104.005228 104.005228 13: seq: 18, spi_send oid=5 data=b'\x8b\x00\x00\x00 '
Sent 98 104.005312 104.005312 13: seq: 19, spi_transfer oid=5 data=b'\x00\x00\x00\x00\x00'
Sent 99 104.009186 104.009186 6: seq: 1a, emergency_stop
Dumping receive queue 100 messages
Receive: 0 97.576617 96.736212 14: seq: 18, analog_in_state oid=35 next_clock=2161130816 value=8793
Receive: 1 97.706619 96.736212 15: seq: 18, analog_in_state oid=18 next_clock=2184530816 value=31461
Receive: 2 97.721636 97.720816 11: seq: 19, clock clock=2134651941
Receive: 3 97.746623 97.720816 15: seq: 19, analog_in_state oid=22 next_clock=2191730816 value=23231
Receive: 4 97.786612 97.720816 15: seq: 19, analog_in_state oid=26 next_clock=2198930816 value=31464
Receive: 5 97.876934 97.720816 14: seq: 19, analog_in_state oid=35 next_clock=2215130816 value=8798
Receive: 6 98.006914 97.720816 15: seq: 19, analog_in_state oid=18 next_clock=2238530816 value=31465
Receive: 7 98.046611 97.720816 15: seq: 19, analog_in_state oid=22 next_clock=2245730816 value=23224
Receive: 8 98.086588 97.720816 15: seq: 19, analog_in_state oid=26 next_clock=2252930816 value=31464
Receive: 9 98.176613 97.720816 14: seq: 19, analog_in_state oid=35 next_clock=2269130816 value=8799
Receive: 10 98.306574 97.720816 15: seq: 19, analog_in_state oid=18 next_clock=2292530816 value=31462
Receive: 11 98.346649 97.720816 15: seq: 19, analog_in_state oid=22 next_clock=2299730816 value=23229
Receive: 12 98.386702 97.720816 15: seq: 19, analog_in_state oid=26 next_clock=2306930816 value=31467
Receive: 13 98.476596 97.720816 14: seq: 19, analog_in_state oid=35 next_clock=2323130816 value=8801
Receive: 14 98.606651 97.720816 15: seq: 19, analog_in_state oid=18 next_clock=2346530816 value=31464
Receive: 15 98.646722 97.720816 15: seq: 19, analog_in_state oid=22 next_clock=2353730816 value=23229
Receive: 16 98.686622 97.720816 15: seq: 19, analog_in_state oid=26 next_clock=2360930816 value=31467
Receive: 17 98.706606 98.705869 11: seq: 1a, clock clock=2311956486
Receive: 18 98.776629 98.705869 14: seq: 1a, analog_in_state oid=35 next_clock=2377130816 value=8804
Receive: 19 98.906598 98.705869 15: seq: 1a, analog_in_state oid=18 next_clock=2400530816 value=31463
Receive: 20 98.946593 98.705869 15: seq: 1a, analog_in_state oid=22 next_clock=2407730816 value=23228
Receive: 21 98.986720 98.705869 15: seq: 1a, analog_in_state oid=26 next_clock=2414930816 value=31466
Receive: 22 99.076611 98.705869 14: seq: 1a, analog_in_state oid=35 next_clock=2431130816 value=8810
Receive: 23 99.206554 99.128606 15: seq: 1b, analog_in_state oid=18 next_clock=2454530816 value=31460
Receive: 24 99.246625 99.128606 15: seq: 1b, analog_in_state oid=22 next_clock=2461730816 value=23231
Receive: 25 99.286658 99.128606 15: seq: 1b, analog_in_state oid=26 next_clock=2468930816 value=31463
Receive: 26 99.376535 99.128606 14: seq: 1b, analog_in_state oid=35 next_clock=2485130816 value=8812
Receive: 27 99.507094 99.128606 15: seq: 1b, analog_in_state oid=18 next_clock=2508530816 value=31460
Receive: 28 99.546560 99.128606 15: seq: 1b, analog_in_state oid=22 next_clock=2515730816 value=23229
Receive: 29 99.586561 99.128606 15: seq: 1b, analog_in_state oid=26 next_clock=2522930816 value=31465
Receive: 30 99.676584 99.128606 14: seq: 1b, analog_in_state oid=35 next_clock=2539130816 value=8814
Receive: 31 99.691610 99.690719 11: seq: 1c, clock clock=2489260466
Receive: 32 99.806618 99.690719 15: seq: 1c, analog_in_state oid=18 next_clock=2562530816 value=31462
Receive: 33 99.846591 99.690719 15: seq: 1c, analog_in_state oid=22 next_clock=2569730816 value=23228
Receive: 34 99.886621 99.690719 15: seq: 1c, analog_in_state oid=26 next_clock=2576930816 value=31465
Receive: 35 99.976610 99.690719 14: seq: 1c, analog_in_state oid=35 next_clock=2593130816 value=8819
Receive: 36 100.106937 99.690719 15: seq: 1c, analog_in_state oid=18 next_clock=2616530816 value=31462
Receive: 37 100.146838 99.690719 15: seq: 1c, analog_in_state oid=22 next_clock=2623730816 value=23224
Receive: 38 100.186902 99.690719 15: seq: 1c, analog_in_state oid=26 next_clock=2630930816 value=31464
Receive: 39 100.276613 99.690719 14: seq: 1c, analog_in_state oid=35 next_clock=2647130816 value=8823
Receive: 40 100.406618 99.690719 15: seq: 1c, analog_in_state oid=18 next_clock=2670530816 value=31461
Receive: 41 100.446591 99.690719 15: seq: 1c, analog_in_state oid=22 next_clock=2677730816 value=23224
Receive: 42 100.486622 99.690719 15: seq: 1c, analog_in_state oid=26 next_clock=2684930816 value=31464
Receive: 43 100.576591 99.690719 14: seq: 1c, analog_in_state oid=35 next_clock=2701130816 value=8827
Receive: 44 100.676697 100.675493 11: seq: 1d, clock clock=2666564815
Receive: 45 100.706592 100.675493 15: seq: 1d, analog_in_state oid=18 next_clock=2724530816 value=31461
Receive: 46 100.746613 100.675493 15: seq: 1d, analog_in_state oid=22 next_clock=2731730816 value=23226
Receive: 47 100.786592 100.675493 15: seq: 1d, analog_in_state oid=26 next_clock=2738930816 value=31465
Receive: 48 100.786613 100.675493 14: seq: 1d, stats count=201 sum=172260 sumsq=1003795
Receive: 49 100.876623 100.675493 14: seq: 1d, analog_in_state oid=35 next_clock=2755130816 value=8829
Receive: 50 101.006588 100.675493 15: seq: 1d, analog_in_state oid=18 next_clock=2778530816 value=31460
Receive: 51 101.046638 100.675493 15: seq: 1d, analog_in_state oid=22 next_clock=2785730816 value=23231
Receive: 52 101.086626 100.675493 15: seq: 1d, analog_in_state oid=26 next_clock=2792930816 value=31462
Receive: 53 101.176762 100.675493 14: seq: 1d, analog_in_state oid=35 next_clock=2809130816 value=8833
Receive: 54 101.306636 100.675493 15: seq: 1d, analog_in_state oid=18 next_clock=2832530816 value=31460
Receive: 55 101.346623 100.675493 15: seq: 1d, analog_in_state oid=22 next_clock=2839730816 value=23225
Receive: 56 101.386615 100.675493 15: seq: 1d, analog_in_state oid=26 next_clock=2846930816 value=31463
Receive: 57 101.476623 100.675493 14: seq: 1d, analog_in_state oid=35 next_clock=2863130816 value=8837
Receive: 58 101.606619 101.528751 15: seq: 1e, analog_in_state oid=18 next_clock=2886530816 value=31461
Receive: 59 101.646625 101.528751 15: seq: 1e, analog_in_state oid=22 next_clock=2893730816 value=23226
Receive: 60 101.661628 101.660760 11: seq: 1f, clock clock=2843869179
Receive: 61 101.686621 101.660760 15: seq: 1f, analog_in_state oid=26 next_clock=2900930816 value=31464
Receive: 62 101.776617 101.660760 14: seq: 1f, analog_in_state oid=35 next_clock=2917130816 value=8840
Receive: 63 101.906625 101.660760 15: seq: 1f, analog_in_state oid=18 next_clock=2940530816 value=31457
Receive: 64 101.946615 101.660760 15: seq: 1f, analog_in_state oid=22 next_clock=2947730816 value=23227
Receive: 65 101.986623 101.660760 15: seq: 1f, analog_in_state oid=26 next_clock=2954930816 value=31465
Receive: 66 102.076651 101.660760 14: seq: 1f, analog_in_state oid=35 next_clock=2971130816 value=8842
Receive: 67 102.206559 101.660760 15: seq: 1f, analog_in_state oid=18 next_clock=2994530816 value=31457
Receive: 68 102.246982 101.660760 15: seq: 1f, analog_in_state oid=22 next_clock=3001730816 value=23229
Receive: 69 102.287108 101.660760 15: seq: 1f, analog_in_state oid=26 next_clock=3008930816 value=31464
Receive: 70 102.376904 101.660760 14: seq: 1f, analog_in_state oid=35 next_clock=3025130816 value=8846
Receive: 71 102.506615 101.660760 15: seq: 1f, analog_in_state oid=18 next_clock=3048530816 value=31459
Receive: 72 102.546613 101.660760 15: seq: 1f, analog_in_state oid=22 next_clock=3055730816 value=23230
Receive: 73 102.586619 101.660760 15: seq: 1f, analog_in_state oid=26 next_clock=3062930816 value=31466
Receive: 74 102.646606 102.645376 11: seq: 10, clock clock=3021173369
Receive: 75 102.676586 102.645376 14: seq: 10, analog_in_state oid=35 next_clock=3079130816 value=8850
Receive: 76 102.806636 102.645376 15: seq: 10, analog_in_state oid=18 next_clock=3102530816 value=31460
Receive: 77 102.846617 102.645376 15: seq: 10, analog_in_state oid=22 next_clock=3109730816 value=23229
Receive: 78 102.886614 102.645376 15: seq: 10, analog_in_state oid=26 next_clock=3116930816 value=31463
Receive: 79 102.976625 102.645376 14: seq: 10, analog_in_state oid=35 next_clock=3133130816 value=8848
Receive: 80 103.106628 102.645376 15: seq: 10, analog_in_state oid=18 next_clock=3156530816 value=31459
Receive: 81 103.146622 102.645376 15: seq: 10, analog_in_state oid=22 next_clock=3163730816 value=23227
Receive: 82 103.186624 102.645376 15: seq: 10, analog_in_state oid=26 next_clock=3170930816 value=31465
Receive: 83 103.276619 102.645376 14: seq: 10, analog_in_state oid=35 next_clock=3187130816 value=8854
Receive: 84 103.406596 102.645376 15: seq: 10, analog_in_state oid=18 next_clock=3210530816 value=31463
Receive: 85 103.446604 102.645376 15: seq: 10, analog_in_state oid=22 next_clock=3217730816 value=23228
Receive: 86 103.486610 102.645376 15: seq: 10, analog_in_state oid=26 next_clock=3224930816 value=31462
Receive: 87 103.576660 102.645376 14: seq: 10, analog_in_state oid=35 next_clock=3241130816 value=8859
Receive: 88 103.630610 103.629956 11: seq: 11, clock clock=3198297771
Receive: 89 103.706594 103.629956 15: seq: 11, analog_in_state oid=18 next_clock=3264530816 value=31459
Receive: 90 103.746623 103.629956 15: seq: 11, analog_in_state oid=22 next_clock=3271730816 value=23229
Receive: 91 103.786621 103.629956 15: seq: 11, analog_in_state oid=26 next_clock=3278930816 value=31463
Receive: 92 103.876617 103.629956 14: seq: 11, analog_in_state oid=35 next_clock=3295130816 value=8860
Receive: 93 103.998586 103.997032 13: seq: 14, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 94 104.001539 103.999651 13: seq: 15, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 95 104.003500 104.002327 13: seq: 16, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 96 104.004589 104.004289 13: seq: 18, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 97 104.005592 104.005312 13: seq: 1a, spi_transfer_response oid=5 response=b'\x00\x00\x00\x00\x00'
Receive: 98 104.006572 104.005312 15: seq: 1a, analog_in_state oid=18 next_clock=3318530816 value=31452
Receive: 99 104.010645 104.009186 12: seq: 1b, shutdown clock=3266519356 static_string_id=Command request
Stats 105.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6071 bytes_read=22786 bytes_retransmit=9 bytes_invalid=0 send_seq=525 receive_seq=525 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004491 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.23 cputime=7.952 memavail=3617140 print_time=118.824 buffer_time=4.265 print_stall=0 extruder: target=200 temp=196.2 pwm=0.000
Stats 106.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=6077 bytes_read=23023 bytes_retransmit=9 bytes_invalid=0 send_seq=526 receive_seq=526 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004362 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.13 cputime=7.976 memavail=3617172 print_time=118.824 buffer_time=3.264 print_stall=0 extruder: target=200 temp=196.8 pwm=0.000
Stats 107.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=6083 bytes_read=23216 bytes_retransmit=9 bytes_invalid=0 send_seq=527 receive_seq=527 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004358 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.13 cputime=8.011 memavail=3617140 print_time=118.824 buffer_time=2.263 print_stall=0 extruder: target=200 temp=197.1 pwm=0.000
Stats 108.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=6089 bytes_read=23439 bytes_retransmit=9 bytes_invalid=0 send_seq=528 receive_seq=528 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004364 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.13 cputime=8.044 memavail=3617172 print_time=118.824 buffer_time=1.262 print_stall=0 extruder: target=200 temp=197.1 pwm=0.000
