Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/tmp/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-531-g3796a319'
CPU: 4 core ARMv7 Processor rev 3 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Thu Jul 28 17:15:38 2022 (1659024939.0 26.2)
===== Config file =====
[virtual_sdcard]
path = ~/gcode_files

[display_status]

[pause_resume]

[gcode_macro PAUSE]
rename_existing = BASE_PAUSE
gcode = 
	SAVE_GCODE_STATE NAME=PAUSE_state
	BASE_PAUSE
	G91
	G1 E-{E} F2100
	G1 Z{Z}
	G90
	G1 X{X} Y{Y} F6000

[gcode_macro RESUME]
rename_existing = BASE_RESUME
gcode = 
	G91
	G1 E{E} F2100
	G90
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
	BASE_RESUME

[gcode_macro CANCEL_PRINT]
rename_existing = BASE_CANCEL_PRINT
gcode = 
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	SDCARD_RESET_FILE
	BASE_CANCEL_PRINT

[force_move]
enable_force_move = true

[tmc2130 stepper_x]
cs_pin = ar65
interpolate = True
run_current = 0.5
hold_current = 0.5
sense_resistor = 0.110
stealthchop_threshold = 100
driver_sgt = 7
diag1_pin = ^!ar3

[stepper_x]
step_pin = ar54
dir_pin = !ar55
enable_pin = !ar38
microsteps = 16
rotation_distance = 40
endstop_pin = tmc2130_stepper_x:virtual_endstop
position_endstop = 0
position_max = 220
homing_speed = 50
homing_retract_dist = 5.0

[tmc2130 stepper_y]
cs_pin = ar66
interpolate = True
run_current = 0.5
hold_current = 0.5
sense_resistor = 0.110
stealthchop_threshold = 100
driver_sgt = 8
diag1_pin = ^!ar14

[stepper_y]
step_pin = ar60
dir_pin = !ar61
enable_pin = !ar56
microsteps = 16
rotation_distance = 40
endstop_pin = tmc2130_stepper_y:virtual_endstop
position_endstop = 0
position_max = 220
homing_speed = 50
homing_retract_dist = 5.0

[tmc2130 stepper_z]
cs_pin = ar44
interpolate = True
run_current = 1.0
hold_current = 0.80
sense_resistor = 0.110

[stepper_z]
step_pin = ar46
dir_pin = !ar48
enable_pin = !ar62
microsteps = 16
rotation_distance = 1.472
endstop_pin = probe:z_virtual_endstop
position_max = 300
position_min = -2

[tmc2130 extruder]
cs_pin = ar42
interpolate = false
run_current = 0.7
hold_current = 0.25
sense_resistor = 0.110
stealthchop_threshold = 300

[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
microsteps = 32
rotation_distance = 7.3816116864
nozzle_diameter = 0.400
filament_diameter = 1.7500
max_extrude_only_distance = 150.0
pressure_advance = 0.48
heater_pin = ar10
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_temp = 0
max_temp = 300
control = pid
pid_kp = 29.558
pid_ki = 1.438
pid_kd = 151.852

[bltouch]
sensor_pin = ^ar18
control_pin = ar63
samples = 2
samples_result = median
samples_tolerance = 0.050
samples_tolerance_retries = 3
x_offset = 27
y_offset = 4
z_offset = 0.800

[bed_mesh]
mesh_min = 45,25
mesh_max = 210,210
probe_count = 5,5
fade_start = 1.0
fade_end = 10.0

[safe_z_home]
home_xy_position = 110,110
speed = 50
z_hop = 10
z_hop_speed = 5

[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
min_temp = 0
max_temp = 110
control = pid
pid_kp = 67.971
pid_ki = 1.349
pid_kd = 856.437

[fan]
pin = ar6

[heater_fan my_nozzle_fan]
pin = ar9
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[controller_fan my_controller_fan]
pin = ar11
heater = heater_bed
fan_speed = 1.0

