Basic Information: Printer Model: Prusa i3MK3S+ MCU / Printerboard: Einsy RAMBo Host / SBC klippy.log Describe your issue: Hello, I am trying to set up Klipper on Raspberry Pi 5. I installed Klipper via KIAUH. I am looking for a printer.cfg for Prusa i3MK3S+. I visited the following site bu…

Hi @printeruser , I used this config on my MK3S+.

Thanks. What did you do with Step. 2 of Install? Did you just skip it? In the past, I connected a Pi to the i3MK3S+ via a USB cable. Under what directory are we supposed to execute “Clone config git clone https://github.com/dz0ny/klipper-prusa-mk3s.git ~/printer_data/config/klipper-prusa-mk3s” ment…

[image] printeruser: Thanks. What did you do with Step. 2 of Install? Did you just skip it? In the past, I connected a Pi to the i3MK3S+ via a USB cable. For step 2, I connected a Pi to the Einsy with a USB cable. [image] printeruser: Under what directory are we supposed to execute “Clon…

FYI, now I’m using an SKR Mini E3 V3 for the extra sensor plugs, better stepper drivers, and 24V fans. Nothing wrong with the Einsy or config, just I needed something a bit different for all the mods I installed.

It seems that I might have successfully installed Klipper and flashed the i3MK3S+. Thank you very much. Since I have a E3D Revo 6 nozzle, is it better to perform another PID tuning and update the values in the printer.cfg file? How do I test if everything is working? Am I correct that if the print…

No problem! Yes. A PID tune is recommended and you can update the values in your config by using SAVE_CONFIG after. I’d try to home all axes, PID tune hotend and bed for good measure, then test a bed mesh. If anything goes wrong, use emergency stop I recommend the FYSETC PIS. When you restart from…

Unless you have any more questions, could you please mark one of my posts as a solution to mark this thread as solved?

I went to the LCD screen and used the knob to go to PID tuning. Then I selected Tune Hotend PID. The side fan kept spinning. The LCD screen only shows Tune Hotend PID and Tune Heatbed PID. Nothing else seems to be happening. After about 10 minutes, the fan stopped spinning but the screen remains th…

I would do this from Mainsail/Fluidd. Configuration checks - Klipper documentation Let’s break homing down into X, Y, and Z: Does homing X work? Does homing Y work? Does homing Z work? I found it on Amazon here . If it’s not available in your country, you can also try a KUSBA. If you get a standa…

Thanks. PID calibration done. How to do homing down in to X, Y and Z independently? I keyed in G28 X0.0 according to information from a webpage but the extruder moved to the far left. Issuing G28 X0.0 did not cause the extruder to move to the middle but it crashed the left with a loud sound. Becau…

[image] printeruser: How to do homing down in to X, Y and Z independently? To home XYZ independently, you can use G28 X, etc. [image] printeruser: Because of that, perhaps I should recalibrate the axes. Klipper doesn’t have auto axis calibration. Instead, follow the below procedure to…

Where are printer.cfg and enisy-rambo.cfg for Prusa i3MK3S+?

General Discussion

EddyMI3D April 10, 2025, 5:51am 14

You may read this: Understanding X and Y Axes Limits and Homing

Topic		Replies	Views
MK3S, Klipper, Bondtech, Mosquito, configuration help General Discussion	14	167	April 29, 2026
Confused putty says its right but klipper tells me no General Discussion	7	483	December 6, 2022
Install Klipper onto Prusa mk3s+ General Discussion	4	863	September 5, 2024
Need help creating a config for a frankensteined ender3 General Discussion	10	2699	September 15, 2023
Problems with basic configuration General Discussion	5	113	November 19, 2025

Where are printer.cfg and enisy-rambo.cfg for Prusa i3MK3S+?

Related topics