Stats 109.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=6114 bytes_read=23680 bytes_retransmit=9 bytes_invalid=0 send_seq=530 receive_seq=530 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004415 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.13 cputime=8.071 memavail=3617172 print_time=118.824 buffer_time=0.261 print_stall=0 extruder: target=200 temp=197.2 pwm=0.000
Stats 110.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000006 mcu_task_stddev=0.000009 bytes_write=6120 bytes_read=23860 bytes_retransmit=9 bytes_invalid=0 send_seq=531 receive_seq=531 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004325 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.13 cputime=8.102 memavail=3617124 print_time=118.824 buffer_time=0.000 print_stall=0 extruder: target=200 temp=197.0 pwm=0.000
Stats 111.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6126 bytes_read=24088 bytes_retransmit=9 bytes_invalid=0 send_seq=532 receive_seq=532 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004462 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.04 cputime=8.129 memavail=3617188 print_time=118.824 buffer_time=0.000 print_stall=0 extruder: target=200 temp=196.6 pwm=0.000
Stats 112.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6132 bytes_read=24310 bytes_retransmit=9 bytes_invalid=0 send_seq=533 receive_seq=533 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004310 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.04 cputime=8.168 memavail=3617188 print_time=118.824 buffer_time=0.000 print_stall=0 extruder: target=200 temp=196.0 pwm=0.000
Stats 113.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6138 bytes_read=24503 bytes_retransmit=9 bytes_invalid=0 send_seq=534 receive_seq=534 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004387 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.04 cputime=8.195 memavail=3617124 print_time=118.824 buffer_time=0.000 print_stall=0 extruder: target=200 temp=195.5 pwm=0.000
Stats 114.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6144 bytes_read=24726 bytes_retransmit=9 bytes_invalid=0 send_seq=535 receive_seq=535 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004477 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.04 cputime=8.220 memavail=3617156 print_time=118.824 buffer_time=0.000 print_stall=0 extruder: target=200 temp=194.7 pwm=0.000
Attempting MCU 'mcu' reset command
b'Got EOF when reading from device'
webhooks client 547573508624: Disconnected
Restarting printer
Start printer at Wed Jan 29 14:39:39 2025 (1738161580.0 116.1)
===== Config file =====
[respond]
[gcode_macro CHOPPER_TUNE]
description = Vibrations tests to calculate lowest magnitude drivers registers v1.2
variable_debug = False
variable_inset = 10
variable_current_change_step = 25
variable_measure_time = 1250
variable_required_rpm = [37.5, 150, 1.5]
variable_delay = 500
variable_fclk = 12
gcode =
{% set current_min = params.CURRENT_MIN_MA|default('default')|string|lower %}
{% set current_max = params.CURRENT_MAX_MA|default('default')|string|lower %}
{% set tbl_min = params.TBL_MIN|default(0)|int %}
{% set tbl_max = params.TBL_MAX|default(3)|int %}
{% set toff_min = params.TOFF_MIN|default(1)|int %}
{% set toff_max = params.TOFF_MAX|default(8)|int %}
{% set hstrt_hend_max = params.HSTRT_HEND_MAX|default(16)|int %}
{% set hstrt_min = params.HSTRT_MIN|default(0)|int %}
{% set hstrt_max = params.HSTRT_MAX|default(7)|int %}
{% set hend_min = params.HEND_MIN|default(2)|int %}
{% set hend_max = params.HEND_MAX|default(15)|int %}
{% set tpfd_min = params.TPFD_MIN|default(-1)|int %}
{% set tpfd_max = params.TPFD_MAX|default(-1)|int %}
{% set min_speed = params.MIN_SPEED|default('default')|string|lower %}
{% set max_speed = params.MAX_SPEED|default('default')|string|lower %}
{% set speed_change_step = params.SPEED_CHANGE_STEP|default('default')|string|lower %}
{% set iterations = params.ITERATIONS|default(1)|int %}
{% set travel_distance = params.TRAVEL_DISTANCE|default('default')|string|lower %}
{% set accel_chip = params.ACCELEROMETER|default('default')|string|lower %}
{% set find_vibr = params.FIND_VIBRATIONS|default('False')|string|lower %}
{% set axis = params.AXIS|default('X')|string|lower %}
{% set run_plotter = params.RUN_PLOTTER|default('True')|string|lower %}
_detect_driver stepper={axis}
_chop_workflow axis={axis} {rawparams}
[gcode_shell_command chop_tune]
command = ~/chopper-resonance-tuner/chopper_plot.sh
timeout = 9999.0
verbose = True
[gcode_macro _detect_driver]
description = Find which driver is used in configuration
variable_drivers = '2130', '2208', '2209', '2660', '2240', '5160'
variable_driver = 0
variable_resistor = 0
gcode =
{% set stepper = 'stepper_' + params.STEPPER|string|lower %}
{% for driver in drivers %}
{% if 'run_current' in printer.configfile.config['tmc' + driver + ' ' + stepper] %}
{action_respond_info('Selected tmc%s for %s' % (driver, stepper))}
SET_GCODE_VARIABLE MACRO=_detect_driver VARIABLE=driver VALUE={driver}
{% if driver != '2240' %}
{% set resistor = printer.configfile.settings['tmc' + driver + ' ' + stepper].sense_resistor %}
{% else %}
{% set resistor = printer.configfile.settings['tmc' + driver + ' ' + stepper].rref %}
{% endif %}
SET_GCODE_VARIABLE MACRO=_detect_driver VARIABLE=resistor VALUE={resistor}
{% endif %}
{% endfor %}
[gcode_macro _chop_apply_regs]
variable_registers = 'tbl', 'toff', 'hend', 'hstrt', 'tpfd', 'curr'
variable_amount = 0
variable_tbl = -1
variable_toff = -1
variable_hend = -1
variable_hstrt = -1
variable_tpfd = -1
variable_curr = -1
gcode =
{% if printer['gcode_macro _chop_apply_regs'][params.FIELD]|int != params.VALUE|int %}
{% for stepper in params.STEPPERS.split('-') %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
M118 Setting {params.FIELD|string|lower} from {
printer['gcode_macro _chop_apply_regs'][params.FIELD]|int} to {params.VALUE|int} on {stepper}
{% endif %}
{% if params.FIELD|lower != 'curr' %}
SET_TMC_FIELD STEPPER={stepper} FIELD={params.FIELD} VALUE={params.VALUE|int}
{% else %}
SET_TMC_CURRENT STEPPER={stepper} CURRENT={params.VALUE|int / 1000}
{% endif %}
{% for count in range(1, amount + 1) %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
M118 Setting {params.FIELD|string|lower} from {
printer['gcode_macro _chop_apply_regs'][params.FIELD]|int} to {
params.VALUE|int} on {stepper|string + count|string}
{% endif %}
{% if params.FIELD|lower != 'curr' %}
SET_TMC_FIELD STEPPER={stepper|string + count|string} FIELD={params.FIELD} VALUE={params.VALUE|int}
{% else %}
SET_TMC_CURRENT STEPPER={stepper} CURRENT={params.VALUE|int / 1000}
{% endif %}
{% endfor %}
{% endfor %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE={params.FIELD|string|lower} VALUE={params.VALUE|int}
{% endif %}
[gcode_macro _chop_workflow]
description = Calculate process of CHOPPER_TUNE macro
gcode =
{% set axis = params.AXIS|default('X')|string|lower %}
{% set driver = printer['gcode_macro _detect_driver'].driver|string|lower %}
{% set sense_resistor = printer['gcode_macro _detect_driver'].resistor %}
{% set current_min = params.CURRENT_MIN_MA|default('default')|string|lower %}
{% set current_max = params.CURRENT_MAX_MA|default('default')|string|lower %}
{% set current_change_step = printer['gcode_macro CHOPPER_TUNE'].current_change_step %}
{% set tbl_min = params.TBL_MIN|default(0)|int %}
{% set tbl_max = params.TBL_MAX|default(3)|int %}
{% set toff_min = params.TOFF_MIN|default(1)|int %}
{% set toff_max = params.TOFF_MAX|default(8)|int %}
{% set hstrt_hend_max = params.HSTRT_HEND_MAX|default(16)|int %}
{% set hstrt_min = params.HSTRT_MIN|default(0)|int %}
{% set hstrt_max = params.HSTRT_MAX|default(7)|int %}
{% set hend_min = params.HEND_MIN|default(2)|int %}
{% set hend_max = params.HEND_MAX|default(15)|int %}
{% set tpfd_min = params.TPFD_MIN|default(-1)|int %}
{% set tpfd_max = params.TPFD_MAX|default(-1)|int %}
{% set min_speed = params.MIN_SPEED|default('default')|string|lower %}
{% set max_speed = params.MAX_SPEED|default('default')|string|lower %}
{% set speed_change_step = params.SPEED_CHANGE_STEP|default('default')|string|lower %}
{% set required_rpm = printer['gcode_macro CHOPPER_TUNE'].required_rpm %}
{% set iterations = params.ITERATIONS|default(1)|int %}
{% set travel_distance = params.TRAVEL_DISTANCE|default('default')|string|lower %}
{% set accel_chip = params.ACCELEROMETER|default('default')|string|lower %}
{% set find_vibr = params.FIND_VIBRATIONS|default('False')|string|lower %}
{% set run_plotter = params.RUN_PLOTTER|default('True')|string|lower %}
{% set inset = printer['gcode_macro CHOPPER_TUNE'].inset %}
{% set config = printer.configfile.config %}
{% set settings = printer.configfile.settings %}
{% set measure_time = printer['gcode_macro CHOPPER_TUNE'].measure_time / 1000|float %}
{% set delay = printer['gcode_macro CHOPPER_TUNE'].delay|int %}
{% set fclk = printer['gcode_macro CHOPPER_TUNE'].fclk|int %}
{% set kinematics = config.printer.kinematics|string %}
{% if axis in ['x', 'y', 'z'] %}
{% if kinematics == 'corexy' %}
{% if axis in ['x', 'y'] %}
{% if axis == 'x' %}
{% set axes = ['x', 'y'] %}
{% elif axis == 'y' %}
{% set axes = ['y', 'x'] %}
{% endif %}
{% set steppers = ['stepper_x', 'stepper_y'] %}
{% elif axis == 'z' %}
{% set axes = ['z', 'x'] %}
{% set steppers = ['stepper_z'] %}
{% endif %}
{% elif kinematics == 'cartesian' %}
{% if axis == 'x' %}
{% set axes = ['x', 'y'] %}
{% set steppers = ['stepper_x'] %}
{% elif axis == 'y' %}
{% set axes = ['y', 'x'] %}
{% set steppers = ['stepper_y'] %}
{% elif axis == 'z' %}
{% set axes = ['z', 'x'] %}
{% set steppers = ['stepper_z'] %}
{% endif %}
{% else %}
{action_raise_error('WARNING!!! Script does not support your kinematics')}
{% endif %}
{% if axes[0] == 'z' %}
{% set minAX = (settings['stepper_' + axes[0]].position_min|float, 0)|max + inset %}
{% set acceleration = settings.printer.max_z_accel|int %}
{% set trv_speed = config.printer.max_z_velocity|int / 2 * 60 %}
{% else %}
{% set minAX = settings['stepper_' + axes[0]].position_min|float + inset %}
{% set acceleration = config.printer.max_accel|int %}
{% set trv_speed = config.printer.max_velocity|int / 2 * 60 %}
{% endif %}
{% set maxAX = settings['stepper_' + axes[0]].position_max|float - inset %}
{% set midAX = settings['stepper_' + axes[0]].position_min|float +
((settings['stepper_' + axes[0]].position_max|float -
settings['stepper_' + axes[0]].position_min|float) / 2) %}
{% set midBAX = settings['stepper_' + axes[1]].position_min|float +
((settings['stepper_' + axes[1]].position_max|float -
settings['stepper_' + axes[1]].position_min|float) / 2) %}
{% else %}
{action_raise_error('WARNING!!! Incorrect direction')}
{% endif %}
{% if tpfd_min != -1 or tpfd_max != -1 %}
{% if driver == '5160' or driver == '2240' %}
{% if tpfd_min < 0 or tpfd_max < 0 %}
{action_raise_error('WARNING!!! Incorrect TPFD values')}
{% endif %}
{% else %}
{action_raise_error('WARNING!!! TMC%s not support register TPFD' % (driver))}
{% endif %}
{% endif %}
{% for register in printer['gcode_macro _chop_apply_regs'].registers %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE={register|string|lower} VALUE=-1
{% endfor %}
{% for mot in range(8) %}
{% if ('stepper_' + axes[0] + mot|string) in config %}
SET_GCODE_VARIABLE MACRO=_chop_apply_regs VARIABLE=amount VALUE={mot}
{% if ('stepper_' + axes[0] + (mot + 1)|string) not in config %}
{action_respond_info('Selected %dwd configuration' % (mot + 1))}
