Loaded MCU 'can0' 107 commands (v0.11.0-40-gaac613bf / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-11+rpi1+11) 2.31.1)
MCU 'can0' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CANBUS_FREQUENCY=250000 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RECEIVE_WINDOW=192 RESERVE_PINS_CAN=PB0,PB1 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'can0' (1024 moves)
===== Config file =====
[stepper_x]
step_pin = PF13
dir_pin = PF12
enable_pin = !PF14
microsteps = 32
rotation_distance = 32
endstop_pin = tmc2209_stepper_x:virtual_endstop
position_endstop = 0
position_max = 320
homing_speed = 50
homing_retract_dist = 0

[tmc2209 stepper_x]
uart_pin = PC4
diag_pin = ^PG6
run_current = 0.800
stealthchop_threshold = 999999
driver_sgthrs = 140
interpolate = True

[stepper_y]
step_pin = PG0
dir_pin = PG1
enable_pin = !PF15
microsteps = 32
rotation_distance = 32
endstop_pin = tmc2209_stepper_y:virtual_endstop
position_endstop = 0
position_max = 300
position_min = -30
homing_speed = 50
homing_retract_dist = 0

[tmc2209 stepper_y]
uart_pin = PD11
diag_pin = ^PG9
run_current = 0.800
stealthchop_threshold = 999999
driver_sgthrs = 150
interpolate = True

[stepper_z]
step_pin = PF11
dir_pin = PG3
enable_pin = !PG5
microsteps = 32
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_max = 250

[tmc2209 stepper_z]
uart_pin = PC6
diag_pin = ^PG10
run_current = 0.350
stealthchop_threshold = 999999
interpolate = True

[stepper_z1]
step_pin = PG4
dir_pin = PC1
enable_pin = !PA0
microsteps = 32
rotation_distance = 8

[tmc2209 stepper_z1]
uart_pin = PC7
diag_pin = ^PG11
run_current = 0.350
stealthchop_threshold = 999999
interpolate = True

[extruder]
step_pin = can0:EXT_STEP
dir_pin = !can0:EXT_DIR
enable_pin = !can0:EXT_EN
microsteps = 32
gear_ratio = 50:17
rotation_distance = 24.389
max_extrude_only_distance = 1400.0
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
max_extrude_cross_section = 10.5
nozzle_diameter = 0.600
filament_diameter = 1.750
heater_pin = can0:HE0
sensor_pin = can0:TH0
sensor_type = EPCOS 100K B57560G104F
min_temp = 0
max_temp = 250
pressure_advance = 0.03
control = pid
pid_kp = 29.366
pid_ki = 2.797
pid_kd = 77.087

[tmc2209 extruder]
uart_pin = can0:EXT_UART
run_current = 0.400
stealthchop_threshold = 999999
interpolate = True

[servo brush_servo]
pin = PB0
minimum_pulse_width = 0.00115
maximum_pulse_width = 0.0022
maximum_servo_angle = 180
initial_angle = 0

[heater_bed]
heater_pin = PA1
sensor_type = EPCOS 100K B57560G104F
sensor_pin = PF3
min_temp = 0
max_temp = 130
control = pid
pid_kp = 41.828
pid_ki = 0.965
pid_kd = 453.308

[fan]
pin = can0:FAN1
kick_start_time = 0.25
cycle_time = 0.15
off_below = 0.10

[heater_fan hotend_fan]
pin = can0:FAN0
max_power = 1.0
kick_start_time = 0.5
heater = extruder
heater_temp = 50.0

[bltouch]
sensor_pin = ^can0:PROBE_2
control_pin = can0:PROBE_1
stow_on_each_sample = False
probe_with_touch_mode = True
x_offset = -30
y_offset = 1
z_offset = 1.60

[z_tilt]
z_positions = 
	-50, 150
	366,150
points = 
	30,150
	290,150
speed = 120
retries = 10
retry_tolerance = 0.005

[board_pins]
aliases = 
	
	EXP1_1=PE8, EXP1_2=PE7,
	EXP1_3=PE9, EXP1_4=PE10,
	EXP1_5=PE12, EXP1_6=PE13,
	EXP1_7=PE14, EXP1_8=PE15,
	EXP1_9=<GND>, EXP1_10=<5V>,
	
	
	EXP2_1=PA6, EXP2_2=PA5,
	EXP2_3=PB1, EXP2_4=PA4,
	EXP2_5=PB2, EXP2_6=PA7,
	EXP2_7=PC15, EXP2_8=<RST>,
	EXP2_9=<GND>, EXP2_10=<5V>

[mcu]
canbus_uuid = ff6a19f0a6d2

[temperature_sensor OCTOPUS]
sensor_type = temperature_mcu

[board_pins EBB36_G0B1_v1.2]
mcu = can0
aliases = 
aliases_step = 
	EXT_EN=PD2,EXT_STEP=PD0,EXT_DIR=PD1,EXT_UART=PA15
aliases_limitsw = 
	LIMIT_1=PB7,LIMIT_2=PB5,LIMIT_3=PB6
aliases_bltouch = 
	PROBE_1=PB9,PROBE_2=PB8
aliases_fans = 
	FAN0=PA1,FAN1=PA0
aliases_thermistors = 
	TH0=PA3,PT100_CS=PA4,PT100_SCLK=PA5,PT100_MISO=PA6,PT100_MOSI=PA7
aliases_heaters = 
	HE0=PB13
aliases_rgb = 
	RGBLED=PD3
aliases_adxl = 
	ADXL_CS=PB12,ADXL_SCLK=PB10,ADXL_MISO=PB2,ADXL_MOSI=PB11
aliases_i2c = 
	AUX0=PB3,AUX1=PB4

[mcu can0]
canbus_uuid = bcb4a8b6c98f

[temperature_sensor EBB42]
sensor_type = temperature_mcu
sensor_mcu = can0

[adxl345]
cs_pin = can0:ADXL_CS
spi_software_sclk_pin = can0:ADXL_SCLK
spi_software_mosi_pin = can0:ADXL_MOSI
spi_software_miso_pin = can0:ADXL_MISO
axes_map = y,z,x

