===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-229-g89b4feca'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
=============== Log rollover at Mon Jan 17 00:00:06 2022 ===============
webhooks client 1968797936: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:00:07 2022 (1642377607.9 409.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1971112496: New connection
webhooks client 1971112496: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 00:00:12 2022 (1642377612.6 414.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968479328: New connection
webhooks client 1968479328: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968479328: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:00:14 2022 (1642377614.4 415.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968807528: New connection
webhooks client 1968807528: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 00:18:06 2022 (1642378686.2 1487.8)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1970576440: New connection
webhooks client 1970576440: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970576440: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:18:10 2022 (1642378690.3 1491.8)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1969555216: New connection
webhooks client 1969555216: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1969555216: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:18:52 2022 (1642378732.7 1534.2)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1969554216: New connection
webhooks client 1969554216: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1969554216: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:18:55 2022 (1642378735.4 1536.9)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1970576160: New connection
webhooks client 1970576160: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Transition to shutdown state: Shutdown due to webhooks request
Dumping 20 requests for client 1970576160
Received 1671.642251: {"id": 1729959952, "method": "info", "params": {}}
Received 1673.644385: {"id": 1729960432, "method": "info", "params": {}}
Received 1675.643702: {"id": 1731570128, "method": "info", "params": {}}
Received 1677.642336: {"id": 1731568048, "method": "info", "params": {}}
Received 1679.642319: {"id": 1731569808, "method": "info", "params": {}}
Received 1681.642772: {"id": 1731568496, "method": "info", "params": {}}
Received 1683.642364: {"id": 1731567920, "method": "info", "params": {}}
Received 1685.641602: {"id": 1731568016, "method": "info", "params": {}}
Received 1687.642248: {"id": 1731568016, "method": "info", "params": {}}
Received 1689.643232: {"id": 1740454000, "method": "info", "params": {}}
Received 1691.685452: {"id": 1731569968, "method": "info", "params": {}}
Received 1693.641553: {"id": 1740454768, "method": "info", "params": {}}
Received 1695.643416: {"id": 1731596368, "method": "info", "params": {}}
Received 1697.640009: {"id": 1731597264, "method": "info", "params": {}}
Received 1699.663014: {"id": 1731597936, "method": "info", "params": {}}
Received 1701.651843: {"id": 1731599312, "method": "info", "params": {}}
Received 1703.641332: {"id": 1731598448, "method": "info", "params": {}}
Received 1705.641478: {"id": 1731312240, "method": "info", "params": {}}
Received 1707.642508: {"id": 1731309872, "method": "info", "params": {}}
Received 1709.494073: {"id": 1731309904, "method": "emergency_stop", "params": {}}
Reactor garbage collection: (1687.643816022, 0.0, 0.0)
webhooks client 1970576160: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:21:50 2022 (1642378910.4 1711.9)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971107840: New connection
webhooks client 1971107840: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971107840: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:21:58 2022 (1642378918.4 1720.0)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971672048: New connection
webhooks client 1971672048: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971672048: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:22:02 2022 (1642378922.2 1723.7)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1969839880: New connection
webhooks client 1969839880: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1969839880: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:22:04 2022 (1642378924.8 1726.3)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1970880064: New connection
webhooks client 1970880064: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970880064: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:23:10 2022 (1642378990.4 1791.9)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968871584: New connection
webhooks client 1968871584: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968871584: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:23:20 2022 (1642379000.1 1801.6)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = Sonde : z_virtual_endstop
position_min = -2
position_max = 400

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
proben = 2
sample_result = Durchschnitt
probe_with_touch_mode = wahr
stow_on_each_sample = falsch

[safe_z_home]
home_xy_position = 122.183
geschwindigkeit = 150
z_hop = 10
z_hop_speed = 5

[bett_schrauben]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10

[extruder]
control = pid
pid_kp = 21.465
pid_ki = 0.980
pid_kd = 117.521

[bltouch]
z_offset = 2.045

[heater_bed]
control = pid
pid_kp = 48.362
pid_ki = 0.638
pid_kd = 915.854
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1970873568: New connection
webhooks client 1970873568: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970873568: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:32:18 2022 (1642379538.8 2340.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968520408: New connection
webhooks client 1968520408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1968520408: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:32:21 2022 (1642379541.8 2343.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968504424: New connection
webhooks client 1968504424: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968504424: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:33:36 2022 (1642379616.5 2418.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968566064: New connection
webhooks client 1968566064: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968566064: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:34:36 2022 (1642379676.9 2478.5)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968639192: New connection
webhooks client 1968639192: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968639192: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:34:38 2022 (1642379678.8 2480.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968725848: New connection
webhooks client 1968725848: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Building C code module c_helper.so
Start printer at Mon Jan 17 00:34:57 2022 (1642379697.8 2499.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1971161208: New connection
webhooks client 1971161208: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon Jan 17 00:17:16 2022 (1642378636.0 20.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968709144: New connection
webhooks client 1968709144: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968709144: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:52:17 2022 (1642380737.2 62.2)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1970305784: New connection
webhooks client 1970305784: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970305784: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:54:54 2022 (1642380894.9 219.9)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1971076352: New connection
webhooks client 1971076352: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971076352: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:55:04 2022 (1642380904.2 229.2)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1968593096: New connection
webhooks client 1968593096: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968593096: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:58:57 2022 (1642381137.2 462.3)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1971075152: New connection
webhooks client 1971075152: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971075152: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:59:55 2022 (1642381195.4 520.4)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1970613504: New connection
webhooks client 1970613504: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970613504: Disconnected
Restarting printer
Start printer at Mon Jan 17 00:59:58 2022 (1642381198.2 523.2)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1968979240: New connection
webhooks client 1968979240: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968979240: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:00:41 2022 (1642381241.4 566.4)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1971074832: New connection
webhooks client 1971074832: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971074832: Disconnected
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon Jan 17 01:03:42 2022 (1642381422.1 21.6)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 252, in _parse_config
    visited)
  File "/home/pi/klipper/klippy/configfile.py", line 224, in _resolve_include
    raise error("Include file '%s' does not exist" % (include_glob,))
Error: Include file '/home/pi/klipper_config/mainsail.cgf' does not exist
webhooks client 1971973056: New connection
webhooks client 1971973056: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Include file '/home/pi/klipper_config/mainsail.cgf' does not exist

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.
Printer is halted

webhooks client 1971973056: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:05:15 2022 (1642381515.1 104.1)
===== Config file =====
[virtual_sdcard]
path = /home/pi/gcode_files

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
variable_extrude = 1.0
gcode = 
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
	{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% if act_z < (max_z - 2.0) %}
	{% set z_safe = 2.0 %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{E} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe} F900
	G90
	G1 X{x_park} Y{y_park} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G91
	G1 E{E} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1969042216: New connection
webhooks client 1969042216: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1969042216: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:12:49 2022 (1642381969.7 558.7)
===== Config file =====
[virtual_sdcard]
path = /home/pi/gcode_files

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
variable_extrude = 1.0
gcode = 
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
	{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% if act_z < (max_z - 2.0) %}
	{% set z_safe = 2.0 %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{E} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe} F900
	G90
	G1 X{x_park} Y{y_park} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G91
	G1 E{E} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1969060520: New connection
webhooks client 1969060520: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1969060520: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:16:12 2022 (1642382172.4 761.5)
===== Config file =====
[virtual_sdcard]
path = /home/pi/gcode_files

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
variable_extrude = 1.0
gcode = 
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
	{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% if act_z < (max_z - 2.0) %}
	{% set z_safe = 2.0 %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{E} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe} F900
	G90
	G1 X{x_park} Y{y_park} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G91
	G1 E{E} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 283, in __init__
    self.add_extra_stepper(config)
  File "/home/pi/klipper/klippy/stepper.py", line 362, in add_extra_stepper
    pin_params = ppins.parse_pin(endstop_pin, True, True)
  File "/home/pi/klipper/klippy/pins.py", line 81, in parse_pin
    raise error("Unknown pin chip name '%s'" % (chip_name,))
error: Unknown pin chip name 'probe'
webhooks client 1969677136: New connection
webhooks client 1969677136: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1969677136: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:17:21 2022 (1642382241.9 831.0)
===== Config file =====
[virtual_sdcard]
path = ~/gcode_files

[stepper_x]
step_pin = ar54
dir_pin = ar55
enable_pin = !ar38
microsteps = 16
rotation_distance = 40
endstop_pin = ^!ar3
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = ar60
dir_pin = ar61
enable_pin = !ar56
microsteps = 16
rotation_distance = 40
endstop_pin = ^!ar14
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = ar46
dir_pin = !ar48
enable_pin = !ar62
microsteps = 16
rotation_distance = 8
endstop_pin = ^!ar18
position_endstop = 0
position_min = -3
position_max = 400
homing_speed = 30
second_homing_speed = 1

[stepper_z1]
step_pin = ar36
dir_pin = !ar34
enable_pin = !ar30
microsteps = 16
rotation_distance = 8
endstop_pin = ^!ar15

[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.600
filament_diameter = 1.750
heater_pin = ar10
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 240
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
min_temp = 5
max_temp = 150
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar49
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = ^ar19
control_pin = ar11
x_offset = 30
y_offset = -15
z_offset = 0
stow_on_each_sample = false
samples = 2

[bed_mesh]
speed = 120
horizontal_move_z = 5
mesh_min = 35,35
mesh_max = 280, 280
probe_count = 5,5

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[gcode_macro START_PRINT]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7
=======================
Extruder max_extrude_ratio=0.831503
mcu 'mcu': Starting serial connect
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
webhooks client 1971930056: New connection
webhooks client 1971930056: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
webhooks client 1971930056: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:17:29 2022 (1642382249.8 838.9)
===== Config file =====
[virtual_sdcard]
path = ~/gcode_files

[stepper_x]
step_pin = ar54
dir_pin = ar55
enable_pin = !ar38
microsteps = 16
rotation_distance = 40
endstop_pin = ^!ar3
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = ar60
dir_pin = ar61
enable_pin = !ar56
microsteps = 16
rotation_distance = 40
endstop_pin = ^!ar14
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = ar46
dir_pin = !ar48
enable_pin = !ar62
microsteps = 16
rotation_distance = 8
endstop_pin = ^!ar18
position_endstop = 0
position_min = -3
position_max = 400
homing_speed = 30
second_homing_speed = 1

[stepper_z1]
step_pin = ar36
dir_pin = !ar34
enable_pin = !ar30
microsteps = 16
rotation_distance = 8
endstop_pin = ^!ar15

[extruder]
step_pin = ar26
dir_pin = ar28
enable_pin = !ar24
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.600
filament_diameter = 1.750
heater_pin = ar10
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 240
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
min_temp = 5
max_temp = 150
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar49
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = ^ar19
control_pin = ar11
x_offset = 30
y_offset = -15
z_offset = 0
stow_on_each_sample = false
samples = 2

[bed_mesh]
speed = 120
horizontal_move_z = 5
mesh_min = 35,35
mesh_max = 280, 280
probe_count = 5,5

[mcu]
serial = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[gcode_macro START_PRINT]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7
=======================
Extruder max_extrude_ratio=0.831503
mcu 'mcu': Starting serial connect
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
webhooks client 1969781376: New connection
webhooks client 1969781376: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
MCU error during connect
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 158, in _connect
    self.send_event("klippy:mcu_identify")
  File "/home/pi/klipper/klippy/klippy.py", line 248, in send_event
    return [cb(*params) for cb in self.event_handlers.get(event, [])]
  File "/home/pi/klipper/klippy/mcu.py", line 779, in _mcu_identify
    raise error(str(e))
error: mcu 'mcu': Unable to connect
Build file /home/pi/klipper/klippy/../.config(1162): Mon Jan 17 00:56:26 2022
========= Last MCU build config =========
CONFIG_LOW_LEVEL_OPTIONS=y
# CONFIG_MACH_AVR is not set
# CONFIG_MACH_ATSAM is not set
# CONFIG_MACH_ATSAMD is not set
CONFIG_MACH_LPC176X=y
# CONFIG_MACH_STM32 is not set
# CONFIG_MACH_RP2040 is not set
# CONFIG_MACH_PRU is not set
# CONFIG_MACH_LINUX is not set
# CONFIG_MACH_SIMU is not set
CONFIG_BOARD_DIRECTORY="lpc176x"
CONFIG_MCU="lpc1769"
CONFIG_CLOCK_FREQ=120000000
CONFIG_SERIAL=y
CONFIG_FLASH_START=0x4000
CONFIG_FLASH_SIZE=0x80000
CONFIG_RAM_START=0x10000000
CONFIG_RAM_SIZE=0x7fe0
CONFIG_STACK_SIZE=512
CONFIG_LPC_SELECT=y
# CONFIG_MACH_LPC1768 is not set
CONFIG_MACH_LPC1769=y
CONFIG_SMOOTHIEWARE_BOOTLOADER=y
# CONFIG_LPC_USB is not set
CONFIG_LPC_SERIAL_UART0_P03_P02=y
# CONFIG_LPC_SERIAL_UART3_P429_P428 is not set
CONFIG_SERIAL_BAUD=250000
CONFIG_USB_VENDOR_ID=0x1d50
CONFIG_USB_DEVICE_ID=0x614e
CONFIG_USB_SERIAL_NUMBER_CHIPID=y
CONFIG_USB_SERIAL_NUMBER="12345"
CONFIG_INITIAL_PINS=""
CONFIG_HAVE_GPIO=y
CONFIG_HAVE_GPIO_ADC=y
CONFIG_HAVE_GPIO_SPI=y
CONFIG_HAVE_GPIO_I2C=y
CONFIG_HAVE_GPIO_HARD_PWM=y
CONFIG_HAVE_GPIO_BITBANGING=y
CONFIG_HAVE_STRICT_TIMING=y
CONFIG_HAVE_CHIPID=y
CONFIG_HAVE_STEPPER_BOTH_EDGE=y
CONFIG_INLINE_STEPPER_HACK=y
=======================
Build file /home/pi/klipper/klippy/../out/klipper.dict(6776): Mon Jan 17 00:56:45 2022
Last MCU build version: v0.10.0-234-g02d5f975
Last MCU build tools: gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-11+rpi1+11) 2.31.1
Last MCU build config: BUS_PINS_i2c1=P0.1,P0.0 BUS_PINS_i2c0=P0.28,P0.27 BUS_PINS_i2c2=P0.11,P0.10 BUS_PINS_i2c1a=P0.20,P0.19 BUS_PINS_ssp1=P0.8,P0.9,P0.7 STEPPER_BOTH_EDGE=1 SERIAL_BAUD=250000 ADC_MAX=4095 BUS_PINS_ssp0=P0.17,P0.18,P0.15 PWM_MAX=255 CLOCK_FREQ=120000000 RECEIVE_WINDOW=192 MCU=lpc1769 STATS_SUMSQ_BASE=256 RESERVE_PINS_serial=P0.3,P0.2
Build file /home/pi/klipper/klippy/../out/klipper.elf(250716): Mon Jan 17 00:56:53 2022
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0'
Restarting printer
Start printer at Mon Jan 17 01:32:43 2022 (1642383163.9 1752.9)
===== Config file =====
[virtuelle_sdkarte ]
pfad = ~/gcode_files

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 300

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ mcu ]
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[gcode_macro START_PRINT]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 295, in check_unused_options
    % (section,))
Error: Section 'virtuelle_sdkarte ' is not a valid config section
webhooks client 1969260064: New connection
webhooks client 1969260064: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00'
Restarting printer
Start printer at Mon Jan 17 01:32:49 2022 (1642383169.8 1758.9)
===== Config file =====
[virtuelle_sdkarte ]
pfad = ~/gcode_files

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 300

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ mcu ]
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[gcode_macro START_PRINT]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 295, in check_unused_options
    % (section,))
Error: Section 'virtuelle_sdkarte ' is not a valid config section
webhooks client 1971939408: New connection
webhooks client 1971939408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00'
Restarting printer
Start printer at Mon Jan 17 01:33:03 2022 (1642383183.3 1772.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 300

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ mcu ]
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[gcode_macro START_PRINT]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 295, in check_unused_options
    % (section,))
Error: Section ' mcu ' is not a valid config section
webhooks client 1971906720: New connection
webhooks client 1971906720: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00'
Restarting printer
Start printer at Mon Jan 17 01:36:34 2022 (1642383394.9 1984.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 300

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ mcu ]
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[gcode_macro START_PRINT]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 295, in check_unused_options
    % (section,))
Error: Section ' mcu ' is not a valid config section
webhooks client 1969379088: New connection
webhooks client 1969379088: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1969379088: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:37:16 2022 (1642383436.8 2025.9)
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ Drucker]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3   Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1972138392: New connection
webhooks client 1972138392: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1972138392: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:37:21 2022 (1642383441.9 2030.9)
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ Drucker]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3   Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971972176: New connection
webhooks client 1971972176: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971972176: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:37:24 2022 (1642383444.6 2033.6)
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ Drucker]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3   Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971923944: New connection
webhooks client 1971923944: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971923944: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:37:26 2022 (1642383446.2 2035.2)
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ Drucker]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3   Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971922704: New connection
webhooks client 1971922704: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971922704: Disconnected
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon Jan 17 01:38:08 2022 (1642383488.1 20.9)
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[ Drucker]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3   Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971048200: New connection
webhooks client 1971048200: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971048200: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:41:45 2022 (1642383705.6 227.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971196672: New connection
webhooks client 1971196672: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971196672: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:41:50 2022 (1642383710.8 232.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
seriell = /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1972410408: New connection
webhooks client 1972410408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1972410408: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:42:46 2022 (1642383766.7 288.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971205344: New connection
webhooks client 1971205344: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971205344: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:42:50 2022 (1642383770.5 292.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971120928: New connection
webhooks client 1971120928: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971120928: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:44:31 2022 (1642383871.2 392.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971048320: New connection
webhooks client 1971048320: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971048320: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:44:40 2022 (1642383880.2 401.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971184984: New connection
webhooks client 1971184984: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971184984: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:47:21 2022 (1642384041.7 563.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_y ]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 50

[ stepper_z ]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = !P1.27
position_endanschlag = 0,0
position_max = 300

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 33.500
dusendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 54.027
pid_ki = 0,770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ gcode_macro START_PRINT ]
gcode = 
	G28
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Extruder zurücksetzen
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3 Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; Stellen Sie die Einheiten auf Millimeter ein
	G90 ; Verwenden Sie absolute Koordinaten
	M83 ; Verwenden Sie relative Abstände für die Extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[display_status]

[gcode_macro PAUSE]
description = Pause the actual running print
rename_existing = PAUSE_BASE
gcode = 
	{% set x = params.X|default(230) %}
	{% set y = params.Y|default(230) %}
	{% set z = params.Z|default(10)|float %}
	{% set e = params.E|default(1) %}
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set act_z = printer.toolhead.position.z|float %}
	{% set lift_z = z|abs %}
	{% if act_z < (max_z - lift_z) %}
	{% set z_safe = lift_z %}
	{% else %}
	{% set z_safe = max_z - act_z %}
	{% endif %}
	PAUSE_BASE
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E-{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 Z{z_safe}
	G90
	G1 X{x} Y{y} F6000
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}

[gcode_macro RESUME]
description = Resume the actual running print
rename_existing = RESUME_BASE
gcode = 
	{% set e = params.E|default(1) %}
	{% if 'VELOCITY' in params|upper %}
	{% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
	{%else %}
	{% set get_params = "" %}
	{% endif %}
	G91
	{% if printer.extruder.can_extrude|lower == 'true' %}
	G1 E{e} F2100
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description = Cancel the actual running print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	TURN_OFF_HEATERS
	CANCEL_PRINT_BASE

[board_pins arduino-mega]
aliases = 
	ar0=PE0, ar1=PE1, ar2=PE4, ar3=PE5, ar4=PG5,
	ar5=PE3, ar6=PH3, ar7=PH4, ar8=PH5, ar9=PH6,
	ar10=PB4, ar11=PB5, ar12=PB6, ar13=PB7, ar14=PJ1,
	ar15=PJ0, ar16=PH1, ar17=PH0, ar18=PD3, ar19=PD2,
	ar20=PD1, ar21=PD0, ar22=PA0, ar23=PA1, ar24=PA2,
	ar25=PA3, ar26=PA4, ar27=PA5, ar28=PA6, ar29=PA7,
	ar30=PC7, ar31=PC6, ar32=PC5, ar33=PC4, ar34=PC3,
	ar35=PC2, ar36=PC1, ar37=PC0, ar38=PD7, ar39=PG2,
	ar40=PG1, ar41=PG0, ar42=PL7, ar43=PL6, ar44=PL5,
	ar45=PL4, ar46=PL3, ar47=PL2, ar48=PL1, ar49=PL0,
	ar50=PB3, ar51=PB2, ar52=PB1, ar53=PB0, ar54=PF0,
	ar55=PF1, ar56=PF2, ar57=PF3, ar58=PF4, ar59=PF5,
	ar60=PF6, ar61=PF7, ar62=PK0, ar63=PK1, ar64=PK2,
	ar65=PK3, ar66=PK4, ar67=PK5, ar68=PK6, ar69=PK7,
	analog0=PF0, analog1=PF1, analog2=PF2, analog3=PF3, analog4=PF4,
	analog5=PF5, analog6=PF6, analog7=PF7, analog8=PK0, analog9=PK1,
	analog10=PK2, analog11=PK3, analog12=PK4, analog13=PK5, analog14=PK6,
	analog15=PK7,
	ml70=PG4, ml71=PG3, ml72=PJ2, ml73=PJ3, ml74=PJ7,
	ml75=PJ4, ml76=PJ5, ml77=PJ6, ml78=PE2, ml79=PE6,
	ml80=PE7, ml81=PD4, ml82=PD5, ml83=PD6, ml84=PH2,
	ml85=PH7

[extruder]
control = pid
pid_kp = 21.415
pid_ki = 1.275
pid_kd = 89.944

[heater_bed]
control = pid
pid_kp = 44.060
pid_ki = 0.470
pid_kd = 1032.649
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971186384: New connection
webhooks client 1971186384: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971186384: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:50:39 2022 (1642384239.4 760.8)
===== Config file =====
[bltouch]
control_pin = P2.0
sensor_pin = P1.27
pin_up_touch_mode_reports_triggered = False
x_offset = -42
y_offset = -16
z_offset = 2.20

[homing_override]
gcode = 
	G90 ;
	G1 Z10 ;
	G28 X Y
	G1 X50 Y50 F6000 ;
	G28 Z ;
	BED_MESH_CALIBRATE ;
	G1 X0.1 Y20 F6000 ;
set_position_z = 0

