So have had this happen tree times in a row now. Tried re-slicing, updated to latest klipper, and atm testprinting with swapped cable with theY axis one. I’m reading it most likely could be wiring, voltage or steppers. And also seeing that it could be PA related, and in one case usb related. (Will …

I guess these caps you mention are against interference from the suppply, not for ESD protection. See https://www.trinamic.com/fileadmin/assets/Products/ICs_Documents/TMC2209_Datasheet_V103.pdf page 14.

Yes, the mentioned capacitors (if missing) would rather end in GSTAT: uv_cp=1 error. Your board has those capacitors. So better forget my post from above :unamused: It might be a good idea to solder the capacitors mentioned on page 14 on the left schematic to your board. I think it can be done easi…

I am having this issue on a BTT Manta M8P with CB1 on a Tronxy X5SA Pro/ VZBot conversion. It started out on the Y stepper. Following multiple threads, I tried swapping drivers (Same issue on Y), swapping wires (Same issue on Y), swapping steppers (Issue switched to X). So I replaced both X and Y st…

Small update here, as something funny happend just now. Got a gstat stepper reset error on Z, because of statics spark (wearing my rubber sandals, that create a ton of statics…) but funny is that this happend when i touched the printer sitting next to the printer in use. Like a foot apart. So that…

Joining the list with my SKR2 and ender 5. TMC ‘extruder’ reports error: GSTAT: 00000001 reset=1(Reset) This isn’t klipper specific, on marlin my extruder will drop steps from 16 to 8 when this happens and start to overheat and extrude we too much filament. It always seems to be the extruder …

Same problem here with an octopus 1.1 on a Sovol SV02 machine. I changed the motor three times, and the extruder wires twice. I admit I still have a cable extender since I couldn’t find long enough extruder wires until now. I’m looking for a good cable/wires.

@Peggy and @some-klipper-user Have you tried to put some active cooling across the TMC drivers? You could just put a small fan blowing air across the drivers and see if they stabilize.

我想我解决了这个报错，引发这个报错的原因是机器的震动

在我把机器从桌搬到地上之后出现了这个报错，我尝试了各种办法，结果发现是因为搬到地上后，机器没有桌子吸收震动，倒是机器的震动传导到主板导致的报错，而且几乎是在同一个地方，我通过给主板支架增加缓冲解决了这个问题

@jjarosz I solved my problem by shorting the direct drive extruder wires

TMC 'extruder' reports error: GSTAT: 00000001 reset=1(reset

General Discussion

Topic		Replies	Views
TMC 'extruder' reports error General Discussion	3	1728	February 9, 2022
Suddenly GSTAT Error 00000001 reset=1 General Discussion	12	354	September 17, 2024
TMC 'stepper_x' reports error: GSTAT: 00000001 reset=1(Reset) General Discussion	15	17858	May 20, 2022
TMC 'stepper' reports GSTAT: 00000001 reset=1(Reset) Knowledge Base	0	1761	November 1, 2024
'extruder' reports error: drv_status: 40140060 s2vsb=1(shorttosupply_b!) ola=1(openload_a!) cs_actual=20 stealth=1 General Discussion	19	371	December 17, 2025

TMC 'extruder' reports error: GSTAT: 00000001 reset=1(reset

Related topics