[temperature_sensor raspberry_pi]
sensor_type = temperature_host
min_temp = 0
max_temp = 100

[ds18b20 Chamber]
sensor_type = DS18B20
serial_no = 28-020e9177e866
ds18_report_time = 1.0
sensor_mcu = host

[mcu]
serial = /dev/ttyUSB0

[board_pins arduino-mega]
mcu = mcu
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[mcu host]
serial = /tmp/klipper_host_mcu

[printer]
kinematics = corexy
max_velocity = 500
max_accel = 1000
max_z_velocity = 5
max_z_accel = 5

[adxl345]
cs_pin = host:None

[resonance_tester]
accel_chip = adxl345
probe_points = 
	100,100,20

[input_shaper]
shaper_freq_x = 68.4
shaper_type_x = mzv
shaper_freq_y = 53.2
shaper_type_y = mzv

[bed_mesh default]
version = 1
points = 
	-0.919540, -0.637560, -0.373060, -0.133860, 0.150190
	-0.729330, -0.457010, -0.197110, 0.093380, 0.398130
	-0.579370, -0.282670, -0.012420, 0.266800, 0.537050
	-0.416070, -0.106030, 0.161230, 0.382260, 0.607430
	-0.290030, 0.022310, 0.209990, 0.432400, 0.624220
tension = 0.2
min_x = 45.0
algo = lagrange
y_count = 5
mesh_y_pps = 2
min_y = 25.0
x_count = 5
max_y = 210.0
mesh_x_pps = 2
max_x = 210.0

[probe]
z_offset = 0.020

[bed_mesh 30.21.2021]
version = 1
points = 
	-0.629740, -0.469660, -0.314640, -0.150880, 0.015640
	-0.542340, -0.351900, -0.161460, 0.036340, 0.244720
	-0.389160, -0.180780, 0.009660, 0.186760, 0.360640
	-0.252080, -0.024840, 0.145820, 0.289340, 0.431020
	-0.120980, 0.094300, 0.239200, 0.375360, 0.464140
tension = 0.2
mesh_x_pps = 2
algo = lagrange
min_x = 30.0
min_y = 30.0
y_count = 5
mesh_y_pps = 2
x_count = 5
max_x = 185.0
max_y = 185.0

[bed_mesh 30.12.2021]
version = 1
points = 
	-0.918620, -0.675280, -0.451260, -0.248400, 0.009660
	-0.739680, -0.490820, -0.252540, 0.002760, 0.248400
	-0.567180, -0.296240, -0.043700, 0.155020, 0.386400
	-0.406180, -0.106260, 0.120060, 0.307280, 0.506000
	-0.275540, -0.001380, 0.147200, 0.372140, 0.532220
tension = 0.2
min_x = 45.0
algo = lagrange
y_count = 5
mesh_y_pps = 2
min_y = 25.0
x_count = 5
max_y = 210.0
mesh_x_pps = 2
max_x = 210.0

[bed_mesh 31.12.2021]
version = 1
points = 
	-0.919540, -0.637560, -0.373060, -0.133860, 0.150190
	-0.729330, -0.457010, -0.197110, 0.093380, 0.398130
	-0.579370, -0.282670, -0.012420, 0.266800, 0.537050
	-0.416070, -0.106030, 0.161230, 0.382260, 0.607430
	-0.290030, 0.022310, 0.209990, 0.432400, 0.624220
tension = 0.2
min_x = 45.0
algo = lagrange
y_count = 5
mesh_y_pps = 2
min_y = 25.0
x_count = 5
max_y = 210.0
mesh_x_pps = 2
max_x = 210.0
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 175, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 296, in check_unused_options
    % (section,))
Error: Section 'ds18b20 chamber' is not a valid config section
webhooks client 3042086264: New connection
webhooks client 3042086264: Client info {'program': 'Moonraker', 'version': 'v0.7.1-612-g5d4db16'}