[bed_mesh]
min_point = 50,50
max_point = 190,200
probe_count = 3,3
speed = 100
fade_end = 0.0

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 275
pressure_advance = 0.12

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1229, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 94, in __init__
    self.bmc = BedMeshCalibrate(config, self)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 291, in __init__
    self._init_mesh_config(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 428, in _init_mesh_config
    min_x, min_y = config.getfloatlist('mesh_min', count=2)
  File "/home/pi/klipper/klippy/configfile.py", line 107, in getfloatlist
    parser=float, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 95, in getlists
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'mesh_min' in section 'bed_mesh' must be specified
webhooks client 1971157192: New connection
webhooks client 1971157192: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 01:50:40 2022 (1642384240.8 762.3)
===== Config file =====
[bltouch]
control_pin = P2.0
sensor_pin = P1.27
pin_up_touch_mode_reports_triggered = False
x_offset = -42
y_offset = -16
z_offset = 2.20

[homing_override]
gcode = 
	G90 ;
	G1 Z10 ;
	G28 X Y
	G1 X50 Y50 F6000 ;
	G28 Z ;
	BED_MESH_CALIBRATE ;
	G1 X0.1 Y20 F6000 ;
set_position_z = 0

[bed_mesh]
min_point = 50,50
max_point = 190,200
probe_count = 3,3
speed = 100
fade_end = 0.0

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 275
pressure_advance = 0.12

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1229, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 94, in __init__
    self.bmc = BedMeshCalibrate(config, self)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 291, in __init__
    self._init_mesh_config(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 428, in _init_mesh_config
    min_x, min_y = config.getfloatlist('mesh_min', count=2)
  File "/home/pi/klipper/klippy/configfile.py", line 107, in getfloatlist
    parser=float, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 95, in getlists
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'mesh_min' in section 'bed_mesh' must be specified
webhooks client 1968721392: New connection
webhooks client 1968721392: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 01:51:32 2022 (1642384292.4 813.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 275
pressure_advance = 0.12

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1968160856: New connection
webhooks client 1968160856: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 01:53:01 2022 (1642384381.1 902.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 275
pressure_advance = 0.12
rotation_distance = 40

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 259, in parse_step_distance
    microsteps = config.getint('microsteps', minval=1, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'stepper_x' must be specified
webhooks client 1967468176: New connection
webhooks client 1967468176: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 01:53:36 2022 (1642384416.2 937.7)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 275
pressure_advance = 0.12
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 283, in __init__
    self.add_extra_stepper(config)
  File "/home/pi/klipper/klippy/stepper.py", line 362, in add_extra_stepper
    pin_params = ppins.parse_pin(endstop_pin, True, True)
  File "/home/pi/klipper/klippy/pins.py", line 81, in parse_pin
    raise error("Unknown pin chip name '%s'" % (chip_name,))
error: Unknown pin chip name 'probe'
webhooks client 1968145112: New connection
webhooks client 1968145112: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 01:54:39 2022 (1642384479.7 1001.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = !P1.28
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 275
pressure_advance = 0.12
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 283, in __init__
    self.add_extra_stepper(config)
  File "/home/pi/klipper/klippy/stepper.py", line 369, in add_extra_stepper
    mcu_endstop = ppins.setup_pin('endstop', endstop_pin)
  File "/home/pi/klipper/klippy/pins.py", line 115, in setup_pin
    pin_params = self.lookup_pin(pin_desc, can_invert, can_pullup)
  File "/home/pi/klipper/klippy/pins.py", line 104, in lookup_pin
    raise error("pin %s used multiple times in config" % (pin,))
error: pin P1.28 used multiple times in config
webhooks client 1968023232: New connection
webhooks client 1968023232: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 01:58:38 2022 (1642384718.9 1240.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 300

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'microsteps' is not valid in section 'tmc2208 stepper_x'
webhooks client 1967573672: New connection
webhooks client 1967573672: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1967573672: Disconnected
Restarting printer
Start printer at Mon Jan 17 01:59:45 2022 (1642384785.2 1306.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 235
homing_speed = 50

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 300

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 259, in parse_step_distance
    microsteps = config.getint('microsteps', minval=1, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'stepper_x' must be specified
webhooks client 1967654352: New connection
webhooks client 1967654352: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:00:34 2022 (1642384834.9 1356.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1967393648: New connection
webhooks client 1967393648: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1967393648: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:01:23 2022 (1642384884.0 1405.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 259, in parse_step_distance
    microsteps = config.getint('microsteps', minval=1, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'stepper_x' must be specified
webhooks client 1967735832: New connection
webhooks client 1967735832: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:02:03 2022 (1642384923.8 1445.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = probe:z_virtual_endstop
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 283, in __init__
    self.add_extra_stepper(config)
  File "/home/pi/klipper/klippy/stepper.py", line 362, in add_extra_stepper
    pin_params = ppins.parse_pin(endstop_pin, True, True)
  File "/home/pi/klipper/klippy/pins.py", line 81, in parse_pin
    raise error("Unknown pin chip name '%s'" % (chip_name,))
error: Unknown pin chip name 'probe'
webhooks client 1971178312: New connection
webhooks client 1971178312: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:02:44 2022 (1642384964.6 1486.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'step_distance' is not valid in section 'stepper_x'
webhooks client 1967450632: New connection
webhooks client 1967450632: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:07:02 2022 (1642385222.5 1743.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
step_distance = .0125
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'step_distance' is not valid in section 'stepper_x'
webhooks client 1968106392: New connection
webhooks client 1968106392: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:07:32 2022 (1642385252.0 1773.5)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'step_distance' is not valid in section 'stepper_y'
webhooks client 1967178896: New connection
webhooks client 1967178896: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1967178896: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:07:34 2022 (1642385254.6 1776.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
step_distance = .0125
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
step_distance = .0025
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = 0.00030120
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'step_distance' is not valid in section 'stepper_y'
webhooks client 1968103912: New connection
webhooks client 1968103912: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:07:54 2022 (1642385274.2 1795.7)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'microsteps' is not valid in section 'tmc2208 stepper_x'
webhooks client 1967613192: New connection
webhooks client 1967613192: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:08:08 2022 (1642385289.0 1810.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 259, in parse_step_distance
    microsteps = config.getint('microsteps', minval=1, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'stepper_x' must be specified
webhooks client 1967479104: New connection
webhooks client 1967479104: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:08:26 2022 (1642385306.6 1828.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endstop = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endstop = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endstop = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'microsteps' is not valid in section 'tmc2208 stepper_x'
webhooks client 1968397408: New connection
webhooks client 1968397408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:11:19 2022 (1642385479.8 2001.2)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotationsabstand = 40
microsteps = 16

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotationsabstand = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotationsabstand = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotationsabstand = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1967236960: New connection
webhooks client 1967236960: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:12:01 2022 (1642385521.5 2043.0)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotationsabstand = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1968300280: New connection
webhooks client 1968300280: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:13:10 2022 (1642385590.2 2111.7)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotationsabstand = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1968192048: New connection
webhooks client 1968192048: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:15:02 2022 (1642385702.8 2224.3)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1967950464: New connection
webhooks client 1967950464: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:15:20 2022 (1642385720.9 2242.4)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
microsteps = 16

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1967912400: New connection
webhooks client 1967912400: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:15:47 2022 (1642385747.2 2268.6)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
microsteps = 16

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1981993808: New connection
webhooks client 1981993808: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:16:06 2022 (1642385766.7 2288.1)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
microsteps = 16
rotation_distance = 38

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1967200176: New connection
webhooks client 1967200176: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:16:18 2022 (1642385778.5 2300.0)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
position_endanschlag = 0
position_max = 200
homing_speed = 100
microsteps = 16
rotation_distance = 0.025

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1967681368: New connection
webhooks client 1967681368: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:20:23 2022 (1642386023.6 2545.0)
===== Config file =====
[ stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
endstop_pin = P1.29
microsteps = 16
rotation_distance = 40
position_endstop = 0
position_max = 310
homing_speed = 40.0

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
endstop_pin = P1.28
position_endanschlag = 0
position_max = 235
homing_speed = 100
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
endstop_pin = !P1.27
position_endanschlag = 0
position_max = 200
position_min = -5
homing_speed = 75
second_homing_speed = 2
homing_retract_dist = 2
rotation_distance = 40
microsteps = 16

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 27
rotation_distance = 40
microsteps = 16

[ heizung_bett ]
heizungsstift = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
steuerung = PID
pid_kp = 67.599
pid_ki = 0.592
pid_kd = 1929.100
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan hotend]
pin = P2.4
heater = extruder
heater_temp = 40

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_x' must be specified
webhooks client 1968131128: New connection
webhooks client 1968131128: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:30:12 2022 (1642386612.1 3133.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = P1.29
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = P1.28
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = 0
position_max = 400
homing_speed = 30
second_homing_speed = 1

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 300
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0

[heater_bed]
heater_pin = ar8
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog14
min_temp = 5
max_temp = 150

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar7
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 28, in load_config
    return PrinterHeaterBed(config)
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 11, in __init__
    self.heater = pheaters.setup_heater(config, 'B')
  File "/home/pi/klipper/klippy/extras/heaters.py", line 265, in setup_heater
    self.heaters[heater_name] = heater = Heater(config, sensor)
  File "/home/pi/klipper/klippy/extras/heaters.py", line 47, in __init__
    algo = config.getchoice('control', algos)
  File "/home/pi/klipper/klippy/configfile.py", line 75, in getchoice
    c = self.get(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'control' in section 'heater_bed' must be specified
webhooks client 1967615032: New connection
webhooks client 1967615032: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:31:04 2022 (1642386664.0 3185.5)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = P1.29
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = P1.28
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = 0
position_max = 400
homing_speed = 30
second_homing_speed = 1

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 300
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar7
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1968160440: New connection
webhooks client 1968160440: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:31:36 2022 (1642386696.4 3217.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = P1.29
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = P1.28
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = 0
position_max = 400
homing_speed = 30
second_homing_speed = 1
homing_positive_dir = false

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 300
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar7
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1967485776: New connection
webhooks client 1967485776: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:32:50 2022 (1642386770.4 3291.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = P1.29
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = P1.28
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
homing_speed = 30
second_homing_speed = 1
homing_positive_dir = false

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 300
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar7
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1968113104: New connection
webhooks client 1968113104: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:33:17 2022 (1642386797.7 3319.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = P1.29
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = P1.28
position_endstop = 0
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
homing_speed = 30
second_homing_speed = 1
homing_positive_dir = false

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 300
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar7
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1968447696: New connection
webhooks client 1968447696: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:34:00 2022 (1642386840.8 3362.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = P1.29
position_endstop = 0
position_max = 310
homing_speed = 40.0

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = P1.28
position_endstop = 1
position_max = 310
homing_speed = 40
homing_positive_dir = false

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
homing_speed = 30
second_homing_speed = 1

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
sensor_type = EPCOS 100K B57560G104F
sensor_pin = analog13
min_extrude_temp = 190
min_temp = 5
max_temp = 300
max_extrude_only_distance = 500
max_extrude_cross_section = 2.0

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = ar9
kick_start_time = 0.500

[heater_fan my_nozzle_fan]
pin = ar7
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00

[printer]
kinematics = cartesian
max_velocity = 300
max_accel = 2500
max_z_velocity = 5
max_z_accel = 100

[display]
lcd_type = st7920
cs_pin = P1.19
sclk_pin = P1.21
sid_pin = P1.23
encoder_pins = ^P1.20, ^P1.18
click_pin = !P0.28

[virtual_sdcard]
path = /home/ender/.octoprint/uploads

[tmc2208 stepper_x]
uart_pin = P1.10
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_y]
uart_pin = P1.9
microsteps = 16
run_current = 0.800
hold_current = 0.500
stealthchop_threshold = 250

[tmc2208 stepper_z]
uart_pin = P1.8
microsteps = 16
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 30
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1968128968: New connection
webhooks client 1968128968: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_06D0FF0B22813AAFC6096A5CC22000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:37:10 2022 (1642387030.7 3552.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false
z_offset = 2.045

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84

[pause_resume]
recover_velocity = 50.

[tmc2209 stepper_x]
uart_pin = P1.10
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_y]
uart_pin = P1.9
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 250

[tmc2209 stepper_z]
uart_pin = P1.8
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 stepper_z1]
uart_pin = P1.1
run_current = 0.650
hold_current = 0.450
stealthchop_threshold = 250

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.650
hold_current = 0.500
stealthchop_threshold = 10
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1968397128: New connection
webhooks client 1968397128: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:37:31 2022 (1642387051.8 3573.2)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 274, in load_config
    blt = BLTouchEndstopWrapper(config)
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 33, in __init__
    self.position_endstop = config.getfloat('z_offset', minval=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'z_offset' in section 'bltouch' must be specified
webhooks client 1968107472: New connection
webhooks client 1968107472: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:38:17 2022 (1642387097.4 3618.9)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 274, in load_config
    blt = BLTouchEndstopWrapper(config)
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 33, in __init__
    self.position_endstop = config.getfloat('z_offset', minval=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'z_offset' in section 'bltouch' must be specified
webhooks client 1972884264: New connection
webhooks client 1972884264: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:38:52 2022 (1642387132.1 3653.6)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1971198392: New connection
webhooks client 1971198392: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:41:29 2022 (1642387289.3 3810.8)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
homing_endstop_align_zero = true