{% endif %}
{% elif mot == 1 %}
{action_respond_info('Selected 1wd configuration')}
{% endif %}
{% endfor %}
{% if accel_chip == 'default' %}
{% if 'accel_chip' in config.resonance_tester %}
{% set accel_chip = config.resonance_tester.accel_chip %}
{% else %}
{% set accel_chip = 'adxl345' %}
{% endif %}
{% endif %}
{action_respond_info('Selected %s for accelerometer' % (accel_chip))}
{% if current_min == 'default' %}
{% set current_min = (config['tmc' + driver + ' ' + steppers[0]].run_current|float * 1000)|int %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Set default run_current: %d mA to run_current_min' % (current_min))}
{% endif %}
{% else %}
{% set current_min = current_min|int %}
{% endif %}
{% if current_max == 'default' %}
{% set current_max = (config['tmc' + driver + ' ' + steppers[0]].run_current|float * 1000)|int%}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Set default run_current: %d mA to run_current_max' % (current_max))}
{% endif %}
{% else %}
{% set current_max = current_max|int %}
{% endif %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{% set current_max = current_min %}
{% set tbl_min = settings['tmc' + driver + ' ' + steppers[0]].driver_tbl|int %}
{% set tbl_max = tbl_min %}
{% set toff_min = settings['tmc' + driver + ' ' + steppers[0]].driver_toff|int %}
{% set toff_max = toff_min %}
{% set hstrt_min = settings['tmc' + driver + ' ' + steppers[0]].driver_hstrt|int %}
{% set hstrt_max = hstrt_min %}
{% set hend_min = settings['tmc' + driver + ' ' + steppers[0]].driver_hend|int %}
{% set hend_max = hend_min %}
{% set rotation_dist = config[steppers[0]].rotation_distance|float %}
{% set gear_ratio = (config[steppers[0]].gear_ratio|default('1:1')).split(':') %}
{% set full_steps_per_rotation = config[steppers[0]].full_steps_per_rotation|default(200)|int %}
{% if min_speed == 'default' %}
{% set min_speed = (required_rpm[0] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist)|float %}
{% else %}
{% set min_speed = min_speed|float %}
{% endif %}
{% if max_speed == 'default' %}
{% set max_required_mms = (required_rpm[1] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist)|int %}
{% set max_speed = (((-acceleration * measure_time + ((acceleration * measure_time) ** 2 +
4 * acceleration * (maxAX - minAX)) ** 0.5) / 2), max_required_mms)|min|float %}
{% else %}
{% set max_speed = max_speed|float %}
{% endif %}
{% if speed_change_step == 'default' %}
{% set speed_change_step = required_rpm[2] / 60 * full_steps_per_rotation /
200 / (gear_ratio[0]|int / gear_ratio[1]|int) * rotation_dist %}
{% else %}
{% set speed_change_step = speed_change_step|float %}
{% endif %}
{% else %}
{% if min_speed == 'default' or max_speed == 'default' %}
{action_raise_error('WARNING!!! Resonance speed must be defined')}
{% endif %}
{% set min_speed, max_speed = min_speed|float, max_speed|float %}
{% set speed_change_step = 1 %}
{% endif %}
{% if max_speed > trv_speed / 30 %}
{action_raise_error('WARNING!!! Required speed (%d mm/s) on axis (%s)'
' is faster than kinematics allow, please lower speed or increase'
' speed limit in printer.cfg' % (max_speed, axes[0]))}
{% endif %}
{% set accel_decel_distance = max_speed ** 2 / acceleration %}
{% set auto_travel_distance = accel_decel_distance + (max_speed * measure_time) %}
{% if printer['gcode_macro CHOPPER_TUNE'].debug %}
{action_respond_info('Acceleration & deceleration zone = %f mm' % (accel_decel_distance))}
{action_respond_info('Auto calculated min required travel distance = %f mm' % (auto_travel_distance))}
{% endif %}
{% if travel_distance == 'default' %}
{% if minAX + auto_travel_distance > maxAX %}
{action_raise_error('WARNING!!! Required travel distance on axis (%s)'
' (%.2f mm) is longer than kinematics allows, please lower'
' speed or increase acceleration' % (axes[0], auto_travel_distance))}
{% endif %}
{% set travel_distance = auto_travel_distance %}
{% else %}
{% set travel_distance = travel_distance|int %}
{% if minAX + travel_distance > maxAX %}
{% set travel_distance = maxAX - minAX %}
{% if travel_distance < auto_travel_distance %}
{action_raise_error('WARNING!!! Travel distance on axis (%s) is less than'
' it should be, please increase acceleration or lower speed' % (axes[0]))}
{% else %}
{action_respond_info('WARNING!!! Travel distance on axis (%s)'
' is longer than kinematics allows, lowering...' % (axes[0]))}
{% endif %}
{% else %}
{% if travel_distance < auto_travel_distance %}
{% set travel_distance = auto_travel_distance %}
{% if minAX + auto_travel_distance > maxAX %}
{action_raise_error('WARNING!!! Travel distance on axis (%s) is less'
' than required (%.2f mm), and longer than kinematics allows, please lower'
' speed or increase acceleration' % (axes[0], auto_travel_distance))}
{% endif %}
{% endif %}
{% endif %}
{% endif %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{action_respond_info('Final max travel distance = %.2f mm, position min = %.2f, traveling: %.2f --> %.2f' %
(travel_distance, minAX, minAX, travel_distance + minAX))}
{action_respond_info('Start find vibration mode, speed: %.2f --> %.2f mm/s with %.2f step current=%d TBL=%d TOFF=%d'
' HSTRT=%d HEND=%d' % (min_speed, max_speed, speed_change_step, current_min, tbl_min, toff_min, hstrt_min, hend_min))}
{% else %}
{action_respond_info('Final travel distance = %.2f mm, position min = %.2f, traveling: %.2f --> %.2f' %
(travel_distance, minAX, minAX, travel_distance + minAX))}
{action_respond_info('Start of register enumeration mode, speed: %.2f --> %.2f mm/s current: %d'
' --> %d mA iterations=%d TBL: %d --> %d TOFF: %d --> %d HSTRT: %d --> %d HEND: %d --> %d TPFD:'
' %d --> %d' % (min_speed, max_speed, current_min, current_max, iterations, tbl_min, tbl_max,
toff_min, toff_max, hstrt_min, hstrt_max, hend_min, hend_max, tpfd_min, tpfd_max))}
{% endif %}
{% if not 'xyz' in printer.toolhead.homed_axes %}
G28 X Y Z
{% endif %}
SET_VELOCITY_LIMIT ACCEL={acceleration}
SET_VELOCITY_LIMIT ACCEL_TO_DECEL={acceleration}
G0 {axes[0]}{minAX} {axes[1]}{midBAX} F{trv_speed}
RUN_SHELL_COMMAND CMD=chop_tune PARAMS='cleaner'
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME=stand_still
G4 P5000
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME=stand_still
{% for current in range(current_min, current_max + 1, current_change_step) %}
_chop_apply_regs steppers={steppers|join('-')} field=curr value={current}
{% for tbl in range(tbl_min, tbl_max + 1) %}
_chop_apply_regs steppers={steppers|join('-')} field=tbl value={tbl}
{% for toff in range(toff_min, toff_max + 1) %}
_chop_apply_regs steppers={steppers|join('-')} field=toff value={toff}
{% for hstrt_value in range(hstrt_min, hstrt_max + 1) %}
{% for hend_value in range(hend_min, hend_max + 1) %}
{% if hend_value + hstrt_value <= hstrt_hend_max %}
_chop_apply_regs steppers={steppers|join('-')} field=hend value={hend_value}
_chop_apply_regs steppers={steppers|join('-')} field=hstrt value={hstrt_value}
{% for tpfd in range(tpfd_min, tpfd_max + 1) %}
{% if tpfd_min != -1 and tpfd_max != -1 %}
_chop_apply_regs steppers={steppers|join('-')} field=tpfd value={tpfd}
{% endif %}
DUMP_TMC STEPPER={steppers[0]} REGISTER=chopconf
{% set freq = 1/(2*(12+32*toff)*1/(1000000*fclk)+2*1/(1000000*fclk)*16*(1.5**tbl)) %}
{% for speed in range((min_speed * 100)|int, (max_speed * 100)|int + 1, (speed_change_step * 100)|int) %}
{% set speed = speed / 100 %}
{% for i in range(iterations) %}
{% if find_vibr == 'true' or find_vibr == '1' %}
{% set travel_distance = (travel_distance / max_speed) * speed %}
G4 P{delay}
M118 Speed {speed|round(2)} mm/s on {travel_distance|round(2)} mm
{% endif %}
{% set name = '__%d_%d_%d_%d_%d_%d_%d_%d_%d__' %
(current, tbl, toff, hstrt_value, hend_value, tpfd, speed*100, freq, i+1) %}
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME={name}
G0 {axes[0]}{minAX + travel_distance} F{speed*60}
ACCELEROMETER_MEASURE CHIP={accel_chip} NAME={name}
G0 {axes[0]}{minAX} F{trv_speed}
M400
{% endfor %}
{% endfor %}
{% endfor %}
{% endif %}
{% endfor %}
{% endfor %}
{% endfor %}
{% endfor %}
{% endfor %}
{% if tpfd_min == -1 or tpfd_max == -1 %}
{% set tpfd_min, tpfd_max = 0, 0 %}
{% endif %}
G4 P500
G0 {axis}{midAX} F{trv_speed}
{% if run_plotter == 'true' or run_plotter == '1' %}
M118 Magnitude graphs generation...
M118 This may take a while, please wait
RUN_SHELL_COMMAND CMD=chop_tune PARAMS='{'iterations=%d driver=%s sense_resistor=%f'%(iterations, driver, sense_resistor)}'
{% endif %}
M118 For run parser manually type - RUN_SHELL_COMMAND CMD=chop_tune PARAMS='{'iterations=%d driver=%s sense_resistor=%f'%
(iterations, driver, sense_resistor)}'
[virtual_sdcard]
path = ~/printer_data/gcodes
on_error_gcode = CANCEL_PRINT
[pause_resume]
[display_status]
[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = BASE_CANCEL_PRINT
gcode =
TURN_OFF_HEATERS
CLEAR_PAUSE
SDCARD_RESET_FILE
BASE_CANCEL_PRINT
G90
G0 X350 Y350 F3600
SET_SKEW CLEAR=1
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=0
[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set idle_timeout = client.idle_timeout|default(0) %}
{% set temp = printer[printer.toolhead.extruder].target if printer.toolhead.extruder != '' else 0 %}
{% set restore = False if printer.toolhead.extruder == ''
else True if params.RESTORE|default(1)|int == 1 else False %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=last_extruder_temp VALUE="{{'restore': restore, 'temp': temp}}"
{% if idle_timeout > 0 %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=restore_idle_timeout VALUE={printer.configfile.settings.idle_timeout.timeout}
SET_IDLE_TIMEOUT TIMEOUT={idle_timeout}
{% endif %}
PAUSE_BASE
{client.user_pause_macro|default("")}
_TOOLHEAD_PARK_PAUSE_CANCEL {rawparams}
[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
variable_last_extruder_temp = {'restore': False, 'temp': 0}
variable_restore_idle_timeout = 0
variable_idle_state = False
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set sp_move = client.speed_move|default(velocity) %}
{% set runout_resume = True if client.runout_sensor|default("") == ""
else True if not printer[client.runout_sensor].enabled
else printer[client.runout_sensor].filament_detected %}
{% set can_extrude = True if printer.toolhead.extruder == ''
else printer[printer.toolhead.extruder].can_extrude %}
{% set do_resume = False %}
{% set prompt_txt = [] %}
{% if printer.idle_timeout.state|upper == "IDLE" or idle_state %}
SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=idle_state VALUE=False
{% if last_extruder_temp.restore %}
RESPOND TYPE=echo MSG='{"Restoring \"%s\" temperature to %3.1f\u00B0C, this may take some time" % (printer.toolhead.extruder, last_extruder_temp.temp) }'
M109 S{last_extruder_temp.temp}
{% set do_resume = True %}
{% elif can_extrude %}
{% set do_resume = True %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}'
{% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %}
{% endif %}
{% elif can_extrude %}
{% set do_resume = True %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}'
{% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %}
{% endif %}
{% if runout_resume %}
{% if do_resume %}
{% if restore_idle_timeout > 0 %} SET_IDLE_TIMEOUT TIMEOUT={restore_idle_timeout} {% endif %}
{client.user_resume_macro|default("")}
_CLIENT_EXTRUDE
RESUME_BASE VELOCITY={params.VELOCITY|default(sp_move)}
{% endif %}
{% else %}
RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]}'
{% set _d = prompt_txt.append("\"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]) %}
{% endif %}
{% if not (runout_resume and do_resume) %}
RESPOND TYPE=command MSG="action:prompt_begin RESUME aborted !!!"