[resonance_tester]
accel_chip = adxl345
probe_points = 
	150,150,20

[neopixel lightbar]
pin = PB6
chain_count = 45
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 1.0
initial_white = 0.0

[gcode_macro LED_OFF]
gcode = 
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=0 WHITE=0

[gcode_macro LED_ON]
gcode = 
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=0 WHITE=1

[gcode_macro POWER_OFF_PRINTER]
gcode = 
	{action_call_remote_method("set_device_power",
	device="printer",
	state="off")}

[delayed_gcode POWER_OFF_PRINTER_CHECK]
gcode = 
	{% if printer.idle_timeout.state == "Idle" or printer.idle_timeout.state == "Ready" %}
	{% if printer.extruder.temperature < 50.0 and printer.heater_bed.temperature < 50.0 %}
	{% if printer.extruder.target == 0.0 and printer.heater_bed.target == 0.0 %}
	UPDATE_DELAYED_GCODE ID=POWER_OFF_PRINTER_CHECK DURATION=0
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=0 WHITE=0
	POWER_OFF_PRINTER
	{% else %}
	UPDATE_DELAYED_GCODE ID=POWER_OFF_PRINTER_CHECK DURATION=2
	{% endif %}
	{% else %}
	{% if printer.idle_timeout.state == "Printing" %}
	UPDATE_DELAYED_GCODE ID=POWER_OFF_PRINTER_CHECK DURATION=0
	{% else %}
	{% if printer.extruder.target == 0.0 and printer.heater_bed.target == 0.0 %}
	UPDATE_DELAYED_GCODE ID=POWER_OFF_PRINTER_CHECK DURATION=2
	{% else %}
	UPDATE_DELAYED_GCODE ID=POWER_OFF_PRINTER_CHECK DURATION=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[homing_override]
axes = z
set_position_z = 0
gcode = 
	{% set user = printer['gcode_macro _USER_VARIABLE'] %}
	{% set home_x, home_y, home_z = False, False, False %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set home_x, home_y, home_z = True, True, True %}
	{% else %}
	{% if params.X is defined %}{% set home_x = True %}{% endif %}
	{% if params.Y is defined %}{% set home_y = True %}{% endif %}
	{% if params.Z is defined %}
	{% if 'x' not in printer.toolhead.homed_axes %}{% set home_x = True %}{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}{% set home_y = True %}{% endif %}
	{% set home_z = True %}
	{% endif %}
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL=800 ACCEL_TO_DECEL=400
	G0 Z10 F1500
	{% if home_x %} SENSORLESS_HOME_X   {% endif %}
	{% if home_y %} SENSORLESS_HOME_Y   {% endif %}
	{% if home_z %} HOME_Z              {% endif %}
	SET_VELOCITY_LIMIT ACCEL=2600 ACCEL_TO_DECEL=1300

[gcode_macro SENSORLESS_HOME_X]
gcode = 
	{% set HOME_CUR = 0.700 %}
	{% set driver_config = printer.configfile.settings['tmc2209 stepper_x'] %}
	{% set RUN_CUR = driver_config.run_current %}
	
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR}
	
	G4 P500
	
	G28 X0
	
	G90
	G1 X5 F1200
	
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR}

[gcode_macro SENSORLESS_HOME_Y]
gcode = 
	{% set HOME_CUR = 0.700 %}
	{% set driver_config = printer.configfile.settings['tmc2209 stepper_y'] %}
	{% set RUN_CUR = driver_config.run_current %}
	
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR}
	
	G4 P500
	
	G28 Y0
	
	G90
	G1 Y5 F1200
	
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CUR}

[gcode_macro HOME_Z]
gcode = 
	G0 X150 Y150 F6000
	G28 Z0
	G0 Z10 F500

[gcode_macro NEOPIXEL_DISPLAY]
gcode = 
	{% set led = params.LED %}
	{% set type = params.TYPE %}
	{% set mode = params.MODE %}
	{% set my_neopixel = printer.configfile.config['neopixel ' ~ led] %}
	
	{% if mode == 'progress' %}
	{% for i in range(my_neopixel.chain_count|int) %}
	SET_LED_TEMPLATE LED={led} INDEX={i+1} TEMPLATE={'led_' ~ type ~ '_' ~ mode} param_led_num={i+1} param_led_total={my_neopixel.chain_count|int}
	{% endfor %}
	{% endif %}
	{% if mode == 'glow' %}
	SET_LED_TEMPLATE LED={led} TEMPLATE={'led_' ~ type ~ '_' ~ mode}
	{% endif %}

[display_template led_extruder_temp_glow]
text = 
	{% if printer.extruder.target > 0.0 %}
	{%  set temp = printer.extruder.target %}
	{% else %}
	{% set temp = printer.configfile.config.extruder.max_temp %}
	{% endif %}
	{% set ratio = printer.extruder.temperature / temp|float %}
	{ratio}, 0.0, {1-ratio}, 0.0

[display_template led_extruder_temp_progress]
param_led_num = 0
param_led_total = 1
text = 
	{% if printer.extruder.target > 0.0 %}
	{%  set temp = printer.extruder.target %}
	{% else %}
	{% set temp = printer.configfile.config.extruder.max_temp %}
	{% endif %}
	{% set ratio = printer.extruder.temperature / temp|float %}
	{% set led_ratio = param_led_num|float / param_led_total %}
	{% if ratio > led_ratio %}
	{led_ratio}, 0.0, 0.0, 0.0
	{% else %}
	0.0, 0.0, 0.0, 0.0
	{% endif %}

[display_template led_bed_temp_glow]
text = 
	{% if printer.heater_bed.target > 0.0 %}
	{%  set temp = printer.heater_bed.target %}
	{% else %}
	{% set temp = printer.configfile.config.heater_bed.max_temp %}
	{% endif %}
	{% set ratio = printer.heater_bed.temperature / temp|float %}
	{ratio}, 0.0, {1-ratio}, 0.0