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 16, in __init__
    for n in 'xyz']
  File "/home/pi/klipper/klippy/stepper.py", line 401, in LookupMultiRail
    rail = PrinterRail(config)
  File "/home/pi/klipper/klippy/stepper.py", line 293, in __init__
    self.position_endstop = config.getfloat('position_endstop')
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'position_endstop' in section 'stepper_z' must be specified
webhooks client 1968616112: New connection
webhooks client 1968616112: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:43:22 2022 (1642387402.1 3923.6)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
webhooks client 1968411512: New connection
webhooks client 1968411512: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_0300011564084AAF89EC655DC42000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:44:05 2022 (1642387445.7 3967.2)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 1971133536: New connection
webhooks client 1971133536: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Loaded MCU 'mcu' 94 commands (v0.10.0-229-g89b4feca / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-11+rpi1+11) 2.31.1)
MCU 'mcu' config: BUS_PINS_i2c1=P0.1,P0.0 BUS_PINS_i2c0=P0.28,P0.27 BUS_PINS_i2c2=P0.11,P0.10 BUS_PINS_i2c1a=P0.20,P0.19 BUS_PINS_ssp1=P0.8,P0.9,P0.7 STEPPER_BOTH_EDGE=1 ADC_MAX=4095 BUS_PINS_ssp0=P0.17,P0.18,P0.15 PWM_MAX=255 CLOCK_FREQ=120000000 RESERVE_PINS_USB=P0.30,P0.29,P2.9 MCU=lpc1769 STATS_SUMSQ_BASE=256
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
Starting heater checks for heater_bed
bed_mesh: generated points
Index |  Tool Adjusted  |   Probe
  0   | (30.0, 30.0)    | (30.0, 30.0)
  1   | (90.0, 30.0)    | (90.0, 30.0)
  2   | (150.0, 30.0)   | (150.0, 30.0)
  3   | (210.0, 30.0)   | (210.0, 30.0)
  4   | (270.0, 30.0)   | (270.0, 30.0)
  5   | (270.0, 90.0)   | (270.0, 90.0)
  6   | (210.0, 90.0)   | (210.0, 90.0)
  7   | (150.0, 90.0)   | (150.0, 90.0)
  8   | (90.0, 90.0)    | (90.0, 90.0)
  9   | (30.0, 90.0)    | (30.0, 90.0)
  10  | (30.0, 150.0)   | (30.0, 150.0)
  11  | (90.0, 150.0)   | (90.0, 150.0)
  12  | (150.0, 150.0)  | (150.0, 150.0)
  13  | (210.0, 150.0)  | (210.0, 150.0)
  14  | (270.0, 150.0)  | (270.0, 150.0)
  15  | (270.0, 210.0)  | (270.0, 210.0)
  16  | (210.0, 210.0)  | (210.0, 210.0)
  17  | (150.0, 210.0)  | (150.0, 210.0)
  18  | (90.0, 210.0)   | (90.0, 210.0)
  19  | (30.0, 210.0)   | (30.0, 210.0)
  20  | (30.0, 270.0)   | (30.0, 270.0)
  21  | (90.0, 270.0)   | (90.0, 270.0)
  22  | (150.0, 270.0)  | (150.0, 270.0)
  23  | (210.0, 270.0)  | (210.0, 270.0)
  24  | (270.0, 270.0)  | (270.0, 270.0)
Starting heater checks for extruder
webhooks: registering remote method 'shutdown_machine' for connection id: 1971133536
webhooks: registering remote method 'reboot_machine' for connection id: 1971133536
webhooks: registering remote method 'pause_job_queue' for connection id: 1971133536
webhooks: registering remote method 'start_job_queue' for connection id: 1971133536
MCU 'mcu' shutdown: ADC out of range
clocksync state: mcu_freq=120000000 last_clock=758139270049 clock_est=(3967.754 757875328815 119996890.584) min_half_rtt=0.000190 min_rtt_time=3967.720 time_avg=3967.754(0.239) clock_avg=757875328815.391(28676804.428) pred_variance=9919985558.510
Dumping serial stats: bytes_write=1103 bytes_read=4015 bytes_retransmit=9 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0
Dumping send queue 100 messages
Sent 0 3967.482975 3967.482975 9: seq: 12, identify offset=720 count=40
Sent 1 3967.484343 3967.484343 9: seq: 13, identify offset=760 count=40
Sent 2 3967.485714 3967.485714 9: seq: 14, identify offset=800 count=40
Sent 3 3967.487085 3967.487085 9: seq: 15, identify offset=840 count=40
Sent 4 3967.488456 3967.488456 9: seq: 16, identify offset=880 count=40
Sent 5 3967.489834 3967.489834 9: seq: 17, identify offset=920 count=40
Sent 6 3967.491213 3967.491213 9: seq: 18, identify offset=960 count=40
Sent 7 3967.492609 3967.492609 9: seq: 19, identify offset=1000 count=40
Sent 8 3967.493961 3967.493961 9: seq: 1a, identify offset=1040 count=40
Sent 9 3967.495319 3967.495319 9: seq: 1b, identify offset=1080 count=40
Sent 10 3967.496702 3967.496702 9: seq: 1c, identify offset=1120 count=40
Sent 11 3967.498075 3967.498075 9: seq: 1d, identify offset=1160 count=40
Sent 12 3967.499477 3967.499477 9: seq: 1e, identify offset=1200 count=40
Sent 13 3967.500841 3967.500841 9: seq: 1f, identify offset=1240 count=40
Sent 14 3967.502365 3967.502365 9: seq: 10, identify offset=1280 count=40
Sent 15 3967.503681 3967.503681 9: seq: 11, identify offset=1320 count=40
Sent 16 3967.505043 3967.505043 9: seq: 12, identify offset=1360 count=40
Sent 17 3967.506418 3967.506418 9: seq: 13, identify offset=1400 count=40
Sent 18 3967.507784 3967.507784 9: seq: 14, identify offset=1440 count=40
Sent 19 3967.509100 3967.509100 9: seq: 15, identify offset=1480 count=40
Sent 20 3967.510478 3967.510478 9: seq: 16, identify offset=1520 count=40
Sent 21 3967.511842 3967.511842 9: seq: 17, identify offset=1560 count=40
Sent 22 3967.513258 3967.513258 9: seq: 18, identify offset=1600 count=40
Sent 23 3967.514607 3967.514607 9: seq: 19, identify offset=1640 count=40
Sent 24 3967.515983 3967.515983 9: seq: 1a, identify offset=1680 count=40
Sent 25 3967.517359 3967.517359 9: seq: 1b, identify offset=1720 count=40
Sent 26 3967.518729 3967.518729 9: seq: 1c, identify offset=1760 count=40
Sent 27 3967.520101 3967.520101 9: seq: 1d, identify offset=1800 count=40
Sent 28 3967.521482 3967.521482 9: seq: 1e, identify offset=1840 count=40
Sent 29 3967.522875 3967.522875 9: seq: 1f, identify offset=1880 count=40
Sent 30 3967.524264 3967.524264 9: seq: 10, identify offset=1920 count=40
Sent 31 3967.525602 3967.525602 9: seq: 11, identify offset=1960 count=40
Sent 32 3967.526985 3967.526985 9: seq: 12, identify offset=2000 count=40
Sent 33 3967.528352 3967.528352 9: seq: 13, identify offset=2040 count=40
Sent 34 3967.529726 3967.529726 9: seq: 14, identify offset=2080 count=40
Sent 35 3967.531102 3967.531102 9: seq: 15, identify offset=2120 count=40
Sent 36 3967.532506 3967.532506 9: seq: 16, identify offset=2160 count=40
Sent 37 3967.533869 3967.533869 9: seq: 17, identify offset=2200 count=40
Sent 38 3967.535228 3967.535228 9: seq: 18, identify offset=2240 count=40
Sent 39 3967.536605 3967.536605 9: seq: 19, identify offset=2280 count=40
Sent 40 3967.537977 3967.537977 9: seq: 1a, identify offset=2320 count=40
Sent 41 3967.539356 3967.539356 9: seq: 1b, identify offset=2360 count=40
Sent 42 3967.540730 3967.540730 9: seq: 1c, identify offset=2400 count=40
Sent 43 3967.542157 3967.542157 9: seq: 1d, identify offset=2440 count=40
Sent 44 3967.543492 3967.543492 9: seq: 1e, identify offset=2480 count=40
Sent 45 3967.544851 3967.544851 9: seq: 1f, identify offset=2520 count=40
Sent 46 3967.546210 3967.546210 9: seq: 10, identify offset=2522 count=40
Sent 47 3967.563379 3967.563379 6: seq: 11, get_uptime
Sent 48 3967.615601 3967.615601 6: seq: 12, get_clock
Sent 49 3967.667352 3967.667352 6: seq: 13, get_clock
Sent 50 3967.719787 3967.719787 6: seq: 14, get_clock
Sent 51 3967.771753 3967.771753 6: seq: 15, get_clock
Sent 52 3967.823550 3967.823550 6: seq: 16, get_clock
Sent 53 3967.874790 3967.874790 6: seq: 17, get_clock
Sent 54 3967.926264 3967.926264 6: seq: 18, get_clock
Sent 55 3967.978714 3967.978714 6: seq: 19, get_clock
Sent 56 3967.982321 3967.982321 6: seq: 1a, get_config
Sent 57 3967.982862 3967.982862 6: seq: 1b, get_clock
Sent 58 3967.996932 3967.996932 7: seq: 1c, allocate_oids count=22
Sent 59 3967.997282 3967.997282 8: seq: 1d, config_analog_in oid=11 pin=P0.25
Sent 60 3967.997724 3967.997724 15: seq: 1e, config_digital_out oid=12 pin=P2.5 value=0 default_value=0 max_duration=600000000
Sent 61 3967.997980 3967.997980 11: seq: 1f, set_digital_out_pwm_cycle oid=12 cycle_ticks=12000000
Sent 62 3967.998291 3967.998291 11: seq: 10, config_digital_out oid=13 pin=P2.3 value=0 default_value=0 max_duration=0
Sent 63 3967.998537 3967.998537 10: seq: 11, set_digital_out_pwm_cycle oid=13 cycle_ticks=1200000
Sent 64 3967.999127 3967.999127 11: seq: 12, config_digital_out oid=14 pin=P2.4 value=0 default_value=1 max_duration=0
Sent 65 3967.999390 3967.999390 10: seq: 13, set_digital_out_pwm_cycle oid=14 cycle_ticks=1200000
Sent 66 3967.999715 3967.999715 12: seq: 14, config_stepper oid=0 step_pin=P2.2 dir_pin=P2.6 invert_step=0 step_pulse_ticks=240
Sent 67 3968.000021 3968.000021 11: seq: 15, config_digital_out oid=15 pin=P2.1 value=1 default_value=1 max_duration=0
Sent 68 3968.000288 3968.000288 9: seq: 16, config_endstop oid=1 pin=P1.29 pull_up=0
Sent 69 3968.000535 3968.000535 7: seq: 17, config_trsync oid=2
Sent 70 3968.001198 3968.001198 12: seq: 18, config_stepper oid=3 step_pin=P0.19 dir_pin=P0.20 invert_step=0 step_pulse_ticks=240
Sent 71 3968.001507 3968.001507 11: seq: 19, config_digital_out oid=16 pin=P2.8 value=1 default_value=1 max_duration=0
Sent 72 3968.001770 3968.001770 9: seq: 1a, config_endstop oid=4 pin=P1.28 pull_up=0
Sent 73 3968.002161 3968.002161 7: seq: 1b, config_trsync oid=5
Sent 74 3968.003117 3968.003117 12: seq: 1c, config_stepper oid=6 step_pin=P0.22 dir_pin=P2.11 invert_step=0 step_pulse_ticks=240
Sent 75 3968.003462 3968.003462 11: seq: 1d, config_digital_out oid=17 pin=P0.21 value=1 default_value=1 max_duration=0
Sent 76 3968.003726 3968.003726 9: seq: 1e, config_endstop oid=7 pin=P1.25 pull_up=0
Sent 77 3968.003943 3968.003943 7: seq: 1f, config_trsync oid=8
Sent 78 3968.004627 3968.004627 12: seq: 10, config_stepper oid=9 step_pin=P1.15 dir_pin=P1.14 invert_step=0 step_pulse_ticks=240
Sent 79 3968.004939 3968.004939 11: seq: 11, config_digital_out oid=18 pin=P1.16 value=1 default_value=1 max_duration=0
Sent 80 3968.005183 3968.005183 8: seq: 12, config_analog_in oid=19 pin=P0.24
Sent 81 3968.005504 3968.005504 15: seq: 13, config_digital_out oid=20 pin=P2.7 value=0 default_value=0 max_duration=600000000
Sent 82 3968.005757 3968.005757 11: seq: 14, set_digital_out_pwm_cycle oid=20 cycle_ticks=12000000
Sent 83 3968.006436 3968.006436 12: seq: 15, config_stepper oid=10 step_pin=P2.13 dir_pin=P0.11 invert_step=0 step_pulse_ticks=240
Sent 84 3968.006748 3968.006748 11: seq: 16, config_digital_out oid=21 pin=P2.12 value=1 default_value=1 max_duration=0
Sent 85 3968.007006 3968.007006 11: seq: 17, finalize_config crc=2351459781
Sent 86 3968.007464 3968.007464 26: seq: 18, query_analog_in oid=11 clock=2138955904 sample_ticks=120000 sample_count=8 rest_ticks=36000000 min_value=12005 max_value=32303 range_check_count=4
Sent 87 3968.008120 3968.008120 13: seq: 19, queue_digital_out oid=12 clock=2012806692 on_ticks=0
Sent 88 3968.008406 3968.008406 13: seq: 1a, queue_digital_out oid=13 clock=2012836441 on_ticks=0
Sent 89 3968.008693 3968.008693 13: seq: 1b, queue_digital_out oid=14 clock=2012862066 on_ticks=0
Sent 90 3968.009122 3968.009122 25: seq: 1c, query_analog_in oid=19 clock=2148555904 sample_ticks=120000 sample_count=8 rest_ticks=36000000 min_value=1290 max_value=4117 range_check_count=4
Sent 91 3968.009501 3968.009501 13: seq: 1d, queue_digital_out oid=20 clock=2013825072 on_ticks=0
Sent 92 3968.009961 3968.009961 6: seq: 1e, get_config
Sent 93 3968.025421 3968.025421 7: seq: 1f, stepper_get_position oid=0
Sent 94 3968.028497 3968.028497 7: seq: 10, stepper_get_position oid=3
Sent 95 3968.030047 3968.030047 7: seq: 11, stepper_get_position oid=6
Sent 96 3968.032818 3968.032818 7: seq: 12, stepper_get_position oid=9
Sent 97 3968.035695 3968.035695 7: seq: 13, stepper_get_position oid=10
Sent 98 3968.968367 3968.968367 6: seq: 14, get_clock
Sent 99 3969.953100 3969.953100 6: seq: 15, get_clock
Dumping receive queue 92 messages
Receive: 0 3967.455408 3967.454885 48: seq: 11, identify_response offset=0 data='x\xda\x9d\x19ko\xe3\xc6\xf1\xafl\x05\x1c\x9ak\xce\xaeH=(\x19\xb8\x0f>\xc7i\x83\xc69\xc7\xbak\x0b\x04\x01A\x93+ia'
Receive: 1 3967.456780 3967.456305 48: seq: 12, identify_response offset=40 data='\xbe\x8eK\xfa\x91\xc0\xff\xbd\xf3\xd8\x97(\xe5\x02\xf4>X\xdc\xdd\xd9\x99\xd9y\xcf\xdc\xef\x93\xfbA\x95E\xfa(;\xad\x9aZO.&'
Receive: 2 3967.459428 3967.458072 48: seq: 13, identify_response offset=80 data='\xbb<\xbf\x10\xdfD\x8b\x8b\xe4,\x9eF\xab\xb3/\xf1\xd9\xf2\xadH\xceg\xe7\x91\xc0\x8d\xe92\x8e\xc57\x9d,e\xa6\xe5[\xf1\xcb\xe5'
Receive: 3 3967.462062 3967.461222 49: seq: 14, identify_response offset=120 data='\xdd\xcd\xdfeu/\x8bB\x16g\xc9\xd9}\x97\xd5\xf9^t\xf2Q!F\x11/\xa3\xf54\xf9U\xdc\xabz\xe8U\xa9\x01w|>\x8b'
Receive: 4 3967.463458 3967.462861 49: seq: 15, identify_response offset=160 data='\xce\xa3\xb3(\xfa\xb6kU\xf4m\x14\xbd\x15\xbc5y7\xc9\x9b\xaa\xca\xea\x02\x18\xf9}\x92\x95e\x93g\xbdL\x1bUh\x917C\xdd'
Receive: 5 3967.466058 3967.464902 49: seq: 16, identify_response offset=200 data='\xbf\x7f\x93O.\xe2\xe9;`\xbb\xef\x81\xdf4\xcb\x1f\x04\x1c\xc3~\x00\xb0\n\xce\x8b\xc2\x9e\xb7\x8d\xa6\x1fU\xbf\x7f3\x88v(\xcbt'
Receive: 6 3967.467391 3967.466876 49: seq: 17, identify_response offset=240 data='h\t~\x16\xfb\x0b_\x06\xd9\xbd8\x94\xc0\xc0\x03BwR\xf7i\xaf\xf2\x07\xcd\xab\x1e^\xa9+\xd5\xa7\x96\xa8P5\xc8\xd0\xf0\x17\xc1'
Receive: 7 3967.468753 3967.467962 49: seq: 18, identify_response offset=280 data=';@<]\xaa\xf7C_4O\xf5\xe4b\x89O\xab\xb7j\x07\x1c=\x97\xb3\xf9\xc2\x92\xd0\xadJ\xf9\x13\xf8\x98z\xa8:+\x9b]\xaa'
Receive: 8 3967.470123 3967.469229 49: seq: 19, identify_response offset=320 data='j\xc7=\xb1=\xb9X\xcc\x1d\x8ca\xd9B\xf02\xf5bX8H\xda\x93\xdd!\xae\x03\x11\xccc\x07\\\xa8\x9d\xea\xb32m\x86~t'
Receive: 9 3967.471500 3967.470589 49: seq: 1a, identify_response offset=360 data="\xe11+\x07\x89\xebBn\xb3\xa1\xecS\xb7Qe\xcfi1tY\x0f*'6c\xcf\xa6\x04u\xf6M{\x80+? \x1e{\xe2\xfb"
Receive: 10 3967.472874 3967.472006 49: seq: 1b, identify_response offset=400 data='b>OVS\x0b\xdc\xe9\xd4\xd0\x96\xf6\xa3\x98\xbb\xaf\x85\xfbZ\xba\xaf\xc4}\xc92{q:\x03i$\x8e\x88\x8asK\x00>A\x8e'
Receive: 11 3967.474249 3967.473352 49: seq: 1c, identify_response offset=440 data='\xacU05\xfc\x05\x93\x01u\xf3\xa5\xe5\xca]\xaae\xd3\xaagY\x8edRd}\x96j\xf5\x1b\\\xdd\x0f`\xe5}\x8a\xb2\x08LE'
Receive: 12 3967.475626 3967.474723 49: seq: 1d, identify_response offset=480 data="K\xd8Ru\xc8\x89G\xda>U'\xe4\x9c\xbf\x80\xf9x\x1cF\xca\xfba,w\xd89\x12|\xe4\xb5\x0e\xa65\xb6\x9e(\x0eO\x9d}"
Receive: 13 3967.476999 3967.476084 49: seq: 1e, identify_response offset=520 data='\x1e\x1b\xa3\xb0Gi\xa5w\xef\xdf\xfc\r\x1c2\x9e\x1d\xdc}R\xfd\x1eXOsk\x80\xf00o\xe5\xbaO\xd6\xb1Sc\xee\xd4\xa8\xf3'
Receive: 14 3967.478373 3967.477460 49: seq: 1f, identify_response offset=560 data='\xf2\xc1}\xab\xc2}\xbe\xd4yz\xa81\x91WE:V\xe2l\x15P\x90m\xebm\x1a\x97\xa9\xb1\xadBu\xf6\x93\xdd\x92\x80=\xd4P'
Receive: 15 3967.479746 3967.478835 49: seq: 10, identify_response offset=600 data='j\x19 \x9d{\x91\xf5{\xd9U\r\xb8K[\xca\x13B\t\x8f\xd3\xfe\xa5\x95\xec\xb6\xde\xd6\xfb*\x1f\xb2\xce\xe9\xb3{N\x8f|M\xf4'
Receive: 16 3967.481125 3967.480202 49: seq: 11, identify_response offset=640 data='n\x13\xad\xa5W\x95dS\x0b\xb8\xe8P\x1eN\xac \xf7B\xde\x0f`\x82M\x0bpk\xbb\x04,;\xb2?\xd6O\x94\xd8\x83Nf\x10'
Receive: 17 3967.482501 3967.481586 49: seq: 12, identify_response offset=680 data="\xf5\xbaBvH\x0f\xed\x99\xed.\xb6\x00O\x9d\xea\xe5\x11\x04\x1a\x1a\x0b\x040\xc9Jv;Y\xe7/):/0\x01d\x8d'\xa7\xfb"
Receive: 18 3967.483874 3967.482975 49: seq: 13, identify_response offset=720 data='\xa6\x92G!RgU\x1bZ\xadY\xbb\x00y\x18B\x81w\x1f=\xf8\xbdN\xc8\x9d\xda\xedd\x87\xaf\xd0h\xd4 \x81h\xee\x89S\x80'
Receive: 19 3967.485250 3967.484343 49: seq: 14, identify_response offset=760 data='\x06\xa6\xb2^:\t\x01o[\x05\x11\x13\xdc0e\x19\x8a\xbc\xcb9\x10\xbd\x9b\xec\xc0\x03\x89Mx\xd9\xcc,\t\x08\x84i\xd6C\x8bz'
Receive: 20 3967.486623 3967.485714 49: seq: 15, identify_response offset=800 data='\x00B\xb06!(\xd5@1\x05#t\x01\x16\xbfY\xd4\xf3\xf5\x08\x0c\xb5`\xc1\xbcFf\x90\x080\xc0TM\xa1\xb6/)\xa8\xdb\xe1'
Receive: 21 3967.487998 3967.487085 49: seq: 16, identify_response offset=840 data='\xea$y\x950y\x02X\xc0S\xe3hk\xbe\xc6j<\x84\xc7\xbd\xb4\x94\xec\xcd\xcb)\x03\x1au\x1e\x91\x07wT\x85\xac{ .\x9a'
Receive: 22 3967.489375 3967.488456 49: seq: 17, identify_response offset=880 data='\xed\x16\xa8\x90_\xb9\x04\x01\xec\xd9\xa8F\xcfp\xf2\x9cO\x83\x93\xa1-\xbc\xac9\x8b\xee\x87\x80\xcc\x02\xd0\xb0RF\xa9\xedt\xf6\x04\xb2'
Receive: 23 3967.490751 3967.489834 49: seq: 18, identify_response offset=920 data='\xd3\xd1\x05\xd2\xe6\x10\xc4\x91\x85\x03\x18\xa7\xc1\xff\xd3\xdc*on&h\xfa\x15\xa4\xf2\x1d\\\xdc\xcb\xfc!H\x9eqby\x18%O\xc7'
Receive: 24 3967.492126 3967.491213 49: seq: 19, identify_response offset=960 data='A\xdb\x80K\x8f\xe9\x07Q\xc5\xde?\x15S\xfe\xa0\xb0\x08\xd8<\xe0\x12\x9dwF\xf8\x06y*?;tM\x98g\x96\x89\xbd2J3'
Receive: 25 3967.493499 3967.492609 49: seq: 1a, identify_response offset=1000 data='\x0e\xdc\t\x01\xd8]Y`\x8c\x91.=\xe2\xcb9,X\xbb\xd9S\x86\x84_\x05\x9a\x04K\xa5\x0c\x07\xc6\x96\x98O\xba\xcf\xfe6\xa6\x07'
Receive: 26 3967.494869 3967.493961 49: seq: 1b, identify_response offset=1040 data='R\x05*\x08\x13\xbeaT\\L.\x92#\x18z\x00eE\x87\xf2 E\x02\xfbK\xbeT\xcbg\xc3\x01$\x01\xe7\x12\xaa#\xc4\xcb9'
Receive: 27 3967.496249 3967.495319 49: seq: 1c, identify_response offset=1080 data="\x03Yq\xfcI\xba\x85\xf7!\xbb\x98'\xbds\x84\x86\xbf\xb6\xa7=\xd6\x10a\xbe0%\x058\xbe\x0cJ\x0b`3\xf2Wt\xb3\xed\x9f"
Receive: 28 3967.497621 3967.496702 49: seq: 1d, identify_response offset=1120 data='\xb2N\x86w+\xa5\x1b\x9b\x1d\xaaF\xabSi\xf3\x08\xe9b\xcaH\xa9(\xddzK\r"\x018\x14g\xe4\xafE\xb5e|\x08u:'
Receive: 29 3967.499015 3967.498075 49: seq: 1e, identify_response offset=1160 data='\xa8\xc5(i\xce\xbd)\x86N\x08\x08\n\xab\x0f\xe7\xbd\xf1\xc2\x03P\xc4F\xa3\xe4\x98.\\\x88\x0f\x02>\x88\x19P\x9a\xccy j\x8a'
Receive: 30 3967.500376 3967.499477 49: seq: 1f, identify_response offset=1200 data="k.\xecqd\x02\x15\x9a\xdb(C\x8c\xda'\x0c\x1bPF\x1e\xae\x0f3\xb2l\x9b\xce\xa4\x03\xf6?Z;\xe5\xcb\xe7V\x81J\x82\xdc"
Receive: 31 3967.501748 3967.500841 49: seq: 10, identify_response offset=1240 data='3\x9b9L\xa3W\x04@K \xc7q\xf2\x94{z\xd3^._m\x96\xc7\x0e\xe7\xf2\xbb\xab\xf4\xe6\xf2\xbf\x18p\xd7 \xb5\x0f\x9f7'
Receive: 32 3967.503128 3967.502365 49: seq: 11, identify_response offset=1280 data='\xe9\xed\x0f?m\xb0@\x9dB+v;=\x07\x87\xc1\xbf\xc9\xe4\xf04\xe2\xd3\x08\x0f\xa7\xe3\xb3\xcc\\\x9d\xe2i\xb4\x1e\x1d\xc7\xe6*\xdd'
Receive: 33 3967.504502 3967.503681 49: seq: 12, identify_response offset=1320 data='\x8d\x0e.k\xdd\x1a\xb2PK\xe0_"\x1e-F0\x868\x1d\xae\xf1\x0frw\xf5\xe3\xc7\xab\x7f\xa5\xdf\xdf]\xff\x8cU\xe6\x94\xff\xbd'
Receive: 34 3967.505875 3967.505043 49: seq: 13, identify_response offset=1360 data='\x9b\xdc\\}\x06\xe8\xb2\xcd\xa3d\x89\x9c\xdc\xfe\xe7\x86_\x1cc\x90\xbf\xbb\xde\\\xdf\xfd\xfb\x9a1\x7f\xde|`\xc43b\x1c\xb2\xe0m'
Receive: 35 3967.507249 3967.506418 49: seq: 14, identify_response offset=1400 data='|\x8ew6\x9f.?m\xd2\xcd\xe7\x9b\xcd\xcf\xe9\x87\xcb\xcd5^^\xe2\xf6\xf5\xed\xed\xf5]\xfa\xe1\xe3\xa7\x7f\xa6\xd7\xdf\xfd\x03\xf6\xa3'
Receive: 36 3967.508625 3967.507784 49: seq: 15, identify_response offset=1440 data="W\xac\x13\x06(]\xa8 \xa6.\xd2T\xf8\xe6sJ\x15\x01K\x90\xb3'\x8a\x8b\xf34Hf\x06\x08\xc0\xcd\x10\x98${\xf1\xcb\xf4\xdd"
Receive: 37 3967.510001 3967.509100 49: seq: 16, identify_response offset=1480 data=',\xfe\x15\xf8\x8eh\x05\x9d"/cZB@\xe1\xe5\x8c\x96\xeb\xa5Y\xcei\x19\x81\xf2`\xfd\xca\xdeix`\x19\xa3\xc7\x92 \x91c'
Receive: 38 3967.511375 3967.510478 49: seq: 17, identify_response offset=1520 data='\xcc~\n\xed\xb4\x83\x82.U\x85\xb1\x0cA\x16\xb4\xe5\xfc\xc4~wY\xa2#\xbc\x08[\xec\x14\\\xb1\\e\xb5\xa8\x9b^\x80G\x08\x8c'
Receive: 39 3967.512756 3967.511842 49: seq: 18, identify_response offset=1560 data='*\x02\x02\x1cG5A\x86-\x9e\xf6\n\xbe\xd9@\xb5h\xc1\xc5\x80\x127\xd2p\xf7\xaf=Ft(\xc7w\x80\x15j\xdc\xac\x17J\x8b'
Receive: 40 3967.514127 3967.513258 49: seq: 19, identify_response offset=1600 data="\xcc\xd0\xca\xf2^=Jvk\x03\xac\x11\x14\x8d\x9b\xfd\x8cw)\xf8\x0btH 'ka\xebsw\x1f\xe4~\xc5\xdd\xbdh\xb3N\xc3"
Receive: 41 3967.515507 3967.514607 49: seq: 1a, identify_response offset=1640 data='\x91\xec\xba\xa6\xa3xo\x0f:\t9H\xf7\xd4\xc2\x7f\x9f\x01\xd3\x85\xe8\x1bA1\x01\x9b6re\x0e\x02?\xd4\xe0U\xaa\x10\xb6\t\xf6'
Receive: 42 3967.516877 3967.515983 49: seq: 1b, identify_response offset=1680 data="=9'*.\xcb-\x94\x19+PO\xec\xf7\x00\x0cY\xc9*\tY\x8e\x1b\x1c{\x88\xd4Hc\x98X\xecf\xd5<J\xcb\xa2\xc0\x9e"
Receive: 43 3967.518252 3967.517359 49: seq: 1c, identify_response offset=1720 data='\x8f+S{\xec:D\xd7\x13r\xd9|tn**\xc7\x14v5\x16\x08\xa4*\xb0\xb3\xe0^\xcd\xeeb+g\xc3\x06V&\xc1>\xc6'
Receive: 44 3967.519628 3967.518729 49: seq: 1d, identify_response offset=1760 data="\xc1\xa1\xf5\xef\xd0\\\xbf[\x88\x83\xea#\xdf\xab\xd6`\xc7Y\xc3M\xf6\x8c\x06\xb6\xb2B\xe4\x92\xf1\x06\x9a\xdfl'\x05\x14\xff\x90i\xac"
Receive: 45 3967.521004 3967.520101 49: seq: 1e, identify_response offset=1800 data='\x92\xf0@i\r\n\xd1P*\x15C\x89\xcd\x07\\\xc6\x84+L\xcc#\x8b\x95\x8f\x12\xa5\x8fC\x90?\xbe\xb0\xcf\xba\x82\xac\xd4@c\x90'
Receive: 46 3967.522380 3967.521482 49: seq: 1f, identify_response offset=1840 data='\xbdA\xe9R\t"\xe0\xab\xdb\x96\xcd\x13\xb7\xb3?\x81ig\x82\x9f\x83~A\x0e\x8a\x95|x\x00\x81\x85\x0f0\x1b\xd2A\r\xd5K\xcb'
Receive: 47 3967.523774 3967.522875 49: seq: 10, identify_response offset=1880 data='Y\x9e+Z\xb3\x0bL\xfa\xed\x88B\x923\xf6\xb6kv \xc7\n\xb8\xce\xf0Y[H\xa7\xc0 \xc8Y\xa2\xb3a\xdd\x8f\xe0\x06\x85\xbd'
Receive: 48 3967.525128 3967.524264 49: seq: 11, identify_response offset=1920 data='\x05\xe5\xe9\xa0%\xd7Pw\xd2<\x17M\x17\x9c\xa1\xc3SP\x02(\x08\xed\x1a\xe7,\x1b\x07p$7\xf1\xa4\xca\x12\x92P\x0e\xe4\x0ez'
Receive: 49 3967.526506 3967.525602 49: seq: 12, identify_response offset=1960 data="{\xae\xb5\xfcM'\xbb\xaf\xdc\xc0\xb1\xd6\x06|\x92\xb5K\x0c \x84\xaa\x86\xca\xeeYW\x01)o\xec,\x80Z\x12@F^La\xc5"
Receive: 50 3967.527877 3967.526985 49: seq: 13, identify_response offset=2000 data='M\xb1\x10\xa1q\xeb\xbei\xc46\xa3\xd7\xf1\xcbp\xe2\xf3)4\xb6\x13!l=\x02A\xf1\x01.\x1ajpq\xf8\x89D\x86\xc8!E'
Receive: 51 3967.529253 3967.528352 49: seq: 14, identify_response offset=2040 data='\xa3LA\xcd4\x07\x84\x02}\xa8\x1f\x00\x14\x83\x027\xbb\xc1\xbe\xf6\x07~\x06\xc1\x11\xa9\xa9K\x08b\x8fp\x9c\xdd\x9766\xb9\x17q'
Receive: 52 3967.530628 3967.529726 49: seq: 15, identify_response offset=2080 data='\xab%L\x1d\xc1\xb3\x80Q\xcbv!>Bt\x84\xacr\x8f\xa9\x7f\x8b]\xbb\xfe\x0b7w4\x98t\x81\xd2\x8c+\x0b\xeep46^'
Receive: 53 3967.532014 3967.531102 49: seq: 16, identify_response offset=2120 data='5x;[A\x0e\xc7dB\xae\xd4\xa10AO-\xb3\x0e\xc5\x83%\xf4\x89"\x02U\xc06\x8e#\x17\x13O\xd9Q\xb0B\x85\x04r'
Receive: 54 3967.533379 3967.532506 49: seq: 17, identify_response offset=2160 data='4\x96\xc0\x0c\x02Yv\x16\xad\x16\x0bJ6f\xb1\xa4T\xc7\x8b\xe5\x82\xf4\t\x8b\xe52Y`\xea{\xa5\n\xbe\x85@ y\xfej\xba'
Receive: 55 3967.534753 3967.533869 49: seq: 18, identify_response offset=2200 data='\xb3\xb0\x0e\xd4\x18\xfd\xea\\\x8ez\xc0\x15\xaa\xe3T3\xe7{\r\xd3\x0c\xd9B\x8b\x0b\xf5\x10\xdb\xfd@\xdeF\xb7\xb6j\xdb\xe0o\xa9\x82'
Receive: 56 3967.536126 3967.535228 49: seq: 19, identify_response offset=2240 data='!+V\xe4+P\xafk\n\x0f\xa6\x00\x8c\xf1Tk\xb3\n\xc6\xbb\x077\xb2\xa0\xe3\x13tb^\x83S&j`|A\x99\xb8\xf1\x0c'
Receive: 57 3967.537503 3967.536605 49: seq: 1a, identify_response offset=2280 data='$G3?\xa0\xf7\xd1\x9c\x01\xf7\xacQQ\x1d\x0f\x11,d;!\xab\xa4>\xf2kL\x9b\x1b\xe6#\xf5\xd4\xd7\x91\x9f\xedhp\x167'
Receive: 58 3967.538879 3967.537977 49: seq: 1b, identify_response offset=2320 data='\xaaIV~2r\x80x\xdf@3\xb9;&\x11\x0e^\xe0\xa5S?jH\xad\xf2}}\xcbk#\x94\x85\x9f&\x04\xa0n\xac\xc0\xc6'
Receive: 59 3967.540254 3967.539356 49: seq: 1c, identify_response offset=2360 data='p\x8e\xa0\x88\xd4\xcbC\x8c\xeb\x1b#\x92p\xfa`^e\x8dl\xc8s\x9a\xc0\xe2h\x07\x90\x01\xa9p\xd0\x95`\x83\xe8\xa3\x95\x1d\x08\x9c'
Receive: 60 3967.541629 3967.540730 49: seq: 1d, identify_response offset=2400 data='\xa6\x12\x1f\xf6F\x7f\xf6\xc8\x19\x95c]O\xf5Q2\xe5\xe2L{\xc5\xe8\xa12?\xfa\x0b+`\xe6\xbb\x9dQ+\xc4\xb3\x12h\x93\x93'
Receive: 61 3967.543004 3967.542157 49: seq: 1e, identify_response offset=2440 data='\xf5\xc8G\x0f\x9f{\xd2p\x07\x8e\x8a\xac%\x1f4N\xf0\x8f\x9d\x11\xf1\xbe\x0e[\x1eo\ty\xe6\xfa\xaf\x93\xe3\xb5\xc0\xc8W\xd4\xc6P'
Receive: 62 3967.544378 3967.543492 49: seq: 1f, identify_response offset=2480 data='\r\xb7W\xbb=Y\xa2\xf7\x809\x04\x08\xf3\x1fEP\xa8?b\xf7p>=\x8b\xe3\xf5\xd9n\xb5\xbe\x9foe\x9eM^\xff\x07gA'
Receive: 63 3967.545752 3967.544851 11: seq: 10, identify_response offset=2520 data='\xc2p'
Receive: 64 3967.547126 3967.546210 9: seq: 11, identify_response offset=2522 data=''
Receive: 65 3967.564800 3967.563379 13: seq: 12, uptime high=176 clock=1938267377
Receive: 66 3967.616133 3967.615601 11: seq: 13, clock clock=1944536113
Receive: 67 3967.668760 3967.667352 11: seq: 14, clock clock=1950742068
Receive: 68 3967.720166 3967.719787 11: seq: 15, clock clock=1957037128
Receive: 69 3967.772774 3967.771753 11: seq: 16, clock clock=1963271533
Receive: 70 3967.824131 3967.823550 11: seq: 17, clock clock=1969484723
Receive: 71 3967.875503 3967.874790 11: seq: 18, clock clock=1975632923
Receive: 72 3967.926926 3967.926264 11: seq: 19, clock clock=1981811593
Receive: 73 3967.979595 3967.978714 11: seq: 1a, clock clock=1988109533
Receive: 74 3967.983443 3967.982321 10: seq: 1b, config is_config=0 crc=0 is_shutdown=0 move_count=0
Receive: 75 3967.983852 3967.982862 11: seq: 1c, clock clock=1988604518
Receive: 76 3968.011156 3968.009961 15: seq: 1f, config is_config=1 crc=2351459781 is_shutdown=0 move_count=1024
Receive: 77 3968.026291 3968.025421 8: seq: 10, stepper_position oid=0 pos=0
Receive: 78 3968.028915 3968.028497 8: seq: 11, stepper_position oid=3 pos=0
Receive: 79 3968.031608 3968.030047 8: seq: 12, stepper_position oid=6 pos=0
Receive: 80 3968.034202 3968.032818 8: seq: 13, stepper_position oid=9 pos=0
