Basic Information: Printer Model: SunluS8 MCU / Printerboard:BTT SKR 1.4 Turbo klippy.log Describe your issue: Hi, Ive been researching for a few weeks about installing klipper on my sunlu S8 with an Skr 1.4 turbo and 2209 drivers and my 2 ender-3 with skrmini v2. I finally got around to try…

Even if I dont have the ID and it doesnt show up when connected by usb to anything? This is what has me worried. In KIAUH call 4) [Advanced] and then 5) [Get MCU ID] or run the command ls /dev/serial/by-id/* in the shell. 2. Copy the complete path as displayed, e.g. /dev/serial/by-id/usb-1a86…

Hi. I followed the directions from that page again and same issue. As I said previously the board wont show connected in device manager on my regular pc or show connection in Kiuah. I had an old laptop that I also installed kiuah on but decided not to use it. SInce no changes where made to the init…

Make sure you build for: In the klipper path issue the command: make distclean Then in make menuconfig LPC1768 or LPC1769(Turbo) with either 100MHz or 120MHz (Turbo) Leave all the rest of options alone Rename klipper.bin to firmware.bin Copy firmware.bin to the SD card Reboot the board Check S…

Hi. Yes thats exactly what I did. Step by step. I get the cur file on the SD card but its like the usb port just stops working after I flash. Happened to both boards using Rpi3b + and a laptop. Both firmware configured with kiuah script.

Did you try a different SD card? Good luck, hcet14

[image] hcet14: Did you try a different SD card? Just as importantly, what is your SD Card? I’m wondering if you have something too big/too fast that can’t be accessed by the SKR Turbo. As noted elsewhere, I keep a few (very old) 1G to 4GB SD Cards (both full size and micro) around as I kno…

Do it again and make extra sure you get the make settings correct: [grafik] I just tried with my old SKR 1.4T and it works flawlessly. A properly flashed Klipper serial for a SKR 1.4T needs to look like: klipper@bigtreetech-cb1:~/klipper$ ls /dev/serial/by-id/* /dev/serial/by-id/usb-Klipper_lpc…

I hadnt tried another sd card, just a different USB cable. I was using the 8gb sd card I think its class 10 (Its really small)that came with the sunlu s8. Ive used it for about the last year or 2 with that printer. Today I did try a 32gb class 10 sd card and same issue. sd card shows the bin file …

[image] Ellou: Should I try to connect with the Uart pins? Or any logs I can check to see what might have happened? You can try but I guess it will not make any difference [image] Ellou: if you sent me your bin file I should be able to flash it correct? When you set exactly these para…

Possibly Bricked my board

General Discussion

Sineos October 20, 2023, 9:29pm 2

No worry, your board is not bricked. Probably not correctly flashed. Closely follow Installing Klipper with KIAUH

Topic		Replies	Views
Cannot find MCU? General Discussion	16	844	December 3, 2024
Mcu not found while using kiauh on skr 1.4 turbo General Discussion	7	1291	July 3, 2023
MCU unable to connect BTT SKR Mini E3 V1.2 General Discussion	20	2263	October 14, 2023
'mcu': Unable to connect General Discussion	23	2102	June 2, 2024
MCU problems installing klipper on S1 pro General Discussion	20	1378	September 9, 2023

Possibly Bricked my board

Related topics