Basic Information: Printer Model: modified/redesigned HevOrt MCU / Printerboard: BTT Octopus v1.1 / stm32f446xx Version: v0.12.0-272-g13c75ea87 Host; Raspberry Pi 3 Version: v0.12.0-272-g13c75ea87 OS: Raspbian GNU/Linux 11 (bullseye) Distribution: MainsailOS 1.0.0 (bullseye) klippy.log …

Next topic with your printer. :frowning: Check this here: [image] TMC 'extruder' reports error: GSTAT: 00000001 reset=1(reset General Discussion Intermediate summary: Threads about this or related issues: Boards: BTT SKR E3 is by far leading the field BTT SKR 2 tw…

Thanks, yes, these Topics are mostly already known. But all these are about curing the symptoms. At the Moment my concern is, to understand what this error Message is about. As far as i have understood, this is not generated by Klipper, but handed trough from the stepper driver. I want to know, w…

[image] limefrog: yes, these Topics are mostly already known. But all these are about curing the symptoms. What you call the symptoms are the root causes. The symptom is the error message GSTAT Error 00000001 reset=1. This means that something is dragging your driver in a permanent reset cond…

[image] Sineos: This means that something is dragging your driver in a permanent reset condition. Yes, i want to understand how this is happening. What are the triggers? Does there exist a specification which explaines what boundary conditions initiate the message?

[image] limefrog: yes, these Topics are mostly already known. If you had read these threads, you would have noticed that this error is not raised by Klipper but by the TMC drivers, which are a product by Analog Devices. Klipper just passes on this message and considers it (rightfully) as imp…

We are checking that together and I pointed again towards wires and respective contacts but as first step swapping X and Y stepper drivers.

[image] Sineos: If you had read these threads, you would have noticed that this error is not raised by Klipper but by the TMC drivers… [image] limefrog: As far as i have understood, this is not generated by Klipper, but handed trough from the stepper driver. @Sineos This is crystal cle…

Not being the expert, but I’m afraid the “simple” answer that you are looking for, does not exist. The error is more or less generic The reasons that has so far been discussed and also validated are as well unspecific: Defect hardware that has somehow an impact on the SPI bus communication (one i…

At the moment it seems i can add a new approach: I intentionally made a complete power drain for 10 hours, to discharge any capacitor and let every Transistor compensate from residual charges. Whilst yesterday it was impossible to finalize the first round of Z-tlting, i was able to start a print …

… The problem isn’t gone. So the power relief is not the final solution. But i’ m able to observe a correlation between the temperature inside the housing and the tendency to throw the error message. So the power relief is not the solution, but temperature relief has influence. If the machine bec…

Suddenly GSTAT Error 00000001 reset=1

General Discussion

LifeOfBrian September 11, 2024, 6:00am 2

Next topic with your printer.

Check this here:

Topic		Replies	Views
TMC 'stepper' reports GSTAT: 00000001 reset=1(Reset) Knowledge Base	0	1694	November 1, 2024
TMC 'extruder' reports error: GSTAT: General Discussion	2	870	March 20, 2024
TMC 'extruder' reports error: GSTAT: 00000001 reset=1(reset General Discussion	81	32024	April 7, 2024
GSTAT problem on klipper General Discussion	2	86	November 8, 2024
"Extruder" reports GSTAT: 00000001 reset=1(Reset) General Discussion	7	2563	June 12, 2025

Suddenly GSTAT Error 00000001 reset=1

Related topics