{% for element in prompt_txt %}
RESPOND TYPE=command MSG='{"action:prompt_text %s" % element}'
{% endfor %}
RESPOND TYPE=command MSG="action:prompt_footer_button Ok|RESPOND TYPE=command MSG=action:prompt_end|info"
RESPOND TYPE=command MSG="action:prompt_show"
{% endif %}
[gcode_macro SET_PAUSE_NEXT_LAYER]
description = Enable a pause if the next layer is reached
gcode =
{% set pause_next_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_next_layer %}
{% set ENABLE = params.ENABLE|default(1)|int != 0 %}
{% set MACRO = params.MACRO|default(pause_next_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_next_layer VALUE="{{ 'enable': ENABLE, 'call': MACRO }}"
[gcode_macro SET_PAUSE_AT_LAYER]
description = Enable/disable a pause if a given layer number is reached
gcode =
{% set pause_at_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_at_layer %}
{% set ENABLE = params.ENABLE|int != 0 if params.ENABLE is defined
else params.LAYER is defined %}
{% set LAYER = params.LAYER|default(pause_at_layer.layer)|int %}
{% set MACRO = params.MACRO|default(pause_at_layer.call, True) %}
SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_at_layer VALUE="{{ 'enable': ENABLE, 'layer': LAYER, 'call': MACRO }}"
[gcode_macro SET_PRINT_STATS_INFO]
rename_existing = SET_PRINT_STATS_INFO_BASE
description = Overwrite, to get pause_next_layer and pause_at_layer feature
variable_pause_next_layer = { 'enable': False, 'call': "PAUSE" }
variable_pause_at_layer = { 'enable': False, 'layer': 0, 'call': "PAUSE" }
gcode =
{% if pause_next_layer.enable %}
RESPOND TYPE=echo MSG='{"%s, forced by pause_next_layer" % pause_next_layer.call}'
{pause_next_layer.call}
SET_PAUSE_NEXT_LAYER ENABLE=0
{% elif pause_at_layer.enable and params.CURRENT_LAYER is defined and params.CURRENT_LAYER|int == pause_at_layer.layer %}
RESPOND TYPE=echo MSG='{"%s, forced by pause_at_layer [%d]" % (pause_at_layer.call, pause_at_layer.layer)}'
{pause_at_layer.call}
SET_PAUSE_AT_LAYER ENABLE=0
{% endif %}
SET_PRINT_STATS_INFO_BASE {rawparams}
[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL]
description = Helper: park toolhead used in PAUSE and CANCEL_PRINT
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set velocity = printer.configfile.settings.pause_resume.recover_velocity %}
{% set use_custom = client.use_custom_pos|default(false)|lower == 'true' %}
{% set custom_park_x = client.custom_park_x|default(0.0) %}
{% set custom_park_y = client.custom_park_y|default(0.0) %}
{% set park_dz = client.custom_park_dz|default(2.0)|abs %}
{% set sp_hop = client.speed_hop|default(15) * 60 %}
{% set sp_move = client.speed_move|default(velocity) * 60 %}
{% set origin = printer.gcode_move.homing_origin %}
{% set act = printer.gcode_move.gcode_position %}
{% set max = printer.toolhead.axis_maximum %}
{% set cone = printer.toolhead.cone_start_z|default(max.z) %}
{% set round_bed = True if printer.configfile.settings.printer.kinematics is in ['delta','polar','rotary_delta','winch']
else False %}
{% set z_min = params.Z_MIN|default(0)|float %}
{% set z_park = [[(act.z + park_dz), z_min]|max, (max.z - origin.z)]|min %}
{% set x_park = params.X if params.X is defined
else custom_park_x if use_custom
else 0.0 if round_bed
else (max.x - 5.0) %}
{% set y_park = params.Y if params.Y is defined
else custom_park_y if use_custom
else (max.y - 5.0) if round_bed and z_park < cone
else 0.0 if round_bed
else (max.y - 5.0) %}
_CLIENT_RETRACT
{% if "xyz" in printer.toolhead.homed_axes %}
G90
G1 Z{z_park} F{sp_hop}
G1 X{x_park} Y{y_park} F{sp_move}
{% if not printer.gcode_move.absolute_coordinates %} G91 {% endif %}
{% else %}
RESPOND TYPE=echo MSG='Printer not homed'
{% endif %}
[gcode_macro _CLIENT_EXTRUDE]
description = Extrudes, if the extruder is hot enough
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set use_fw_retract = (client.use_fw_retract|default(false)|lower == 'true') and (printer.firmware_retraction is defined) %}
{% set length = params.LENGTH|default(client.unretract)|default(1.0)|float %}
{% set speed = params.SPEED|default(client.speed_unretract)|default(35) %}
{% set absolute_extrude = printer.gcode_move.absolute_extrude %}
{% if printer.toolhead.extruder != '' %}
{% if printer[printer.toolhead.extruder].can_extrude %}
{% if use_fw_retract %}
{% if length < 0 %}
G10
{% else %}
G11
{% endif %}
{% else %}
M83
G1 E{length} F{(speed|float|abs) * 60}
{% if absolute_extrude %}
M82
{% endif %}
{% endif %}
{% else %}
RESPOND TYPE=echo MSG='{"\"%s\" not hot enough" % printer.toolhead.extruder}'
{% endif %}
{% endif %}
[gcode_macro _CLIENT_RETRACT]
description = Retracts, if the extruder is hot enough
gcode =
{% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %}
{% set length = params.LENGTH|default(client.retract)|default(1.0)|float %}
{% set speed = params.SPEED|default(client.speed_retract)|default(35) %}
_CLIENT_EXTRUDE LENGTH=-{length|float|abs} SPEED={speed|float|abs}
[autotune_tmc stepper_x]
motor = omc-17me15-1504s
tuning_goal = performance
voltage = 48
tbl = 0
toff = 1
[autotune_tmc stepper_y]
motor = omc-17me15-1504s
tuning_goal = performance
voltage = 48
tbl = 0
toff = 1
[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE
gcode =
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set bed_mesh_min = printer.configfile.settings.bed_mesh.mesh_min %}
{% set bed_mesh_max = printer.configfile.settings.bed_mesh.mesh_max %}
{% set probe_count = printer.configfile.settings.bed_mesh.probe_count %}
{% set kamp_settings = printer["gcode_macro _KAMP_Settings"] %}
{% set verbose_enable = kamp_settings.verbose_enable | abs %}
{% set probe_dock_enable = kamp_settings.probe_dock_enable | abs %}
{% set attach_macro = kamp_settings.attach_macro | string %}
{% set detach_macro = kamp_settings.detach_macro | string %}
{% set mesh_margin = kamp_settings.mesh_margin | float %}
{% set fuzz_amount = kamp_settings.fuzz_amount | float %}
{% set probe_count = probe_count if probe_count|length > 1 else probe_count * 2 %}
{% set max_probe_point_distance_x = ( bed_mesh_max[0] - bed_mesh_min[0] ) / (probe_count[0] - 1) %}
{% set max_probe_point_distance_y = ( bed_mesh_max[1] - bed_mesh_min[1] ) / (probe_count[1] - 1) %}
{% set x_min = all_points | map(attribute=0) | min | default(bed_mesh_min[0]) %}
{% set y_min = all_points | map(attribute=1) | min | default(bed_mesh_min[1]) %}
{% set x_max = all_points | map(attribute=0) | max | default(bed_mesh_max[0]) %}
{% set y_max = all_points | map(attribute=1) | max | default(bed_mesh_max[1]) %}
{% set fuzz_range = range((0) | int, (fuzz_amount * 100) | int + 1) %}
{% set adapted_x_min = x_min - mesh_margin - (fuzz_range | random / 100.0) %}
{% set adapted_y_min = y_min - mesh_margin - (fuzz_range | random / 100.0) %}
{% set adapted_x_max = x_max + mesh_margin + (fuzz_range | random / 100.0) %}
{% set adapted_y_max = y_max + mesh_margin + (fuzz_range | random / 100.0) %}
{% set adapted_x_min = [adapted_x_min , bed_mesh_min[0]] | max %}
{% set adapted_y_min = [adapted_y_min , bed_mesh_min[1]] | max %}
{% set adapted_x_max = [adapted_x_max , bed_mesh_max[0]] | min %}
{% set adapted_y_max = [adapted_y_max , bed_mesh_max[1]] | min %}
{% set points_x = (((adapted_x_max - adapted_x_min) / max_probe_point_distance_x) | round(method='ceil') | int) + 1 %}
{% set points_y = (((adapted_y_max - adapted_y_min) / max_probe_point_distance_y) | round(method='ceil') | int) + 1 %}
{% if (([points_x, points_y]|max) > 6) %}
{% set algorithm = "bicubic" %}
{% set min_points = 4 %}
{% else %}
{% set algorithm = "lagrange" %}
{% set min_points = 3 %}
{% endif %}
{% set points_x = [points_x , min_points]|max %}
{% set points_y = [points_y , min_points]|max %}
{% set points_x = [points_x , probe_count[0]]|min %}
{% set points_y = [points_y , probe_count[1]]|min %}
{% if verbose_enable == True %}
{% if printer.exclude_object.objects != [] %}
{ action_respond_info( "Algorithm: {}.".format(
(algorithm),
)) }
{ action_respond_info("Default probe count: {},{}.".format(
(probe_count[0]),
(probe_count[1]),
)) }
{ action_respond_info("Adapted probe count: {},{}.".format(
(points_x),
(points_y),
)) }
{action_respond_info("Default mesh bounds: {}, {}.".format(
(bed_mesh_min[0],bed_mesh_min[1]),
(bed_mesh_max[0],bed_mesh_max[1]),
)) }
{% if mesh_margin > 0 %}
{action_respond_info("Mesh margin is {}, mesh bounds extended by {}mm.".format(
(mesh_margin),
(mesh_margin),
)) }
{% else %}
{action_respond_info("Mesh margin is 0, margin not increased.")}
{% endif %}
{% if fuzz_amount > 0 %}
{action_respond_info("Mesh point fuzzing enabled, points fuzzed up to {}mm.".format(
(fuzz_amount),
)) }
{% else %}
{action_respond_info("Fuzz amount is 0, mesh points not fuzzed.")}
{% endif %}
{ action_respond_info("Adapted mesh bounds: {}, {}.".format(
(adapted_x_min, adapted_y_min),
(adapted_x_max, adapted_y_max),
)) }
{action_respond_info("KAMP adjustments successful. Happy KAMPing!")}
{% else %}
{action_respond_info("No objects detected! Check your gcode and make sure that EXCLUDE_OBJECT_DEFINE is happening before BED_MESH_CALIBRATE is called. Defaulting to regular meshing.")}
G4 P5000
{% endif %}
{% endif %}
{% if probe_dock_enable == True %}
{attach_macro}
{% endif %}
_BED_MESH_CALIBRATE mesh_min={adapted_x_min},{adapted_y_min} mesh_max={adapted_x_max},{adapted_y_max} ALGORITHM={algorithm} PROBE_COUNT={points_x},{points_y}
{% if probe_dock_enable == True %}
{detach_macro}
{% endif %}
[gcode_macro LINE_PURGE]
description = A purge macro that adapts to be near your actual printed objects
gcode =
{% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
{% set cross_section = printer.configfile.settings.extruder.max_extrude_cross_section | float %}
{% if printer.firmware_retraction is defined %}
{% set RETRACT = G10 | string %}
{% set UNRETRACT = G11 | string %}
{% else %}
{% set RETRACT = 'G1 E-.5 F2100' | string %}
{% set UNRETRACT = 'G1 E.5 F2100' | string %}
{% endif %}
{% set verbose_enable = printer["gcode_macro _KAMP_Settings"].verbose_enable | abs %}
{% set purge_height = printer["gcode_macro _KAMP_Settings"].purge_height | float %}
{% set tip_distance = printer["gcode_macro _KAMP_Settings"].tip_distance | float %}
{% set purge_margin = printer["gcode_macro _KAMP_Settings"].purge_margin | float %}
{% set purge_amount = printer["gcode_macro _KAMP_Settings"].purge_amount | float %}
{% set flow_rate = printer["gcode_macro _KAMP_Settings"].flow_rate | float %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set purge_x_min = (all_points | map(attribute=0) | min | default(0)) %}
{% set purge_x_max = (all_points | map(attribute=0) | max | default(0)) %}
{% set purge_y_min = (all_points | map(attribute=1) | min | default(0)) %}
{% set purge_y_max = (all_points | map(attribute=1) | max | default(0)) %}
{% set purge_x_center = ([((purge_x_max + purge_x_min) / 2) - (purge_amount / 2), 0] | max) %}
{% set purge_y_center = ([((purge_y_max + purge_y_min) / 2) - (purge_amount / 2), 0] | max) %}
{% set purge_x_origin = ([purge_x_min - purge_margin, 0] | max) %}
{% set purge_y_origin = ([purge_y_min - purge_margin, 0] | max) %}
{% set purge_move_speed = (flow_rate / 5.0) * 60 | float %}
{% if cross_section < 5 %}
{action_respond_info("[Extruder] max_extrude_cross_section is insufficient for purge, please set it to 5 or greater. Purge skipped.")}
{% else %}
{% if verbose_enable == True %}
{action_respond_info("Moving filament tip {}mms".format(
(tip_distance),
)) }
{% endif %}
{% if printer.firmware_retraction is defined %}
{action_respond_info("KAMP purge is using firmware retraction.")}
{% else %}
{action_respond_info("KAMP purge is not using firmware retraction, it is recommended to configure it.")}
{% endif %}
{% if purge_y_origin > 0 %}
{action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm3/s.".format(
(purge_x_center),
(purge_y_origin),
(purge_amount),
(flow_rate),
)) }
{% else %}
{action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm3/s.".format(
(purge_x_origin),
(purge_y_center),
(purge_amount),
(flow_rate),
)) }
{% endif %}
SAVE_GCODE_STATE NAME=Prepurge_State
{% if purge_y_origin > 0 %}
G92 E0
G0 F{travel_speed}
G90
G0 X{purge_x_center} Y{purge_y_origin}
G0 Z{purge_height}
M83
G1 E{tip_distance} F{purge_move_speed}
G1 X{purge_x_center + purge_amount} E{purge_amount} F{purge_move_speed}
{RETRACT}
G0 X{purge_x_center + purge_amount + 10} F{travel_speed}
G92 E0
M82
G0 Z{purge_height * 2} F{travel_speed}
{% else %}
G92 E0
G0 F{travel_speed}
G90
G0 X{purge_x_origin} Y{purge_y_center}
G0 Z{purge_height}
M83
G1 E{tip_distance} F{purge_move_speed}
G1 Y{purge_y_center + purge_amount} E{purge_amount} F{purge_move_speed}
{RETRACT}
G0 Y{purge_y_center + purge_amount + 10} F{travel_speed}
G92 E0
M82
G0 Z{purge_height * 2} F{travel_speed}
{% endif %}
RESTORE_GCODE_STATE NAME=Prepurge_State
{% endif %}
[gcode_macro SMART_PARK]
description = Parks your printhead near the print area for pre-print hotend heating.
