|
About the Features category
|
|
0
|
906
|
March 20, 2021
|
|
Power-loss / crash recovery without saving anything during the print: measure where the nozzle stopped
|
|
4
|
125
|
October 30, 2026
|
|
[Feature Request] Move until trigger
|
|
0
|
60
|
October 19, 2026
|
|
Configurable HD44780 command delay (PR #7356) - feedback/review wanted
|
|
8
|
178
|
October 6, 2026
|
|
Min speed and initial speed for tacho fans
|
|
2
|
70
|
September 17, 2026
|
|
Optional randomization ("fuzz") of probe points for QUAD_GANTRY_LEVEL / Z_TILT to reduce build-surface wear with contact (nozzle) probes
|
|
0
|
79
|
August 29, 2026
|
|
Ender 3 printing stops immediately after reaching the set temperature when using Klipper
|
|
1
|
77
|
August 16, 2026
|
|
Suggestion: move smooth_time from heaters to temperature sensors
|
|
2
|
320
|
July 19, 2026
|
|
Support for HDSC chips (HC32F460)
|
|
169
|
20429
|
July 9, 2026
|
|
[Feature Request] delta_calibrate Convergence Integer
|
|
1
|
128
|
July 8, 2026
|
|
Feature Request: adc_SENSOR_WITH_NON_TEMPERATURE_UNIT
|
|
0
|
69
|
June 12, 2026
|
|
Reduced accuracy for supports
|
|
7
|
237
|
June 11, 2026
|
|
[IDEX] Nozzle position calibration with a second load cell probe
|
|
10
|
427
|
May 10, 2026
|
|
In-Menu Multi-Extruder Selection for Heating and Loading
|
|
0
|
96
|
April 7, 2026
|
|
Steps to add a new kinematic type
|
|
0
|
207
|
March 20, 2026
|
|
SS1306 / 0.9" OLD Display Module - variable number of lines
|
|
3
|
152
|
March 18, 2026
|
|
Feature request discussion
|
|
3
|
154
|
March 15, 2026
|
|
Continuous mesh probing with inductive probe
|
|
2
|
170
|
March 14, 2026
|
|
Implement ADXL355 support
|
|
0
|
163
|
March 4, 2026
|
|
Angular velocity scaling for polar 3d printers
|
|
0
|
81
|
February 21, 2026
|
|
Deceleration on homing moves
|
|
11
|
443
|
January 25, 2026
|
|
BDsensor Intagration into klipper Main library
|
|
1
|
137
|
January 24, 2026
|
|
Feature request: extruder temperature offset option in API/UI
|
|
1
|
116
|
January 4, 2026
|
|
Spline-GCodes (G5)
|
|
3
|
292
|
December 28, 2025
|
|
It is not possible to cancel printing immediately after the start, until the heating occurs!
|
|
20
|
4556
|
December 23, 2025
|
|
Bed mesh / bed temperature lookup table (LUT)
|
|
2
|
132
|
December 22, 2025
|
|
LCD open menu and select item from GCode
|
|
0
|
68
|
December 19, 2025
|
|
Pressure advance in all stepper extruders
|
|
21
|
748
|
November 25, 2025
|
|
QGL auto unsagged
|
|
0
|
117
|
November 16, 2025
|
|
PWM Scaled to Toolhead Speed
|
|
13
|
471
|
November 14, 2025
|