[display_template led_bed_temp_progress]
param_led_num = 0
param_led_total = 1
text = 
	{% if printer.heater_bed.target > 0.0 %}
	{%  set temp = printer.heater_bed.target %}
	{% else %}
	{% set temp = printer.configfile.config.heater_bed.max_temp %}
	{% endif %}
	{% set ratio = printer.heater_bed.temperature / temp|float %}
	{% set led_ratio = param_led_num|float / param_led_total %}
	{% if ratio > led_ratio %}
	{led_ratio}, 0.0, 0.0, 0.0
	{% else %}
	0.0, 0.0, 0.0, 0.0
	{% endif %}

[display_template led_print_percent_glow]
text = 
	{% set ratio = printer.virtual_sdcard.progress %}
	0.0, {ratio}, 0.0, 0.0

[display_template led_print_percent_progress]
param_led_num = 0
param_led_total = 1
text = 
	{% set ratio = printer.virtual_sdcard.progress %}
	{% set led_ratio   = param_led_num|float / param_led_total %}
	{% if ratio > led_ratio %}
	0.0, {led_ratio}, 0.0, 0.0
	{% else %}
	0.0, 0.0, 0.0, 0.0
	{% endif %}

[display_template led_printer_speed_glow]
text = 
	{% set ratio  = printer.motion_report.live_velocity|float /  printer.configfile.config.printer.max_velocity|float %}
	0.0, {ratio}, 0.0, 0.0

[display_template led_printer_speed_progress]
param_led_num = 0
param_led_total = 1
text = 
	{% set ratio  = printer.motion_report.live_velocity|float /  printer.configfile.config.printer.max_velocity|float %}
	{% set led_ratio    = param_led_num|float / param_led_total %}
	{% if ratio > led_ratio %}
	0.0, {led_ratio}, 0.0, 0.0
	{% else %}
	0.0, 0.0, 0.0, 0.0
	{% endif %}

[gcode_macro CLEAN_NOZZLE]
gcode = 
	SAVE_GCODE_STATE NAME=clean_nozzle_state
	G90
	G0 Z30 F5000
	SET_SERVO SERVO=brush_servo ANGLE=180
	G4 P500
	G0 X240 Y5 F6000
	{% for wipe in range(8) %}
	{% for coordinate in [(270,-5),(315,-5)] %}
	G0 X{coordinate[0]} Y{coordinate[1] + 0.5 * wipe} Z30 F6000
	{% endfor %}
	{% endfor %}
	SET_SERVO SERVO=brush_servo ANGLE=0
	G4 P500
	G0 X120 Y0 Z2 F5000
	RESTORE_GCODE_STATE NAME=clean_nozzle_state

[gcode_macro START_PRINT]
gcode = 
	
	{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
	{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(200)|float %}
	
	
	{% set NOZZLE = printer.extruder.nozzle_diameter|default(0.4)|float %}
	{% set FILADIA = printer.extruder.filament_diameter|default(1.75)|float %}
	
	
	{% set X_START = 200.0|default(200.0)|float %}
	{% set Y_START = 0.0|default(20.0)|float %}
	
	
	{% set PRIMER_WIDTH = 0.75 * NOZZLE %}
	{% set PRIMER_HEIGHT = 0.70 * NOZZLE %}
	
	
	{% if printer.heater_bed.temperature < BED_TEMP|float-10.0 %}
	NEOPIXEL_DISPLAY LED="lightbar" TYPE=bed_temp MODE=progress
	M190 S{BED_TEMP-10.0}
	{% endif %}
	M140 S{BED_TEMP}
	
	
	NEOPIXEL_DISPLAY LED="lightbar" TYPE=extruder_temp MODE=progress
	M104 S{EXTRUDER_TEMP} T0
	
	
	G28
	
	
	M109 S{EXTRUDER_TEMP} T0
	
	
	CLEAN_NOZZLE
	SET_LED_TEMPLATE LED="lightbar" TEMPLATE=
	SET_LED LED="lightbar" RED=0 GREEN=1 BLUE=0 WHITE=0
	
	
	G92 E0
	G1 X{X_START} Y{Y_START} Z{PRIMER_HEIGHT} F6000.0
	
	G1 X{X_START-100} Y{Y_START} Z{PRIMER_HEIGHT} E15 F2000.0
	G1 X{X_START-100} Y{Y_START + PRIMER_WIDTH} Z{PRIMER_HEIGHT}
	G1 X{X_START} Y{Y_START + PRIMER_WIDTH} Z{PRIMER_HEIGHT} E15 F2000.0
	
	
	G92 E0
	
	G1 Z0.2 F600
	
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=0 WHITE=1.0

[gcode_macro END_PRINT]
gcode = 
	
	{% set X_MAX = printer.toolhead.axis_maximum.x|default(300)|float %}
	{% set Y_MAX = printer.toolhead.axis_maximum.y|default(300)|float %}
	SET_LED LED="lightbar" RED=0 GREEN=1 BLUE=0 WHITE=0
	
	G91
	G1 E-2 F2700
	G1 E-1.5 Z0.2 F2400
	G1 X5 Y5 F6000
	G1 Z10
	G90
	
	
	G1 Z{printer.toolhead.position.z + 10} F600
	G1 X{X_MAX / 2} Y{Y_MAX - 20} F6000
	M106 S0
	M104 S0
	M140 S0
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=1 WHITE=0
	
	
	
	M84 X Y Z E
	
	
	UPDATE_DELAYED_GCODE ID=POWER_OFF_PRINTER_CHECK DURATION=30

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	SET_LED LED="lightbar" RED=1 GREEN=1 BLUE=0 WHITE=0
	PAUSE_BASE
	_TOOLHEAD_PARK_PAUSE_CANCEL

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	
	{% set extrude = printer['gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL'].extrude %}
	