Receive: 81 3968.036829 3968.035695 8: seq: 14, stepper_position oid=10 pos=0
Receive: 82 3968.969442 3968.968367 11: seq: 15, clock clock=2106862418
Receive: 83 3969.244572 3968.968367 15: seq: 15, analog_in_state oid=11 next_clock=2174955904 value=31555
Receive: 84 3969.324717 3968.968367 15: seq: 15, analog_in_state oid=19 next_clock=2184555904 value=31583
Receive: 85 3969.543665 3968.968367 15: seq: 15, analog_in_state oid=11 next_clock=2210955904 value=31553
Receive: 86 3969.623710 3968.968367 15: seq: 15, analog_in_state oid=19 next_clock=2220555904 value=31580
Receive: 87 3969.843876 3968.968367 15: seq: 15, analog_in_state oid=11 next_clock=2246955904 value=31551
Receive: 88 3969.923996 3968.968367 15: seq: 15, analog_in_state oid=19 next_clock=2256555904 value=31579
Receive: 89 3969.954068 3969.953100 11: seq: 16, clock clock=2225025953
Receive: 90 3970.144207 3969.953100 15: seq: 16, analog_in_state oid=11 next_clock=2282955904 value=31552
Receive: 91 3970.224380 3969.953100 12: seq: 16, shutdown clock=2257428189 static_string_id=ADC out of range
Transition to shutdown state: MCU 'mcu' shutdown: ADC out of range
This generally occurs when a heater temperature exceeds
its configured min_temp or max_temp.
Dumping gcode input 0 blocks
Dumping 20 requests for client 1971133536
Received 3968.499922: {"id": 1731450000, "method": "objects/query", "params": {"objects": {"heaters": null}}}
Received 3968.501277: {"id": 1731815760, "method": "objects/query", "params": {"objects": {"heaters": null}}}
Received 3968.524548: {"id": 1731815984, "method": "info", "params": {}}
Received 3968.526353: {"id": 1731901552, "method": "objects/list", "params": {}}
Received 3968.526353: {"id": 1731903376, "method": "gcode/help", "params": {}}
Received 3968.526353: {"id": 1731258128, "method": "info", "params": {}}
Received 3968.531129: {"id": 1731260144, "method": "objects/list", "params": {}}
Received 3968.531129: {"id": 1731257424, "method": "gcode/help", "params": {}}
Received 3968.531129: {"id": 1731901744, "method": "info", "params": {}}
Received 3968.531129: {"id": 1731258896, "method": "objects/list", "params": {}}
Received 3968.531129: {"id": 1731256752, "method": "gcode/help", "params": {}}
Received 3968.584308: {"id": 1731902896, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "configfile": null, "mcu": null, "heaters": null, "heater_bed": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null, "extruder": null}, "response_template": {"method": "process_status_update"}}}
Received 3968.589862: {"id": 1731815152, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "configfile": null, "mcu": null, "heaters": null, "heater_bed": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null, "extruder": null}, "response_template": {"method": "process_status_update"}}}
Received 3968.634970: {"id": 1731813584, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "configfile": null, "mcu": null, "heaters": null, "heater_bed": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null, "extruder": null}, "response_template": {"method": "process_status_update"}}}
Received 3968.707959: {"id": 1731257584, "method": "info", "params": {}}
Received 3968.735891: {"id": 1740419152, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 3968.737195: {"id": 1731816592, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 3968.973396: {"id": 1731452656, "method": "info", "params": {}}
Received 3968.977389: {"id": 1721564560, "method": "list_endpoints", "params": {}}
Received 3969.057008: {"id": 1721563088, "method": "info", "params": {}}
gcode state: absolute_coord=True absolute_extrude=True base_position=[0.0, 0.0, 0.0, 0.0] last_position=[0.0, 0.0, 0.0, 0.0] homing_position=[0.0, 0.0, 0.0, 0.0] speed_factor=0.0166666666667 extrude_factor=1.0 speed=25.0
Reactor garbage collection: (3968.538907757, 0.0, 0.0)
Attempting MCU 'mcu' reset command
webhooks client 1971133536: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:44:33 2022 (1642387473.6 3995.1)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00'
webhooks client 1967786184: New connection
webhooks client 1967786184: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Loaded MCU 'mcu' 94 commands (v0.10.0-229-g89b4feca / gcc: (15:7-2018-q2-6) 7.3.1 20180622 (release) [ARM/embedded-7-branch revision 261907] binutils: (2.31.1-11+rpi1+11) 2.31.1)
MCU 'mcu' config: BUS_PINS_i2c1=P0.1,P0.0 BUS_PINS_i2c0=P0.28,P0.27 BUS_PINS_i2c2=P0.11,P0.10 BUS_PINS_i2c1a=P0.20,P0.19 BUS_PINS_ssp1=P0.8,P0.9,P0.7 STEPPER_BOTH_EDGE=1 ADC_MAX=4095 BUS_PINS_ssp0=P0.17,P0.18,P0.15 PWM_MAX=255 CLOCK_FREQ=120000000 RESERVE_PINS_USB=P0.30,P0.29,P2.9 MCU=lpc1769 STATS_SUMSQ_BASE=256
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
Starting heater checks for heater_bed
bed_mesh: generated points
Index |  Tool Adjusted  |   Probe
  0   | (30.0, 30.0)    | (30.0, 30.0)
  1   | (90.0, 30.0)    | (90.0, 30.0)
  2   | (150.0, 30.0)   | (150.0, 30.0)
  3   | (210.0, 30.0)   | (210.0, 30.0)
  4   | (270.0, 30.0)   | (270.0, 30.0)
  5   | (270.0, 90.0)   | (270.0, 90.0)
  6   | (210.0, 90.0)   | (210.0, 90.0)
  7   | (150.0, 90.0)   | (150.0, 90.0)
  8   | (90.0, 90.0)    | (90.0, 90.0)
  9   | (30.0, 90.0)    | (30.0, 90.0)
  10  | (30.0, 150.0)   | (30.0, 150.0)
  11  | (90.0, 150.0)   | (90.0, 150.0)
  12  | (150.0, 150.0)  | (150.0, 150.0)
  13  | (210.0, 150.0)  | (210.0, 150.0)
  14  | (270.0, 150.0)  | (270.0, 150.0)
  15  | (270.0, 210.0)  | (270.0, 210.0)
  16  | (210.0, 210.0)  | (210.0, 210.0)
  17  | (150.0, 210.0)  | (150.0, 210.0)
  18  | (90.0, 210.0)   | (90.0, 210.0)
  19  | (30.0, 210.0)   | (30.0, 210.0)
  20  | (30.0, 270.0)   | (30.0, 270.0)
  21  | (90.0, 270.0)   | (90.0, 270.0)
  22  | (150.0, 270.0)  | (150.0, 270.0)
  23  | (210.0, 270.0)  | (210.0, 270.0)
  24  | (270.0, 270.0)  | (270.0, 270.0)
Starting heater checks for extruder
Stats 4001.0: gcodein=0 mcu: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1091 bytes_read=3865 bytes_retransmit=9 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119990202 heater_bed: target=0 temp=0.0 pwm=0.000 sysload=0.20 cputime=76.411 memavail=763632 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=0.0 pwm=0.000
webhooks: registering remote method 'shutdown_machine' for connection id: 1967786184
webhooks: registering remote method 'reboot_machine' for connection id: 1967786184
webhooks: registering remote method 'pause_job_queue' for connection id: 1967786184
webhooks: registering remote method 'start_job_queue' for connection id: 1967786184
Stats 4002.0: gcodein=0 mcu: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1097 bytes_read=3911 bytes_retransmit=9 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119996515 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.20 cputime=76.467 memavail=763592 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
MCU 'mcu' shutdown: ADC out of range
clocksync state: mcu_freq=120000000 last_clock=866929679 clock_est=(4000.601 712387678 119996515.997) min_half_rtt=0.000155 min_rtt_time=4000.799 time_avg=4000.601(0.074) clock_avg=712387678.868(8916432.409) pred_variance=10264636313.495
Dumping serial stats: bytes_write=1097 bytes_read=3998 bytes_retransmit=9 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0
Dumping send queue 100 messages
Sent 0 4000.404945 4000.404945 9: seq: 11, identify offset=680 count=40
Sent 1 4000.406313 4000.406313 9: seq: 12, identify offset=720 count=40
Sent 2 4000.407688 4000.407688 9: seq: 13, identify offset=760 count=40
Sent 3 4000.409061 4000.409061 9: seq: 14, identify offset=800 count=40
Sent 4 4000.410433 4000.410433 9: seq: 15, identify offset=840 count=40
Sent 5 4000.411806 4000.411806 9: seq: 16, identify offset=880 count=40
Sent 6 4000.413193 4000.413193 9: seq: 17, identify offset=920 count=40
Sent 7 4000.414566 4000.414566 9: seq: 18, identify offset=960 count=40
Sent 8 4000.415937 4000.415937 9: seq: 19, identify offset=1000 count=40
Sent 9 4000.417317 4000.417317 9: seq: 1a, identify offset=1040 count=40
Sent 10 4000.418688 4000.418688 9: seq: 1b, identify offset=1080 count=40
Sent 11 4000.420062 4000.420062 9: seq: 1c, identify offset=1120 count=40
Sent 12 4000.421444 4000.421444 9: seq: 1d, identify offset=1160 count=40
Sent 13 4000.422829 4000.422829 9: seq: 1e, identify offset=1200 count=40
Sent 14 4000.424193 4000.424193 9: seq: 1f, identify offset=1240 count=40
Sent 15 4000.425567 4000.425567 9: seq: 10, identify offset=1280 count=40
Sent 16 4000.426937 4000.426937 9: seq: 11, identify offset=1320 count=40
Sent 17 4000.428302 4000.428302 9: seq: 12, identify offset=1360 count=40
Sent 18 4000.429683 4000.429683 9: seq: 13, identify offset=1400 count=40
Sent 19 4000.431058 4000.431058 9: seq: 14, identify offset=1440 count=40
Sent 20 4000.432451 4000.432451 9: seq: 15, identify offset=1480 count=40
Sent 21 4000.433816 4000.433816 9: seq: 16, identify offset=1520 count=40
Sent 22 4000.435195 4000.435195 9: seq: 17, identify offset=1560 count=40
Sent 23 4000.436561 4000.436561 9: seq: 18, identify offset=1600 count=40
Sent 24 4000.437937 4000.437937 9: seq: 19, identify offset=1640 count=40
Sent 25 4000.439317 4000.439317 9: seq: 1a, identify offset=1680 count=40
Sent 26 4000.440690 4000.440690 9: seq: 1b, identify offset=1720 count=40
Sent 27 4000.442105 4000.442105 9: seq: 1c, identify offset=1760 count=40
Sent 28 4000.443450 4000.443450 9: seq: 1d, identify offset=1800 count=40
Sent 29 4000.444846 4000.444846 9: seq: 1e, identify offset=1840 count=40
Sent 30 4000.446188 4000.446188 9: seq: 1f, identify offset=1880 count=40
Sent 31 4000.447562 4000.447562 9: seq: 10, identify offset=1920 count=40
Sent 32 4000.448938 4000.448938 9: seq: 11, identify offset=1960 count=40
Sent 33 4000.450313 4000.450313 9: seq: 12, identify offset=2000 count=40
Sent 34 4000.451690 4000.451690 9: seq: 13, identify offset=2040 count=40
Sent 35 4000.453073 4000.453073 9: seq: 14, identify offset=2080 count=40
Sent 36 4000.454436 4000.454436 9: seq: 15, identify offset=2120 count=40
Sent 37 4000.455809 4000.455809 9: seq: 16, identify offset=2160 count=40
Sent 38 4000.457187 4000.457187 9: seq: 17, identify offset=2200 count=40
Sent 39 4000.458560 4000.458560 9: seq: 18, identify offset=2240 count=40
Sent 40 4000.459936 4000.459936 9: seq: 19, identify offset=2280 count=40
Sent 41 4000.461309 4000.461309 9: seq: 1a, identify offset=2320 count=40
Sent 42 4000.462719 4000.462719 9: seq: 1b, identify offset=2360 count=40
Sent 43 4000.464070 4000.464070 9: seq: 1c, identify offset=2400 count=40
Sent 44 4000.465442 4000.465442 9: seq: 1d, identify offset=2440 count=40
Sent 45 4000.466818 4000.466818 9: seq: 1e, identify offset=2480 count=40
Sent 46 4000.468191 4000.468191 9: seq: 1f, identify offset=2520 count=40
Sent 47 4000.469558 4000.469558 9: seq: 10, identify offset=2522 count=40
Sent 48 4000.486951 4000.486951 6: seq: 11, get_uptime
Sent 49 4000.539431 4000.539431 6: seq: 12, get_clock
Sent 50 4000.591545 4000.591545 6: seq: 13, get_clock
Sent 51 4000.643144 4000.643144 6: seq: 14, get_clock
Sent 52 4000.694167 4000.694167 6: seq: 15, get_clock
Sent 53 4000.746422 4000.746422 6: seq: 16, get_clock
Sent 54 4000.798580 4000.798580 6: seq: 17, get_clock
Sent 55 4000.849640 4000.849640 6: seq: 18, get_clock
Sent 56 4000.901267 4000.901267 6: seq: 19, get_clock
Sent 57 4000.903874 4000.903874 6: seq: 1a, get_config
Sent 58 4000.904612 4000.904612 6: seq: 1b, get_clock
Sent 59 4000.916964 4000.916964 7: seq: 1c, allocate_oids count=22
Sent 60 4000.917126 4000.917126 8: seq: 1d, config_analog_in oid=11 pin=P0.25
Sent 61 4000.917755 4000.917755 15: seq: 1e, config_digital_out oid=12 pin=P2.5 value=0 default_value=0 max_duration=600000000
Sent 62 4000.917906 4000.917906 11: seq: 1f, set_digital_out_pwm_cycle oid=12 cycle_ticks=12000000
Sent 63 4000.918400 4000.918400 11: seq: 10, config_digital_out oid=13 pin=P2.3 value=0 default_value=0 max_duration=0
Sent 64 4000.918761 4000.918761 10: seq: 11, set_digital_out_pwm_cycle oid=13 cycle_ticks=1200000
Sent 65 4000.919168 4000.919168 11: seq: 12, config_digital_out oid=14 pin=P2.4 value=0 default_value=1 max_duration=0
Sent 66 4000.919315 4000.919315 10: seq: 13, set_digital_out_pwm_cycle oid=14 cycle_ticks=1200000
Sent 67 4000.919702 4000.919702 12: seq: 14, config_stepper oid=0 step_pin=P2.2 dir_pin=P2.6 invert_step=0 step_pulse_ticks=240
Sent 68 4000.920410 4000.920410 11: seq: 15, config_digital_out oid=15 pin=P2.1 value=1 default_value=1 max_duration=0
Sent 69 4000.920566 4000.920566 9: seq: 16, config_endstop oid=1 pin=P1.29 pull_up=0
Sent 70 4000.920808 4000.920808 7: seq: 17, config_trsync oid=2
Sent 71 4000.921087 4000.921087 12: seq: 18, config_stepper oid=3 step_pin=P0.19 dir_pin=P0.20 invert_step=0 step_pulse_ticks=240
Sent 72 4000.921363 4000.921363 11: seq: 19, config_digital_out oid=16 pin=P2.8 value=1 default_value=1 max_duration=0
Sent 73 4000.921593 4000.921593 9: seq: 1a, config_endstop oid=4 pin=P1.28 pull_up=0
Sent 74 4000.921896 4000.921896 7: seq: 1b, config_trsync oid=5
Sent 75 4000.922370 4000.922370 12: seq: 1c, config_stepper oid=6 step_pin=P0.22 dir_pin=P2.11 invert_step=0 step_pulse_ticks=240
Sent 76 4000.922565 4000.922565 11: seq: 1d, config_digital_out oid=17 pin=P0.21 value=1 default_value=1 max_duration=0
Sent 77 4000.922860 4000.922860 9: seq: 1e, config_endstop oid=7 pin=P1.25 pull_up=0
Sent 78 4000.922969 4000.922969 7: seq: 1f, config_trsync oid=8
Sent 79 4000.923326 4000.923326 12: seq: 10, config_stepper oid=9 step_pin=P1.15 dir_pin=P1.14 invert_step=0 step_pulse_ticks=240
Sent 80 4000.923889 4000.923889 11: seq: 11, config_digital_out oid=18 pin=P1.16 value=1 default_value=1 max_duration=0
Sent 81 4000.924024 4000.924024 8: seq: 12, config_analog_in oid=19 pin=P0.24
Sent 82 4000.924370 4000.924370 15: seq: 13, config_digital_out oid=20 pin=P2.7 value=0 default_value=0 max_duration=600000000
Sent 83 4000.924509 4000.924509 11: seq: 14, set_digital_out_pwm_cycle oid=20 cycle_ticks=12000000
Sent 84 4000.924889 4000.924889 12: seq: 15, config_stepper oid=10 step_pin=P2.13 dir_pin=P0.11 invert_step=0 step_pulse_ticks=240
Sent 85 4000.925183 4000.925183 11: seq: 16, config_digital_out oid=21 pin=P2.12 value=1 default_value=1 max_duration=0
Sent 86 4000.925633 4000.925633 11: seq: 17, finalize_config crc=2351459781
Sent 87 4000.926033 4000.926033 26: seq: 18, query_analog_in oid=11 clock=853200000 sample_ticks=120000 sample_count=8 rest_ticks=36000000 min_value=12005 max_value=32303 range_check_count=4
Sent 88 4000.926196 4000.926196 13: seq: 19, queue_digital_out oid=12 clock=772908067 on_ticks=0
Sent 89 4000.926495 4000.926495 13: seq: 1a, queue_digital_out oid=13 clock=772953794 on_ticks=0
Sent 90 4000.926667 4000.926667 13: seq: 1b, queue_digital_out oid=14 clock=772981347 on_ticks=0
Sent 91 4000.927407 4000.927407 25: seq: 1c, query_analog_in oid=19 clock=862800000 sample_ticks=120000 sample_count=8 rest_ticks=36000000 min_value=1290 max_value=4117 range_check_count=4
Sent 92 4000.927568 4000.927568 13: seq: 1d, queue_digital_out oid=20 clock=773799918 on_ticks=0
Sent 93 4000.927943 4000.927943 6: seq: 1e, get_config
Sent 94 4000.940864 4000.940864 7: seq: 1f, stepper_get_position oid=0
Sent 95 4000.943654 4000.943654 7: seq: 10, stepper_get_position oid=3
Sent 96 4000.945632 4000.945632 7: seq: 11, stepper_get_position oid=6
Sent 97 4000.948136 4000.948136 7: seq: 12, stepper_get_position oid=9
Sent 98 4000.951152 4000.951152 7: seq: 13, stepper_get_position oid=10
Sent 99 4001.888894 4001.888894 6: seq: 14, get_clock
Dumping receive queue 91 messages
Receive: 0 4000.382504 4000.381631 48: seq: 11, identify_response offset=0 data='x\xda\x9d\x19ko\xe3\xc6\xf1\xafl\x05\x1c\x9ak\xce\xaeH=(\x19\xb8\x0f>\xc7i\x83\xc69\xc7\xbak\x0b\x04\x01A\x93+ia'
Receive: 1 4000.383880 4000.383014 48: seq: 12, identify_response offset=40 data='\xbe\x8eK\xfa\x91\xc0\xff\xbd\xf3\xd8\x97(\xe5\x02\xf4>X\xdc\xdd\xd9\x99\xd9y\xcf\xdc\xef\x93\xfbA\x95E\xfa(;\xad\x9aZO.&'
Receive: 2 4000.385253 4000.384328 48: seq: 13, identify_response offset=80 data='\xbb<\xbf\x10\xdfD\x8b\x8b\xe4,\x9eF\xab\xb3/\xf1\xd9\xf2\xadH\xceg\xe7\x91\xc0\x8d\xe92\x8e\xc57\x9d,e\xa6\xe5[\xf1\xcb\xe5'
Receive: 3 4000.386628 4000.385689 49: seq: 14, identify_response offset=120 data='\xdd\xcd\xdfeu/\x8bB\x16g\xc9\xd9}\x97\xd5\xf9^t\xf2Q!F\x11/\xa3\xf54\xf9U\xdc\xabz\xe8U\xa9\x01w|>\x8b'
Receive: 4 4000.388003 4000.387068 49: seq: 15, identify_response offset=160 data='\xce\xa3\xb3(\xfa\xb6kU\xf4m\x14\xbd\x15\xbc5y7\xc9\x9b\xaa\xca\xea\x02\x18\xf9}\x92\x95e\x93g\xbdL\x1bUh\x917C\xdd'
Receive: 5 4000.389378 4000.388441 49: seq: 16, identify_response offset=200 data='\xbf\x7f\x93O.\xe2\xe9;`\xbb\xef\x81\xdf4\xcb\x1f\x04\x1c\xc3~\x00\xb0\n\xce\x8b\xc2\x9e\xb7\x8d\xa6\x1fU\xbf\x7f3\x88v(\xcbt'
Receive: 6 4000.390752 4000.389813 49: seq: 17, identify_response offset=240 data='h\t~\x16\xfb\x0b_\x06\xd9\xbd8\x94\xc0\xc0\x03BwR\xf7i\xaf\xf2\x07\xcd\xab\x1e^\xa9+\xd5\xa7\x96\xa8P5\xc8\xd0\xf0\x17\xc1'
Receive: 7 4000.392136 4000.391185 49: seq: 18, identify_response offset=280 data=';@<]\xaa\xf7C_4O\xf5\xe4b\x89O\xab\xb7j\x07\x1c=\x97\xb3\xf9\xc2\x92\xd0\xadJ\xf9\x13\xf8\x98z\xa8:+\x9b]\xaa'
Receive: 8 4000.393504 4000.392575 49: seq: 19, identify_response offset=320 data='j\xc7=\xb1=\xb9X\xcc\x1d\x8ca\xd9B\xf02\xf5bX8H\xda\x93\xdd!\xae\x03\x11\xccc\x07\\\xa8\x9d\xea\xb32m\x86~t'
Receive: 9 4000.394879 4000.393938 49: seq: 1a, identify_response offset=360 data="\xe11+\x07\x89\xebBn\xb3\xa1\xecS\xb7Qe\xcfi1tY\x0f*'6c\xcf\xa6\x04u\xf6M{\x80+? \x1e{\xe2\xfb"
Receive: 10 4000.396252 4000.395313 49: seq: 1b, identify_response offset=400 data='b>OVS\x0b\xdc\xe9\xd4\xd0\x96\xf6\xa3\x98\xbb\xaf\x85\xfbZ\xba\xaf\xc4}\xc92{q:\x03i$\x8e\x88\x8asK\x00>A\x8e'
Receive: 11 4000.397630 4000.396695 49: seq: 1c, identify_response offset=440 data='\xacU05\xfc\x05\x93\x01u\xf3\xa5\xe5\xca]\xaae\xd3\xaagY\x8edRd}\x96j\xf5\x1b\\\xdd\x0f`\xe5}\x8a\xb2\x08LE'
Receive: 12 4000.399005 4000.398066 49: seq: 1d, identify_response offset=480 data="K\xd8Ru\xc8\x89G\xda>U'\xe4\x9c\xbf\x80\xf9x\x1cF\xca\xfba,w\xd89\x12|\xe4\xb5\x0e\xa65\xb6\x9e(\x0eO\x9d}"
Receive: 13 4000.400377 4000.399438 49: seq: 1e, identify_response offset=520 data='\x1e\x1b\xa3\xb0Gi\xa5w\xef\xdf\xfc\r\x1c2\x9e\x1d\xdc}R\xfd\x1eXOsk\x80\xf00o\xe5\xbaO\xd6\xb1Sc\xee\xd4\xa8\xf3'
Receive: 14 4000.401755 4000.400814 49: seq: 1f, identify_response offset=560 data='\xf2\xc1}\xab\xc2}\xbe\xd4yz\xa81\x91WE:V\xe2l\x15P\x90m\xebm\x1a\x97\xa9\xb1\xadBu\xf6\x93\xdd\x92\x80=\xd4P'
Receive: 15 4000.403129 4000.402241 49: seq: 10, identify_response offset=600 data='j\x19 \x9d{\x91\xf5{\xd9U\r\xb8K[\xca\x13B\t\x8f\xd3\xfe\xa5\x95\xec\xb6\xde\xd6\xfb*\x1f\xb2\xce\xe9\xb3{N\x8f|M\xf4'
Receive: 16 4000.404501 4000.403574 49: seq: 11, identify_response offset=640 data='n\x13\xad\xa5W\x95dS\x0b\xb8\xe8P\x1eN\xac \xf7B\xde\x0f`\x82M\x0bpk\xbb\x04,;\xb2?\xd6O\x94\xd8\x83Nf\x10'
Receive: 17 4000.405877 4000.404945 49: seq: 12, identify_response offset=680 data="\xf5\xbaBvH\x0f\xed\x99\xed.\xb6\x00O\x9d\xea\xe5\x11\x04\x1a\x1a\x0b\x040\xc9Jv;Y\xe7/):/0\x01d\x8d'\xa7\xfb"
Receive: 18 4000.407253 4000.406313 49: seq: 13, identify_response offset=720 data='\xa6\x92G!RgU\x1bZ\xadY\xbb\x00y\x18B\x81w\x1f=\xf8\xbdN\xc8\x9d\xda\xedd\x87\xaf\xd0h\xd4 \x81h\xee\x89S\x80'
Receive: 19 4000.408628 4000.407688 49: seq: 14, identify_response offset=760 data='\x06\xa6\xb2^:\t\x01o[\x05\x11\x13\xdc0e\x19\x8a\xbc\xcb9\x10\xbd\x9b\xec\xc0\x03\x89Mx\xd9\xcc,\t\x08\x84i\xd6C\x8bz'
Receive: 20 4000.410004 4000.409061 49: seq: 15, identify_response offset=800 data='\x00B\xb06!(\xd5@1\x05#t\x01\x16\xbfY\xd4\xf3\xf5\x08\x0c\xb5`\xc1\xbcFf\x90\x080\xc0TM\xa1\xb6/)\xa8\xdb\xe1'
Receive: 21 4000.411379 4000.410433 49: seq: 16, identify_response offset=840 data='\xea$y\x950y\x02X\xc0S\xe3hk\xbe\xc6j<\x84\xc7\xbd\xb4\x94\xec\xcd\xcb)\x03\x1au\x1e\x91\x07wT\x85\xac{ .\x9a'
Receive: 22 4000.412756 4000.411806 49: seq: 17, identify_response offset=880 data='\xed\x16\xa8\x90_\xb9\x04\x01\xec\xd9\xa8F\xcfp\xf2\x9cO\x83\x93\xa1-\xbc\xac9\x8b\xee\x87\x80\xcc\x02\xd0\xb0RF\xa9\xedt\xf6\x04\xb2'
Receive: 23 4000.414129 4000.413193 49: seq: 18, identify_response offset=920 data='\xd3\xd1\x05\xd2\xe6\x10\xc4\x91\x85\x03\x18\xa7\xc1\xff\xd3\xdc*on&h\xfa\x15\xa4\xf2\x1d\\\xdc\xcb\xfc!H\x9eqby\x18%O\xc7'
Receive: 24 4000.415502 4000.414566 49: seq: 19, identify_response offset=960 data='A\xdb\x80K\x8f\xe9\x07Q\xc5\xde?\x15S\xfe\xa0\xb0\x08\xd8<\xe0\x12\x9dwF\xf8\x06y*?;tM\x98g\x96\x89\xbd2J3'
Receive: 25 4000.416879 4000.415937 49: seq: 1a, identify_response offset=1000 data='\x0e\xdc\t\x01\xd8]Y`\x8c\x91.=\xe2\xcb9,X\xbb\xd9S\x86\x84_\x05\x9a\x04K\xa5\x0c\x07\xc6\x96\x98O\xba\xcf\xfe6\xa6\x07'
Receive: 26 4000.418251 4000.417317 49: seq: 1b, identify_response offset=1040 data='R\x05*\x08\x13\xbeaT\\L.\x92#\x18z\x00eE\x87\xf2 E\x02\xfbK\xbeT\xcbg\xc3\x01$\x01\xe7\x12\xaa#\xc4\xcb9'
Receive: 27 4000.419629 4000.418688 49: seq: 1c, identify_response offset=1080 data="\x03Yq\xfcI\xba\x85\xf7!\xbb\x98'\xbds\x84\x86\xbf\xb6\xa7=\xd6\x10a\xbe0%\x058\xbe\x0cJ\x0b`3\xf2Wt\xb3\xed\x9f"
Receive: 28 4000.421008 4000.420062 49: seq: 1d, identify_response offset=1120 data='\xb2N\x86w+\xa5\x1b\x9b\x1d\xaaF\xabSi\xf3\x08\xe9b\xcaH\xa9(\xddzK\r"\x018\x14g\xe4\xafE\xb5e|\x08u:'
Receive: 29 4000.422379 4000.421444 49: seq: 1e, identify_response offset=1160 data='\xa8\xc5(i\xce\xbd)\x86N\x08\x08\n\xab\x0f\xe7\xbd\xf1\xc2\x03P\xc4F\xa3\xe4\x98.\\\x88\x0f\x02>\x88\x19P\x9a\xccy j\x8a'
Receive: 30 4000.423754 4000.422829 49: seq: 1f, identify_response offset=1200 data="k.\xecqd\x02\x15\x9a\xdb(C\x8c\xda'\x0c\x1bPF\x1e\xae\x0f3\xb2l\x9b\xce\xa4\x03\xf6?Z;\xe5\xcb\xe7V\x81J\x82\xdc"
Receive: 31 4000.425131 4000.424193 49: seq: 10, identify_response offset=1240 data='3\x9b9L\xa3W\x04@K \xc7q\xf2\x94{z\xd3^._m\x96\xc7\x0e\xe7\xf2\xbb\xab\xf4\xe6\xf2\xbf\x18p\xd7 \xb5\x0f\x9f7'
Receive: 32 4000.426502 4000.425567 49: seq: 11, identify_response offset=1280 data='\xe9\xed\x0f?m\xb0@\x9dB+v;=\x07\x87\xc1\xbf\xc9\xe4\xf04\xe2\xd3\x08\x0f\xa7\xe3\xb3\xcc\\\x9d\xe2i\xb4\x1e\x1d\xc7\xe6*\xdd'
Receive: 33 4000.427877 4000.426937 49: seq: 12, identify_response offset=1320 data='\x8d\x0e.k\xdd\x1a\xb2PK\xe0_"\x1e-F0\x868\x1d\xae\xf1\x0frw\xf5\xe3\xc7\xab\x7f\xa5\xdf\xdf]\xff\x8cU\xe6\x94\xff\xbd'
Receive: 34 4000.429253 4000.428302 49: seq: 13, identify_response offset=1360 data='\x9b\xdc\\}\x06\xe8\xb2\xcd\xa3d\x89\x9c\xdc\xfe\xe7\x86_\x1cc\x90\xbf\xbb\xde\\\xdf\xfd\xfb\x9a1\x7f\xde|`\xc43b\x1c\xb2\xe0m'
Receive: 35 4000.430626 4000.429683 49: seq: 14, identify_response offset=1400 data='|\x8ew6\x9f.?m\xd2\xcd\xe7\x9b\xcd\xcf\xe9\x87\xcb\xcd5^^\xe2\xf6\xf5\xed\xed\xf5]\xfa\xe1\xe3\xa7\x7f\xa6\xd7\xdf\xfd\x03\xf6\xa3'
Receive: 36 4000.432011 4000.431058 49: seq: 15, identify_response offset=1440 data="W\xac\x13\x06(]\xa8 \xa6.\xd2T\xf8\xe6sJ\x15\x01K\x90\xb3'\x8a\x8b\xf34Hf\x06\x08\xc0\xcd\x10\x98${\xf1\xcb\xf4\xdd"
Receive: 37 4000.433379 4000.432451 49: seq: 16, identify_response offset=1480 data=',\xfe\x15\xf8\x8eh\x05\x9d"/cZB@\xe1\xe5\x8c\x96\xeb\xa5Y\xcei\x19\x81\xf2`\xfd\xca\xdeix`\x19\xa3\xc7\x92 \x91c'
Receive: 38 4000.434752 4000.433816 49: seq: 17, identify_response offset=1520 data='\xcc~\n\xed\xb4\x83\x82.U\x85\xb1\x0cA\x16\xb4\xe5\xfc\xc4~wY\xa2#\xbc\x08[\xec\x14\\\xb1\\e\xb5\xa8\x9b^\x80G\x08\x8c'
Receive: 39 4000.436126 4000.435195 49: seq: 18, identify_response offset=1560 data='*\x02\x02\x1cG5A\x86-\x9e\xf6\n\xbe\xd9@\xb5h\xc1\xc5\x80\x127\xd2p\xf7\xaf=Ft(\xc7w\x80\x15j\xdc\xac\x17J\x8b'
Receive: 40 4000.437503 4000.436561 49: seq: 19, identify_response offset=1600 data="\xcc\xd0\xca\xf2^=Jvk\x03\xac\x11\x14\x8d\x9b\xfd\x8cw)\xf8\x0btH 'ka\xebsw\x1f\xe4~\xc5\xdd\xbdh\xb3N\xc3"
Receive: 41 4000.438878 4000.437937 49: seq: 1a, identify_response offset=1640 data='\x91\xec\xba\xa6\xa3xo\x0f:\t9H\xf7\xd4\xc2\x7f\x9f\x01\xd3\x85\xe8\x1bA1\x01\x9b6re\x0e\x02?\xd4\xe0U\xaa\x10\xb6\t\xf6'
Receive: 42 4000.440253 4000.439317 49: seq: 1b, identify_response offset=1680 data="=9'*.\xcb-\x94\x19+PO\xec\xf7\x00\x0cY\xc9*\tY\x8e\x1b\x1c{\x88\xd4Hc\x98X\xecf\xd5<J\xcb\xa2\xc0\x9e"
Receive: 43 4000.441630 4000.440690 49: seq: 1c, identify_response offset=1720 data='\x8f+S{\xec:D\xd7\x13r\xd9|tn**\xc7\x14v5\x16\x08\xa4*\xb0\xb3\xe0^\xcd\xeeb+g\xc3\x06V&\xc1>\xc6'
Receive: 44 4000.443006 4000.442105 49: seq: 1d, identify_response offset=1760 data="\xc1\xa1\xf5\xef\xd0\\\xbf[\x88\x83\xea#\xdf\xab\xd6`\xc7Y\xc3M\xf6\x8c\x06\xb6\xb2B\xe4\x92\xf1\x06\x9a\xdfl'\x05\x14\xff\x90i\xac"
Receive: 45 4000.444377 4000.443450 49: seq: 1e, identify_response offset=1800 data='\x92\xf0@i\r\n\xd1P*\x15C\x89\xcd\x07\\\xc6\x84+L\xcc#\x8b\x95\x8f\x12\xa5\x8fC\x90?\xbe\xb0\xcf\xba\x82\xac\xd4@c\x90'
Receive: 46 4000.445754 4000.444846 49: seq: 1f, identify_response offset=1840 data='\xbdA\xe9R\t"\xe0\xab\xdb\x96\xcd\x13\xb7\xb3?\x81ig\x82\x9f\x83~A\x0e\x8a\x95|x\x00\x81\x85\x0f0\x1b\xd2A\r\xd5K\xcb'
Receive: 47 4000.447131 4000.446188 49: seq: 10, identify_response offset=1880 data='Y\x9e+Z\xb3\x0bL\xfa\xed\x88B\x923\xf6\xb6kv \xc7\n\xb8\xce\xf0Y[H\xa7\xc0 \xc8Y\xa2\xb3a\xdd\x8f\xe0\x06\x85\xbd'
Receive: 48 4000.448503 4000.447562 49: seq: 11, identify_response offset=1920 data='\x05\xe5\xe9\xa0%\xd7Pw\xd2<\x17M\x17\x9c\xa1\xc3SP\x02(\x08\xed\x1a\xe7,\x1b\x07p$7\xf1\xa4\xca\x12\x92P\x0e\xe4\x0ez'
Receive: 49 4000.449877 4000.448938 49: seq: 12, identify_response offset=1960 data="{\xae\xb5\xfcM'\xbb\xaf\xdc\xc0\xb1\xd6\x06|\x92\xb5K\x0c \x84\xaa\x86\xca\xeeYW\x01)o\xec,\x80Z\x12@F^La\xc5"
Receive: 50 4000.451253 4000.450313 49: seq: 13, identify_response offset=2000 data='M\xb1\x10\xa1q\xeb\xbei\xc46\xa3\xd7\xf1\xcbp\xe2\xf3)4\xb6\x13!l=\x02A\xf1\x01.\x1ajpq\xf8\x89D\x86\xc8!E'