gcode =
{% set kamp_settings = printer["gcode_macro _KAMP_Settings"] %}
{% set z_height = kamp_settings.smart_park_height | float %}
{% set purge_margin = kamp_settings.purge_margin | float %}
{% set verbose_enable = kamp_settings.verbose_enable | abs %}
{% set center_x = printer.toolhead.axis_maximum.x / 2 | float %}
{% set center_y = printer.toolhead.axis_maximum.y / 2 | float %}
{% set axis_minimum_x = printer.toolhead.axis_minimum.x | float %}
{% set axis_minimum_y = printer.toolhead.axis_minimum.y | float %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set x_min = all_points | map(attribute=0) | min | default(center_x) %}
{% set y_min = all_points | map(attribute=1) | min | default(center_y) %}
{% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
{% if purge_margin > 0 and x_min != center_x and y_min != center_y %}
{% set x_min = [ x_min - purge_margin , x_min ] | min %}
{% set y_min = [ y_min - purge_margin , y_min ] | min %}
{% set x_min = [ x_min , axis_minimum_x ] | max %}
{% set y_min = [ y_min , axis_minimum_y ] | max %}
{% endif %}
{% if verbose_enable == True %}
{ action_respond_info("Smart Park location: {},{}.".format(
(x_min),
(y_min),
)) }
{% endif %}
SAVE_GCODE_STATE NAME=Presmartpark_State
G90
{% if printer.toolhead.position.z < z_height %}
G0 Z{z_height}
{% endif %}
G0 X{x_min} Y{y_min} F{travel_speed}
G0 Z{z_height}
RESTORE_GCODE_STATE NAME=Presmartpark_State
[gcode_macro _KAMP_Settings]
description = This macro contains all adjustable settings for KAMP
variable_verbose_enable = True
variable_mesh_margin = 5
variable_fuzz_amount = 0
variable_probe_dock_enable = False
variable_attach_macro = 'Attach_Probe'
variable_detach_macro = 'Dock_Probe'
variable_purge_height = 0.8
variable_tip_distance = 0
variable_purge_margin = 10
variable_purge_amount = 30
variable_flow_rate = 12
variable_smart_park_height = 10
gcode =
{action_respond_info(" Running the KAMP_Settings macro does nothing, it is only used for storing KAMP settings. ")}
[gcode_macro _TAP_VARIABLES]
variable_probing = 0
variable_brushed = 0
gcode =
[gcode_macro _PRE_PROBE_CHECK]
gcode =
{% set svv = printer.save_variables.variables %}
{% set PROBE_TEMP = svv.probe_temp %}
{% set MAX_TEMP = PROBE_TEMP + 5 %}
{% set ACTUAL_TEMP = printer.extruder.temperature %}
{% set TARGET_TEMP = printer.extruder.target %}
{% set PROBE_ACCEL = printer["gcode_macro _TAP_SETTINGS"].probe_accel %}
{% set BRUSHED = printer["gcode_macro _TAP_VARIABLES"].brushed %}
{% if BRUSHED == 1 %}
_PROBE_TEMP_CHECK
{% else %}
NOZZLE_BRUSH
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=1
_PROBE_TEMP_CHECK
{% endif %}
[gcode_macro _PROBE_TEMP_CHECK]
gcode =
{% set svv = printer.save_variables.variables %}
{% set PROBE_TEMP = svv.probe_temp %}
{% set MAX_TEMP = PROBE_TEMP + 5 %}
{% set ACTUAL_TEMP = printer.extruder.temperature %}
{% set TARGET_TEMP = printer.extruder.target %}
{% set PROBE_ACCEL = printer["gcode_macro _TAP_SETTINGS"].probe_accel %}
SET_KINEMATICS_LIMIT Z_ACCEL={PROBE_ACCEL}
{% if TARGET_TEMP > PROBE_TEMP %}
{ action_respond_info('Extruder temperature target of %.1fC is too high, lowering to %.1fC' % (TARGET_TEMP, PROBE_TEMP)) }
M109 S{PROBE_TEMP}
{% else %}
{% if ACTUAL_TEMP > MAX_TEMP %}
{ action_respond_info('Extruder temperature %.1fC is still too high, waiting until below %.1fC' % (ACTUAL_TEMP, MAX_TEMP)) }
TEMPERATURE_WAIT SENSOR=extruder MAXIMUM={MAX_TEMP}
{% endif %}
{% endif %}
[gcode_macro _POST_PROBING]
gcode =
SET_KINEMATICS_LIMIT Z_ACCEL={printer["gcode_macro _TAP_SETTINGS"].max_z_accel}
[gcode_macro _POST_PROBE]
gcode =
POST_PROBE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
[gcode_macro SET_PROBE_TEMP]
gcode =
{% set temp = params.TEMP|int %}
SAVE_VARIABLE VARIABLE=probe_temp VALUE={TEMP}
[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_REAL
gcode =
Z_TILT_ADJUST_REAL
POST_PROBE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
[gcode_macro _TAP_SETTINGS]
variable_probe_accel = 15
variable_home_x = 175
variable_home_y = 175
variable_home_speed = 100
variable_max_z_accel = 30
gcode =
[mcu]
serial = /dev/serial/by-id/usb-Klipper_stm32f446xx_JKYZ-if00
[danger_options]
allow_plugin_override = True
[printer]
square_corner_velocity = 500.0
kinematics = limited_corexy
max_velocity = 564
max_z_velocity = 30
max_accel = 20000
max_x_accel = 20000
max_y_accel = 19000
max_z_accel = 30
scale_xy_accel = True
[thermistor NTC10K]
temperature1 = 0.0
resistance1 = 32116.0
temperature2 = 40.0
resistance2 = 5309.0
temperature3 = 80.0
resistance3 = 1228.0
[stepper_y]
step_pin = PE11
dir_pin = PE10
enable_pin = !PE9
rotation_distance = 40
microsteps = 32
full_steps_per_rotation = 200
endstop_pin = PB13
position_min = 0
position_endstop = 350
position_max = 350
homing_speed = 60
homing_retract_dist = 0
homing_positive_dir = true
step_pulse_duration = 0.000004
[tmc5160 stepper_y]
cs_pin = PE7
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = true
run_current = 1.3
sense_resistor = 0.033
driver_tbl = 0
driver_toff = 1
driver_hstrt = 0
driver_hend = 10
driver_tpfd = 1
[stepper_x]
step_pin = PD8
dir_pin = PB12
enable_pin = !PD9
rotation_distance = 40
microsteps = 32
full_steps_per_rotation = 200
endstop_pin = PB14
position_min = 0
step_pulse_duration = 0.000004
position_endstop = 350
position_max = 350
homing_speed = 60
homing_retract_dist = 0
homing_positive_dir = true
[tmc5160 stepper_x]
cs_pin = PE15
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = true
run_current = 1.3
sense_resistor = 0.033
driver_tbl = 0
driver_toff = 1
driver_hstrt = 0
driver_hend = 10
driver_tpfd = 1
[stepper_z]
step_pin = PE2
dir_pin = PE4
enable_pin = !PE3
rotation_distance = 4
microsteps = 32
endstop_pin = probe:z_virtual_endstop
position_max = 290
position_min = -5
homing_speed = 50
second_homing_speed = 10
homing_retract_dist = 3
[tmc2209 stepper_z]
uart_pin = PC15
uart_address = 0
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[stepper_z1]
step_pin = PE1
dir_pin = PE0
enable_pin = !PC5
rotation_distance = 4
microsteps = 32
[tmc2209 stepper_z1]
uart_pin = PD11
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[stepper_z2]
step_pin = PD12
dir_pin = PC4
enable_pin = !PE8
rotation_distance = 4
microsteps = 32
[tmc2209 stepper_z2]
uart_pin = PA15
interpolate = True
run_current = 1.0
hold_current = 1.0
sense_resistor = 0.110
stealthchop_threshold = 0
[extruder]
step_pin = PE6
dir_pin = !PC13
enable_pin = !PE5
rotation_distance = 4.637
microsteps = 16
full_steps_per_rotation = 200
nozzle_diameter = 0.600
filament_diameter = 1.75
heater_pin = PB15
sensor_type = PT1000
sensor_pin = PC0
min_temp = 10
max_temp = 315
max_power = 1.0
min_extrude_temp = 170
heater_power = 65
cooling_fan = fan_generic fan0
ambient_temp_sensor = heater_generic chamber_heater
pressure_advance = 0.05
pressure_advance_smooth_time = 0.040
max_extrude_cross_section = 5
pid_version = 1
pid_target = 285.00
pid_tolerance = 0.0200
pid_kp = 18.086
pid_ki = 0.536
pid_kd = 152.599
control = mpc
block_heat_capacity = 16.6237
sensor_responsiveness = 0.0731558
ambient_transfer = 0.110661
fan_ambient_transfer = 0.110661, 0.194043, 0.24027
[tmc5160 extruder]
cs_pin = PC14
spi_software_miso_pin = PE13
spi_software_mosi_pin = PE14
spi_software_sclk_pin = PE12
interpolate = True
run_current = 0.5
hold_current = 0.5
sense_resistor = 0.033
[verify_heater extruder]
hysteresis = 20
heating_gain = 0.2
check_gain_time = 120
[heater_bed]
heater_pin = PB3
sensor_type = Generic 3950
sensor_pin = PC1
max_power = 0.8
min_temp = 5
max_temp = 170
pid_version = 1
pid_target = 105.00
pid_tolerance = 0.0200
control = pid
pid_kp = 51.427
pid_ki = 1.894
pid_kd = 349.061
[probe]
pin = PA3
x_offset = 0
y_offset = 0
speed = 50.0
samples = 4
samples_result = median
sample_retract_dist = 3.0
samples_tolerance = 0.1
samples_tolerance_retries = 5
deactivate_on_each_sample = True
activate_gcode =
_PRE_PROBE_CHECK
deactivate_gcode =
_POST_PROBING
z_offset = -1.930
[safe_z_home]
home_xy_position = 175, 175
z_hop = 5
[heater_fan hotend_fan]
pin = PA13
max_power = 1.0
kick_start_time = 0.5
heater = extruder
heater_temp = 50.0
fan_speed = 1.0
[fan_generic fan0]
pin = PA8
max_power = 1.0
kick_start_time = 0.1
off_below = 0.05
cycle_time = 0.00005
[idle_timeout]
timeout = 9999999999
[bed_mesh]
speed = 100
horizontal_move_z = 10
mesh_min = 40, 40
mesh_max = 310,310
fade_start = 0.6
fade_end = 10.0
probe_count = 7,7
algorithm = bicubic
adaptive_margin = 5
[z_tilt]
z_positions =
-50, 18
150, 348
350, 18
points =
30, 5
175, 295
320, 5
speed = 100
horizontal_move_z = 10
retries = 10
retry_tolerance = 0.007
[gcode_macro G32]
gcode =
BED_MESH_CLEAR
G28
Z_TILT_ADJUST
G28
G0 X175 Y175 Z30 F3600
[save_variables]
filename = ~/printer_data/config/variables.cfg
[gcode_macro _PREHEAT]
gcode =
SET_HEATER_TEMPERATURE HEATER=extruder TARGET={printer.extruder.filament.extruder}
SET_HEATER_TEMPERATURE HEATER=bed TARGET={printer.extruder.filament.bed}
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={printer.extruder.filament.chamber}
[gcode_macro _COOLOFF]
gcode =
SET_HEATER_TEMPERATURE HEATER=extruder TARGET=0
SET_HEATER_TEMPERATURE HEATER=bed TARGET=0
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
SET_FAN_SPEED FAN=fan2 SPEED=1.0
[gcode_macro PRINT_START]
gcode =
{% set chamber = printer.extruder.filament.chamber %}
SET_FAN_SPEED FAN=fan0 SPEED=0.0
SET_FAN_SPEED FAN=fan2 SPEED=0.0
G28
SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={printer.extruder.filament.chamber}
TEMPERATURE_WAIT SENSOR="heater_generic chamber_heater" MINIMUM={printer.extruder.filament.chamber}
SET_HEATER_TEMPERATURE HEATER=chamber_heater target=0
G28 Z
BED_MESH_CALIBRATE
SET_GCODE_VARIABLE MACRO=_TAP_VARIABLES VARIABLE=brushed VALUE=0
G92 E0
G90
LINE_PURGE
[gcode_macro PRINT_END]
gcode =
M400
G92 E0
G1 E-1.0 F3600
G91
G0 Z1.00 X20.0 Y20.0 F20000
TURN_OFF_HEATERS
M107
G90
G0 X350 Y350 F3600
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=0
[exclude_object]
[gcode_arcs]
resolution = 0.1
[input_shaper]
smoother_freq_x = 56.6
smoother_freq_y = 30.8
shaper_type_x = smooth_zvd_ei
shaper_freq_x = 41.6
shaper_type_y = smooth_ei
shaper_freq_y = 26.6
[filaments]
on_set_filament_gcode =
M117 add
on_clear_filament_gcode =
M117 clear
[z_thermal_adjust]
temp_coeff = 0.005
smooth_time = 1
sensor_type = NTC10K
sensor_pin = PB0
min_temp = 10
max_temp = 77
gcode_id = thermal_adjust
[led led_strip]
red_pin = PB6
green_pin = PB5
blue_pin = PB7
[heater_generic chamber_heater]
heater_pin = PC8
max_power = 1.0
sensor_type = Generic 3950
sensor_pin = PB1
min_temp = 10
max_temp = 75
pid_version = 1
pid_target = 60.00
pid_tolerance = 0.0200
control = pid
pid_kp = 64.228
pid_ki = 0.421
pid_kd = 2450.039
[heater_fan chamber_heater_fan]
pin = PB2
max_power = 1.0
heater = chamber_heater
heater_temp = 35
[verify_heater chamber_heater]
hysteresis = 10
heating_gain = 0.1
check_gain_time = 600
[fan_generic fan2]
pin = !PD1
cycle_time = 0.00005
kick_start_time = 0.1
off_below = 0.07
[gcode_macro M106]
gcode =
{% set fan = 'fan' + (params.P|int if params.P is defined else 0)|string %}
{% set speed = (params.S|float / 255 if params.S is defined else 1.0) %}
SET_FAN_SPEED FAN={fan} SPEED={speed}
[gcode_macro _ENABLE_FAN]
variable_fan_on = 0
gcode =
{% if printer["gcode_macro _ENABLE_FAN"].fan_on == 0 %}
SET_FAN_SPEED FAN=fan0 SPEED={printer.extruder.filament.part_cooling}
SET_FAN_SPEED FAN=fan2 SPEED={printer.extruder.filament.aux_cooling}
SET_GCODE_VARIABLE MACRO=_ENABLE_FAN VARIABLE=fan_on VALUE=1
{% endif %}
[skew_correction]
[pid_profile extruder abs]
pid_version = 1
pid_target = 260.00
pid_tolerance = 0.0200
control = pid
pid_kp = 16.100
pid_ki = 1.058
pid_kd = 61.259
[pid_profile heater_bed abs]
pid_version = 1
pid_target = 105.00
pid_tolerance = 0.0200
control = pid
pid_kp = 51.427
pid_ki = 1.894
pid_kd = 349.061
[skew_correction skew]
xy_skew = 0.000
xz_skew = 0.000
yz_skew = 0.000
[pid_profile extruder pc]
pid_version = 1
pid_target = 250.00
pid_tolerance = 0.0200
control = pid
pid_kp = 17.627
pid_ki = 1.013
pid_kd = 76.678
[bed_mesh default]
version = 1
points =
-0.080000, 0.003125, 0.086875
-0.013438, 0.047187, 0.126875
0.057187, 0.112812, 0.140312
x_count = 3
y_count = 3
mesh_x_pps = 2
mesh_y_pps = 2
algo = lagrange
tension = 0.2
min_x = 161.25
max_x = 188.75
min_y = 161.25
max_y = 188.75
[cpap_heater]
pid_version = 1
pid_target = 40.00
pid_tolerance = 0.0200
control = pid
pid_kp = 8.528
pid_ki = 0.070
pid_kd = 260.544
=======================
DEBUG: registering extruder
DEBUG: registering extruder#: extruder
Extruder max_extrude_ratio=2.078758
mcu 'mcu': Starting serial connect
webhooks client 547570756208: New connection
webhooks client 547570756208: Client info {'program': 'Moonraker', 'version': 'v0.9.3-1-g4e00a07'}
Loaded MCU 'mcu' 105 commands ( v0.10.0-557-gf7e29b27 / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-12+11) 2.31.1)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c3=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 CLOCK_FREQ=180000000 MCU=stm32f446xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
TMC extruder failed to init: Unable to write tmc spi 'extruder' register GLOBALSCALER
Starting heater checks for extruder
Starting heater checks for heater_bed
bed_mesh: generated points
Index | Tool Adjusted | Probe
0 | (40.0, 40.0) | (40.0, 40.0)
1 | (85.0, 40.0) | (85.0, 40.0)
2 | (130.0, 40.0) | (130.0, 40.0)
3 | (175.0, 40.0) | (175.0, 40.0)
4 | (220.0, 40.0) | (220.0, 40.0)
5 | (265.0, 40.0) | (265.0, 40.0)
6 | (310.0, 40.0) | (310.0, 40.0)
7 | (310.0, 85.0) | (310.0, 85.0)
8 | (265.0, 85.0) | (265.0, 85.0)
9 | (220.0, 85.0) | (220.0, 85.0)
10 | (175.0, 85.0) | (175.0, 85.0)
11 | (130.0, 85.0) | (130.0, 85.0)
12 | (85.0, 85.0) | (85.0, 85.0)
13 | (40.0, 85.0) | (40.0, 85.0)
14 | (40.0, 130.0) | (40.0, 130.0)
15 | (85.0, 130.0) | (85.0, 130.0)
16 | (130.0, 130.0) | (130.0, 130.0)
17 | (175.0, 130.0) | (175.0, 130.0)
18 | (220.0, 130.0) | (220.0, 130.0)
19 | (265.0, 130.0) | (265.0, 130.0)
20 | (310.0, 130.0) | (310.0, 130.0)
21 | (310.0, 175.0) | (310.0, 175.0)
22 | (265.0, 175.0) | (265.0, 175.0)
23 | (220.0, 175.0) | (220.0, 175.0)
24 | (175.0, 175.0) | (175.0, 175.0)
25 | (130.0, 175.0) | (130.0, 175.0)
26 | (85.0, 175.0) | (85.0, 175.0)
27 | (40.0, 175.0) | (40.0, 175.0)
28 | (40.0, 220.0) | (40.0, 220.0)
29 | (85.0, 220.0) | (85.0, 220.0)
30 | (130.0, 220.0) | (130.0, 220.0)
31 | (175.0, 220.0) | (175.0, 220.0)
32 | (220.0, 220.0) | (220.0, 220.0)
33 | (265.0, 220.0) | (265.0, 220.0)
34 | (310.0, 220.0) | (310.0, 220.0)
35 | (310.0, 265.0) | (310.0, 265.0)
36 | (265.0, 265.0) | (265.0, 265.0)
37 | (220.0, 265.0) | (220.0, 265.0)
38 | (175.0, 265.0) | (175.0, 265.0)
39 | (130.0, 265.0) | (130.0, 265.0)
40 | (85.0, 265.0) | (85.0, 265.0)
41 | (40.0, 265.0) | (40.0, 265.0)
42 | (40.0, 310.0) | (40.0, 310.0)
43 | (85.0, 310.0) | (85.0, 310.0)
44 | (130.0, 310.0) | (130.0, 310.0)
45 | (175.0, 310.0) | (175.0, 310.0)
46 | (220.0, 310.0) | (220.0, 310.0)