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	
	{% if printer.extruder.can_extrude|lower == 'true' %}
	M83
	G1 E{extrude} F2100
	{% if printer.gcode_move.absolute_extrude |lower == 'true' %} M82 {% endif %}
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=0 WHITE=1.0
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
variable_park = True
gcode = 
	
	{% if printer.pause_resume.is_paused|lower == 'false' and park|lower == 'true'%}
	_TOOLHEAD_PARK_PAUSE_CANCEL
	{% endif %}
	TURN_OFF_HEATERS
	SET_LED LED="lightbar" RED=0 GREEN=0 BLUE=1.0 WHITE=0
	CANCEL_PRINT_BASE

[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL]
description = Helper: park toolhead used in PAUSE and CANCEL_PRINT
variable_extrude = 1.0
gcode = 
	
	
	{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
	{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
	{% set z_park_delta = 2.0 %}
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% if act_z < (max_z - z_park_delta) %}
	{% set z_safe = z_park_delta %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	
	{% if printer.extruder.can_extrude|lower == 'true' %}
	M83
	G1 E-{extrude} F2100
	{% if printer.gcode_move.absolute_extrude |lower == 'true' %} M82 {% endif %}
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F900
	G90
	G1 X{x_park} Y{y_park} F6000
	{% if printer.gcode_move.absolute_coordinates|lower == 'false' %} G91 {% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[force_move]
enable_force_move = True

[printer]
kinematics = corexy
max_velocity = 200
max_accel = 2600
max_z_velocity = 50
max_z_accel = 100

[bed_mesh]
speed = 120
horizontal_move_z = 5
mesh_min = 35, 6
mesh_max = 240, 240
probe_count = 5, 3

[virtual_sdcard]
path = /home/pi/gcode_files

[input_shaper]
shaper_type_x = 2hump_ei
shaper_freq_x = 78.8
shaper_type_y = mzv
shaper_freq_y = 48.2

[display_status]

[pause_resume]

[gcode_arcs]

[bed_mesh COLD_BED]
version = 1
points = 
	-0.050109, -0.052609, -0.063859, -0.045109, 0.014891
	0.077391, 0.031141, 0.007391, 0.021141, 0.066141
	0.044891, -0.023859, -0.051359, -0.042609, 0.008641
x_count = 5
y_count = 3
mesh_x_pps = 2
mesh_y_pps = 2
algo = lagrange
tension = 0.2
min_x = 35.0
max_x = 240.0
min_y = 6.0
max_y = 240.0