Receive: 51 4000.452628 4000.451690 49: seq: 14, identify_response offset=2040 data='\xa3LA\xcd4\x07\x84\x02}\xa8\x1f\x00\x14\x83\x027\xbb\xc1\xbe\xf6\x07~\x06\xc1\x11\xa9\xa9K\x08b\x8fp\x9c\xdd\x9766\xb9\x17q'
Receive: 52 4000.454003 4000.453073 49: seq: 15, identify_response offset=2080 data='\xab%L\x1d\xc1\xb3\x80Q\xcbv!>Bt\x84\xacr\x8f\xa9\x7f\x8b]\xbb\xfe\x0b7w4\x98t\x81\xd2\x8c+\x0b\xeep46^'
Receive: 53 4000.455379 4000.454436 49: seq: 16, identify_response offset=2120 data='5x;[A\x0e\xc7dB\xae\xd4\xa10AO-\xb3\x0e\xc5\x83%\xf4\x89"\x02U\xc06\x8e#\x17\x13O\xd9Q\xb0B\x85\x04r'
Receive: 54 4000.456752 4000.455809 49: seq: 17, identify_response offset=2160 data='4\x96\xc0\x0c\x02Yv\x16\xad\x16\x0bJ6f\xb1\xa4T\xc7\x8b\xe5\x82\xf4\t\x8b\xe52Y`\xea{\xa5\n\xbe\x85@ y\xfej\xba'
Receive: 55 4000.458128 4000.457187 49: seq: 18, identify_response offset=2200 data='\xb3\xb0\x0e\xd4\x18\xfd\xea\\\x8ez\xc0\x15\xaa\xe3T3\xe7{\r\xd3\x0c\xd9B\x8b\x0b\xf5\x10\xdb\xfd@\xdeF\xb7\xb6j\xdb\xe0o\xa9\x82'
Receive: 56 4000.459505 4000.458560 49: seq: 19, identify_response offset=2240 data='!+V\xe4+P\xafk\n\x0f\xa6\x00\x8c\xf1Tk\xb3\n\xc6\xbb\x077\xb2\xa0\xe3\x13tb^\x83S&j`|A\x99\xb8\xf1\x0c'
Receive: 57 4000.460879 4000.459936 49: seq: 1a, identify_response offset=2280 data='$G3?\xa0\xf7\xd1\x9c\x01\xf7\xacQQ\x1d\x0f\x11,d;!\xab\xa4>\xf2kL\x9b\x1b\xe6#\xf5\xd4\xd7\x91\x9f\xedhp\x167'
Receive: 58 4000.462253 4000.461309 49: seq: 1b, identify_response offset=2320 data='\xaaIV~2r\x80x\xdf@3\xb9;&\x11\x0e^\xe0\xa5S?jH\xad\xf2}}\xcbk#\x94\x85\x9f&\x04\xa0n\xac\xc0\xc6'
Receive: 59 4000.463629 4000.462719 49: seq: 1c, identify_response offset=2360 data='p\x8e\xa0\x88\xd4\xcbC\x8c\xeb\x1b#\x92p\xfa`^e\x8dl\xc8s\x9a\xc0\xe2h\x07\x90\x01\xa9p\xd0\x95`\x83\xe8\xa3\x95\x1d\x08\x9c'
Receive: 60 4000.465004 4000.464070 49: seq: 1d, identify_response offset=2400 data='\xa6\x12\x1f\xf6F\x7f\xf6\xc8\x19\x95c]O\xf5Q2\xe5\xe2L{\xc5\xe8\xa12?\xfa\x0b+`\xe6\xbb\x9dQ+\xc4\xb3\x12h\x93\x93'
Receive: 61 4000.466379 4000.465442 49: seq: 1e, identify_response offset=2440 data='\xf5\xc8G\x0f\x9f{\xd2p\x07\x8e\x8a\xac%\x1f4N\xf0\x8f\x9d\x11\xf1\xbe\x0e[\x1eo\ty\xe6\xfa\xaf\x93\xe3\xb5\xc0\xc8W\xd4\xc6P'
Receive: 62 4000.467755 4000.466818 49: seq: 1f, identify_response offset=2480 data='\r\xb7W\xbb=Y\xa2\xf7\x809\x04\x08\xf3\x1fEP\xa8?b\xf7p>=\x8b\xe3\xf5\xd9n\xb5\xbe\x9foe\x9eM^\xff\x07gA'
Receive: 63 4000.469127 4000.468191 11: seq: 10, identify_response offset=2520 data='\xc2p'
Receive: 64 4000.470503 4000.469558 9: seq: 11, identify_response offset=2522 data=''
Receive: 65 4000.488168 4000.486951 12: seq: 12, uptime high=0 clock=698699443
Receive: 66 4000.540765 4000.539431 11: seq: 13, clock clock=704996214
Receive: 67 4000.592137 4000.591545 11: seq: 14, clock clock=711247274
Receive: 68 4000.643508 4000.643144 11: seq: 15, clock clock=717439124
Receive: 69 4000.694879 4000.694167 11: seq: 16, clock clock=723560854
Receive: 70 4000.747512 4000.746422 11: seq: 17, clock clock=729834284
Receive: 71 4000.798889 4000.798580 11: seq: 18, clock clock=736093094
Receive: 72 4000.850254 4000.849640 11: seq: 19, clock clock=742217614
Receive: 73 4000.901633 4000.901267 11: seq: 1a, clock clock=748412389
Receive: 74 4000.904323 4000.903874 10: seq: 1b, config is_config=0 crc=0 is_shutdown=0 move_count=0
Receive: 75 4000.905694 4000.904612 11: seq: 1c, clock clock=748816644
Receive: 76 4000.928911 4000.927943 15: seq: 1f, config is_config=1 crc=2351459781 is_shutdown=0 move_count=1024
Receive: 77 4000.941565 4000.940864 8: seq: 10, stepper_position oid=0 pos=0
Receive: 78 4000.944189 4000.943654 8: seq: 11, stepper_position oid=3 pos=0
Receive: 79 4000.946818 4000.945632 8: seq: 12, stepper_position oid=6 pos=0
Receive: 80 4000.949443 4000.948136 8: seq: 13, stepper_position oid=9 pos=0
Receive: 81 4000.952081 4000.951152 8: seq: 14, stepper_position oid=10 pos=0
Receive: 82 4001.782252 4000.951152 15: seq: 14, analog_in_state oid=11 next_clock=889200000 value=31553
Receive: 83 4001.862434 4000.951152 15: seq: 14, analog_in_state oid=19 next_clock=898800000 value=31580
Receive: 84 4001.889972 4001.888894 11: seq: 15, clock clock=866929679
Receive: 85 4002.082685 4001.888894 15: seq: 15, analog_in_state oid=11 next_clock=925200000 value=31549
Receive: 86 4002.162772 4001.888894 15: seq: 15, analog_in_state oid=19 next_clock=934800000 value=31582
Receive: 87 4002.382802 4001.888894 15: seq: 15, analog_in_state oid=11 next_clock=961200000 value=31552
Receive: 88 4002.462895 4001.888894 15: seq: 15, analog_in_state oid=19 next_clock=970800000 value=31580
Receive: 89 4002.683068 4001.888894 15: seq: 15, analog_in_state oid=11 next_clock=997200000 value=31550
Receive: 90 4002.763172 4001.888894 12: seq: 15, shutdown clock=971672284 static_string_id=ADC out of range
Transition to shutdown state: MCU 'mcu' shutdown: ADC out of range
This generally occurs when a heater temperature exceeds
its configured min_temp or max_temp.
Dumping gcode input 0 blocks
Dumping 20 requests for client 1967786184
Received 4001.119024: {"id": 1731449488, "method": "register_remote_method", "params": {"response_template": {"method": "pause_job_queue"}, "remote_method": "pause_job_queue"}}
Received 4001.123378: {"id": 1731449488, "method": "register_remote_method", "params": {"response_template": {"method": "start_job_queue"}, "remote_method": "start_job_queue"}}
Received 4001.131899: {"id": 1731815920, "method": "objects/query", "params": {"objects": {"heaters": null}}}
Received 4001.132986: {"id": 1731815408, "method": "objects/query", "params": {"objects": {"heaters": null}}}
Received 4001.141671: {"id": 1731816208, "method": "info", "params": {}}
Received 4001.142766: {"id": 1731936400, "method": "objects/list", "params": {}}
Received 4001.142766: {"id": 1731936336, "method": "gcode/help", "params": {}}
Received 4001.144620: {"id": 1721564688, "method": "info", "params": {}}
Received 4001.144620: {"id": 1721563760, "method": "objects/list", "params": {}}
Received 4001.144620: {"id": 1721563952, "method": "gcode/help", "params": {}}
Received 4001.169145: {"id": 1731936336, "method": "info", "params": {}}
Received 4001.169145: {"id": 1731815216, "method": "objects/list", "params": {}}
Received 4001.170993: {"id": 1731451440, "method": "gcode/help", "params": {}}
Received 4001.186217: {"id": 1731816080, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 4001.192266: {"id": 1731938000, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 4001.256027: {"id": 1721563792, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 4001.373223: {"id": 1731815152, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 4001.374397: {"id": 1731815408, "method": "objects/subscribe", "params": {"objects": {"webhooks": null, "print_stats": null, "heater_bed": null, "extruder": null, "configfile": null, "mcu": null, "heaters": null, "fan": null, "heater_fan my_nozzle_fan": null, "gcode_move": null, "bed_mesh": null, "motion_report": null, "query_endstops": null, "idle_timeout": null, "system_stats": null, "toolhead": null}, "response_template": {"method": "process_status_update"}}}
Received 4001.615653: {"id": 1731656560, "method": "list_endpoints", "params": {}}
Received 4002.713297: {"id": 1731655568, "method": "info", "params": {}}
gcode state: absolute_coord=True absolute_extrude=True base_position=[0.0, 0.0, 0.0, 0.0] last_position=[0.0, 0.0, 0.0, 0.0] homing_position=[0.0, 0.0, 0.0, 0.0] speed_factor=0.0166666666667 extrude_factor=1.0 speed=25.0
Reactor garbage collection: (4001.362193004, 0.0, 0.0)
Stats 4003.0: gcodein=0 mcu: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1103 bytes_read=4014 bytes_retransmit=9 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119997221 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.20 cputime=76.508 memavail=764000 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4004.0: gcodein=0 mcu: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1109 bytes_read=4120 bytes_retransmit=9 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995988 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.19 cputime=76.526 memavail=763888 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4005.0: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=1115 bytes_read=4256 bytes_retransmit=9 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995828 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.19 cputime=76.544 memavail=764072 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4006.0: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=1121 bytes_read=4362 bytes_retransmit=9 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995580 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.19 cputime=76.564 memavail=763880 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4007.0: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=1127 bytes_read=4483 bytes_retransmit=9 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995556 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.19 cputime=76.583 memavail=763880 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4008.0: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=1133 bytes_read=4604 bytes_retransmit=9 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995507 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.19 cputime=76.604 memavail=764128 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4009.0: gcodein=0 mcu: mcu_awake=0.005 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=1139 bytes_read=4710 bytes_retransmit=9 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995483 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.17 cputime=76.622 memavail=763644 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4010.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1145 bytes_read=4845 bytes_retransmit=9 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995627 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.17 cputime=76.652 memavail=763632 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4011.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1151 bytes_read=4966 bytes_retransmit=9 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995732 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.17 cputime=76.673 memavail=763892 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4012.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1157 bytes_read=5072 bytes_retransmit=9 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995745 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.17 cputime=76.696 memavail=763904 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4013.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1163 bytes_read=5193 bytes_retransmit=9 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995759 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.17 cputime=76.721 memavail=763888 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4014.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1169 bytes_read=5314 bytes_retransmit=9 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995721 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.16 cputime=76.741 memavail=764104 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4015.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1175 bytes_read=5434 bytes_retransmit=9 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995736 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.16 cputime=76.764 memavail=764388 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4016.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1181 bytes_read=5555 bytes_retransmit=9 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995740 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.16 cputime=76.787 memavail=764628 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4017.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1187 bytes_read=5676 bytes_retransmit=9 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995725 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.16 cputime=76.805 memavail=764396 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4018.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1193 bytes_read=5782 bytes_retransmit=9 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995714 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.16 cputime=76.825 memavail=764136 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4019.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1199 bytes_read=5918 bytes_retransmit=9 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995712 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.15 cputime=76.848 memavail=763884 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4020.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1205 bytes_read=6038 bytes_retransmit=9 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995710 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.15 cputime=76.872 memavail=763632 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4021.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1211 bytes_read=6144 bytes_retransmit=9 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995691 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.15 cputime=76.891 memavail=763396 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4022.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1217 bytes_read=6280 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995695 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.15 cputime=76.912 memavail=763612 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4023.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1223 bytes_read=6386 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995694 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.15 cputime=76.934 memavail=763924 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4024.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1229 bytes_read=6492 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995696 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.13 cputime=76.956 memavail=763388 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4025.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1235 bytes_read=6642 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995682 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.13 cputime=76.974 memavail=763676 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4026.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1241 bytes_read=6748 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995666 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.13 cputime=76.991 memavail=763428 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4027.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1247 bytes_read=6854 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995672 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.13 cputime=77.014 memavail=763208 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4028.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1253 bytes_read=6990 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995665 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.13 cputime=77.035 memavail=763392 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4029.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1259 bytes_read=7096 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995659 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.12 cputime=77.054 memavail=762912 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4030.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1265 bytes_read=7214 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995670 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.12 cputime=77.077 memavail=763412 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4031.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1271 bytes_read=7341 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995669 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.12 cputime=77.101 memavail=763188 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4032.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1277 bytes_read=7441 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995672 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.12 cputime=77.122 memavail=763160 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4033.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1283 bytes_read=7547 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995675 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.12 cputime=77.145 memavail=763432 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4034.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1289 bytes_read=7683 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995671 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.11 cputime=77.167 memavail=763056 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4035.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1295 bytes_read=7789 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995671 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.11 cputime=77.191 memavail=763200 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4036.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1301 bytes_read=7909 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995680 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.11 cputime=77.210 memavail=763064 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4037.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1307 bytes_read=8045 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995679 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.11 cputime=77.233 memavail=763200 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4038.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1313 bytes_read=8151 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995669 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.11 cputime=77.250 memavail=762876 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4039.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1319 bytes_read=8257 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995664 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.268 memavail=762932 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4040.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1325 bytes_read=8393 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995656 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.287 memavail=762948 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4041.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1331 bytes_read=8513 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995656 heater_bed: target=0 temp=20.4 pwm=0.000 sysload=0.10 cputime=77.309 memavail=762936 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000
Stats 4042.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1337 bytes_read=8619 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995655 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.329 memavail=763068 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4043.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1343 bytes_read=8755 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995658 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.352 memavail=763196 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4044.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1349 bytes_read=8861 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995658 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.372 memavail=763388 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4045.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1355 bytes_read=8967 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995659 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.394 memavail=763204 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4046.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1361 bytes_read=9117 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995661 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.416 memavail=763204 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4047.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1367 bytes_read=9223 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995661 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.434 memavail=763188 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4048.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1373 bytes_read=9344 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995670 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.10 cputime=77.460 memavail=763956 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4049.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1379 bytes_read=9465 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995675 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.09 cputime=77.474 memavail=763436 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4050.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1385 bytes_read=9571 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995689 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.09 cputime=77.497 memavail=763968 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4051.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1391 bytes_read=9706 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995697 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.09 cputime=77.524 memavail=764208 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4052.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1397 bytes_read=9827 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995695 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.09 cputime=77.544 memavail=763956 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Stats 4053.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1403 bytes_read=9933 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995690 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.09 cputime=77.561 memavail=764216 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000
Stats 4054.0: gcodein=0 mcu: mcu_awake=0.001 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=1409 bytes_read=10054 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 stalled_bytes=0 freq=119995685 heater_bed: target=0 temp=20.5 pwm=0.000 sysload=0.08 cputime=77.587 memavail=764232 print_time=0.001 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000
Attempting MCU 'mcu' reset command
webhooks client 1967786184: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:46:42 2022 (1642387602.1 4123.5)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 0
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968681368: New connection
webhooks client 1968681368: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968681368: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:48:58 2022 (1642387738.5 4260.0)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1967260656: New connection
webhooks client 1967260656: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1967260656: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:49:04 2022 (1642387744.3 4265.8)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1967261256: New connection
webhooks client 1967261256: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1967261256: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:49:26 2022 (1642387766.4 4287.9)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968646304: New connection
webhooks client 1968646304: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968646304: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:50:16 2022 (1642387816.4 4337.9)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968193008: New connection
webhooks client 1968193008: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968193008: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:50:46 2022 (1642387846.2 4367.7)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968162376: New connection
webhooks client 1968162376: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968162376: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:50:50 2022 (1642387850.5 4372.0)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968681808: New connection
webhooks client 1968681808: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968681808: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:50:59 2022 (1642387859.2 4380.6)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1968164016: New connection
webhooks client 1968164016: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968164016: Disconnected
webhooks client 1968147712: New connection
webhooks client 1968147712: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1968147712: Disconnected
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon Jan 17 02:51:38 2022 (1642387898.0 21.8)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1970880960: New connection
webhooks client 1970880960: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970880960: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:51:45 2022 (1642387905.8 29.6)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ mcu ]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1970935168: New connection
webhooks client 1970935168: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970935168: Disconnected
Restarting printer
Start printer at Mon Jan 17 02:57:14 2022 (1642388234.7 347.1)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 32
rotation_distance = 40
endstop_pin = tmc2209_stepper_x:virtual_endstop
position_endstop = -3
position_min = -3
position_max = 330
homing_speed = 60
homing_retract_dist = 0