47 | (265.0, 310.0) | (265.0, 310.0)
48 | (310.0, 310.0) | (310.0, 310.0)
Starting heater checks for chamber_heater
autotune_tmc set stepper_x pwm_freq=2
autotune_tmc stepper_x ncycles=219 pfdcycles=73
autotune_tmc set stepper_x tpfd=1
autotune_tmc set stepper_x tbl=1
autotune_tmc set stepper_x toff=1
autotune_tmc seting hysteresis based on 48.0 V
dcoilblank = 0.018462, dcoilsd = 0.003683
hysteresis = 1, htotal = 1, hstrt = 1, hend = 0
autotune_tmc set stepper_x hstrt=0
autotune_tmc set stepper_x hend=3
autotune_tmc using max PWM speed 595.876107
autotune_tmc set stepper_x pwm_autoscale=True
autotune_tmc set stepper_x pwm_autograd=True
autotune_tmc set stepper_x pwm_grad=3
autotune_tmc set stepper_x pwm_ofs=21
autotune_tmc set stepper_x pwm_reg=15
autotune_tmc set stepper_x pwm_lim=4
autotune_tmc set stepper_x tpwmthrs=1048575
autotune_tmc set stepper_x en_pwm_mode=False
autotune_tmc set stepper_x tcoolthrs=313(30.0)
autotune_tmc set stepper_x sgt=1
autotune_tmc set stepper_x small_hysteresis=False
autotune_tmc set stepper_x semin=2
autotune_tmc set stepper_x semax=4
autotune_tmc set stepper_x seup=3
autotune_tmc set stepper_x sedn=2
autotune_tmc set stepper_x seimin=1
autotune_tmc set stepper_x sfilt=0
autotune_tmc set stepper_x iholddelay=12
autotune_tmc set stepper_x vhighfs=False
autotune_tmc set stepper_x vhighchm=False
autotune_tmc set stepper_x multistep_filt=True
autotune_tmc set stepper_y pwm_freq=2
autotune_tmc stepper_y ncycles=219 pfdcycles=73
autotune_tmc set stepper_y tpfd=1
autotune_tmc set stepper_y tbl=1
autotune_tmc set stepper_y toff=1
autotune_tmc seting hysteresis based on 48.0 V
dcoilblank = 0.018462, dcoilsd = 0.003683
hysteresis = 1, htotal = 1, hstrt = 1, hend = 0
autotune_tmc set stepper_y hstrt=0
autotune_tmc set stepper_y hend=3
autotune_tmc using max PWM speed 595.876107
autotune_tmc set stepper_y pwm_autoscale=True
autotune_tmc set stepper_y pwm_autograd=True
autotune_tmc set stepper_y pwm_grad=3
autotune_tmc set stepper_y pwm_ofs=21
autotune_tmc set stepper_y pwm_reg=15
autotune_tmc set stepper_y pwm_lim=4
autotune_tmc set stepper_y tpwmthrs=1048575
autotune_tmc set stepper_y en_pwm_mode=False
autotune_tmc set stepper_y tcoolthrs=313(30.0)
autotune_tmc set stepper_y sgt=1
autotune_tmc set stepper_y small_hysteresis=False
autotune_tmc set stepper_y semin=2
autotune_tmc set stepper_y semax=4
autotune_tmc set stepper_y seup=3
autotune_tmc set stepper_y sedn=2
autotune_tmc set stepper_y seimin=1
autotune_tmc set stepper_y sfilt=0
autotune_tmc set stepper_y iholddelay=12
autotune_tmc set stepper_y vhighfs=False
autotune_tmc set stepper_y vhighchm=False
autotune_tmc set stepper_y multistep_filt=True
Stats 119.8: gcodein=0 mcu: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=4914 bytes_read=7604 bytes_retransmit=9 bytes_invalid=0 send_seq=407 receive_seq=407 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180030434 heater_bed: target=0 temp=0.0 pwm=0.000 z_thermal_adjust: temp=0.0 chamber_heater: target=0 temp=0.0 pwm=0.000 sysload=2.20 cputime=11.265 memavail=3615764 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=0.0 pwm=0.000
Stats 120.8: gcodein=0 mcu: mcu_awake=0.011 mcu_task_avg=0.000011 mcu_task_stddev=0.000012 bytes_write=4920 bytes_read=7769 bytes_retransmit=9 bytes_invalid=0 send_seq=408 receive_seq=408 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180049960 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.42 cputime=11.323 memavail=3615328 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=189.8 pwm=0.000
Stats 121.8: gcodein=0 mcu: mcu_awake=0.011 mcu_task_avg=0.000011 mcu_task_stddev=0.000012 bytes_write=4942 bytes_read=7997 bytes_retransmit=9 bytes_invalid=0 send_seq=410 receive_seq=410 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180037407 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.42 cputime=11.379 memavail=3615108 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=189.3 pwm=0.000
Stats 122.8: gcodein=0 mcu: mcu_awake=0.011 mcu_task_avg=0.000011 mcu_task_stddev=0.000012 bytes_write=4948 bytes_read=8204 bytes_retransmit=9 bytes_invalid=0 send_seq=411 receive_seq=411 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180015707 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.42 cputime=11.411 memavail=3615044 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=188.7 pwm=0.000
Stats 123.8: gcodein=0 mcu: mcu_awake=0.011 mcu_task_avg=0.000011 mcu_task_stddev=0.000012 bytes_write=4954 bytes_read=8412 bytes_retransmit=9 bytes_invalid=0 send_seq=412 receive_seq=412 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180020475 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.42 cputime=11.436 memavail=3615172 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=188.1 pwm=0.000
Stats 124.8: gcodein=0 mcu: mcu_awake=0.011 mcu_task_avg=0.000011 mcu_task_stddev=0.000012 bytes_write=4960 bytes_read=8635 bytes_retransmit=9 bytes_invalid=0 send_seq=413 receive_seq=413 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180022652 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.42 cputime=11.464 memavail=3615080 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=187.4 pwm=0.000
Stats 125.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4966 bytes_read=8856 bytes_retransmit=9 bytes_invalid=0 send_seq=414 receive_seq=414 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180016684 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.39 cputime=11.499 memavail=3615240 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=186.1 pwm=0.000
Stats 126.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4972 bytes_read=9064 bytes_retransmit=9 bytes_invalid=0 send_seq=415 receive_seq=415 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180015104 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.39 cputime=11.525 memavail=3615344 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=185.4 pwm=0.000
Stats 127.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4978 bytes_read=9287 bytes_retransmit=9 bytes_invalid=0 send_seq=416 receive_seq=416 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180013486 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.39 cputime=11.558 memavail=3615248 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=184.3 pwm=0.000
Stats 128.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4984 bytes_read=9494 bytes_retransmit=9 bytes_invalid=0 send_seq=417 receive_seq=417 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180012288 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.39 cputime=11.582 memavail=3615312 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=182.7 pwm=0.000
Stats 129.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4990 bytes_read=9702 bytes_retransmit=9 bytes_invalid=0 send_seq=418 receive_seq=418 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180012361 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.39 cputime=11.612 memavail=3615408 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=181.8 pwm=0.000
Stats 130.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4996 bytes_read=9939 bytes_retransmit=9 bytes_invalid=0 send_seq=419 receive_seq=419 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180013416 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=11.637 memavail=3615312 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=180.8 pwm=0.000
Stats 131.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5002 bytes_read=10146 bytes_retransmit=9 bytes_invalid=0 send_seq=420 receive_seq=420 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180010550 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.28 cputime=11.668 memavail=3615444 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=179.7 pwm=0.000
Stats 132.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5008 bytes_read=10354 bytes_retransmit=9 bytes_invalid=0 send_seq=421 receive_seq=421 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180011491 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.28 cputime=11.695 memavail=3615156 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=178.7 pwm=0.000
Stats 133.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5014 bytes_read=10577 bytes_retransmit=9 bytes_invalid=0 send_seq=422 receive_seq=422 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180009713 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.28 cputime=11.721 memavail=3615284 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=177.6 pwm=0.000
Stats 134.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5020 bytes_read=10784 bytes_retransmit=9 bytes_invalid=0 send_seq=423 receive_seq=423 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180010135 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.28 cputime=11.752 memavail=3615324 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=176.3 pwm=0.000
Stats 135.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5026 bytes_read=11006 bytes_retransmit=9 bytes_invalid=0 send_seq=424 receive_seq=424 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180008398 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.18 cputime=11.776 memavail=3615264 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=175.4 pwm=0.000
Stats 136.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5032 bytes_read=11229 bytes_retransmit=9 bytes_invalid=0 send_seq=425 receive_seq=425 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180008097 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.18 cputime=11.807 memavail=3615360 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=174.3 pwm=0.000
Stats 137.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5038 bytes_read=11436 bytes_retransmit=9 bytes_invalid=0 send_seq=426 receive_seq=426 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180007561 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.18 cputime=11.832 memavail=3615296 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=173.3 pwm=0.000
Stats 138.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5044 bytes_read=11635 bytes_retransmit=9 bytes_invalid=0 send_seq=427 receive_seq=427 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180007249 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.18 cputime=11.868 memavail=3615232 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=172.4 pwm=0.000
Stats 139.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5050 bytes_read=11846 bytes_retransmit=9 bytes_invalid=0 send_seq=428 receive_seq=428 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180007083 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.18 cputime=11.896 memavail=3615296 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=171.4 pwm=0.000
Stats 140.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5056 bytes_read=12066 bytes_retransmit=9 bytes_invalid=0 send_seq=429 receive_seq=429 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180006825 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=2.16 cputime=11.920 memavail=3615360 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=170.5 pwm=0.000
Stats 141.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5062 bytes_read=12274 bytes_retransmit=9 bytes_invalid=0 send_seq=430 receive_seq=430 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180006350 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.16 cputime=11.957 memavail=3615400 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=169.4 pwm=0.000
Stats 142.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5068 bytes_read=12497 bytes_retransmit=9 bytes_invalid=0 send_seq=431 receive_seq=431 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180006766 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.16 cputime=11.982 memavail=3615788 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=168.4 pwm=0.000
Stats 143.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5074 bytes_read=12704 bytes_retransmit=9 bytes_invalid=0 send_seq=432 receive_seq=432 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180006140 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.16 cputime=12.015 memavail=3615932 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=167.4 pwm=0.000
Stats 144.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5086 bytes_read=12928 bytes_retransmit=9 bytes_invalid=0 send_seq=434 receive_seq=434 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005480 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.16 cputime=12.040 memavail=3615788 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=166.6 pwm=0.000
Stats 145.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5092 bytes_read=13165 bytes_retransmit=9 bytes_invalid=0 send_seq=435 receive_seq=435 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005719 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.07 cputime=12.074 memavail=3615788 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=165.9 pwm=0.000
Stats 146.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5098 bytes_read=13372 bytes_retransmit=9 bytes_invalid=0 send_seq=436 receive_seq=436 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005420 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.07 cputime=12.112 memavail=3615920 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=164.7 pwm=0.000
Stats 147.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5104 bytes_read=13580 bytes_retransmit=9 bytes_invalid=0 send_seq=437 receive_seq=437 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005292 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.07 cputime=12.136 memavail=3615920 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=163.6 pwm=0.000
Stats 148.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5110 bytes_read=13803 bytes_retransmit=9 bytes_invalid=0 send_seq=438 receive_seq=438 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005545 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.07 cputime=12.169 memavail=3615920 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=162.9 pwm=0.000
Stats 149.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5116 bytes_read=14010 bytes_retransmit=9 bytes_invalid=0 send_seq=439 receive_seq=439 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005474 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=2.07 cputime=12.203 memavail=3615892 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=161.8 pwm=0.000
Stats 150.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5122 bytes_read=14232 bytes_retransmit=9 bytes_invalid=0 send_seq=440 receive_seq=440 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005681 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.98 cputime=12.227 memavail=3615764 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=160.8 pwm=0.000