[bed_mesh HOT_BED]
version = 1
points = 
	-0.057609, -0.088859, -0.080109, -0.068859, 0.004891
	0.026141, -0.040109, -0.058859, -0.046359, 0.023641
	-0.013859, -0.096359, -0.120109, -0.106359, -0.068859
x_count = 5
y_count = 3
mesh_x_pps = 2
mesh_y_pps = 2
algo = lagrange
tension = 0.2
min_x = 35.0
max_x = 240.0
min_y = 6.0
max_y = 240.0
=======================
Loaded MCU 'mcu' 107 commands (v0.11.0-40-gaac613bf / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-11+rpi1+11) 2.31.1)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1a=PB8,PB9 BUS_PINS_i2c2=PB10,PB11 BUS_PINS_i2c3=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 CANBUS_BRIDGE=1 CLOCK_FREQ=180000000 MCU=stm32f446xx PWM_MAX=255 RECEIVE_WINDOW=192 RESERVE_PINS_CAN=PD0,PD1 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'mcu' (1024 moves)
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.11.0-41-g9b60daf6'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '3.7.3 (default, Jan 22 2021, 20:04:44) \n[GCC 8.3.0]'
webhooks client 1972295312: {'program': 'Moonraker', 'version': 'v0.7.1-790-g358aee9'}
=============== Log rollover at Fri Dec 30 06:12:31 2022 ===============
Timeout with MCU 'can0' (eventtime=89525.721903)
Transition to shutdown state: Lost communication with MCU 'can0'
Dumping gcode input 0 blocks
Dumping 20 requests for client 1972295312
Received 72033.410112: b'{"id": 1715171024, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 75633.464257: b'{"id": 1715167920, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 79233.537102: b'{"id": 1715168784, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 85372.710011: b'{"id": 1745302576, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 85372.845424: b'{"id": 1735591856, "method": "info", "params": {}}'
Received 85372.847103: b'{"id": 1735591184, "method": "objects/list", "params": {}}'
Received 85372.848500: b'{"id": 1735591376, "method": "gcode/help", "params": {}}'
Received 85372.966010: b'{"id": 1715170480, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "temperature_sensor OCTOPUS": null, "temperature_sensor EBB42": null, "extruder": null, "bed_mesh": null, "configfile": null, "display_status": null, "fan": null, "gcode_move": null, "idle_timeout": null, "pause_resume": null, "toolhead": null, "virtual_sdcard": null, "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "motion_report": null, "exclude_object": ["current_object", "objects", "excluded_objects"], "heater_fan hotend_fan": null, "mcu": null, "mcu can0": null, "tmc2209 stepper_x": null, "tmc2209 stepper_y": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 extruder": null, "servo brush_servo": null, "heaters": null, "probe": null, "z_tilt": null, "neopixel lightbar": null, "gcode_macro LED_OFF": null, "gcode_macro LED_ON": null, "gcode_macro POWER_OFF_PRINTER": null, "gcode_macro SENSORLESS_HOME_X": null, "gcode_macro SENSORLESS_HOME_Y": null, "gcode_macro HOME_Z": null, "gcode_macro NEOPIXEL_DISPLAY": null, "gcode_macro CLEAN_NOZZLE": null, "gcode_macro START_PRINT": null, "gcode_macro END_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "query_endstops": null, "system_stats": null, "manual_probe": null}, "response_template": {"method": "process_status_update"}}}'
Received 85398.325232: b'{"id": 1745197232, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89279.327118: b'{"id": 1744659824, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89279.469510: b'{"id": 1745047696, "method": "info", "params": {}}'
Received 89279.470694: b'{"id": 1745178672, "method": "objects/list", "params": {}}'
Received 89279.470694: b'{"id": 1745180432, "method": "gcode/help", "params": {}}'
Received 89280.140920: b'{"id": 1745365264, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "temperature_sensor OCTOPUS": null, "temperature_sensor EBB42": null, "extruder": null, "bed_mesh": null, "configfile": null, "display_status": null, "fan": null, "gcode_move": null, "idle_timeout": null, "pause_resume": null, "toolhead": null, "virtual_sdcard": null, "firmware_retraction": ["retract_length", "retract_speed", "unretract_extra_length", "unretract_speed"], "motion_report": null, "exclude_object": ["current_object", "objects", "excluded_objects"], "heater_fan hotend_fan": null, "mcu": null, "mcu can0": null, "tmc2209 stepper_x": null, "tmc2209 stepper_y": null, "tmc2209 stepper_z": null, "tmc2209 stepper_z1": null, "tmc2209 extruder": null, "servo brush_servo": null, "heaters": null, "probe": null, "z_tilt": null, "neopixel lightbar": null, "gcode_macro LED_OFF": null, "gcode_macro LED_ON": null, "gcode_macro POWER_OFF_PRINTER": null, "gcode_macro SENSORLESS_HOME_X": null, "gcode_macro SENSORLESS_HOME_Y": null, "gcode_macro HOME_Z": null, "gcode_macro NEOPIXEL_DISPLAY": null, "gcode_macro CLEAN_NOZZLE": null, "gcode_macro START_PRINT": null, "gcode_macro END_PRINT": null, "gcode_macro PAUSE": null, "gcode_macro RESUME": null, "gcode_macro CANCEL_PRINT": null, "gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL": null, "query_endstops": null, "system_stats": null, "manual_probe": null}, "response_template": {"method": "process_status_update"}}}'
Received 89297.436531: b'{"id": 1745298192, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89303.031131: b'{"id": 1745096656, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89306.186035: b'{"id": 1745096208, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89307.492136: b'{"id": 1735589936, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89337.657810: b'{"id": 1714772240, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
