Basic Information: Printer Model: Ender 3 MCU / Printerboard: Creality board 1.1.4 (firmware 1.1.6) klippy.log Describe your issue: So i use Ender 3 and after 2 spools of PLA finally got first spool of Nebula PETG(Its my target filament type). It prints very nice at 225C with print speed of 6…

I just did another search on the Creality 1.1.4 board’s drivers and there is confusion as to whether or not there are A4988s or TMC2209s. If I look at the usable printer.cfg for the printer: Klipper3d/klipper/blob/master/config/printer-creality-ender3-2018.cfg # This file contains …

I will install klipper no problem on this pc i even did this on wsl2 in windows but it was just install i didnt tested it. Cant see anything related to stepper motor driver model in config file. Problem is what calibrations i need to do and in what order i have to do it. Lets say i have klipper i…

Install Klipper on your host system. I suggest you use KIAUH Create the firmware for your 1.1.4 controller board and burn it in Select the basic printer.cfg (the link I gave you above: https://github.com/Klipper3d/klipper/blob/master/config/printer-creality-ender3-2018.cfg ) Connect your 1.1.4 cont…

Do i need to? Calibrate Extruder(that test for 100mm extrusions) Calibrate PID for temperatures Calibrate E-Steps for dimensional accuracy Retraction Speed Temperature Tower There will be probably more of those i dont remember now all. Most of those i did but it was on current marlin. But proba…

Unless you’ve changed the hot end, then what’s in the default printer.cfg I linked will be fine, at least to start. Honestly, you’re getting ahead of yourself. Get your host up and running as well as connected to the Creality 1.1.4 board. It’s going to be a non-trivial exercise for you.

Okay will do tomorrow i hope, when arduino uno with cables and accelerometer(gy521-mpu6050 that seller didnt had adxl but should work fine) come in package. Thanks for help. I will probably do more posts i bet :smiley: So laters mate.

[image] Rafi: I will install klipper no problem on this pc i even did this on wsl2 in windows but it was just install i didnt tested it. Just as a warning: Running Klipper in a Virtual Machine (VM)

Ok. So i have Ubuntu Server installed on ssd, Burned bootloader (with marlin 1.9.1 just to check if its all good with flash). Installed Klipper, Moonraker, Mainsail. So to flash i go Advanced/Build only/ Micro-controller Architecture(Atmega AVR) Processor model (atmega1284p) Processor speed (16…

[image] Installing Klipper with KIAUH Knowledge Base Preface The official installation instructions use Octoprint as a control interface. Nowadays, most setups involve Moonraker and fluidd / Mainsail as the primary ways to interact and control a Klipper printer…

When i go Advanced/Get MCU ID in kiauh i get message [No MCU found] When i flash i have communication interface UART only. I have 1.1.4 8bit board, i dont know if it support it. when i do ls /dev/serial/by-id i got ls: cannot access ‘/dev/serial/by-id’: No such file or directory message

Klipper worth installing? Using PETG only

General Discussion

Sineos September 29, 2023, 6:04am 14

Just as a warning: Running Klipper in a Virtual Machine (VM)

Topic		Replies	Views
Honestly im about to give up on klipper, its just getting ridiculous at this point General Discussion	37	3500	May 1, 2024
Ender 3 V2 not connecting General Discussion	30	4050	September 15, 2023
Leapfrog Bolt pro - upgrade? General Discussion	102	1252	January 14, 2026
How to connect klipper to Makerbot Replicator 2X？ General Discussion	77	9862	May 6, 2024
Extra Klippy so it can also work with a dispenser instead of an extruder General Discussion	28	607	March 29, 2024

Klipper worth installing? Using PETG only

Related topics