Stats 151.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5128 bytes_read=14455 bytes_retransmit=9 bytes_invalid=0 send_seq=441 receive_seq=441 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005312 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.98 cputime=12.267 memavail=3615760 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=160.2 pwm=0.000
Stats 152.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5134 bytes_read=14662 bytes_retransmit=9 bytes_invalid=0 send_seq=442 receive_seq=442 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004984 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.98 cputime=12.316 memavail=3615760 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=159.2 pwm=0.000
Stats 153.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5140 bytes_read=14870 bytes_retransmit=9 bytes_invalid=0 send_seq=443 receive_seq=443 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004752 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.98 cputime=12.347 memavail=3615792 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=158.3 pwm=0.000
Stats 154.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5146 bytes_read=15093 bytes_retransmit=9 bytes_invalid=0 send_seq=444 receive_seq=444 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004674 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.98 cputime=12.372 memavail=3615860 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=157.4 pwm=0.000
Stats 155.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5152 bytes_read=15314 bytes_retransmit=9 bytes_invalid=0 send_seq=445 receive_seq=445 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005061 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.90 cputime=12.403 memavail=3615796 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=156.6 pwm=0.000
Stats 156.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5158 bytes_read=15522 bytes_retransmit=9 bytes_invalid=0 send_seq=446 receive_seq=446 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005050 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.90 cputime=12.428 memavail=3615920 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=155.7 pwm=0.000
Stats 157.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5164 bytes_read=15745 bytes_retransmit=9 bytes_invalid=0 send_seq=447 receive_seq=447 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004894 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.90 cputime=12.463 memavail=3615892 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=155.0 pwm=0.000
Stats 158.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5170 bytes_read=15952 bytes_retransmit=9 bytes_invalid=0 send_seq=448 receive_seq=448 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004907 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.90 cputime=12.488 memavail=3615860 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=153.9 pwm=0.000
Stats 159.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5176 bytes_read=16160 bytes_retransmit=9 bytes_invalid=0 send_seq=449 receive_seq=449 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004837 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.90 cputime=12.519 memavail=3615892 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=153.0 pwm=0.000
Stats 160.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5182 bytes_read=16397 bytes_retransmit=9 bytes_invalid=0 send_seq=450 receive_seq=450 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004885 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.83 cputime=12.552 memavail=3615924 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=152.6 pwm=0.000
Stats 161.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5188 bytes_read=16604 bytes_retransmit=9 bytes_invalid=0 send_seq=451 receive_seq=451 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004968 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.83 cputime=12.580 memavail=3616012 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=151.5 pwm=0.000
Stats 162.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5194 bytes_read=16801 bytes_retransmit=9 bytes_invalid=0 send_seq=452 receive_seq=452 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005239 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.83 cputime=12.604 memavail=3616048 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=150.6 pwm=0.000
Stats 163.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5200 bytes_read=17013 bytes_retransmit=9 bytes_invalid=0 send_seq=453 receive_seq=453 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005452 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.83 cputime=12.628 memavail=3615952 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=149.9 pwm=0.000
Stats 164.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5206 bytes_read=17220 bytes_retransmit=9 bytes_invalid=0 send_seq=454 receive_seq=454 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005544 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.83 cputime=12.659 memavail=3616080 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=149.1 pwm=0.000
Stats 165.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5212 bytes_read=17457 bytes_retransmit=9 bytes_invalid=0 send_seq=455 receive_seq=455 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005278 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.76 cputime=12.684 memavail=3615984 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=148.4 pwm=0.000
Stats 166.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5218 bytes_read=17665 bytes_retransmit=9 bytes_invalid=0 send_seq=456 receive_seq=456 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005258 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.76 cputime=12.713 memavail=3615952 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=147.5 pwm=0.000
Stats 167.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5224 bytes_read=17872 bytes_retransmit=9 bytes_invalid=0 send_seq=457 receive_seq=457 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005226 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.76 cputime=12.737 memavail=3615952 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=146.5 pwm=0.000
Stats 168.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5230 bytes_read=18095 bytes_retransmit=9 bytes_invalid=0 send_seq=458 receive_seq=458 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005185 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.76 cputime=12.773 memavail=3616016 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=145.6 pwm=0.000
Stats 169.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5236 bytes_read=18303 bytes_retransmit=9 bytes_invalid=0 send_seq=459 receive_seq=459 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180005061 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.76 cputime=12.821 memavail=3616048 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=145.0 pwm=0.000
Stats 170.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5242 bytes_read=18524 bytes_retransmit=9 bytes_invalid=0 send_seq=460 receive_seq=460 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004866 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.70 cputime=12.850 memavail=3615984 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=144.0 pwm=0.000
Stats 171.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5248 bytes_read=18747 bytes_retransmit=9 bytes_invalid=0 send_seq=461 receive_seq=461 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004951 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.70 cputime=12.875 memavail=3615984 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=143.4 pwm=0.000
Stats 172.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5254 bytes_read=18955 bytes_retransmit=9 bytes_invalid=0 send_seq=462 receive_seq=462 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004893 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.70 cputime=12.907 memavail=3615824 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=142.7 pwm=0.000
Stats 173.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5260 bytes_read=19162 bytes_retransmit=9 bytes_invalid=0 send_seq=463 receive_seq=463 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004772 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.70 cputime=12.932 memavail=3616052 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=141.8 pwm=0.000
Stats 174.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5266 bytes_read=19385 bytes_retransmit=9 bytes_invalid=0 send_seq=464 receive_seq=464 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004654 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.70 cputime=12.976 memavail=3615892 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=141.0 pwm=0.000
Stats 175.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5272 bytes_read=19607 bytes_retransmit=9 bytes_invalid=0 send_seq=465 receive_seq=465 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004489 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.65 cputime=13.004 memavail=3616084 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=140.4 pwm=0.000
Stats 176.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5278 bytes_read=19814 bytes_retransmit=9 bytes_invalid=0 send_seq=466 receive_seq=466 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004376 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.65 cputime=13.029 memavail=3615992 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=139.4 pwm=0.000
Stats 177.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5284 bytes_read=20037 bytes_retransmit=9 bytes_invalid=0 send_seq=467 receive_seq=467 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004495 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.65 cputime=13.061 memavail=3615928 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=138.8 pwm=0.000
Stats 178.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5290 bytes_read=20245 bytes_retransmit=9 bytes_invalid=0 send_seq=468 receive_seq=468 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004415 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.65 cputime=13.084 memavail=3616156 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=138.3 pwm=0.000
Stats 179.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5296 bytes_read=20452 bytes_retransmit=9 bytes_invalid=0 send_seq=469 receive_seq=469 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004500 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.65 cputime=13.116 memavail=3615992 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=137.1 pwm=0.000
Stats 180.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5302 bytes_read=20689 bytes_retransmit=9 bytes_invalid=0 send_seq=470 receive_seq=470 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004428 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.59 cputime=13.141 memavail=3616152 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=136.7 pwm=0.000
Stats 181.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5308 bytes_read=20897 bytes_retransmit=9 bytes_invalid=0 send_seq=471 receive_seq=471 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004348 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.59 cputime=13.168 memavail=3615896 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=136.1 pwm=0.000
Stats 182.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5314 bytes_read=21104 bytes_retransmit=9 bytes_invalid=0 send_seq=472 receive_seq=472 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004236 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.59 cputime=13.192 memavail=3616056 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=135.0 pwm=0.000
Stats 183.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5320 bytes_read=21327 bytes_retransmit=9 bytes_invalid=0 send_seq=473 receive_seq=473 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004283 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.59 cputime=13.231 memavail=3616092 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=134.5 pwm=0.000
Stats 184.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5326 bytes_read=21535 bytes_retransmit=9 bytes_invalid=0 send_seq=474 receive_seq=474 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004317 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.59 cputime=13.272 memavail=3616108 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=133.7 pwm=0.000
Stats 185.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5332 bytes_read=21756 bytes_retransmit=9 bytes_invalid=0 send_seq=475 receive_seq=475 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004523 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.55 cputime=13.297 memavail=3616076 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=133.0 pwm=0.000
Stats 186.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5338 bytes_read=21966 bytes_retransmit=9 bytes_invalid=0 send_seq=476 receive_seq=476 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004559 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.55 cputime=13.332 memavail=3616108 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=132.3 pwm=0.000
Stats 187.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5344 bytes_read=22166 bytes_retransmit=9 bytes_invalid=0 send_seq=477 receive_seq=477 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004609 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.55 cputime=13.364 memavail=3616044 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=131.7 pwm=0.000
Stats 188.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5350 bytes_read=22373 bytes_retransmit=9 bytes_invalid=0 send_seq=478 receive_seq=478 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004582 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.55 cputime=13.389 memavail=3616104 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=130.8 pwm=0.000
Stats 189.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5356 bytes_read=22596 bytes_retransmit=9 bytes_invalid=0 send_seq=479 receive_seq=479 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004741 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.55 cputime=13.421 memavail=3616104 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=130.3 pwm=0.000
Stats 190.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5362 bytes_read=22818 bytes_retransmit=9 bytes_invalid=0 send_seq=480 receive_seq=480 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004717 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.50 cputime=13.445 memavail=3616104 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=129.5 pwm=0.000
Stats 191.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5368 bytes_read=23025 bytes_retransmit=9 bytes_invalid=0 send_seq=481 receive_seq=481 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004581 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.50 cputime=13.480 memavail=3616040 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=128.6 pwm=0.000
