Basic Information Geeetech A10T GT2560 V4.1 Is there somebody that use the Geeetech a10t with klipper? I’m trying to get it running… I hope there is somebody that can help? klippy .zip (12.9 KB)

[image] so if I ask some temp. something happens… and also my heater bed gets hotter… :slight_smile: so I think the connection between the raspberry pi and the printer is okay? all now is to configure the Printer.cfg till everything is okay? So how do I make 3 extruder motors, but 1 hot end… […

[image] Swets: what is that warning? important? [image] Swets: and this? in Fluidd? Honestly @Swets : All your topics so far have only one source: You copy/paste some stuff from I-don’t-know-where without understanding it and possibly not needing it. And on top of that, you do it even b…

Yes you are right… but even you say to use a printer.cfg: "Maybe check against https://github.com/ArmJo/Geeetech-A10-Klipper-GT2560v3-modded/blob/main/printer_no_mods.cfg " I have 4 or 5 different printer.cfg … and I don’t know what basic functionality is… So that’s why I ask what to do now… what…

“The second one comes from the fact that you again copied some update settings in the moonraker.conf without having installed the program that moonraker should be able to update, i.e. crowsnest.” I have copied some settings? how did i do that? I never did something with moonraker.conf? and then …

How did you install your setup? In the moonraker.conf you should find a setting block starting with: [update_manager crowsnest] If you do not have crowsnest installed then delete the entire block. If you have it installed then we need to check what is happening. [image] Swets: so what are th…

for the ender3 was a printer.cfg, and i didn’t change anything in that file… and I installed everything with kiauh… with a YouTube movie for the Ender3v2 printer… and it works, and I never look at it… but because I like it, I want it on the geeetech printer also. But there are no tutorials and mov…

Just checked, only heater_pin PB4 and sensor pin PK3 are responding. Sensor_pins Pk0 and Pk1 give an ADC error… so there is no sensor… And if I check heater_pin PE4 or PE5 with sensor PK3 I also get an error after a while because the is no heat feedback… so I guess the heaters are already parallel. …

[image] okay… If I extrude T0, only the middle one is running, T1 , two are running… T2 only the left one is running…

[image] Swets: here the drawing Mainboard GT2560 V4.1B schematic… I try to get the pinout the same as this drawing… Just to make things clear. Is this GT2560V4.1BSCHA10T-1.pdf (127.1 KB) the schematics you are working with?

Yes?.. Went the original firmware was in the printer , on the LCD by info there was GT2560 V4.1 by geeetech I only found the drawing for 4.1B so I think it is the right one… and al the pins for the stappers are right, because just print something … with UltiMaker Cura tend it to the Geeetech… an…

Geeetech a10t and klipper

General Discussion

EddyMI3D November 12, 2023, 10:06pm 52

Closed by request of the OP

Goes on in:

Topic		Replies	Views
3 extruders, Geeetech A10T General Discussion	17	1027	November 15, 2023
How to diagnose why the Geeetech A10x display shows nothing General Discussion	20	3517	December 18, 2024
Leapfrog Bolt pro - upgrade? General Discussion	102	1222	January 14, 2026
Klipper worth installing? Using PETG only General Discussion	25	3297	October 2, 2023
How to connect klipper to Makerbot Replicator 2X？ General Discussion	77	9838	May 6, 2024

Geeetech a10t and klipper

Related topics