Received 89340.248034: b'{"id": 1714770352, "method": "objects/query", "params": {"objects": {"print_stats": null}}}'
gcode state: absolute_coord=True absolute_extrude=True base_position=[0.0, 0.0, 0.0, 0.0] last_position=[0.0, 0.0, 0.0, 0.0] homing_position=[0.0, 0.0, 0.0, 0.0] speed_factor=0.016666666666666666 extrude_factor=1.0 speed=25.0
Reactor garbage collection: (46111.340301264, 0.0, 0.0)
MCU 'mcu' shutdown: Command request
clocksync state: mcu_freq=180000000 last_clock=14246372476818 clock_est=(89496.501 14241225446780 180000730.893) min_half_rtt=0.000285 min_rtt_time=89216.853 time_avg=89496.501(849.915) clock_avg=14241225446780.943(152985265935.620) pred_variance=37278127.028
Dumping serial stats: bytes_write=484864 bytes_read=9123903 bytes_retransmit=7 bytes_invalid=38 send_seq=80585 receive_seq=80585 retransmit_seq=80482 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0
Dumping send queue 100 messages
Sent 0 89428.587920 89428.587920 6: seq: 15, get_clock
Sent 1 89429.573108 89429.573108 6: seq: 16, get_clock
Sent 2 89430.557863 89430.557863 6: seq: 17, get_clock
Sent 3 89431.543093 89431.543093 6: seq: 18, get_clock
Sent 4 89432.527668 89432.527668 6: seq: 19, get_clock
Sent 5 89433.512747 89433.512747 6: seq: 1a, get_clock
Sent 6 89434.497260 89434.497260 6: seq: 1b, get_clock
Sent 7 89435.482166 89435.482166 6: seq: 1c, get_clock
Sent 8 89436.466665 89436.466665 6: seq: 1d, get_clock
Sent 9 89437.451113 89437.451113 6: seq: 1e, get_clock
Sent 10 89438.435308 89438.435308 6: seq: 1f, get_clock
Sent 11 89439.419772 89439.419772 6: seq: 10, get_clock
Sent 12 89440.404680 89440.404680 6: seq: 11, get_clock
Sent 13 89441.389927 89441.389927 6: seq: 12, get_clock
Sent 14 89442.374969 89442.374969 6: seq: 13, get_clock
Sent 15 89443.359483 89443.359483 6: seq: 14, get_clock
Sent 16 89444.344220 89444.344220 6: seq: 15, get_clock
Sent 17 89445.329499 89445.329499 6: seq: 16, get_clock
Sent 18 89446.314620 89446.314620 6: seq: 17, get_clock
Sent 19 89447.299049 89447.299049 6: seq: 18, get_clock
Sent 20 89448.284197 89448.284197 6: seq: 19, get_clock
Sent 21 89449.269176 89449.269176 6: seq: 1a, get_clock
Sent 22 89450.253944 89450.253944 6: seq: 1b, get_clock
Sent 23 89451.238523 89451.238523 6: seq: 1c, get_clock
Sent 24 89452.223226 89452.223226 6: seq: 1d, get_clock
Sent 25 89453.207989 89453.207989 6: seq: 1e, get_clock
Sent 26 89454.192834 89454.192834 6: seq: 1f, get_clock
Sent 27 89455.177126 89455.177126 6: seq: 10, get_clock
Sent 28 89456.161284 89456.161284 6: seq: 11, get_clock
Sent 29 89457.145459 89457.145459 6: seq: 12, get_clock
Sent 30 89458.130286 89458.130286 6: seq: 13, get_clock
Sent 31 89459.115265 89459.115265 6: seq: 14, get_clock
Sent 32 89460.099897 89460.099897 6: seq: 15, get_clock
Sent 33 89461.084799 89461.084799 6: seq: 16, get_clock
Sent 34 89462.068964 89462.068964 6: seq: 17, get_clock
Sent 35 89463.053208 89463.053208 6: seq: 18, get_clock
Sent 36 89464.038184 89464.038184 6: seq: 19, get_clock
Sent 37 89465.023392 89465.023392 6: seq: 1a, get_clock
Sent 38 89466.008263 89466.008263 6: seq: 1b, get_clock
Sent 39 89466.992523 89466.992523 6: seq: 1c, get_clock
Sent 40 89467.977360 89467.977360 6: seq: 1d, get_clock
Sent 41 89468.961926 89468.961926 6: seq: 1e, get_clock
Sent 42 89469.946396 89469.946396 6: seq: 1f, get_clock
Sent 43 89470.930967 89470.930967 6: seq: 10, get_clock
Sent 44 89471.915126 89471.915126 6: seq: 11, get_clock
Sent 45 89472.900400 89472.900400 6: seq: 12, get_clock
Sent 46 89473.885124 89473.885124 6: seq: 13, get_clock
Sent 47 89474.869273 89474.869273 6: seq: 14, get_clock
Sent 48 89475.853580 89475.853580 6: seq: 15, get_clock
Sent 49 89476.838471 89476.838471 6: seq: 16, get_clock
Sent 50 89477.823542 89477.823542 6: seq: 17, get_clock
Sent 51 89478.808031 89478.808031 6: seq: 18, get_clock
Sent 52 89479.792963 89479.792963 6: seq: 19, get_clock
Sent 53 89480.777087 89480.777087 6: seq: 1a, get_clock
Sent 54 89481.761539 89481.761539 6: seq: 1b, get_clock
Sent 55 89482.746003 89482.746003 6: seq: 1c, get_clock
Sent 56 89483.730308 89483.730308 6: seq: 1d, get_clock
Sent 57 89484.714971 89484.714971 6: seq: 1e, get_clock
Sent 58 89485.699324 89485.699324 6: seq: 1f, get_clock
Sent 59 89486.683909 89486.683909 6: seq: 10, get_clock
Sent 60 89487.668017 89487.668017 6: seq: 11, get_clock
Sent 61 89488.653002 89488.653002 6: seq: 12, get_clock
Sent 62 89489.637560 89489.637560 6: seq: 13, get_clock
Sent 63 89490.622126 89490.622126 6: seq: 14, get_clock
Sent 64 89491.606420 89491.606420 6: seq: 15, get_clock
Sent 65 89492.590811 89492.590811 6: seq: 16, get_clock
Sent 66 89493.575241 89493.575241 6: seq: 17, get_clock
Sent 67 89494.559880 89494.559880 6: seq: 18, get_clock
Sent 68 89495.544889 89495.544889 6: seq: 19, get_clock
Sent 69 89496.529252 89496.529252 6: seq: 1a, get_clock
Sent 70 89497.514589 89497.514589 6: seq: 1b, get_clock
Sent 71 89498.498838 89498.498838 6: seq: 1c, get_clock
Sent 72 89499.483006 89499.483006 6: seq: 1d, get_clock
Sent 73 89500.467544 89500.467544 6: seq: 1e, get_clock
Sent 74 89501.452395 89501.452395 6: seq: 1f, get_clock
Sent 75 89502.437163 89502.437163 6: seq: 10, get_clock
Sent 76 89503.422135 89503.422135 6: seq: 11, get_clock
Sent 77 89504.406575 89504.406575 6: seq: 12, get_clock
Sent 78 89505.391325 89505.391325 6: seq: 13, get_clock
Sent 79 89506.375729 89506.375729 6: seq: 14, get_clock
Sent 80 89507.360484 89507.360484 6: seq: 15, get_clock
Sent 81 89508.345553 89508.345553 6: seq: 16, get_clock
Sent 82 89509.330425 89509.330425 6: seq: 17, get_clock
Sent 83 89510.314668 89510.314668 6: seq: 18, get_clock