Stats 192.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5374 bytes_read=23248 bytes_retransmit=9 bytes_invalid=0 send_seq=482 receive_seq=482 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004642 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.50 cputime=13.521 memavail=3616104 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=128.1 pwm=0.000
Stats 193.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5380 bytes_read=23456 bytes_retransmit=9 bytes_invalid=0 send_seq=483 receive_seq=483 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004561 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.50 cputime=13.546 memavail=3616264 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=127.5 pwm=0.000
Stats 194.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5386 bytes_read=23663 bytes_retransmit=9 bytes_invalid=0 send_seq=484 receive_seq=484 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004445 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.50 cputime=13.581 memavail=3616048 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=126.8 pwm=0.000
Stats 195.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5392 bytes_read=23900 bytes_retransmit=9 bytes_invalid=0 send_seq=485 receive_seq=485 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004420 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.46 cputime=13.617 memavail=3615972 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=126.1 pwm=0.000
Stats 196.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5398 bytes_read=24108 bytes_retransmit=9 bytes_invalid=0 send_seq=486 receive_seq=486 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004318 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.46 cputime=13.641 memavail=3616068 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=125.4 pwm=0.000
Stats 197.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5404 bytes_read=24315 bytes_retransmit=9 bytes_invalid=0 send_seq=487 receive_seq=487 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004236 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.46 cputime=13.676 memavail=3615940 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=124.7 pwm=0.000
Stats 198.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5410 bytes_read=24538 bytes_retransmit=9 bytes_invalid=0 send_seq=488 receive_seq=488 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004206 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.46 cputime=13.727 memavail=3616068 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=124.1 pwm=0.000
Stats 199.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5416 bytes_read=24746 bytes_retransmit=9 bytes_invalid=0 send_seq=489 receive_seq=489 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004127 heater_bed: target=0 temp=21.9 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.46 cputime=13.763 memavail=3615976 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=123.7 pwm=0.000
Stats 200.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5422 bytes_read=24967 bytes_retransmit=9 bytes_invalid=0 send_seq=490 receive_seq=490 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004138 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.42 cputime=13.788 memavail=3616012 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=122.6 pwm=0.000
Stats 201.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5428 bytes_read=25190 bytes_retransmit=9 bytes_invalid=0 send_seq=491 receive_seq=491 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004161 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.42 cputime=13.826 memavail=3615904 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=122.3 pwm=0.000
Stats 202.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5434 bytes_read=25412 bytes_retransmit=9 bytes_invalid=0 send_seq=492 receive_seq=492 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004308 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.42 cputime=13.873 memavail=3615944 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=121.5 pwm=0.000
Stats 203.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5440 bytes_read=25605 bytes_retransmit=9 bytes_invalid=0 send_seq=493 receive_seq=493 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004410 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.42 cputime=13.897 memavail=3616072 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=120.8 pwm=0.000
Stats 204.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5446 bytes_read=25828 bytes_retransmit=9 bytes_invalid=0 send_seq=494 receive_seq=494 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004572 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.42 cputime=13.931 memavail=3616072 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=120.4 pwm=0.000
Stats 205.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5458 bytes_read=26080 bytes_retransmit=9 bytes_invalid=0 send_seq=496 receive_seq=496 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004730 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.39 cputime=13.971 memavail=3616036 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=119.6 pwm=0.000
Stats 206.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5464 bytes_read=26273 bytes_retransmit=9 bytes_invalid=0 send_seq=497 receive_seq=497 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004607 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.39 cputime=13.996 memavail=3616180 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=119.1 pwm=0.000
Stats 207.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5470 bytes_read=26496 bytes_retransmit=9 bytes_invalid=0 send_seq=498 receive_seq=498 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004718 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.39 cputime=14.031 memavail=3616148 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=118.5 pwm=0.000
Stats 208.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5476 bytes_read=26718 bytes_retransmit=9 bytes_invalid=0 send_seq=499 receive_seq=499 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004840 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.39 cputime=14.056 memavail=3616116 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=117.7 pwm=0.000
Stats 209.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5482 bytes_read=26911 bytes_retransmit=9 bytes_invalid=0 send_seq=500 receive_seq=500 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004757 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.39 cputime=14.089 memavail=3616180 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=117.2 pwm=0.000
Stats 210.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5488 bytes_read=27133 bytes_retransmit=9 bytes_invalid=0 send_seq=501 receive_seq=501 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004660 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.36 cputime=14.122 memavail=3616156 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=116.7 pwm=0.000
Stats 211.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5494 bytes_read=27349 bytes_retransmit=9 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004650 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.36 cputime=14.147 memavail=3616092 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=115.9 pwm=0.000
Stats 212.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5500 bytes_read=27542 bytes_retransmit=9 bytes_invalid=0 send_seq=503 receive_seq=503 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004738 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.36 cputime=14.180 memavail=3616140 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=115.4 pwm=0.000
Stats 213.8: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5506 bytes_read=27765 bytes_retransmit=9 bytes_invalid=0 send_seq=504 receive_seq=504 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004631 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.36 cputime=14.205 memavail=3616044 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=114.9 pwm=0.000
Stats 214.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5512 bytes_read=27987 bytes_retransmit=9 bytes_invalid=0 send_seq=505 receive_seq=505 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004667 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.36 cputime=14.239 memavail=3615892 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=114.2 pwm=0.000
Stats 215.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5518 bytes_read=28194 bytes_retransmit=9 bytes_invalid=0 send_seq=506 receive_seq=506 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004787 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.33 cputime=14.272 memavail=3615836 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=113.7 pwm=0.000
Stats 216.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5524 bytes_read=28432 bytes_retransmit=9 bytes_invalid=0 send_seq=507 receive_seq=507 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004735 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.33 cputime=14.298 memavail=3615996 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=113.2 pwm=0.000
Stats 217.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5530 bytes_read=28639 bytes_retransmit=9 bytes_invalid=0 send_seq=508 receive_seq=508 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004698 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.33 cputime=14.328 memavail=3615900 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=112.4 pwm=0.000
Stats 218.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5536 bytes_read=28832 bytes_retransmit=9 bytes_invalid=0 send_seq=509 receive_seq=509 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004740 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.33 cputime=14.351 memavail=3615996 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=111.8 pwm=0.000
Stats 219.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5542 bytes_read=29070 bytes_retransmit=9 bytes_invalid=0 send_seq=510 receive_seq=510 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004857 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.33 cputime=14.386 memavail=3615900 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=111.4 pwm=0.000
Stats 220.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5548 bytes_read=29291 bytes_retransmit=9 bytes_invalid=0 send_seq=511 receive_seq=511 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004882 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.38 cputime=14.418 memavail=3615868 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=110.6 pwm=0.000
Stats 221.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5554 bytes_read=29484 bytes_retransmit=9 bytes_invalid=0 send_seq=512 receive_seq=512 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004973 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.38 cputime=14.441 memavail=3615744 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=110.2 pwm=0.000
Stats 222.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5560 bytes_read=29722 bytes_retransmit=9 bytes_invalid=0 send_seq=513 receive_seq=513 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004864 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.38 cputime=14.480 memavail=3615568 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=109.7 pwm=0.000
Stats 223.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5566 bytes_read=29929 bytes_retransmit=9 bytes_invalid=0 send_seq=514 receive_seq=514 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004917 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=21.9 pwm=0.000 sysload=1.38 cputime=14.507 memavail=3616040 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=109.2 pwm=0.000
Stats 224.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5572 bytes_read=30122 bytes_retransmit=9 bytes_invalid=0 send_seq=515 receive_seq=515 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004785 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.38 cputime=14.548 memavail=3615812 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=108.5 pwm=0.000
Stats 225.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5578 bytes_read=30374 bytes_retransmit=9 bytes_invalid=0 send_seq=516 receive_seq=516 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004771 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.51 cputime=14.577 memavail=3615796 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=108.2 pwm=0.000
Stats 226.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5584 bytes_read=30581 bytes_retransmit=9 bytes_invalid=0 send_seq=517 receive_seq=517 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004801 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.51 cputime=14.609 memavail=3615796 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=107.5 pwm=0.000
Stats 227.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5590 bytes_read=30774 bytes_retransmit=9 bytes_invalid=0 send_seq=518 receive_seq=518 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004838 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.51 cputime=14.633 memavail=3615860 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=107.0 pwm=0.000
Stats 228.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5596 bytes_read=31012 bytes_retransmit=9 bytes_invalid=0 send_seq=519 receive_seq=519 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004763 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.51 cputime=14.661 memavail=3615928 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=106.5 pwm=0.000
Stats 229.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5602 bytes_read=31219 bytes_retransmit=9 bytes_invalid=0 send_seq=520 receive_seq=520 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004866 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.51 cputime=14.696 memavail=3615864 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=105.7 pwm=0.000
Stats 230.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5608 bytes_read=31426 bytes_retransmit=9 bytes_invalid=0 send_seq=521 receive_seq=521 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004787 heater_bed: target=0 temp=22.1 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.47 cputime=14.719 memavail=3615956 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=105.1 pwm=0.000
Stats 231.9: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5614 bytes_read=31664 bytes_retransmit=9 bytes_invalid=0 send_seq=522 receive_seq=522 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=180004827 heater_bed: target=0 temp=22.0 pwm=0.000 z_thermal_adjust: temp=21.9 chamber_heater: target=0 temp=22.0 pwm=0.000 sysload=1.47 cputime=14.752 memavail=3615956 print_time=0.000 buffer_time=0.000 print_stall=0 extruder: target=0 temp=104.9 pwm=0.000