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 32
rotation_distance = 40
position_max = 330
homing_speed = 60
homing_retract_dist = 0
endstop_pin = tmc2209_stepper_y:virtual_endstop
position_endstop = -3
position_min = -3

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -8

[extruder]
step_pin = P2.13
dir_pin = P0.11
enable_pin = !P2.12
microsteps = 32
rotation_distance = 22.478
gear_ratio = 66:22
pressure_advance = 0.6264
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = ATC Semitec 104GT-2
sensor_pin = P0.24
min_temp = 0
max_temp = 250
max_extrude_only_distance = 300

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 0
max_temp = 130

[fan]
pin = P2.3
max_power = 1

[tmc2209 stepper_x]
uart_pin = P1.10
diag_pin = P1.29
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2209 stepper_y]
uart_pin = P1.9
diag_pin = P1.28
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 999999

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 0

[controller_fan drivers_fan]
pin = P2.4

[safe_z_home]
home_xy_position = 165,165
speed = 50
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 50,5
screw2 = 165,5
screw3 = 325,5
screw4 = 5,325
screw5 = 165,325
screw6 = 325,325

[bed_mesh]
speed = 120
probe_count = 10,10
horizontal_move_z = 8
algorithm = lagrange
mesh_min = 20,20
mesh_max = 310,310
mesh_pps = 0

[probe]
x_offset = -40
y_offset = 0
pin = !P1.27
speed = 30

[gcode_arcs]
resolution = 1.0

[gcode_macro G29]
gcode = 
	BED_MESH_CALIBRATE
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 28, in load_config
    return PrinterHeaterBed(config)
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 11, in __init__
    self.heater = pheaters.setup_heater(config, 'B')
  File "/home/pi/klipper/klippy/extras/heaters.py", line 265, in setup_heater
    self.heaters[heater_name] = heater = Heater(config, sensor)
  File "/home/pi/klipper/klippy/extras/heaters.py", line 47, in __init__
    algo = config.getchoice('control', algos)
  File "/home/pi/klipper/klippy/configfile.py", line 75, in getchoice
    c = self.get(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'control' in section 'heater_bed' must be specified
webhooks client 1970921920: New connection
webhooks client 1970921920: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:57:23 2022 (1642388243.4 355.8)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 32
rotation_distance = 40
endstop_pin = tmc2209_stepper_x:virtual_endstop
position_endstop = -3
position_min = -3
position_max = 330
homing_speed = 60
homing_retract_dist = 0

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 32
rotation_distance = 40
position_max = 330
homing_speed = 60
homing_retract_dist = 0
endstop_pin = tmc2209_stepper_y:virtual_endstop
position_endstop = -3
position_min = -3

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -8

[extruder]
step_pin = P2.13
dir_pin = P0.11
enable_pin = !P2.12
microsteps = 32
rotation_distance = 22.478
gear_ratio = 66:22
pressure_advance = 0.6264
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = ATC Semitec 104GT-2
sensor_pin = P0.24
min_temp = 0
max_temp = 250
max_extrude_only_distance = 300

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 0
max_temp = 130

[fan]
pin = P2.3
max_power = 1

[tmc2209 stepper_x]
uart_pin = P1.10
diag_pin = P1.29
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2209 stepper_y]
uart_pin = P1.9
diag_pin = P1.28
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 999999

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 0

[controller_fan drivers_fan]
pin = P2.4

[safe_z_home]
home_xy_position = 165,165
speed = 50
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 50,5
screw2 = 165,5
screw3 = 325,5
screw4 = 5,325
screw5 = 165,325
screw6 = 325,325

[bed_mesh]
speed = 120
probe_count = 10,10
horizontal_move_z = 8
algorithm = lagrange
mesh_min = 20,20
mesh_max = 310,310
mesh_pps = 0

[probe]
x_offset = -40
y_offset = 0
pin = !P1.27
speed = 30

[gcode_arcs]
resolution = 1.0

[gcode_macro G29]
gcode = 
	BED_MESH_CALIBRATE
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 28, in load_config
    return PrinterHeaterBed(config)
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 11, in __init__
    self.heater = pheaters.setup_heater(config, 'B')
  File "/home/pi/klipper/klippy/extras/heaters.py", line 265, in setup_heater
    self.heaters[heater_name] = heater = Heater(config, sensor)
  File "/home/pi/klipper/klippy/extras/heaters.py", line 47, in __init__
    algo = config.getchoice('control', algos)
  File "/home/pi/klipper/klippy/configfile.py", line 75, in getchoice
    c = self.get(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'control' in section 'heater_bed' must be specified
webhooks client 1970069296: New connection
webhooks client 1970069296: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:57:40 2022 (1642388260.8 373.2)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 32
rotation_distance = 40
endstop_pin = tmc2209_stepper_x:virtual_endstop
position_endstop = -3
position_min = -3
position_max = 330
homing_speed = 60
homing_retract_dist = 0

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 32
rotation_distance = 40
position_max = 330
homing_speed = 60
homing_retract_dist = 0
endstop_pin = tmc2209_stepper_y:virtual_endstop
position_endstop = -3
position_min = -3

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -8

[extruder]
step_pin = P2.13
dir_pin = P0.11
enable_pin = !P2.12
microsteps = 32
rotation_distance = 22.478
gear_ratio = 66:22
pressure_advance = 0.6264
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = ATC Semitec 104GT-2
sensor_pin = P0.24
min_temp = 0
max_temp = 250
max_extrude_only_distance = 300

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 2
max_temp = 130

[fan]
pin = P2.3
max_power = 1

[tmc2209 stepper_x]
uart_pin = P1.10
diag_pin = P1.29
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2209 stepper_y]
uart_pin = P1.9
diag_pin = P1.28
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 999999