Sent 84 89511.299078 89511.299078 6: seq: 19, get_clock
Sent 85 89512.284227 89512.284227 6: seq: 1a, get_clock
Sent 86 89513.269782 89513.269782 6: seq: 1b, get_clock
Sent 87 89514.255165 89514.255165 6: seq: 1c, get_clock
Sent 88 89515.241077 89515.241077 6: seq: 1d, get_clock
Sent 89 89516.225901 89516.225901 6: seq: 1e, get_clock
Sent 90 89517.210819 89517.210819 6: seq: 1f, get_clock
Sent 91 89518.196060 89518.196060 6: seq: 10, get_clock
Sent 92 89519.181743 89519.181743 6: seq: 11, get_clock
Sent 93 89520.168143 89520.168143 6: seq: 12, get_clock
Sent 94 89521.154434 89521.154434 6: seq: 13, get_clock
Sent 95 89522.139979 89522.139979 6: seq: 14, get_clock
Sent 96 89523.125614 89523.125614 6: seq: 15, get_clock
Sent 97 89524.110829 89524.110829 6: seq: 16, get_clock
Sent 98 89525.095563 89525.095563 6: seq: 17, get_clock
Sent 99 89525.730496 89525.730496 6: seq: 18, emergency_stop
Dumping receive queue 100 messages
Receive: 0 89513.240164 89512.284227 15: seq: 1b, analog_in_state oid=15 next_clock=2179446464 value=31345
Receive: 1 89513.260538 89512.284227 14: seq: 1b, analog_in_state oid=17 next_clock=2183046464 value=7578
Receive: 2 89513.271023 89513.269782 11: seq: 1c, clock clock=2132271365
Receive: 3 89513.539653 89513.269782 15: seq: 1c, analog_in_state oid=15 next_clock=2233446464 value=31347
Receive: 4 89513.559912 89513.269782 14: seq: 1c, analog_in_state oid=17 next_clock=2237046464 value=7581
Receive: 5 89513.839531 89513.269782 15: seq: 1c, analog_in_state oid=15 next_clock=2287446464 value=31342
Receive: 6 89513.859991 89513.269782 14: seq: 1c, analog_in_state oid=17 next_clock=2291046464 value=7576
Receive: 7 89514.139533 89513.269782 15: seq: 1c, analog_in_state oid=15 next_clock=2341446464 value=31343
Receive: 8 89514.159780 89513.269782 14: seq: 1c, analog_in_state oid=17 next_clock=2345046464 value=7580
Receive: 9 89514.257282 89514.255165 11: seq: 1d, clock clock=2309648579
Receive: 10 89514.440156 89514.255165 15: seq: 1d, analog_in_state oid=15 next_clock=2395446464 value=31343
Receive: 11 89514.460411 89514.255165 14: seq: 1d, analog_in_state oid=17 next_clock=2399046464 value=7580
Receive: 12 89514.740221 89514.255165 15: seq: 1d, analog_in_state oid=15 next_clock=2449446464 value=31339
Receive: 13 89514.760400 89514.255165 14: seq: 1d, analog_in_state oid=17 next_clock=2453046464 value=7578
Receive: 14 89515.040018 89514.255165 15: seq: 1d, analog_in_state oid=15 next_clock=2503446464 value=31339
Receive: 15 89515.060293 89514.255165 14: seq: 1d, analog_in_state oid=17 next_clock=2507046464 value=7579
Receive: 16 89515.243035 89515.241077 11: seq: 1e, clock clock=2487106881
Receive: 17 89515.339791 89515.241077 15: seq: 1e, analog_in_state oid=15 next_clock=2557446464 value=31336
Receive: 18 89515.360033 89515.241077 14: seq: 1e, analog_in_state oid=17 next_clock=2561046464 value=7581
Receive: 19 89515.639676 89515.241077 15: seq: 1e, analog_in_state oid=15 next_clock=2611446464 value=31336
Receive: 20 89515.659911 89515.241077 14: seq: 1e, analog_in_state oid=17 next_clock=2615046464 value=7580
Receive: 21 89515.939659 89515.241077 15: seq: 1e, analog_in_state oid=15 next_clock=2665446464 value=31334
Receive: 22 89515.959910 89515.241077 14: seq: 1e, analog_in_state oid=17 next_clock=2669046464 value=7579
Receive: 23 89516.227291 89516.225901 11: seq: 1f, clock clock=2664374395
Receive: 24 89516.240330 89516.225901 15: seq: 1f, analog_in_state oid=15 next_clock=2719446464 value=31336
Receive: 25 89516.260549 89516.225901 14: seq: 1f, analog_in_state oid=17 next_clock=2723046464 value=7581
Receive: 26 89516.540291 89516.225901 15: seq: 1f, analog_in_state oid=15 next_clock=2773446464 value=31334
Receive: 27 89516.560535 89516.225901 14: seq: 1f, analog_in_state oid=17 next_clock=2777046464 value=7576
Receive: 28 89516.840164 89516.225901 15: seq: 1f, analog_in_state oid=15 next_clock=2827446464 value=31336
Receive: 29 89516.860411 89516.225901 14: seq: 1f, analog_in_state oid=17 next_clock=2831046464 value=7580
Receive: 30 89517.140195 89516.225901 15: seq: 1f, analog_in_state oid=15 next_clock=2881446464 value=31339
Receive: 31 89517.160406 89516.225901 14: seq: 1f, analog_in_state oid=17 next_clock=2885046464 value=7580
Receive: 32 89517.212679 89517.210819 11: seq: 10, clock clock=2841662788
Receive: 33 89517.439630 89517.210819 15: seq: 10, analog_in_state oid=15 next_clock=2935446464 value=31337
Receive: 34 89517.459788 89517.210819 14: seq: 10, analog_in_state oid=17 next_clock=2939046464 value=7579
Receive: 35 89517.683185 89517.210819 14: seq: 10, stats count=678 sum=443204 sumsq=1495841
Receive: 36 89517.739789 89517.210819 15: seq: 10, analog_in_state oid=15 next_clock=2989446464 value=31335
Receive: 37 89517.760046 89517.210819 14: seq: 10, analog_in_state oid=17 next_clock=2993046464 value=7579
Receive: 38 89518.039692 89517.210819 15: seq: 10, analog_in_state oid=15 next_clock=3043446464 value=31338
Receive: 39 89518.059913 89517.210819 14: seq: 10, analog_in_state oid=17 next_clock=3047046464 value=7583
Receive: 40 89518.197429 89518.196060 11: seq: 11, clock clock=3018998563
Receive: 41 89518.340418 89518.196060 15: seq: 11, analog_in_state oid=15 next_clock=3097446464 value=31339
Receive: 42 89518.360654 89518.196060 14: seq: 11, analog_in_state oid=17 next_clock=3101046464 value=7580
Receive: 43 89518.640289 89518.196060 15: seq: 11, analog_in_state oid=15 next_clock=3151446464 value=31340
Receive: 44 89518.660560 89518.196060 14: seq: 11, analog_in_state oid=17 next_clock=3155046464 value=7582
