|
It was a misstake to bring it up
|
|
3
|
65
|
May 4, 2025
|
|
CANBUS bytes_invalid and extruder motor
|
|
4
|
57
|
May 6, 2025
|
|
Load Cell Design
|
|
70
|
11711
|
May 6, 2025
|
|
Service "klipper" not allowed (linuxDeploy Android)
|
|
2
|
32
|
May 6, 2025
|
|
First Klipper Build Actuator Help
|
|
7
|
30
|
May 5, 2025
|
|
How to add Emergency Z-endstop in Klipper?
|
|
6
|
75
|
May 5, 2025
|
|
Upgraded to Klipper all working but display light but nothing else
|
|
5
|
40
|
June 5, 2025
|
|
Section 'scanner' is not a valid config section
|
|
4
|
31
|
May 5, 2025
|
|
Generic 3950 Thermistor not working when attached to toolboard
|
|
3
|
41
|
May 5, 2025
|
|
Lost communications with MCU
|
|
8
|
67
|
May 5, 2025
|
|
Improved MCU connection error messages
|
|
18
|
250
|
May 5, 2025
|
|
Adaptive mesh will not clear for second print job
|
|
2
|
45
|
May 5, 2025
|
|
Thoughts on homing support in Klipper
|
|
15
|
507
|
May 4, 2025
|
|
Feature Request: Multiple Probes
|
|
3
|
88
|
May 4, 2025
|
|
Print jobs paused mid-print even there was lots of filament remaining
|
|
12
|
60
|
June 4, 2025
|
|
Feature request: extend protocol with UART commands
|
|
11
|
3077
|
May 4, 2025
|
|
Klipper Internal error on command:"G1"
|
|
33
|
233
|
May 4, 2025
|
|
A SIMPLE SOLUTION TO THE “ Move exceeds maximum extrusion” ERROR
|
|
0
|
60
|
May 4, 2025
|
|
Set up blower fan for stealthburner SB2209 [RP2040] canbus
|
|
8
|
80
|
May 3, 2025
|
|
Experiment with automated mcu flashing
|
|
13
|
1537
|
May 3, 2025
|
|
My accelerometer does not work
|
|
3
|
39
|
May 3, 2025
|
|
Valid STEP pins on STM32F407
|
|
5
|
30
|
May 3, 2025
|
|
START_PRINT Gcode error
|
|
3
|
59
|
May 3, 2025
|
|
SB2209 (RP2040) Neopixel not turning on
|
|
7
|
81
|
May 3, 2025
|
|
Cannot obtain mcu serial following firmware update
|
|
5
|
40
|
May 2, 2025
|
|
Thermal runaway
|
|
34
|
228
|
May 2, 2025
|
|
How to make the vertical wall more even, better looking?
|
|
0
|
30
|
May 2, 2025
|
|
V0.13.0-51 broke tool changers
|
|
3
|
95
|
May 2, 2025
|
|
Cannot setup a generic_heater for my enclosure (MCU 'mcu' shutdown: Missed scheduling of next digital out event)
|
|
7
|
52
|
May 2, 2025
|
|
Longer lk5 pro with skr mini e3 v3 cant get the z motors to work
|
|
6
|
62
|
May 1, 2025
|