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 0

[controller_fan drivers_fan]
pin = P2.4

[safe_z_home]
home_xy_position = 165,165
speed = 50
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 50,5
screw2 = 165,5
screw3 = 325,5
screw4 = 5,325
screw5 = 165,325
screw6 = 325,325

[bed_mesh]
speed = 120
probe_count = 10,10
horizontal_move_z = 8
algorithm = lagrange
mesh_min = 20,20
mesh_max = 310,310
mesh_pps = 0

[probe]
x_offset = -40
y_offset = 0
pin = !P1.27
speed = 30

[gcode_arcs]
resolution = 1.0

[gcode_macro G29]
gcode = 
	BED_MESH_CALIBRATE
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 28, in load_config
    return PrinterHeaterBed(config)
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 11, in __init__
    self.heater = pheaters.setup_heater(config, 'B')
  File "/home/pi/klipper/klippy/extras/heaters.py", line 265, in setup_heater
    self.heaters[heater_name] = heater = Heater(config, sensor)
  File "/home/pi/klipper/klippy/extras/heaters.py", line 47, in __init__
    algo = config.getchoice('control', algos)
  File "/home/pi/klipper/klippy/configfile.py", line 75, in getchoice
    c = self.get(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'control' in section 'heater_bed' must be specified
webhooks client 1970899504: New connection
webhooks client 1970899504: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:58:04 2022 (1642388284.6 397.0)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 32
rotation_distance = 40
endstop_pin = tmc2209_stepper_x:virtual_endstop
position_endstop = -3
position_min = -3
position_max = 330
homing_speed = 60
homing_retract_dist = 0

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 32
rotation_distance = 40
position_max = 330
homing_speed = 60
homing_retract_dist = 0
endstop_pin = tmc2209_stepper_y:virtual_endstop
position_endstop = -3
position_min = -3

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -8

[extruder]
step_pin = P2.13
dir_pin = P0.11
enable_pin = !P2.12
microsteps = 32
rotation_distance = 22.478
gear_ratio = 66:22
pressure_advance = 0.6264
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = ATC Semitec 104GT-2
sensor_pin = P0.24
min_temp = 0
max_temp = 250
max_extrude_only_distance = 300

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 2
max_temp = 130

[fan]
pin = P2.3
max_power = 1

[tmc2209 stepper_x]
uart_pin = P1.10
diag_pin = P1.29
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2209 stepper_y]
uart_pin = P1.9
diag_pin = P1.28
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 999999

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 0

[controller_fan drivers_fan]
pin = P2.4

[safe_z_home]
home_xy_position = 165,165
speed = 50
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 50,5
screw2 = 165,5
screw3 = 325,5
screw4 = 5,325
screw5 = 165,325
screw6 = 325,325

[bed_mesh]
speed = 120
probe_count = 10,10
horizontal_move_z = 8
algorithm = lagrange
mesh_min = 20,20
mesh_max = 310,310
mesh_pps = 0

[probe]
x_offset = -40
y_offset = 0
pin = !P1.27
speed = 30

[gcode_arcs]
resolution = 1.0

[gcode_macro G29]
gcode = 
	BED_MESH_CALIBRATE
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 28, in load_config
    return PrinterHeaterBed(config)
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 11, in __init__
    self.heater = pheaters.setup_heater(config, 'B')
  File "/home/pi/klipper/klippy/extras/heaters.py", line 265, in setup_heater
    self.heaters[heater_name] = heater = Heater(config, sensor)
  File "/home/pi/klipper/klippy/extras/heaters.py", line 47, in __init__
    algo = config.getchoice('control', algos)
  File "/home/pi/klipper/klippy/configfile.py", line 75, in getchoice
    c = self.get(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'control' in section 'heater_bed' must be specified
webhooks client 1970046936: New connection
webhooks client 1970046936: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:58:09 2022 (1642388289.8 402.2)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 32
rotation_distance = 40
endstop_pin = tmc2209_stepper_x:virtual_endstop
position_endstop = -3
position_min = -3
position_max = 330
homing_speed = 60
homing_retract_dist = 0

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 32
rotation_distance = 40
position_max = 330
homing_speed = 60
homing_retract_dist = 0
endstop_pin = tmc2209_stepper_y:virtual_endstop
position_endstop = -3
position_min = -3

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_max = 400
position_min = -8

[extruder]
step_pin = P2.13
dir_pin = P0.11
enable_pin = !P2.12
microsteps = 32
rotation_distance = 22.478
gear_ratio = 66:22
pressure_advance = 0.6264
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = ATC Semitec 104GT-2
sensor_pin = P0.24
min_temp = 0
max_temp = 250
max_extrude_only_distance = 300

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 2
max_temp = 130

[fan]
pin = P2.3
max_power = 1

[tmc2209 stepper_x]
uart_pin = P1.10
diag_pin = P1.29
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2209 stepper_y]
uart_pin = P1.9
diag_pin = P1.28
run_current = 0.950
hold_current = 0.500
driver_sgthrs = 130

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 999999

[tmc2209 extruder]
uart_pin = P1.4
run_current = 0.950
hold_current = 0.500
stealthchop_threshold = 0

[controller_fan drivers_fan]
pin = P2.4

[safe_z_home]
home_xy_position = 165,165
speed = 50
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 50,5
screw2 = 165,5
screw3 = 325,5
screw4 = 5,325
screw5 = 165,325
screw6 = 325,325

[bed_mesh]
speed = 120
probe_count = 10,10
horizontal_move_z = 8
algorithm = lagrange
mesh_min = 20,20
mesh_max = 310,310
mesh_pps = 0

[probe]
x_offset = -40
y_offset = 0
pin = !P1.27
speed = 30

[gcode_arcs]
resolution = 1.0

[gcode_macro G29]
gcode = 
	BED_MESH_CALIBRATE
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 28, in load_config
    return PrinterHeaterBed(config)
  File "/home/pi/klipper/klippy/extras/heater_bed.py", line 11, in __init__
    self.heater = pheaters.setup_heater(config, 'B')
  File "/home/pi/klipper/klippy/extras/heaters.py", line 265, in setup_heater
    self.heaters[heater_name] = heater = Heater(config, sensor)
  File "/home/pi/klipper/klippy/extras/heaters.py", line 47, in __init__
    algo = config.getchoice('control', algos)
  File "/home/pi/klipper/klippy/configfile.py", line 75, in getchoice
    c = self.get(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'control' in section 'heater_bed' must be specified
webhooks client 1970942000: New connection
webhooks client 1970942000: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:59:14 2022 (1642388354.1 466.5)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_accel_to_decel = 7000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 274, in load_config
    blt = BLTouchEndstopWrapper(config)
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 33, in __init__
    self.position_endstop = config.getfloat('z_offset', minval=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'z_offset' in section 'bltouch' must be specified
webhooks client 1970237768: New connection
webhooks client 1970237768: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:59:34 2022 (1642388374.2 486.6)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_accel_to_decel = 7000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 274, in load_config
    blt = BLTouchEndstopWrapper(config)
  File "/home/pi/klipper/klippy/extras/bltouch.py", line 33, in __init__
    self.position_endstop = config.getfloat('z_offset', minval=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'z_offset' in section 'bltouch' must be specified
webhooks client 1971071016: New connection
webhooks client 1971071016: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 02:59:51 2022 (1642388391.1 503.5)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_accel_to_decel = 7000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
z_offset = 2
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 60
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1970069216: New connection
webhooks client 1970069216: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 03:01:16 2022 (1642388476.1 588.5)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_accel_to_decel = 7000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
z_offset = 2
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
default_parameter_bed_temp = 55
default_parameter_extruder_temp = 200
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84
=======================
Extruder max_extrude_ratio=0.266081
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 145, in _read_config
    pconfig.check_unused_options(config)
  File "/home/pi/klipper/klippy/configfile.py", line 300, in check_unused_options
    % (option, section))
Error: Option 'default_parameter_bed_temp' is not valid in section 'gcode_macro start_print'
webhooks client 1970900304: New connection
webhooks client 1970900304: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 03:01:32 2022 (1642388492.3 604.7)
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = cartesian
max_velocity = 250
max_accel = 3000
max_accel_to_decel = 7000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[skew_correction]

[stepper_x]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_y]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 300
homing_speed = 100

[stepper_z]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = probe:z_virtual_endstop
position_min = -2
position_max = 400

[stepper_z1]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 7
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[heater_fan my_nozzle_fan]
pin = P2.4
heater = extruder
heater_temp = 50.0
fan_speed = 1.0

[bltouch]
sensor_pin = P0.10
control_pin = P2.0
x_offset = 28
y_offset = -35
z_offset = 2
samples = 2
samples_result = average
probe_with_touch_mode = true
stow_on_each_sample = false

[safe_z_home]
home_xy_position = 122,183
speed = 150
z_hop = 10
z_hop_speed = 5

[bed_screws]
screw1 = 55,55
screw1_name = front left
screw2 = 255,55
screw2_name = front right
screw3 = 255,255
screw3_name = back right
screw4 = 55,255
screw4_name = back left
speed = 100.0

[screws_tilt_adjust]
screw1 = 22,83
screw1_name = front left
screw2 = 222,83
screw2_name = front right
screw3 = 22,283
screw3_name = back left
screw4 = 222,283
screw4_name = back right
speed = 100.0
screw_thread = CW-M5

[bed_mesh]
speed = 800
mesh_min = 30,30
mesh_max = 270,270
probe_count = 5,5
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = 0.2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0

[gcode_macro START_PRINT]
gcode = 
	G28
	G29
	G90
	G1 X0 Y0 Z5 F3000
	G1 Z0.15 F300
	G92 E0 ;Reset Extruder
	G1 X20 Y5 Z0.3 F5000.0
	G1 Z0.3 F1000
	G1 X200 Y5 F1500.0 E15
	G1 X200 Y5.3 Z0.3 F5000.0
	G1 X5.3  Y5.3 Z0.3 F1500.0 E30
	G1 Z3 F3000
	G21 ; set units to millimeters
	G90 ; use absolute coordinates
	M83 ; use relative	distances for extrusion
	G92 E0

[gcode_macro END_PRINT]
gcode = 
	M140 S0
	M104 S0
	M106 S0
	G91
	G1 X-2 Y-2 E-3 F300
	G1 Z30 F3000
	G90
	M84
=======================
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
webhooks client 1968112664: New connection
webhooks client 1968112664: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
mcu 'mcu': Unable to open serial port: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 03:02:26 2022 (1642388546.5 658.9)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5

[ bed_mesh ]
geschwindigkeit = 800
mesh_min = 30,30
mesh_max = 270.270
probe_count = 5,5
mesh_pps = 2,2
algorithmus = bikubisch
bicubic_tension = 0,2
move_check_distance = 3.0
split_delta_z = .010
fade_start = 1.0
fade_end = 5.0
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1229, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 94, in __init__
    self.bmc = BedMeshCalibrate(config, self)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 291, in __init__
    self._init_mesh_config(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 429, in _init_mesh_config
    max_x, max_y = config.getfloatlist('mesh_max', count=2)
  File "/home/pi/klipper/klippy/configfile.py", line 107, in getfloatlist
    parser=float, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 95, in getlists
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 35, in _get_wrapper
    v = parser(self.section, option)
  File "/home/pi/klipper/klippy/configfile.py", line 93, in fcparser
    return lparser(self.fileconfig.get(section, option), len(seps) - 1)
  File "/home/pi/klipper/klippy/configfile.py", line 90, in lparser
    % (option, self.section, count))
Error: Option 'mesh_max' in section ' bed_mesh ' must have 2 elements
webhooks client 1968333288: New connection
webhooks client 1968333288: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 03:02:45 2022 (1642388565.4 677.8)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/corexy.py", line 100, in load_kinematics
    return CoreXYKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/corexy.py", line 12, in __init__
    self.rails = [ stepper.PrinterRail(config.getsection('stepper_x')),
  File "/home/pi/klipper/klippy/stepper.py", line 283, in __init__
    self.add_extra_stepper(config)
  File "/home/pi/klipper/klippy/stepper.py", line 353, in add_extra_stepper
    stepper = PrinterStepper(config, self.stepper_units_in_radians)
  File "/home/pi/klipper/klippy/stepper.py", line 221, in PrinterStepper
    step_pin = config.get('step_pin')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'step_pin' in section 'stepper_x' must be specified
webhooks client 1971063864: New connection
webhooks client 1971063864: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon Jan 17 02:53:55 2022 (1642388035.0 20.9)
Can't read autosave from config file - autosave state corrupted
===== Config file =====
[mcu]
serial = dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00

[printer]
kinematics = corexy
max_velocity = 300
max_accel = 7000
max_accel_to_decel = 7000
max_z_velocity = 25
max_z_accel = 30

[skew_correction]

[stepper_x ]
step_pin = P2.2
dir_pin = !P2.6
enable_pin = !P2.1
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.29
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_y ]
step_pin = P0.19
dir_pin = !P0.20
enable_pin = !P2.8
mikroschritte = 16
rotationsabstand = 40
endstop_pin = !P1.28
position_endanschlag = 0
position_max = 300
homing_speed = 100

[ stepper_z ]
step_pin = P0.22
dir_pin = P2.11
enable_pin = !P0.21
mikroschritte = 16
rotationsabstand = 8
endstop_pin = P1.25
position_min = -2
position_max = 400
position_endstop = 0

[ stepper_z1 ]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
mikroschritte = 16
rotationsabstand = 8

[ Extruder ]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
mikroschritte = 16
rotationsabstand = 7
du sendurchmesser = 0,400
filamentdurchmesser = 1.750
heizungsstift = P2.7
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.24
steuerung = PID
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
max_extrude_only_distance = 100
min_temp = 190
max_temp = 260

[ heizung_bett ]
heizung_pin = P2.5
sensortyp = EPCOS 100K B57560G104F
sensor_pin = P0.25
min_temp = 5
max_temp = 130

[ Lüfter ]
stift = P2.3

[ Heizungslüfter mein_Düsenlüfter ]
stift = P2.4
heizung = Extruder
heizungstemp = 50,0
lüftergeschwindigkeit = 1,0

[ Drucker ]
kinematik = kartesisch
max_velocity = 250
max_accel = 3000
max_z_velocity = 20
max_z_accel = 100
square_corner_velocity = 5

[ Bettschrauben ]
schraube1 = 55,55
schraube1_name = vorne links
schraube2 = 255,55
screw2_name = vorne rechts
schraube3 = 255.255
screw3_name = hinten rechts
schraube4 = 55.255
screw4_name = hinten links
geschwindigkeit = 100,0

[ schrauben_neigung_einstellen ]
schraube1 = 22,83
schraube1_name = vorne links
schraube2 = 222,83
screw2_name = vorne rechts
schraube3 = 22.283
screw3_name = hinten links
schraube4 = 222.283
screw4_name = hinten rechts
geschwindigkeit = 100,0
schraubengewinde = CW-M5
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/corexy.py", line 100, in load_kinematics
    return CoreXYKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/corexy.py", line 12, in __init__
    self.rails = [ stepper.PrinterRail(config.getsection('stepper_x')),
  File "/home/pi/klipper/klippy/stepper.py", line 283, in __init__
    self.add_extra_stepper(config)
  File "/home/pi/klipper/klippy/stepper.py", line 353, in add_extra_stepper
    stepper = PrinterStepper(config, self.stepper_units_in_radians)
  File "/home/pi/klipper/klippy/stepper.py", line 221, in PrinterStepper
    step_pin = config.get('step_pin')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'step_pin' in section 'stepper_x' must be specified
webhooks client 1971929376: New connection
webhooks client 1971929376: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00: [Errno 2] No such file or directory: 'dev/serial/by-id/usb-Klipper_lpc1769_1EC0FF19871C4AAFD1697C5DC32000F5-if00'
Restarting printer
Start printer at Mon Jan 17 04:21:08 2022 (1642393268.3 530.3)
===== Config file =====

=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971983224: New connection
webhooks client 1971983224: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971983224: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:21:27 2022 (1642393287.6 549.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1971955832: New connection
webhooks client 1971955832: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/klipper_config/printer.cfg', '-l', '/home/pi/klipper_logs/klippy.log', '-a', '/tmp/klippy_uds']
Git version: 'v0.10.0-234-g02d5f975'
CPU: 4 core ARMv7 Processor rev 4 (v7l)
Python: '2.7.16 (default, Oct 10 2019, 22:02:15) \n[GCC 8.3.0]'
Start printer at Mon Jan 17 04:21:10 2022 (1642393270.6 21.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1970709408: New connection
webhooks client 1970709408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970709408: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:44:49 2022 (1642394689.1 40.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]

[tmc2208 stepper_y]

[tmc2208 stepper_z]

[tmc2208 extruder]

[tmc2208 extruder1]

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 189, in __init__
    self.mcu_tmc = tmc_uart.MCU_TMC_uart(config, Registers, self.fields)
  File "/home/pi/klipper/klippy/extras/tmc_uart.py", line 220, in __init__
    config, max_addr)
  File "/home/pi/klipper/klippy/extras/tmc_uart.py", line 191, in lookup_tmc_uart_bitbang
    rx_pin_params = ppins.lookup_pin(config.get('uart_pin'), can_pullup=True,
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'uart_pin' in section 'tmc2208 stepper_x' must be specified
webhooks client 1971178152: New connection
webhooks client 1971178152: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971178152: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:45:37 2022 (1642394737.7 89.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1970708848: New connection
webhooks client 1970708848: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970708848: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:47:12 2022 (1642394832.6 183.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1971376176: New connection
webhooks client 1971376176: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971376176: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:48:18 2022 (1642394898.5 249.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
step_distance = .010526
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder' must be specified
webhooks client 1971418176: New connection
webhooks client 1971418176: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971418176: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:48:40 2022 (1642394920.6 271.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
step_distance = .010526
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1971419096: New connection
webhooks client 1971419096: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971419096: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:49:51 2022 (1642394991.1 342.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1970816424: New connection
webhooks client 1970816424: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970816424: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:50:49 2022 (1642395049.7 401.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1971277872: New connection
webhooks client 1971277872: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971277872: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:51:36 2022 (1642395096.5 447.7)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 255, in _parse_config
    self._parse_config_buffer(buffer, filename, fileconfig)
  File "/home/pi/klipper/klippy/configfile.py", line 215, in _parse_config_buffer
    fileconfig.readfp(sbuffer, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 324, in readfp
    self._read(fp, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 546, in _read
    raise e
ParsingError: File contains parsing errors: /home/pi/klipper_config/printer.cfg
	[line 65]: '...\n'
webhooks client 1971172816: New connection
webhooks client 1971172816: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971172816: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:51:49 2022 (1642395109.0 460.3)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 255, in _parse_config
    self._parse_config_buffer(buffer, filename, fileconfig)
  File "/home/pi/klipper/klippy/configfile.py", line 215, in _parse_config_buffer
    fileconfig.readfp(sbuffer, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 324, in readfp
    self._read(fp, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 546, in _read
    raise e
ParsingError: File contains parsing errors: /home/pi/klipper_config/printer.cfg
	[line 65]: '...\n'
webhooks client 1971379856: New connection
webhooks client 1971379856: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971379856: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:51:52 2022 (1642395112.2 463.5)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 255, in _parse_config
    self._parse_config_buffer(buffer, filename, fileconfig)
  File "/home/pi/klipper/klippy/configfile.py", line 215, in _parse_config_buffer
    fileconfig.readfp(sbuffer, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 324, in readfp
    self._read(fp, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 546, in _read
    raise e
ParsingError: File contains parsing errors: /home/pi/klipper_config/printer.cfg
	[line 65]: '...\n'
webhooks client 1971171656: New connection
webhooks client 1971171656: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971171656: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:53:26 2022 (1642395206.3 557.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1971360472: New connection
webhooks client 1971360472: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971360472: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:54:48 2022 (1642395289.0 640.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 extruder1]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'extruder1' must be specified
webhooks client 1971376936: New connection
webhooks client 1971376936: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971376936: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:55:41 2022 (1642395341.1 692.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 400
max_accel = 500
max_z_velocity = 10
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970697960: New connection
webhooks client 1970697960: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970697960: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:57:31 2022 (1642395451.6 802.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
square_corner_velocity = 5
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 219, in __init__
    'square_corner_velocity', 5., minval=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'square_corner_velocity' in section 'printer'
webhooks client 1970233832: New connection
webhooks client 1970233832: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970233832: Disconnected
Restarting printer
Start printer at Mon Jan 17 04:58:31 2022 (1642395511.6 862.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971279152: New connection
webhooks client 1971279152: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971279152: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:00:21 2022 (1642395621.5 972.7)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 27, in __init__
    above=0., maxval=max_velocity)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_velocity' in section 'printer'
webhooks client 1970816264: New connection
webhooks client 1970816264: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970816264: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:01:28 2022 (1642395688.3 1039.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970525808: New connection
webhooks client 1970525808: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970525808: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:07:22 2022 (1642396042.1 1393.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 50
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971431544: New connection
webhooks client 1971431544: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971431544: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:08:04 2022 (1642396084.4 1435.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 50
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970527688: New connection
webhooks client 1970527688: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970527688: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:08:20 2022 (1642396100.4 1451.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 5
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971567392: New connection
webhooks client 1971567392: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971567392: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:08:38 2022 (1642396118.7 1470.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971165624: New connection
webhooks client 1971165624: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971165624: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:09:53 2022 (1642396193.7 1544.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 27, in __init__
    above=0., maxval=max_velocity)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_velocity' in section 'printer'
webhooks client 1971172896: New connection
webhooks client 1971172896: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971172896: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:14:05 2022 (1642396445.4 1796.7)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 213, in __init__
    self.max_velocity = config.getfloat('max_velocity', above=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'max_velocity' in section 'printer' must be specified
webhooks client 1971173336: New connection
webhooks client 1971173336: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
TMC2208 configuration: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00\nTMC2208 configuration'
Restarting printer
Start printer at Mon Jan 17 05:16:17 2022 (1642396577.9 1929.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971379856: New connection
webhooks client 1971379856: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971379856: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:19:09 2022 (1642396749.7 2101.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 50
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970467304: New connection
webhooks client 1970467304: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970467304: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:21:46 2022 (1642396907.0 2258.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 213, in __init__
    self.max_velocity = config.getfloat('max_velocity', above=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'max_velocity' in section 'printer' must be specified
webhooks client 1970435656: New connection
webhooks client 1970435656: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00
TMC2208 configuration: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00\nTMC2208 configuration'
Restarting printer
Start printer at Mon Jan 17 05:22:08 2022 (1642396928.4 2279.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970272376: New connection
webhooks client 1970272376: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970272376: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:22:45 2022 (1642396965.5 2316.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971449728: New connection
webhooks client 1971449728: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971449728: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:23:58 2022 (1642397038.6 2389.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'stepper_z' must be specified
webhooks client 1971279032: New connection
webhooks client 1971279032: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971279032: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:24:10 2022 (1642397050.8 2402.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 193, in __init__
    cmdhelper = tmc.TMCCommandHelper(config, self.mcu_tmc, current_helper)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 232, in __init__
    TMCMicrostepHelper(config, mcu_tmc)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 512, in TMCMicrostepHelper
    mres = ms_config.getchoice('microsteps', steps)
  File "/home/pi/klipper/klippy/configfile.py", line 73, in getchoice
    c = self.getint(option, default, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 62, in getint
    minval, maxval, note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'microsteps' in section 'stepper_z' must be specified
webhooks client 1970358752: New connection
webhooks client 1970358752: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970358752: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:24:20 2022 (1642397060.5 2411.7)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
microsteps = 16