Receive: 45 89518.940304 89518.196060 15: seq: 11, analog_in_state oid=15 next_clock=3205446464 value=31341
Receive: 46 89518.960661 89518.196060 14: seq: 11, analog_in_state oid=17 next_clock=3209046464 value=7583
Receive: 47 89519.182908 89519.181743 11: seq: 12, clock clock=3196431204
Receive: 48 89519.239724 89519.181743 15: seq: 12, analog_in_state oid=15 next_clock=3259446464 value=31342
Receive: 49 89519.259960 89519.181743 14: seq: 12, analog_in_state oid=17 next_clock=3263046464 value=7581
Receive: 50 89519.539684 89519.181743 15: seq: 12, analog_in_state oid=15 next_clock=3313446464 value=31343
Receive: 51 89519.559911 89519.181743 14: seq: 12, analog_in_state oid=17 next_clock=3317046464 value=7581
Receive: 52 89519.839535 89519.181743 15: seq: 12, analog_in_state oid=15 next_clock=3367446464 value=31350
Receive: 53 89519.859761 89519.181743 14: seq: 12, analog_in_state oid=17 next_clock=3371046464 value=7581
Receive: 54 89520.139526 89519.181743 15: seq: 12, analog_in_state oid=15 next_clock=3421446464 value=31351
Receive: 55 89520.159786 89519.181743 14: seq: 12, analog_in_state oid=17 next_clock=3425046464 value=7581
Receive: 56 89520.170044 89520.168143 11: seq: 13, clock clock=3373981370
Receive: 57 89520.440522 89520.168143 15: seq: 13, analog_in_state oid=15 next_clock=3475446464 value=31350
Receive: 58 89520.460722 89520.168143 14: seq: 13, analog_in_state oid=17 next_clock=3479046464 value=7581
Receive: 59 89520.739965 89520.168143 15: seq: 13, analog_in_state oid=15 next_clock=3529446464 value=31355
Receive: 60 89520.760151 89520.168143 14: seq: 13, analog_in_state oid=17 next_clock=3533046464 value=7578
Receive: 61 89521.040541 89520.168143 15: seq: 13, analog_in_state oid=15 next_clock=3583446464 value=31356
Receive: 62 89521.059522 89520.168143 14: seq: 13, analog_in_state oid=17 next_clock=3587046464 value=7579
Receive: 63 89521.155159 89521.154434 11: seq: 14, clock clock=3551516676
Receive: 64 89521.339642 89521.154434 15: seq: 14, analog_in_state oid=15 next_clock=3637446464 value=31357
Receive: 65 89521.359891 89521.154434 14: seq: 14, analog_in_state oid=17 next_clock=3641046464 value=7582
Receive: 66 89521.640423 89521.154434 15: seq: 14, analog_in_state oid=15 next_clock=3691446464 value=31358
Receive: 67 89521.660656 89521.154434 14: seq: 14, analog_in_state oid=17 next_clock=3695046464 value=7579
Receive: 68 89521.939893 89521.154434 15: seq: 14, analog_in_state oid=15 next_clock=3745446464 value=31356
Receive: 69 89521.960268 89521.154434 14: seq: 14, analog_in_state oid=17 next_clock=3749046464 value=7576
Receive: 70 89522.140816 89522.139979 11: seq: 15, clock clock=3728921567
Receive: 71 89522.239918 89522.139979 15: seq: 15, analog_in_state oid=15 next_clock=3799446464 value=31360
Receive: 72 89522.260163 89522.139979 14: seq: 15, analog_in_state oid=17 next_clock=3803046464 value=7577
Receive: 73 89522.540680 89522.139979 15: seq: 15, analog_in_state oid=15 next_clock=3853446464 value=31364
Receive: 74 89522.559664 89522.139979 14: seq: 15, analog_in_state oid=17 next_clock=3857046464 value=7579
Receive: 75 89522.727531 89522.139979 14: seq: 15, stats count=364 sum=271542 sumsq=1148726
Receive: 76 89522.840544 89522.139979 15: seq: 15, analog_in_state oid=15 next_clock=3907446464 value=31366
Receive: 77 89522.859536 89522.139979 14: seq: 15, analog_in_state oid=17 next_clock=3911046464 value=7579
Receive: 78 89523.126429 89523.125614 11: seq: 16, clock clock=3906330561
Receive: 79 89523.140530 89523.125614 15: seq: 16, analog_in_state oid=15 next_clock=3961446464 value=31363
Receive: 80 89523.159543 89523.125614 14: seq: 16, analog_in_state oid=17 next_clock=3965046464 value=7580
Receive: 81 89523.439897 89523.125614 15: seq: 16, analog_in_state oid=15 next_clock=4015446464 value=31365
Receive: 82 89523.460181 89523.125614 14: seq: 16, analog_in_state oid=17 next_clock=4019046464 value=7581
Receive: 83 89523.740755 89523.125614 15: seq: 16, analog_in_state oid=15 next_clock=4069446464 value=31363
Receive: 84 89523.759646 89523.125614 14: seq: 16, analog_in_state oid=17 next_clock=4073046464 value=7580
Receive: 85 89524.040042 89523.125614 15: seq: 16, analog_in_state oid=15 next_clock=4123446464 value=31366
Receive: 86 89524.060306 89523.125614 14: seq: 16, analog_in_state oid=17 next_clock=4127046464 value=7578
Receive: 87 89524.112032 89524.110829 11: seq: 17, clock clock=4083668443
Receive: 88 89524.340017 89524.110829 15: seq: 17, analog_in_state oid=15 next_clock=4177446464 value=31364
Receive: 89 89524.359515 89524.110829 14: seq: 17, analog_in_state oid=17 next_clock=4181046464 value=7582
Receive: 90 89524.639938 89524.110829 14: seq: 17, analog_in_state oid=15 next_clock=4231446464 value=31364
Receive: 91 89524.660171 89524.110829 13: seq: 17, analog_in_state oid=17 next_clock=4235046464 value=7582
Receive: 92 89524.940642 89524.110829 14: seq: 17, analog_in_state oid=15 next_clock=4285446464 value=31357
Receive: 93 89524.959660 89524.110829 13: seq: 17, analog_in_state oid=17 next_clock=4289046464 value=7580
Receive: 94 89525.096412 89525.095563 10: seq: 18, clock clock=4260923282
Receive: 95 89525.240564 89525.095563 14: seq: 18, analog_in_state oid=15 next_clock=44479168 value=31358
Receive: 96 89525.259538 89525.095563 13: seq: 18, analog_in_state oid=17 next_clock=48079168 value=7576
Receive: 97 89525.539916 89525.095563 14: seq: 18, analog_in_state oid=15 next_clock=98479168 value=31357
Receive: 98 89525.560268 89525.095563 13: seq: 18, analog_in_state oid=17 next_clock=102079168 value=7578
Receive: 99 89525.732202 89525.730496 11: seq: 19, shutdown clock=80246156 static_string_id=Command request