So running a cooling fan for my Pi is very easy: [temperature_sensor raspberry_pi] sensor_type: temperature_host min_temp: 0 max_temp: 100 [temperature_fan controller_fan] # Electronics fan PWM pin: PB5 max_power: 0.60 hardware_pwm: true control: watermark max_delta: 2 sensor_type: temperature_hos…

You can’t refer to the same temp source in two different sections. [temperature_sensor mcu_temp] sensor_type: temperature_mcu [temperature_fan octopus_fan] pin: PB5 max_power: 0.60 hardware_pwm: true control: watermark max_delta: 2 sensor_type: temperature_mcu min_temp: 10 max_temp: 80 t…

More than likely two trying to access temperature_host. Your EBB should also have this so it is getting it from the EBB and not your main mcu by default. sensor_mcu: EBBCan

[image] NAPCAL: More than likely two trying to access temperature_host. Yep, that’s the gist of the error I get. I’ll try your suggestion, thank you. Edit: do you mean like this: [IMG_8435] As that is what I currently have.

Yep. And if you want a temperature controlled fan for the RPi then you might have to comment out the RPi temp monitoring to use the temperature_host.

The RPi 4 already has OS temperature control for a PWM fan. [image] Raspberry Pi PWM Fan Speed Control - Embedded Computing Design As you probably know, Raspberry Pi single-board computers, especially Pi 4 models, can get quite hot. While passive cooling options are often good enough to…

[image] NAPCAL: The RPi 4 already has OS temperature control for a PWM fan. I’m running a 3B+. [image] NAPCAL: if you want a temperature controlled fan for the RPi then you might have to comment out the RPi temp monitoring to use the temperature_host. I have temp controlled fan for th…

[image] NAPCAL: And if you want a temperature controlled fan for the RPi then you might have to comment out the RPi temp monitoring to use the temperature_host. So even if I comment out all MCU temp sections including the rPi, except the main board MCU, then use Host for the main board MCU, i…

[image] [controller_fan] using raspi temp as input General Discussion first i had this, but this will give very jerky motion to the fans because they dont know wich signal to take #[duplicate_pin_override] #pins: PC8 #[controller_fan board_fans] #pin: PC8 #kick_start_tim…

Im not sure how that is relevant? I can trigger the fan via my rPi CPU temp without issue, what I cant is trigger them from the main board MCU. I dont understand why I get the “ADC” error but ModBot can get it working: [Upgrade Your Fans With Klipper Firmware]

[image] NAPCAL: You can’t refer to the same temp source in two different sections. Oh that makes sense - I now have it working after commenting out the below section, thank you. :pray: #[temperature_sensor mcu_temp] #sensor_type: temperature_mcu #min_temp: 0 #max_temp: 100

Did something change in the last few weeks. This does not work for me. Intially i had temp sensors set for both Pi and MCU, and they show on the chart in the main screen of mainsail. Then i tried to setup "{temperature fans, to get some fans to turn on and off depending on Pi temps, didn’t work. The…

How do you trigger fans from the Main MCU Temp?

General Discussion

NAPCAL May 3, 2023, 11:21pm 8

Topic		Replies	Views
Controller Board Cooling Fan(s) General Discussion	12	16316	April 2, 2024
Enclosure Fan config for MCU + Raspberry General Discussion	0	1252	July 5, 2022
How to help. Temps from Octupus MCU and EBB36 mcu General Discussion	6	562	January 25, 2025
[controller_fan] using raspi temp as input General Discussion	5	11768	May 23, 2022
Temperature_fan depending on the TMC2240 temperature? General Discussion	3	1955	March 25, 2024

How do you trigger fans from the Main MCU Temp?

Related topics