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 223, in load_config_prefix
    return TMC2208(config)
  File "/home/pi/klipper/klippy/extras/tmc2208.py", line 200, in __init__
    tmc.TMCStealthchopHelper(config, self.mcu_tmc, TMC_FREQUENCY)
  File "/home/pi/klipper/klippy/extras/tmc.py", line 524, in TMCStealthchopHelper
    step_dist = stepper.parse_step_distance(stepper_config)
  File "/home/pi/klipper/klippy/stepper.py", line 257, in parse_step_distance
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'rotation_distance' in section 'stepper_z' must be specified
webhooks client 1970171336: New connection
webhooks client 1970171336: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970171336: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:24:40 2022 (1642397081.0 2432.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971378576: New connection
webhooks client 1971378576: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971378576: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:24:58 2022 (1642397098.2 2449.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 0
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970181744: New connection
webhooks client 1970181744: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970181744: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:26:12 2022 (1642397172.1 2523.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970254472: New connection
webhooks client 1970254472: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970254472: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:30:20 2022 (1642397420.6 2771.8)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971446008: New connection
webhooks client 1971446008: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971446008: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:31:10 2022 (1642397470.2 2821.4)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1970271696: New connection
webhooks client 1970271696: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970271696: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:31:29 2022 (1642397489.1 2840.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970200168: New connection
webhooks client 1970200168: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970200168: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:33:33 2022 (1642397613.3 2964.5)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 27, in __init__
    above=0., maxval=max_velocity)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_velocity' in section 'printer'
webhooks client 1970256632: New connection
webhooks client 1970256632: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970256632: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:33:42 2022 (1642397623.0 2974.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 214, in __init__
    self.max_accel = config.getfloat('max_accel', above=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_accel' in section 'printer'
webhooks client 1970257512: New connection
webhooks client 1970257512: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970257512: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:33:51 2022 (1642397632.0 2983.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 213, in __init__
    self.max_velocity = config.getfloat('max_velocity', above=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_velocity' in section 'printer'
webhooks client 1971448688: New connection
webhooks client 1971448688: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971448688: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:34:00 2022 (1642397640.1 2991.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 213, in __init__
    self.max_velocity = config.getfloat('max_velocity', above=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'max_velocity' in section 'printer' must be specified
webhooks client 1970525768: New connection
webhooks client 1970525768: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970525768: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:34:31 2022 (1642397671.2 3022.5)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 213, in __init__
    self.max_velocity = config.getfloat('max_velocity', above=0.)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'max_velocity' in section 'printer' must be specified
webhooks client 1970436296: New connection
webhooks client 1970436296: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970436296: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:38:50 2022 (1642397930.1 3281.3)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 255, in _parse_config
    self._parse_config_buffer(buffer, filename, fileconfig)
  File "/home/pi/klipper/klippy/configfile.py", line 215, in _parse_config_buffer
    fileconfig.readfp(sbuffer, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 324, in readfp
    self._read(fp, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 512, in _read
    raise MissingSectionHeaderError(fpname, lineno, line)
MissingSectionHeaderError: File contains no section headers.
file: /home/pi/klipper_config/printer.cfg, line: 1
'lib reddit. v0.21.7\n'
webhooks client 1970371200: New connection
webhooks client 1970371200: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970371200: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:39:13 2022 (1642397953.1 3304.4)
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 276, in read_main_config
    regular_config = self._build_config_wrapper(regular_data, filename)
  File "/home/pi/klipper/klippy/configfile.py", line 263, in _build_config_wrapper
    self._parse_config(data, filename, fileconfig, set())
  File "/home/pi/klipper/klippy/configfile.py", line 255, in _parse_config
    self._parse_config_buffer(buffer, filename, fileconfig)
  File "/home/pi/klipper/klippy/configfile.py", line 215, in _parse_config_buffer
    fileconfig.readfp(sbuffer, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 324, in readfp
    self._read(fp, filename)
  File "/usr/lib/python2.7/ConfigParser.py", line 546, in _read
    raise e
ParsingError: File contains parsing errors: /home/pi/klipper_config/printer.cfg
	[line 233]: '5\n'
	[line 234]: 'Dauerlink\n'
	[line 235]: 'reddit\n'
	[line 236]: '100% positiv bewertet\n'
	[line 239]: 'Vertrauen\n'
	[line 241]: '1\n'
	[line 243]: 'u/jourgen4 24. April 21\n'
	[line 244]: 'Sch\xc3\xb6n! Haben Sie irgendwelche Vorteile von Switching Boards gesehen? Frage da ich \xc3\xbcberlege auf den SKR 1.4 Turbo umzusteigen. Ich habe gerade eine rumliegen und m\xc3\xb6chte wissen, ob es die M\xc3\xbche wert ist.\n'
	[line 246]: '1\n'
	[line 248]: 'u/thepirho 24. April 21\n'
	[line 249]: 'Hotend-Mosfet ist auf der Standardplatine gestorben, Klipper ist viel schneller und einfacher zu konfigurieren\n'
	[line 251]: '1\n'
	[line 253]: 'u/YoMommaJokeBot 24. April 21\n'
	[line 254]: 'Nicht so schnell wie deine Mama\n'
	[line 256]: 'Ich bin ein Bot. Zum Entfernen ablehnen . PM an mich, wenn es etwas f\xc3\xbcr mich zu wissen gibt!'
webhooks client 1972068600: New connection
webhooks client 1972068600: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Transition to shutdown state: Shutdown due to webhooks request
Dumping 20 requests for client 1972068600
Received 3581.365322: {"id": 1732058192, "method": "info", "params": {}}
Received 3582.173071: {"id": 1740713776, "method": "info", "params": {}}
Received 3583.131085: {"id": 1731688752, "method": "info", "params": {}}
Received 3583.366636: {"id": 1731690448, "method": "info", "params": {}}
Received 3584.173129: {"id": 1731686672, "method": "info", "params": {}}
Received 3585.129038: {"id": 1731689936, "method": "info", "params": {}}
Received 3585.364844: {"id": 1731690480, "method": "info", "params": {}}
Received 3586.172716: {"id": 1731688848, "method": "info", "params": {}}
Received 3587.129494: {"id": 1731690000, "method": "info", "params": {}}
Received 3587.364532: {"id": 1731687600, "method": "info", "params": {}}
Received 3588.172566: {"id": 1731686608, "method": "info", "params": {}}
Received 3589.130976: {"id": 1731690000, "method": "info", "params": {}}
Received 3589.366558: {"id": 1731687600, "method": "info", "params": {}}
Received 3590.171167: {"id": 1731690128, "method": "info", "params": {}}
Received 3591.131063: {"id": 1731687600, "method": "info", "params": {}}
Received 3591.366505: {"id": 1731686960, "method": "info", "params": {}}
Received 3592.170968: {"id": 1740712496, "method": "info", "params": {}}
Received 3593.131157: {"id": 1731736144, "method": "info", "params": {}}
Received 3593.365906: {"id": 1955082384, "method": "info", "params": {}}
Received 3593.856955: {"id": 1731737072, "method": "emergency_stop", "params": {}}
Reactor garbage collection: (3558.777886559, 3585.365790871, 0.0)
webhooks client 1972068600: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:44:05 2022 (1642398245.9 3597.2)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971410864: New connection
webhooks client 1971410864: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971410864: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:44:22 2022 (1642398262.1 3613.4)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970436136: New connection
webhooks client 1970436136: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970436136: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:46:54 2022 (1642398414.6 3765.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971448088: New connection
webhooks client 1971448088: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971448088: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:54:10 2022 (1642398850.4 4201.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970852368: New connection
webhooks client 1970852368: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970852368: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:54:23 2022 (1642398863.4 4214.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases =
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971419296: New connection
webhooks client 1971419296: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971419296: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:55:19 2022 (1642398919.4 4270.7)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1 header
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2 header
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
	Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
	See the sample-lcd.cfg file for definitions of common LCD displays.
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/board_pins.py", line 24, in load_config
    return PrinterBoardAliases(config)
  File "/home/pi/klipper/klippy/extras/board_pins.py", line 14, in __init__
    aliases = config.getlists(opt, seps=('=', ','), count=2)
  File "/home/pi/klipper/klippy/configfile.py", line 95, in getlists
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 35, in _get_wrapper
    v = parser(self.section, option)
  File "/home/pi/klipper/klippy/configfile.py", line 93, in fcparser
    return lparser(self.fileconfig.get(section, option), len(seps) - 1)
  File "/home/pi/klipper/klippy/configfile.py", line 86, in lparser
    return tuple([lparser(p, pos - 1) for p in parts if p])
  File "/home/pi/klipper/klippy/configfile.py", line 90, in lparser
    % (option, self.section, count))
Error: Option 'aliases' in section 'board_pins' must have 2 elements
webhooks client 1970256712: New connection
webhooks client 1970256712: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970256712: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:55:40 2022 (1642398940.6 4291.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1 header
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2 header
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
	Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/board_pins.py", line 24, in load_config
    return PrinterBoardAliases(config)
  File "/home/pi/klipper/klippy/extras/board_pins.py", line 14, in __init__
    aliases = config.getlists(opt, seps=('=', ','), count=2)
  File "/home/pi/klipper/klippy/configfile.py", line 95, in getlists
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 35, in _get_wrapper
    v = parser(self.section, option)
  File "/home/pi/klipper/klippy/configfile.py", line 93, in fcparser
    return lparser(self.fileconfig.get(section, option), len(seps) - 1)
  File "/home/pi/klipper/klippy/configfile.py", line 86, in lparser
    return tuple([lparser(p, pos - 1) for p in parts if p])
  File "/home/pi/klipper/klippy/configfile.py", line 90, in lparser
    % (option, self.section, count))
Error: Option 'aliases' in section 'board_pins' must have 2 elements
webhooks client 1971446888: New connection
webhooks client 1971446888: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971446888: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:55:54 2022 (1642398954.3 4305.5)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1 header
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
	Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 141, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 130, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/board_pins.py", line 24, in load_config
    return PrinterBoardAliases(config)
  File "/home/pi/klipper/klippy/extras/board_pins.py", line 14, in __init__
    aliases = config.getlists(opt, seps=('=', ','), count=2)
  File "/home/pi/klipper/klippy/configfile.py", line 95, in getlists
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 35, in _get_wrapper
    v = parser(self.section, option)
  File "/home/pi/klipper/klippy/configfile.py", line 93, in fcparser
    return lparser(self.fileconfig.get(section, option), len(seps) - 1)
  File "/home/pi/klipper/klippy/configfile.py", line 86, in lparser
    return tuple([lparser(p, pos - 1) for p in parts if p])
  File "/home/pi/klipper/klippy/configfile.py", line 90, in lparser
    % (option, self.section, count))
Error: Option 'aliases' in section 'board_pins' must have 2 elements
webhooks client 1971428568: New connection
webhooks client 1971428568: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971428568: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:56:04 2022 (1642398964.6 4315.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970272376: New connection
webhooks client 1970272376: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970272376: Disconnected
Restarting printer
Start printer at Mon Jan 17 05:56:15 2022 (1642398975.1 4326.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1 header
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2 header
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970253872: New connection
webhooks client 1970253872: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970253872: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:06:41 2022 (1642399601.7 4952.9)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1970852528: New connection
webhooks client 1970852528: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970852528: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:06:45 2022 (1642399605.9 4957.2)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1971403152: New connection
webhooks client 1971403152: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971403152: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:09:17 2022 (1642399757.8 5109.1)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1970469424: New connection
webhooks client 1970469424: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970469424: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:09:59 2022 (1642399799.2 5150.4)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1971418576: New connection
webhooks client 1971418576: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971418576: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:13:33 2022 (1642400013.7 5365.0)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1970168656: New connection
webhooks client 1970168656: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Transition to shutdown state: Shutdown due to webhooks request
Dumping 20 requests for client 1970168656
Received 5418.786223: {"id": 1732055760, "method": "info", "params": {}}
Received 5419.790033: {"id": 1731690384, "method": "info", "params": {}}
Received 5419.791351: {"id": 1731687664, "method": "info", "params": {}}
Received 5420.790794: {"id": 1731688400, "method": "info", "params": {}}
Received 5421.794536: {"id": 1731687664, "method": "info", "params": {}}
Received 5421.796713: {"id": 1731385392, "method": "info", "params": {}}
Received 5422.793632: {"id": 1731688176, "method": "info", "params": {}}
Received 5423.795271: {"id": 1731689520, "method": "info", "params": {}}
Received 5423.796604: {"id": 1731387344, "method": "info", "params": {}}
Received 5424.793797: {"id": 1731688368, "method": "info", "params": {}}
Received 5425.794514: {"id": 1731689520, "method": "info", "params": {}}
Received 5425.795847: {"id": 1731386800, "method": "info", "params": {}}
Received 5426.794230: {"id": 1731735760, "method": "info", "params": {}}
Received 5427.791125: {"id": 1740712976, "method": "info", "params": {}}
Received 5427.792460: {"id": 1731383440, "method": "info", "params": {}}
Received 5428.792835: {"id": 1731687632, "method": "info", "params": {}}
Received 5429.143987: {"id": 1731384304, "method": "info", "params": {}}
Received 5429.378009: {"id": 1731686608, "method": "info", "params": {}}
Received 5430.187086: {"id": 1732057552, "method": "info", "params": {}}
Received 5430.821751: {"id": 1731690288, "method": "emergency_stop", "params": {}}
Reactor garbage collection: (5403.824547053, 0.0, 0.0)
webhooks client 1970168656: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:14:41 2022 (1642400081.6 5432.9)
Unable to open config file /home/pi/klipper_config/printer.cfg
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/configfile.py", line 153, in _read_config_file
    f = open(filename, 'r')
IOError: [Errno 2] No such file or directory: '/home/pi/klipper_config/printer.cfg'
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 134, in _read_config
    config = pconfig.read_main_config()
  File "/home/pi/klipper/klippy/configfile.py", line 274, in read_main_config
    data = self._read_config_file(filename)
  File "/home/pi/klipper/klippy/configfile.py", line 159, in _read_config_file
    raise error(msg)
Error: Unable to open config file /home/pi/klipper_config/printer.cfg
webhooks client 1970709408: New connection
webhooks client 1970709408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1970709408: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:15:06 2022 (1642400106.2 5457.5)
===== Config file =====

=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 139, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/mcu.py", line 997, in add_printer_objects
    printer.add_object('mcu', MCU(config.getsection('mcu'), mainsync))
  File "/home/pi/klipper/klippy/mcu.py", line 554, in __init__
    self._serialport = config.get('serial')
  File "/home/pi/klipper/klippy/configfile.py", line 58, in get
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 33, in _get_wrapper
    % (option, self.section))
Error: Option 'serial' in section 'mcu' must be specified
webhooks client 1971418536: New connection
webhooks client 1971418536: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
webhooks client 1971418536: Disconnected
Restarting printer
Start printer at Mon Jan 17 06:16:10 2022 (1642400170.8 5522.0)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971426408: New connection
webhooks client 1971426408: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1971426408: Disconnected
Restarting printer
Start printer at Mon Jan 17 12:57:36 2022 (1642424256.7 29608.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971420096: New connection
webhooks client 1971420096: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Transition to shutdown state: Shutdown due to webhooks request
Dumping 20 requests for client 1971420096
Received 30639.059393: {"id": 1731489488, "method": "info", "params": {}}
Received 30641.059255: {"id": 1731486800, "method": "info", "params": {}}
Received 30643.057932: {"id": 1731546448, "method": "info", "params": {}}
Received 30645.055903: {"id": 1731546160, "method": "info", "params": {}}
Received 30647.055702: {"id": 1731738288, "method": "info", "params": {}}
Received 30649.055756: {"id": 1731572976, "method": "info", "params": {}}
Received 30651.056553: {"id": 1731575184, "method": "info", "params": {}}
Received 30653.056458: {"id": 1731739472, "method": "info", "params": {}}
Received 30655.059955: {"id": 1740713008, "method": "info", "params": {}}
Received 30657.056381: {"id": 1731384144, "method": "info", "params": {}}
Received 30659.059955: {"id": 1731383856, "method": "info", "params": {}}
Received 30661.058908: {"id": 1731384688, "method": "info", "params": {}}
Received 30663.059430: {"id": 1731383472, "method": "info", "params": {}}
Received 30665.043897: {"id": 1731384400, "method": "info", "params": {}}
Received 30667.046140: {"id": 1732059056, "method": "info", "params": {}}
Received 30669.060323: {"id": 1732055792, "method": "info", "params": {}}
Received 30723.051032: {"id": 1731383632, "method": "info", "params": {}}
Received 30743.580222: {"id": 1731573680, "method": "info", "params": {}}
Received 30744.228547: {"id": 1732058640, "method": "info", "params": {}}
Received 30744.768779: {"id": 1732057808, "method": "emergency_stop", "params": {}}
Reactor garbage collection: (30599.057043692, 30517.048510598, 0.0)
Attempting MCU 'mcu' reset
webhooks client 1971420096: Disconnected
Restarting printer
Start printer at Mon Jan 17 13:16:36 2022 (1642425396.8 30748.3)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970273856: New connection
webhooks client 1970273856: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970273856: Disconnected
Restarting printer
Start printer at Mon Jan 17 13:16:41 2022 (1642425401.4 30752.9)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1971376936: New connection
webhooks client 1971376936: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
Unhandled exception during post run
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 219, in run
    m.microcontroller_restart()
  File "/home/pi/klipper/klippy/mcu.py", line 922, in microcontroller_restart
    self._restart_arduino()
  File "/home/pi/klipper/klippy/mcu.py", line 884, in _restart_arduino
    serialhdl.arduino_reset(self._serialport, self._reactor)
  File "/home/pi/klipper/klippy/serialhdl.py", line 376, in arduino_reset
    ser = serial.Serial(serialport, 2400, timeout=0, exclusive=True)
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialutil.py", line 240, in __init__
    self.open()
  File "/home/pi/klippy-env/local/lib/python2.7/site-packages/serial/serialposix.py", line 268, in open
    raise SerialException(msg.errno, "could not open port {}: {}".format(self._port, msg))
SerialException: [Errno 2] could not open port /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00: [Errno 2] No such file or directory: '/dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00'
Restarting printer
Start printer at Mon Jan 17 13:16:52 2022 (1642425412.2 30763.6)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970436336: New connection
webhooks client 1970436336: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}
Attempting MCU 'mcu' reset
webhooks client 1970436336: Disconnected
Restarting printer
Start printer at Mon Jan 17 13:16:59 2022 (1642425419.7 30771.1)
===== Config file =====
[stepper_x]
step_pin = P2.2
dir_pin = P2.6
enable_pin = !P2.1
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.29
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_y]
step_pin = P0.19
dir_pin = P0.20
enable_pin = !P2.8
microsteps = 16
rotation_distance = 40
endstop_pin = !P1.28
position_endstop = 0
position_max = 310
homing_speed = 20

[stepper_z]
step_pin = P0.22
dir_pin = !P2.11
enable_pin = !P0.21
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[stepper_z2]
step_pin = P1.15
dir_pin = P1.14
enable_pin = !P1.16
microsteps = 16
rotation_distance = 8
endstop_pin = !P1.27
position_endstop = 0.0
position_max = 400

[extruder]
step_pin = P2.13
dir_pin = !P0.11
enable_pin = !P2.12
microsteps = 16
rotation_distance = 33.500
nozzle_diameter = 0.400
filament_diameter = 1.750
heater_pin = P2.7
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.24
control = pid
pid_kp = 22.2
pid_ki = 1.08
pid_kd = 114
min_temp = 1
max_temp = 260

[heater_bed]
heater_pin = P2.5
sensor_type = EPCOS 100K B57560G104F
sensor_pin = P0.25
control = pid
pid_kp = 54.027
pid_ki = 0.770
pid_kd = 948.182
min_temp = 0
max_temp = 130

[fan]
pin = P2.3

[mcu]
serial = /dev/serial/by-id/usb-Klipper_lpc1769_15A0FF0AA99869AF4114425EC52000F5-if00

[printer]
kinematics = cartesian
max_velocity = 200
max_accel = 3000
max_z_velocity = 100
max_z_accel = 100
	TMC2208 configuration

[tmc2208 stepper_x]
uart_pin = P1.10
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_y]
uart_pin = P1.9
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z]
uart_pin = P1.8
run_current = 0.650
stealthchop_threshold = 999999

[tmc2208 extruder]
uart_pin = P1.4
run_current = 0.800
stealthchop_threshold = 999999

[tmc2208 stepper_z2]
uart_pin = P1.1
run_current = 0.800
stealthchop_threshold = 999999

[board_pins]
aliases = 
	EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
	EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
	EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
	EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 157, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 143, in _read_config
    m.add_printer_objects(config)
  File "/home/pi/klipper/klippy/toolhead.py", line 599, in add_printer_objects
    config.get_printer().add_object('toolhead', ToolHead(config))
  File "/home/pi/klipper/klippy/toolhead.py", line 256, in __init__
    self.kin = mod.load_kinematics(self, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 142, in load_kinematics
    return CartKinematics(toolhead, config)
  File "/home/pi/klipper/klippy/kinematics/cartesian.py", line 29, in __init__
    above=0., maxval=max_accel)
  File "/home/pi/klipper/klippy/configfile.py", line 67, in getfloat
    note_valid=note_valid)
  File "/home/pi/klipper/klippy/configfile.py", line 40, in _get_wrapper
    % (option, self.section))
Error: Unable to parse option 'max_z_accel' in section 'printer'
webhooks client 1970254112: New connection
webhooks client 1970254112: Client info {'program': 'Moonraker', 'version': 'v0.7.1-300-g5f54a23'}